The ethtool EEPROM interface is really meant for exposing chip
configuration, not BootROM configuration.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Falcon board config is invalid, we cannot proceed - we do not
have a valid board type to pass to falcon_probe_board(), and if we
kluge that to work with an unknown board then other initialisation
code will crash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mcfw *never* sends CMDDONE when rebooting. Changing this so that it always
sends CMDDONE *before* REBOOT is easy on Siena, but it's not obvious that we
could guarantee to be able to implement this on future hardware.
Given this, I'm less convinced that the protocol should be changed.
To reiterate the failure mode: The driver sees this:
issue command
receive REBOOT event
Was that reboot event sent before the command was issued, or in
response to the command? If the former then there will be a subsequent
CMDDONE event, if the latter, then there will be no CMDDONE event.
Options to resolve this are:
1. REBOOT always completes an outstanding mcdi request, and we set
the credits count to ignore a subsequent CMDDONE event with
mismatching seqno.
2. REBOOT never completes an outstanding mcdi request. If there is
no CMDDONE event then we rely on the mcdi timeout code to complete
the outstanding request, incurring a 10s delay.
I'd argue that (2) is tidier, but that incurring a 10s delay is a little
needless. Let's go with (1).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we enable PMA/PMD loopback this automatically sets RXIN_SEL
(inverse polarity for RXIN). We need to clear that bit during the
soft-reset sequence, as it is not done automatically.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not want to shut down the board based on a fault that has
already been cleared.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set both the 'maximum' and critical temperature limits for LM87
hardware monitors on Falcon boards. Do not shut down a port until the
critical temperature is reached, but warn as soon as the 'maximum'
temperature is reached.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some errors are expected, e.g. when sending new commands to an MC
running old firmware. Only the caller of efx_mcdi_rpc() can decide
what is a real error. Therefore log the error responses with
netif_dbg().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions and variable static. Do some rearrangement
of the string table stuff to put it where it gets used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The filter engine will time-out and ignore filters beyond
200-something hops. We also need to avoid infinite loops in
efx_filter_search() when the table is full.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This board never went into production, but some engineering samples
are in use.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFN4111T never reached production and is not being used for internal
or customer testing.
Since we have no production Falcon boards using the SFT9001 or the
GMAC, remove support for them as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/filter.c: In function ‘efx_probe_filters’:
drivers/net/sfc/filter.c:422: error: implicit declaration of function ‘vmalloc’
drivers/net/sfc/filter.c:422: warning: assignment makes pointer from integer without a cast
drivers/net/sfc/filter.c: In function ‘efx_remove_filters’:
drivers/net/sfc/filter.c:442: error: implicit declaration of function ‘vfree’
Signed-off-by: David S. Miller <davem@davemloft.net>
For backward compatibility, add it at the end.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires some reorganisation of channel setup and teardown to
ensure that we can always roll-back a failed change.
Based on work by Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow the ring size to be specified in non
power-of-two sizes (for instance to limit
the amount of receive buffers).
- Automatically size the event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow for reallocation of channel structures and rings.
Change module parameter separate_tx_channels to be read-only, since we
now require its value to be constant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changes to the way channels and queue structures
are allocated, revise the macros and functions used to look up and
iterator over them.
- Replace efx_for_each_tx_queue() with iteration over channels then TX
queues
- Replace efx_for_each_rx_queue() with iteration over channels then RX
queues (with one exception, shortly to be removed)
- Introduce efx_get_{channel,rx_queue,tx_queue}() functions to look up
channels and queues by index
- Introduce efx_channel_get_{rx,tx}_queue() functions to look up a
channel's queues
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we allocate DMA descriptor rings and event rings using
pci_alloc_consistent() which selects non-blocking behaviour from the
page allocator (GFP_ATOMIC). This is unnecessary, and since we
currently allocate a single contiguous block for each ring (up to 32
pages!) these allocations are likely to fail if there is any
significant memory pressure. Use dma_alloc_coherent() and GFP_KERNEL
instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_over_errors appears to be intended as a count of packets that
overflow a packet buffer in the NIC. Given that we implement a
cut-through receive path, this should always be 0.
rx_dropped appears to be the correct counter for packets dropped due
to lack of host buffers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculating rx_bad as rx_packets - rx_good is unnecessary and
incorrect, since rx_good does not include control frames (e.g.
pause frames) and rx_packets does.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eedc765ca4 merged changes from
net-2.6 that added and then removed efx_nic::port_num, which was also
added in net-next-2.6. The end result should be that it is removed,
since it is now unused.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ethtool to query the number of RX rings, the fields used in RX
flow hashing and the hash indirection table.
Allow ethtool to update the RX flow hash indirection table.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_op_set_flags() does not check for unsupported flags, and has
no way of doing so. This means it is not suitable for use as a
default implementation of ethtool_ops::set_flags.
Add a 'supported' parameter specifying the flags that the driver and
hardware support, validate the requested flags against this, and
change all current callers to pass this parameter.
Change some other trivial implementations of ethtool_ops::set_flags to
call ethtool_op_set_flags().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insertion of the Falcon hash is unreliable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will use this hash key for Toeplitz IPv4 hashing too.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hash appears immediately before the packet data, not at the
beginning of the buffer. This means we can easily use negative offsets
from the start of packet data, so adjust the data and length at the
top of __efx_rx_packet() instead of wherever we consume the hash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace EFX_ERR() with netif_err(), EFX_INFO() with netif_info(),
EFX_LOG() with netif_dbg() and EFX_TRACE() and EFX_REGDUMP() with
netif_vdbg().
Replace EFX_ERR_RL(), EFX_INFO_RL() and EFX_LOG_RL() using explicit
calls to net_ratelimit().
Implement the ethtool operations to get and set message level flags,
and add a 'debug' module parameter for the initial value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exposes the port number to userland through sysfs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_errors is defined as 'bad packets received', but we are currently
including various overflow errors as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insert a structure at the start of the shared page that
tracks the dma mapping refcnt. DMA into the next cache
line of the (shared) page (plus EFX_PAGE_IP_ALIGN).
When recycling a page, check the page refcnt. If the
page is otherwise unused, then resurrect the other
receive buffer that previously referenced the page.
Be careful not to overflow the receive ring, since we
can now resurrect n receive buffers in a row.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cut-through design of the receive path means that packets that
fail to match the appropriate MAC filter are not discarded at the MAC
but are flagged in the completion event as 'to be discarded'. On
networks with heavy multicast traffic, this can account for a
significant proportion of received packets, so it is worthwhile to
recycle the buffer immediately in this case rather than freeing it
and then reallocating it shortly after.
The only complication here is dealing with a page shared
between two receive buffers. In that case, we need to be
careful to free the dma mapping when both buffers have
been free'd by the kernel. This means that we can only
recycle such a page if both receive buffers are discarded.
Unfortunately, in an environment with 1500mtu,
rx_alloc_method=PAGE, and a mixture of discarded and
not-discarded frames hitting the same receive queue,
buffer recycling won't always be possible.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Pull the loop handling into efx_init_rx_buffers_(skb|page)
- Remove rx_queue->buf_page, and associated clean up code
- Remove unmap_addr, since unmap_addr is trivially calculable
This will allow us to recycle discarded buffers directly
from efx_rx_packet(), since will never be in the middle of
splitting a page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that efx_fast_push_rx_descriptors() must only run
from efx_process_channel() [NAPI], or when napi_disable()
has been executed.
Reimplement the slow fill by sending an event to the
channel, so that NAPI runs, and hanging the subsequent
fast fill off the event handler. Replace the sfc_refill
workqueue and delayed work items with a timer. We do
not need to stop this timer in efx_flush_all() because
it's safe to send the event always; receiving it will
be delayed until NAPI is restarted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Formerly, efx_test_eventq_irq() assumed it was the only user of
driver generated events. Allow it to interoperate with other users.
We can create more than 16 channels, so align event codes with
a multiple of 256 not 16.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been observed that some phys (such as the qt2025c) can
do down-up-down-up transitions, presumably as pcs block lock
settles down.
The loopback selftest will start sending data immediately
after the link comes up. Work around this by waiting for
the link state to stay up for two consecutive polls, rather
than one.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the ethtool code paths keep them in sync, but we need
to ensure they are sync'd at start of day. Matches the sft9001
driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions a PHY may backpressure Falcon B0
in such a way that flushes timeout. In normal circumstances
the phy poller would fix the PHY, and the flush could complete.
But efx_nic_flush_queues() is always called after efx_stop_all(),
so the poller has been stopped. Even if this weren't the case,
how long would we have to wait for the poller to fix this? And
several callers of efx_nic_flush_queues() are about to reset
the device anyway - so we don't need to do anything.
Work around this bug by scheduling a reset. Ensure that the
MAC is never rewired back into the datapath before the reset
runs (we already ignore all rx events anyway).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_pm_freeze() sets efx->state = STATE_FINI, which means
efx_reset_work() will abort any scheduled resets.
efx_pm_thaw() should reschedule efx_reset_work() again,
since a freeze/thaw will not have reset the hardware.
This bug was spotted by inspection - there is no real world example of
this happening.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of its members are constant capabilities, not configuration. The
new name is also consistent with the name of the pointer to it in
struct efx_nic and the names of structures used by other PHY drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a core TX queue and 2 hardware TX queues for each channel.
If separate_tx_channels is set, create equal numbers of RX and TX
channels instead.
Rewrite the channel and queue iteration macros accordingly.
Eliminate efx_channel::used_flags as redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes no immediate difference, but we definitely do not want
to test all TX queues once we allocate a pair of TX queues to each
channel.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for this to be unsigned long; make it unsigned int.
It does need a line in kernel-doc, so add that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently TX completions do not count towards the NAPI budget. This
means a continuous stream of TX completions can cause the polling
function to loop indefinitely with scheduling disabled. To avoid
this, follow the common practice of reporting the budget spent after
processing one ring-full of TX completions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When set, an event is not sent whenever periodic MAC statistics are
raised. This avoids unnecessary wake-ups.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parity errors in different blocks of SRAM may set one of two different
interrupt flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena has two problems with legacy interrupts:
1. There is no synchronisation between the ISR read completion,
and the interrupt deassert message.
2. A downstream read at the "wrong" moment can return 0, and
suppress generating the next interrupt.
Falcon should suffer from both of these, and it appears it does.
Enable EFX_WORKAROUND_15783 on Falcon as well.
Also, when we see queues == 0, ensure we always schedule or rearm
every event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a regression introduced in d3245b28ef
"sfc: Refactor link configuration".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aim of this code was to avoid a spurious XGMII fault over a MAC
reconfigure. It's less relevant now that the PHY reconfigure isn't
called from the MAC reconfigure.
After applying this patch, our link stress test passed 48 hours of
testing without ever resetting the PHY.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'Fatal' errors set an interrupt flag associated with a specific event
queue; only read the syndrome vector if we see that queue's flag set
(legacy interrupts) or in the interrupt handler for that queue (MSI).
Do not ignore an interrupt if the fatal error flag is set but specific
error flags are all zero. Even if we don't schedule a reset, we must
respect the queue mask and rearm the appropriate event queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases failing functions were returning 0 which is obviously wrong.
In other cases they were returning inappropriate error codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena has a separate SRAM bank for each port. On single-port boards
these can be merged together, so each port has an interrupt flag for
parity errors in the other port's SRAM. Currently we do not enable
such merging and should mask this interrupt source.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs specific PHY and board support code for each SFC4000
board; there is no point trying to continue if it is missing.
Currently unsupported boards can trigger an 'oops'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by commit
eb9f6744cb "sfc: Implement ethtool
reset operation".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code would wait indefinitely if MAC stats DMA failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.
Based on a review of the chip datasheets and advice from the designer
of these boards:
- Raise the maximum board temperatures to the specified maximum ambient
temperatures for their PHYs plus the expected temperature bias of the
board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol. It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Commit 357d46a17e "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002. efx_mdio_reset_mmd() returns a positive value rather than 0
on success. The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.
The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash. Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Earlier refactoring has made these inclusions unnecessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, the comment about EVQ_RPTR_REG is based on inconsistent
preliminary hardware documentation, though the following code was
fixed long before release.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings