Move the UTMI PLL initialization code form clk-tegra<chip>.c files into
clk-pll.c. UTMI PLL was being configured and set in HW control right
after registration. However, when the clock init_table is processed and
child clks of PLLU are enabled, it will call in and enable PLLU as
well, and initiate SW enabling sequence even though PLLU is already in
HW control. This leads to getting UTMIPLL stuck with a SEQ_BUSY status.
Doing the initialization once during pllu_enable means we configure it
properly into HW control.
A side effect of the commonization/localization of the UTMI PLL init
code, is that it corrects some errors that were present for earlier
generations. For instance, in clk-tegra124.c, it used to have:
#define UTMIP_PLL_CFG1_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 6)
when the correct shift to use is present in the new version:
#define UTMIP_PLL_CFG1_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27)
which matches the Tegra124 TRM register definition.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
[rklein: Merged in some later fixes for potential deadlocks]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding: coding style bike-shedding, remove unused variable]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Starting with Tegra124, the mipi-cal clock uses the 72 MHz clock as its
source. On Tegra114 this clock's parent was clk_m, so it is the one-off
chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This flag is a no-op now. Remove usage of the flag.
Acked-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLLM is fixed for Tegra30 up through Tegra114. Starting with Tegra124
PLLM can change rate. Mark PLLM as TEGRA_PLL_FIXED for the generations
where it should be. Modify the check in clk_pll_round_rate() and
clk_pll_recalc_rate() to allow for the non-fixed version to return the
correct rate.
Note that there is no change for Tegra20. This is because PLLM is not
distinguished in that driver, and adding either the PLLM or FIXED_RATE
flags will cause potential problems.
PLLM never supported dynamic ramping. On Tegra20 and Tegra30, there is
no dynamic ramping at all, and on Tegra114, Tegra124 and Tegra132, only
PLLX and PLLC support dynamic ramping, so we can go ahead and remove the
specialized pllm_ops.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This removes the conversion from pdiv to hw, which is already taken
care of by _get_table_rate before this code is run. This avoids
incorrectly converting pdiv to hw twice and getting the wrong hw value.
Also set the input_rate in the freq cfg in _calc_dynamic_ramp_rate while
setting all the other fields.
In order to prevent regressions on earlier SoC generations, all of the
frequency tables need to be updated so that they contain the actual
divider values. If they contain hardware values these would be converted
to hardware values again, yielding the wrong value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: fix regressions on earlier SoC generations]
Signed-off-by: Thierry Reding <treding@nvidia.com>
SoC specific drivers should define the appropriate flags for each
PLL rather than relying on the registration functions to automatically
set flags on their behalf. This will properly allow for changes between
SoC generations where flags might be different and allow sharing the
same logic functions.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use unsigned int for loop variables that can never become negative and
remove a couple of gratuitous blank lines. Also use single spaces around
operators and use a single space instead of a tab to separate comments
from code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OSC_FREQ field of the OSC_CTRL register uses the value 12 for an
oscillator frequency of 26 MHz, not 260 MHz. This isn't really critical
because I don't think boards with such an oscillator have ever existed,
much less been supported upstream.
Signed-off-by: Thierry Reding <treding@nvidia.com>
tegra_audio_clk_init was written expecting a single PLL to be
passed in directly. Change this to accept an array which will
allow for supporting multiple plls and specifying specific data
about them, like their parent, which may change over time.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Only include clk.h in files that are using
it. Also add in a clkdev.h include that was missing in a file
using clkdev APIs.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There is no reason why Tegra114 cannot use the same generic code to set
up the oscillator, clk_m and pll_ref clocks. The only effective change
that this causes is that the CLK_SET_PARENT_RATE flag is dropped, but
since these clocks are all fixed it is not needed anyway.
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
The memory controller clock runs either at half or the same frequency as
the EMC clock.
Reviewed-By: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
vi_sensor and vi_sensor2 have a wrong hw clkid on Tegra124. Fix this by
correcting the hw clkid for Tegra124 and creating the Tegra114 vi_sensor clock
from its own data. Tegra124 was also using the wrong internal clock id.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Initialize the XUSB-related clocks with appropriate parents and rates
for both Tegra114 and Tegra124.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently the Tegra1x4 clock init code hard-codes the mux setting
for xusb_hs_src and treats it as a fixed-factor clock. It is,
however, a mux which can be parented by either xusb_ss_src/2 or
pll_u_60M. Add the fixed-factor clock xusb_ss_div2 and put an
entry in periph_clks[] for the xusb_hs_src mux.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The sdmmc clocks on Tegra114 and Tegra124 are 3-bit wide muxes with
6 parents. Add support for tegra_clk_sdmmc*_8 and switch Tegra114
and Tegra124 to use these clocks instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The Tegra CAR module implements both a clock and reset controller. So
far, the driver exposes the clock feature via the common clock API and
the reset feature using a custom API. This patch adds an implementation
of the common reset framework API (include/linux/reset*.h). The legacy
reset implementation will be removed once all drivers have been
converted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
The low-power DSI clocks are used during host-driven transactions on the
DSI bus. Documentation recommends that they be children of PLLP and run
at a frequency of at least 52 MHz.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add disp1 and disp2 clocks to the clock initialization table. These
clocks are required for display and HDMI support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Introduce a common function which performs super clock initialization for
Tegra114 and beyond.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce new files for fixed and PMC clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a new file for peripheral clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure. Also PLLP and the PLLP_OUT
clocks will be initialized here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move audio clocks and PLLA initialization to a common file so it can be used by
multiple Tegra SoCs. Also a new array tegra114_clks is introduced for Tegra114
which specifies which common clocks are available on Tegra114 and what their
DT IDs are.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Add a common infra for registering clkdev. This allows decoupling clk
registration from clkdev registration.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move some fields related to the PLL HW description to the tegra_clk_pll_params.
This allows some PLL code to be moved to common files later.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Use pll_ref instead of pll_re_vco as the pll_e parent on Tegra114. Also
add a 12Mhz pll_ref table entry for pll_e for Tegra114. This prevents
the system from crashing at bootup because of an unsupported pll_re_vco
rate.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
VCO min clipping, dynamic ramp setup and IDDQ init can be done in the
respective PLL clk_register functions if the parent is already registered.
This is done for other some PLLs already.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch makes periph_clk_enb_refcnt a global array, dynamically allocated
at boottime. It simplifies the macros somewhat and allows clocks common to
several Tegra SoCs to be defined in a separate files. Also the clks array
becomes global and dynamically allocated which allows the DT registration to
be moved to a generic funcion.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch determines the register bank for clock enable/disable and reset
based on the clock ID instead of hardcoding it in the tables describing the
clocks. This results in less data to be maintained in the tables, making the
code easier to understand. The full benefit of the change will be realized once
also other clocktypes will be table based.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The power-on default parent for this clock is pll_m, which turns out to
be wrong. Previously, bootloader reparented this clock. We'll do it in
the kernel as well, so that there's one less thing that we depend on
bootloader to initialize.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Perform upwards rounding when calculating dividers for periph clks on Tegra30
and Tegra114.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
pll_m will be the parent of gr2d/gr3d if we don't do this.
And because pll_m runs at a high rate so gr2d/gr3d will be
unstable. So change the parent of them to pll_c2.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
In Tegra114, vde/gr_2d/gr_3d have 3 bits for clock source selection.
So change the clock init macro for these clocks from
"TEGRA_INIT_DATA_INT" to "TEGRA_INIT_DATA_INT8".
Besides, no one uses "TEGRA_INIT_DATA_INT" after this change, so
remove this macro.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra114 sbc1-sbc6 have more possible parent clocks than Tegra30.
So correct the parents and mux width for them.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
As the clock IDs are now specified in a header file, we can use those
definitions instead of maintaining an internal enum.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
Add a CLK_SET_RATE_NO_REPARENT clock flag, which will prevent muxes
being reparented during clk_set_rate.
To avoid breaking existing platforms, all callers of clk_register_mux()
are adjusted to pass the new flag. Platform maintainers are encouraged
to remove the flag if they wish to allow mux reparenting on set_rate.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Chao Xie <xiechao.mail@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spear-devel@list.st.com
Cc: linux-tegra@vger.kernel.org
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com> [tegra]
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [sunxi]
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com> [Zynq]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
across several different platforms and architectures, fixes to existing
drivers, a MAINTAINERS file fix and improvements to the basic clock
types that allow them to be of use to more platforms than before. Only a
few fixes to the core framework are included with most all of the
changes landing in the various clock drivers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SwMB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux
Pull clock framework updates from Mike Turquette:
"The common clock framework changes for 3.11 include new clock drivers
across several different platforms and architectures, fixes to
existing drivers, a MAINTAINERS file fix and improvements to the basic
clock types that allow them to be of use to more platforms than before.
Only a few fixes to the core framework are included with most all of
the changes landing in the various clock drivers themselves."
* tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux: (55 commits)
clk: tegra: fix ifdef for tegra_periph_reset_assert inline
clk: tegra: provide tegra_periph_reset_assert alternative
clk: exynos4: Fix clock aliases for cpufreq related clocks
clk: samsung: Add MUX_FA macro to pass flag and alias
clk: add support for Rockchip gate clocks
clk: vexpress: Make the clock drivers directly available for arm64
clk: vexpress: Use full node name to identify individual clocks
clk: tegra: T114: add DFLL DVCO reset control
clk: tegra: T114: add DFLL source clocks
clk: tegra: T114: add FCPU clock shaper programming, needed by the DFLL
clk: gate: add CLK_GATE_HIWORD_MASK
clk: divider: add CLK_DIVIDER_HIWORD_MASK flag
clk: mux: add CLK_MUX_HIWORD_MASK
clk: Always notify whole subtree when reparenting
MAINTAINERS: make drivers/clk entry match subdirs
clk: honor CLK_GET_RATE_NOCACHE in clk_set_rate
clk: use clk_get_rate() for debugfs
clk: tegra: Use override bits when needed
clk: tegra: override bits for Tegra30 PLLM
clk: tegra: override bits for Tegra114 PLLM
...
Add DFLL DVCO reset line control functions to the CAR IP block driver.
The DVCO present in the DFLL IP block has a separate reset line,
exposed via the CAR IP block. This reset line is asserted upon SoC
reset. Unless something (such as the DFLL driver) deasserts this
line, the DVCO will not oscillate, although reads and writes to the
DFLL IP block will complete.
Thanks to Aleksandr Frid <afrid@nvidia.com> for identifying this and
saving hours of debugging time.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add the input clocks needed by the DFLL IP blocks. Initialize them to
51MHz (as required by the DFLL GFD) and to use the PLL_P clock source.
This patch is a collaboration with Peter De Schrijver
<pdeschrijver@nvidia.com>.
Thanks to Laxman Dewangan <ldewangan@nvidia.com> for identifying the
requirement to keep the DFLL clocks enabled to resolve PWR_I2C timeout
issues.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add clock functions to initialize, enable, and disable the FCPU clock
shapers, based on the FCPU voltage rail state. These will be used by
the DFLL clocksource driver code.
This version of the patch contains a fix for a problem noticed by Andrew
Chew <achew@nvidia.com>, where some of the FINETRIM_R bitfields were
incorrectly defined.
Based on code originally written by Aleksandr Frid <afrid@nvidia.com>.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Andrew Chew <achew@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Andrew Bresticker