This patch adds the header file asm/spi.h and board specific code for the
r2d board. The header file contains a structure that should be used to
point out a single spi bus. The board specific code for r2d is updated with
such a structure for the new spi_sh_sci driver. The structure contains a
chip select callback plus information about the R9701 rtc chip which is
attached to the spi bus.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the board specific irq code for r7780rp. The new code is
very similar to the other highlander implementations, with the exception that
the r7780rp handles pci interrupts using IRL. To simplify the pci code and
use the same interrupt numbers as r7780mp and r7785rp we hook in to the
cpu specific pci vectors.
The pci interrupts and the push switch all work well with and without this
patch. CF and AX88796 are not ok though and the source of the problem is
unknown at this point. The AX88796 does for not detect it's proper mac
address (IPL gets it right) and the kernel hangs on CF access. As a workaround
this patch removes the CF and the AX88796 from the platform datain case of
r7780rp.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the dreamcast use the recently added declared coherent
memory functions to point out the memory window suitable for dma.
Apart from cleaning up, this gives the dreamcast a proper memory allocator
for pci dma memory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Renesas Technology Europe SDK7780 board.
Signed-off-by: Nicholas Beck <nbeck@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch tells the sm501 mfd driver to build platform data for the
sm501 usb host driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes redundant irq handling code together with unused
consistent alloc code. R2D uart setup code is changed to use
sm501-regs.h and unused header files are removed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds timings to drive a Sharp LQ104V1DG21 lcd panel that can
be hooked up to R2D-1 or R2D-PLUS. The sm501fb driver should leave the
pins FPEN and VBIASEN alone, and this patch instructs the driver to do
so by not setting flags flags for these pins.
This patch works best together with the patch posted to the
linux-fbdev-devel list "sm501fb: control panel pin usage with platform
data flags", but this patch can be merged independently.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes CF support for R2D-1 boards. Both R2D-1 and
R2D-PLUS are equipped with CF IRQs, but the R2D-1 FPGA version
seem to deliver IRQ spikes with certain CF cards during libata
probing. This patch enables polling for R2D-1 as a workaround
for this broken FGPA logic.
R2D-1 CF support was recently introduced by commit:
43f4b8c757.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This will force the snapgear boards to use the on-chip SH RTC instead,
until the rtc-ds1302 driver is merged. The current code is broken
and hasn't built in some time, so just kill it off and get the board
working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Access size to LED is not added on Solution Engine series.
LED doesn't work. Fixed this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R7780RP can't do byte-sized accesses to CF, so needs to do word
sized access with low-byte masking. This same problem exists
on older versions of the R2D, with the same workaround having
been implemented in 43f4b8c757
there. Follow that change for the highlander boards.
This does not impact R7780MP or SH7785 based Highlander modules.
If you're unfortunate enough to be stuck with an R7780RP, this
patch is for you!
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the ax88796 driver on highlander boards.
Implemented using the 93cx6 EEPROM support introduced by commit-id
89e536a190.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables building for both R2D-PLUS and R2D-1 boards. All code is
already in place except for the Kconfig limitation. This is useful if you
want to run the same binary on both R2D-PLUS and R2D-1 boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the R2D-PLUS and R2D-1 board detection code. Tested on two
R2D-PLUS and two R2D-1 boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This update moves the flash mapping for the Magic Panel into the board
setup. It also removes references to the old MTD mapping option in the
defconfig.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the port calculation logic for non-SuperIO accesses,
before these were always matching the MRSHPC base, now just make
sure the original port is handed back if it's not in the I/O port
range.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Most boards use 8 or 16-bit access for the LED bank, se7206
needs 32. There's only 8 individual LEDs however, each with
a 'special' value in terms of logical ordering. Go FPGA, go!
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The port routines were logically inverted, and the MRSHPC range had
no upper bound, causing 8 and 16-bit port I/O to get mangled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) based Magic Panel R2
board.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ0->IRQ3 need to be an IRQ mode for these to work, fix them up.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The vector changed, so follow the INTC changes for the new vector.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Build fixes for the hp6xx APM code, as well as some adjustments for
the battery values.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the highlander irq code for r7780mp and r7785rp.
The same strategy as for the new R2D code is used here - the board
specific interrupts are now starting from HL_FPGA_IRQ_BASE. The code
for r7780rp is not touched due to lack of hardware.
Tested with CF, AX88796 on r7780mp and r7785rp. The touch switch
interrupt has also been tested on r7780mp.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following fixes:
- Adds sh7785 support to CONFIG_EARLY_SCIF_CONSOLE_PORT.
- Removes duplicate include from rts7751r2d irq code.
- Removes CONFIG_CPU_HAS_INTC from sh7720 Kconfig entry.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We were abusing the resource size for the number of bits, this
has been reworked using proper platform data, so this can be
tidied up now. Boards in general only have a 1-byte wide resource,
which the ioremap_nocache() case already handles.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add some flags for the heartbeat driver, and kill off some duplication
in the bit positions for the boards that don't have special cases.
This also allows for variable access widths and inversion.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the intc core improved it is now possible to put the intc data
structures in the initdata section.
Version two of this patch puts the __initdata inside DECLARE_INTC_DESC()
and removes the __initdata included in the board specific r2d code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch replaces all instances of CONFIG_VOYAGERGX with
CONFIG_MFD_SM501. While at it we make sure the r2d code compiles
both with and without SM501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the board specific interrupt code for r2d to make
use of intc. While at it we improve the Kconfig to avoid confusion.
- Two sets of interrupt tables exist - one for R2D-1 and one for R2D-PLUS.
- R2D-1 and R2D-PLUS use the same irq constants.
- R2D-1 has AX88796 support, R2D-PLUS does not hook up that IRQ.
- R2D-PLUS has KEY support, R2D-1 does not hook up that IRQ.
- The number and order of IRQ values are disconnected from register bits.
- Interrupt sources now start from IRQ 100.
- The machvec demux function converts from irlm IRQ 0-14 to IRQ 100++.
Tested on R2D-1 and R2D-PLUS boards.
Version 2 adds CONFIG_RTS7751R2D_1 and CONFIG_RTS7751R2D_PLUS together
with intc structured as __initdata.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we have a way of enabling the IRQs, hook up the platform
devices and wrap in to ILSEL for mapping the vectors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm