Add support for all configurable clocks found on NXP LPC32xx SoC.
The list contains several heterogenous groups of clocks:
* system clocks including multiple dividers and muxes,
* x397 PLL, HCLK PLL and USB PLL,
* peripheral clocks inherited from rtc, hclk and pclk,
* USB controller clocks: AHB slave, I2C, OTG, OHCI and device.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The change adds COMMON_CLK_NXP configuration symbol and enables it for
NXP LPC18XX architecture, this is needed to reuse drivers/clk/nxp
folder for NXP common clock framework drivers other than LPC18XX one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
LS2080A is the first implementation of the chassis 3 clockgen, which
has a different register layout than previous chips. It is also little
endian, unlike previous chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
These drivers only have runtime but no build time dependencies so can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the driver and devicetree documentation for the
Silicon Labs SI514 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 100kHz
to 250MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Drop clk.h include, remove some casts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch converts the code to use rational best approximation algorithm which
is much more precise.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Power Interface(SCPI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCPI
protocol.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@baylibre.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: linux-clk@vger.kernel.org
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=I0gO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Having this Kconfig sourced outside the clk menu means the option
is under the "Device Drivers" menu instead of the "Common Clock
Framework" menu. Move it so that the bcm clock config options are
in the right place.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some board designers, when running out of clock output pads, decide to
(mis)use PWM output pads to provide a clock to external components.
This driver supports this practice by providing an adapter between the
PWM and clock bindings in the device tree. As the PWM bindings specify
the period in the device tree, this is a fixed clock.
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Freescale introduced new ARM-based socs which using the compatible
clock IP block with PowerPC-based socs'. So this driver can be used
on both platforms.
Updated relevant descriptions and renamed this driver to better
represent its meaning and keep the function of driver untouched.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The driver allows using CDCE706 in its default configuration recorded in
EEPROM and adjusting of synthesized clocks by consumers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
SRCU is not necessary to be compiled by default in all cases. For tinification
efforts not compiling SRCU unless necessary is desirable.
The current patch tries to make compiling SRCU optional by introducing a new
Kconfig option CONFIG_SRCU which is selected when any of the components making
use of SRCU are selected.
If we do not select CONFIG_SRCU, srcu.o will not be compiled at all.
text data bss dec hex filename
2007 0 0 2007 7d7 kernel/rcu/srcu.o
Size of arch/powerpc/boot/zImage changes from
text data bss dec hex filename
831552 64180 23944 919676 e087c arch/powerpc/boot/zImage : before
829504 64180 23952 917636 e0084 arch/powerpc/boot/zImage : after
so the savings are about ~2000 bytes.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: Josh Triplett <josh@joshtriplett.org>
CC: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: resolve conflict due to removal of arch/ia64/kvm/Kconfig. ]
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
fixes and enhancements to existing drivers as well as new drivers. This
tag contains a bit more arch code than I usually take due to some OMAP2+
changes. Additionally it contains the restart notifier handlers which
are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree I
had to revert one patch and follow up with one more fix near the tip of
this tag. Some dead code is introduced but it will soon become live code
after 3.18-rc1 is released as the rest of the PXA family is converted
over to the common clock framework.
Another trend in this tag is that multiple vendors have started to push
the complexity of changing their CPU frequency into the clock driver,
whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to some
confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=w2rN
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux
Pull clock tree updates from Mike Turquette:
"The clk tree changes for 3.18 are dominated by clock drivers. Mostly
fixes and enhancements to existing drivers as well as new drivers.
This tag contains a bit more arch code than I usually take due to some
OMAP2+ changes. Additionally it contains the restart notifier
handlers which are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree
I had to revert one patch and follow up with one more fix near the tip
of this tag. Some dead code is introduced but it will soon become
live code after 3.18-rc1 is released as the rest of the PXA family is
converted over to the common clock framework.
Another trend in this tag is that multiple vendors have started to
push the complexity of changing their CPU frequency into the clock
driver, whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to
some confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems."
* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
clk: pxa clocks build system fix
Revert "arm: pxa: Transition pxa27x to clk framework"
clk: samsung: register restart handlers for s3c2412 and s3c2443
clk: rockchip: add restart handler
clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
doc/kernel-parameters.txt: clarify clk_ignore_unused
arm: pxa: Transition pxa27x to clk framework
dts: add devicetree bindings for pxa27x clocks
clk: add pxa27x clock drivers
arm: pxa: add clock pll selection bits
clk: dts: document pxa clock binding
clk: add pxa clocks infrastructure
clk: gpio-gate: Ensure gpiod_ APIs are prototyped
clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
clk: ti: LLVMLinux: Move __init outside of type definition
clk: ti: consider the fact that of_clk_get() might return an error
clk: ti: dra7-atl-clock: fix a memory leak
clk: ti: change clock init to use generic of_clk_init
clk: hix5hd2: add I2C clocks
clk: hix5hd2: add watchdog0 clocks
...
This is the initial version of the RK808 PMIC. This is a power management
IC for multimedia products. It provides regulators that are able to
supply power to processor cores and other components. The chip provides
other modules including RTC, Clockout.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Samuel Ortiz <sameo@linux.intel.com> says:
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the building of pxa clock drivers so that the files are actually
compiled if and only if COMMON_CLK was selected by the architecture.
This prevents conflicts with mach-pxa clock legacy implementation.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The MAX77802 PMIC has two 32.768kHz Buffered Clock Outputs with
Low Jitter Mode. This patch adds support for these two clocks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clocks drivers for Maxim PMIC are very similar so they can
be converted to use the generic Maxim clock driver.
Also, while being there use module_platform_driver() helper
macro to eliminate more boilerplate code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxim Integrated Power Management ICs are very similar with
regard to their clock outputs. Most of the clock drivers for
these chips are duplicating code and are simpler enough that
can be converted to use a generic driver to consolidate code
and avoid duplication.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Palmas class of devices can provide 32K clock(s) to be used by other devices
on the board. Depending on the actual device the provided clocks can be:
CLK32K_KG and CLK32K_KGAUDIO
or only one:
CLK32K_KG (TPS659039 for example)
Use separate compatible flags for the two 32K clock.
A system which needs or have only one of the 32k clock from
Palmas will need to add node(s) for each clock as separate section
in the dts file.
The two compatible property is:
"ti,palmas-clk32kg" for clk32kg clock
"ti,palmas-clk32kgaudio" for clk32kgaudio clock
Apart from the register control of the clocks - which is done via
the clock API there is a posibility to enable the external sleep
control. In this way the clock can be enabled/disabled on demand by the
user of the clock.
See the documentation for more details.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
driver additions and fixes. There are additions to the clock core code
for some of the basic types (e.g. the common divider type has some fixes
and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. ba0fae3 in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=2AAL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
This patch adds support for S2MPS14 PMIC clocks (BT and AP) to the
s2mps11 clock driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Move the Kconfig entry for Versatile (& Express) clock drivers
into a separate file and add individual options for sp810
and vexpress_osc drivers, as they are optional in some
configurations and may have separate dependencies.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
This patch adds new Kconfig file for adding new COMMON_CLK_SAMSUNG option.
Samsung platforms can select this for using common clock infrastructure.
CC: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Mostly clock driver updates, more Device Tree support in the form of
common functions useful across platforms and a handful of features and
fixes to the framework core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zk74
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework changes from Mike Turquette:
"The clock framework changes for 3.15 look similar to past pull
requests. Mostly clock driver updates, more Device Tree support in
the form of common functions useful across platforms and a handful of
features and fixes to the framework core"
* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: shmobile: fix setting paretn clock rate
clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
clk: Fix minor errors in of_clk_init() function comments
clk: reverse default clk provider initialization order in of_clk_init()
clk: sirf: update copyright years to 2014
clk: mmp: try to use closer one when do round rate
clk: mmp: fix the wrong calculation formula
clk: mmp: fix wrong mask when calculate denominator
clk: st: Adds quadfs clock binding
clk: st: Adds clockgen-vcc and clockgen-mux clock binding
clk: st: Adds clockgen clock binding
clk: st: Adds divmux and prediv clock binding
clk: st: Support for A9 MUX clocks
clk: st: Support for ClockGenA9/DDR/GPU
clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
clk: st: Support for VCC-mux and MUX clocks
clk: st: Support for PLLs inside ClockGenA(s)
clk: st: Support for DIVMUX and PreDiv Clocks
clk: support hardware-specific debugfs entries
clk: s2mps11: Use of_get_child_by_name
...
Since clock operation within S2MPS11 and S5M8767 are similar, we can
support both the devices within a single driver.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add code for device tree support of clocks in the BCM281xx family of
SoCs. Machines in this family use peripheral clocks implemented by
"Kona" clock control units (CCUs). (Other Broadcom SoC families use
Kona style CCUs as well, but support for them is not yet upstream.)
A BCM281xx SoC has multiple CCUs, each of which manages a set of
clocks on the SoC. A Kona peripheral clock is composite clock that
may include a gate, a parent clock multiplexor, and zero, one
or two dividers. There is a variety of gate types, and many gates
implement hardware-managed gating (often called "auto-gating").
Most dividers divide their input clock signal by an integer value
(one or more). There are also "fractional" dividers which allow
division by non-integer values. To accomodate such dividers,
clock rates and dividers are generally maintained by the code in
"scaled" form, which allows integer and fractional dividers to
be handled in a uniform way.
If present, the gate for a Kona peripheral clock must be enabled
when a change is made to its multiplexor or one of its dividers.
Additionally, dividers and multiplexors have trigger registers which
must be used whenever the divider value or selected parent clock is
changed. The same trigger is often used for a divider and
multiplexor, and a BCM281xx peripheral clock occasionally has two
triggers.
The gate, dividers, and parent clock selector are treated in this
code as "components" of a peripheral clock. Their functionality is
implemented directly--e.g. the common clock framework gate
implementation is not used for a Kona peripheral clock gate. (This
has being considered though, and the intention is to evolve this
code to leverage common code as much as possible.)
The source code is divided into three general portions:
drivers/clk/bcm/clk-kona.h
drivers/clk/bcm/clk-kona.c
These implement the basic Kona clock functionality,
including the clk_ops methods and various routines to
manipulate registers and interpret their values. This
includes some functions used to set clocks to a desired
initial state (though this feature is only partially
implemented here).
drivers/clk/bcm/clk-kona-setup.c
This contains generic run-time initialization code for
data structures representing Kona CCUs and clocks. This
encapsulates the clock structure initialization that can't
be done statically. Note that there is a great deal of
validity-checking code here, making explicit certain
assumptions in the code. This is mostly useful for adding
new clock definitions and could possibly be disabled for
production use.
drivers/clk/bcm/clk-bcm281xx.c
This file defines the specific CCUs used by BCM281XX family
SoCs, as well as the specific clocks implemented by each.
It declares a device tree clock match entry for each CCU
defined.
include/dt-bindings/clock/bcm281xx.h
This file defines the selector (index) values used to
identify a particular clock provided by a CCU. It consists
entirely of C preprocessor constants, to be used by both the
C source and device tree source files.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Populate ${DEBUGS_MOUNT_POINT}/clk if CONFIG_DEBUG_FS is set. This
eliminates the extra (annoying) step of enabling the config option
manually.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Now build the keystone common clock drivers. The build is made
conditional based on COMMON_CLK_KEYSTONE
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk: Add APM X-Gene SoC clock driver for reference, PLL, and device clocks.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Vinayak Kale <vkale@apm.com>
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support to register three(AP/CP/BT) buffered 32.768 KHz
outputs of mfd-s2mps11 with common clock framework.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The new arm64 architecture has no idea of platform or machine, so
it doesn't have to define ARCH_VEXPRESS configuration option at
all. To allow user to select the drivers at all, make it depend
on ARM64 as well.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
With of_clk_provider stubs for CONFIG_OF not set, we can now also enable
clk-si5351 on those architectures.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds the clock driver for Freescale PowerPC corenet
series SoCs using common clock infrastructure.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Calling clk-si5351 driver non-OF ready was too early. This patch
makes clk-si5351 depend on CONFIG_OF again, until things get sorted out.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed spelling of Stephen's name]
This patch adds a common clock driver for Silicon Labs Si5351a/b/c
i2c programmable clock generators. Currently, the driver does not
support VXCO feature of si5351b. Passing platform_data or DT bindings
selectively allows to overwrite stored Si5351 configuration which is
very helpful for clock generators with empty eeprom configuration.
Corresponding device tree binding documentation is also added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This driver adds support for the AXI clkgen pcore to the common clock framework.
The AXI clkgen pcore is a AXI front-end to the MMCM_ADV frequency synthesizer
commonly found in Xilinx FPGAs.
The AXI clkgen pcore is used in Analog Devices' reference designs targeting
Xilinx FPGAs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a branch with updates for Marvell's mvebu/kirkwood platforms. They
came in late-ish, and were heavily interdependent such that it didn't
make sense to split them up across the cross-platform topic branches. So
here they are (for the second release in a row) in a branch on their own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7luC
-----END PGP SIGNATURE-----
Merge tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a DT and non-DT based implementation of
the common clock infrastructure for Versatile Express
platform. It registers (statically or using DT) all
required fixed clocks, initialises motherboard's SP810
cell (that provides clocks for SP804 timers) and
explicitly registers VE "osc" driver, to make the
clock generators available early.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch supports max77686 mfd's clock driver using common clock frame work.
max77686 has 3 clock ouputs which all are generated from crystal oscillator and
SOC can enable/disable them via I2C bus. All clocks are fixed-rate clock sources
so that it doesn't supply interface for changing clock rate.
Driver uses regmap API to communicate with internal register.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There is no choice to have the RealView clocks as module for sure,
so turn this config option into a boolean.
Reported-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the ARM RealView machine over to using the common
clock. The approach is similar to the one used for the Integrator,
and we're reusing the ICST wrapper code.
We have to put the clock intialization in the timer init function
for the clocks to be available when initializing the timer,
keeping them in early_init() is too early for the common clk.
Since we now have to go down and compile drivers/clk/versatile
a CONFIG_COMMON_CLK_VERSATILE symbol has been added so the proper
code gets compiled into the kernel for either machine. A leftover
CLK_VERSATILE in the Integrator Kconfig was fixed up to use
the new symbol as well.
Tested on ARM RealView PB1176.
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
menu "Common Clock Framework" has "depends on COMMON_CLK" and so configs
defined within menu don't require these "depends on COMMON_CLK again".
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The WM831x and WM832x series of PMICs contain a flexible clocking
subsystem intended to provide always on and system core clocks. It
features:
- A 32.768kHz crystal oscillator which can optionally be used to pass
through an externally generated clock.
- A FLL which can be clocked from either the 32.768kHz oscillator or
the CLKIN pin.
- A CLKOUT pin which can bring out either the oscillator or the FLL
output.
- The 32.768kHz clock can also optionally be brought out on the GPIO
pins of the device.
This driver fully supports the 32.768kHz oscillator and CLKOUT. The FLL
is supported only in AUTO mode, the full flexibility of the FLL cannot
currently be used.
Due to a lack of access to systems where the core SoC has been converted
to use the generic clock API this driver has been compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Exposing this option generates confusion and incorrect behavior for
single-image builds across platforms. Enable this behavior permanently.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Using the common clock infrastructure without the common clkdev code makes
little sense, so select CLKDEV_LOOKUP for COMMON_CLK.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
All platforms that use the common clk infrastructure should select
COMMON_CLK from platform code, and on all other platforms, it must
not be enabled, so there is no point making the option visible to
users, and when it is visible, we break randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The common clock framework defines a common struct clk useful across
most platforms as well as an implementation of the clk api that drivers
can use safely for managing clocks.
The net result is consolidation of many different struct clk definitions
and platform-specific clock framework implementations.
This patch introduces the common struct clk, struct clk_ops and an
implementation of the well-known clock api in include/clk/clk.h.
Platforms may define their own hardware-specific clock structure and
their own clock operation callbacks, so long as it wraps an instance of
struct clk_hw.
See Documentation/clk.txt for more details.
This patch is based on the work of Jeremy Kerr, which in turn was based
on the work of Ben Herrenschmidt.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <rob.herring <at> calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Arnd Bergman <arnd.bergmann@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Richard Zhao <richard.zhao@linaro.org>
Cc: Saravana Kannan <skannan@codeaurora.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Deepak Saxena <dsaxena@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The commit 40d3e0f (clk: provide prepare/unprepare functions) provides
the config option HAVE_CLK_PREPARE for platforms that have
prepare/unprepare implementation to select. This patch adds the option
into drivers/clk/Kconfig, so that it can be actually selected.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Vladimir Zapolskiy