This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead. This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently. Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing. Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround. Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters. These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions). New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82571 and 82572 Errata #13 documents that the Si feature DMA Dynamic
Clock Gating should be disabled, and identifies the workaround of
disabling the feature by EEPROM setting. EEPROM versions that do not
include the recommended workaround have been found in the field, and so
some customers remain at risk. Because the feature DMA Dynamic clock
Gating can be disabled by directly setting the appropriate bit in the
E1000_CTRL_EXT register, this patch overrides the EEPROM setting, and
force-disables the feature.
Signed-off-by: dave graham <david.graham@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.
For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set). If invalid, it would have defaulted to the
possibly invalid bank 0. Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.
[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables ECC correction for the packet buffer on all 82571
silicon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new part has the same feature set as previous parts with the addition
of MSI-X support.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for new LOM devices on the latest generation ICHx platforms.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some systems do not like 82571/2 use of 16-bit MSI messages and some
other systems claim to support MSI, but neither really works. Setup a
test MSI handler to detect whether or not MSI is working properly, and
if not, fallback to legacy INTx interrupts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.
This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).
To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several components to this complex fix. The es2lan cards occasionally
gave a "HW Error" especially when forcing speed. Some users also
reported that the BMC stole ARP packets.
The fixes include setting the proper SW_FW bits to tell the BMC
that we're active and not do any un-initialization at all, so the
setup routine is largely changed.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several stats registers are completely unused and we just waste pci
bus time reading them. We also omit using the high 32 bits of the GORC/
GOTC counters. We can just read clear them and only read the low registers.
Mii-tool can also break es2lan if it executes a MII PHY register
ioctl while the device is in autonegotiation. Unfortunately it seems
that several applications and installations still perform this ioctl
call periodically and especially in this crucial startup time. We
can fool the ioctl by providing fail safe information that mimics
the "down" link state and only perform the dangerous PHY reads once
after link comes up to fill in the real values. As long as link
stays up the information will not change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adjusting the comment blocks here to be code-style compliant. no
code changes.
Changed some copyright dates to 2008.
Indentation fixes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ethtool supports wake-on-ARP and wake-on-link, and so does the hardware
supported by e1000e. This patch just introduces the two.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan