[USB]Add Samsung SGH-I500/Android modem ID switch to visor driver
Samsung decided to reuse USB ID of its old CDMA phone SGH-I500 for the
modem part of some of their Android phones. At least Galaxy Spica
is affected.
This modem needs ACM driver and does not work with visor driver which
binds the conflicting ID for SGH-I500.
Because SGH-I500 is pretty an old hardware its best to add switch to
visor
driver in cause somebody still wants to use that phone with Linux.
Note that this is needed only when using the Android phone as modem,
not in USB storage or ADB mode.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added mct_u232_ioctl (implements TIOCMIWAIT command),
mct_u232_get_icount (implements TIOCGICOUNT command) and
mct_u232_msr_to_icount functions. MCT U232 P9 is one of a few usb to
serail adapters which converts USB +/-5v voltage levels to COM +/-15
voltages. So it can also power COM interfaced devices. This makes it
very usable for legacy COM interfaced data-acquisition hardware. I
tested new implementation with AWARE Electronics RM-60 radiation meter,
which sends pulse via RNG COM line whenever new particle is registered.
Signed-off-by: Vadim Tsozik <tsozik@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB Vendor ID and Product ID for a Acton Research Corp.
spectrograph device with a FTDI chip for serial I/O.
Signed-off-by: Michael H Williamson <michael.h.williamson@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
on ST Micro Connect Lite we have 4 port
Part A and B for the JTAG
Port C Uart
Port D for PIO
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
Cc: stable@kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 2232H high speed baud rates also support fractional baud
rate divisors, but when the performing the divisions before
the multiplication, the fractional bits are lost.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Acked-by: Mark Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan's commit 335f8514f2 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found the original patch on the db0fhn repeater wiki (couldn't find the email
of the origial author) I guess it was never commited.
I updated and added some Icom HAM-radio devices to the ftdi driver.
Added extra comments to make clear what devices it are.
Signed-off-by: Pieter Maes <maescool@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added 0x0307 device id to support Motorola cables to the pl2303 usb
serial driver. This cable has a modified chip that is a pl2303, but
declares itself as 0307. Fixed by adding the right device id to the
supported devices list, assigning it the code labeled
PL2303_PRODUCT_ID_MOTOROLA.
Signed-off-by: Dario Lombardo <dario.lombardo@libero.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/drivers/usb/serial/option.c: Adding support for Cinterion's HC25, HC28,
HC28J, EU3-E, EU3-P and PH8 by correcting/adding Cinterion's and
Siemens' Vendor IDs as well as Product IDs and USB_DEVICE tuples
Signed-off-by: Nicolaus Colberg <nicolaus.colberg@cinterion.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1443) fixes a bug found in many of the USB serial
drivers: They don't set the .usb_driver field in their
usb_serial_driver structure. This field is needed for assigning
dynamic IDs for device matching.
In addition, starting with the 2.6.37 kernel, the .usb_driver field is
needed for proper autosuspend operation. Without it, attempts to open
the device file will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Williams <dcbw@redhat.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device ID removed 0x10C4/0x8149 for West Mountain Radio Computerized
Battery Analyzer. This device is actually based on a SiLabs C8051Fxxx,
see http://www.etheus.net/SiUSBXp_Linux_Driver for further info.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another CDC-ACM + vendor specific interface layout for the QCDM port.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
flush_scheduled_work() is being deprecated. Directly flush or cancel
work items instead.
* u_ether, isp1301_omap, speedtch conversions are straight-forward.
* ochi-hcd should only flush when quirk_nec() is true as otherwise the
work wouldn't have been initialized.
* In oti6858, cancel_delayed_work() + flush_scheduled_work() ->
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Willem-Jan noticed that the ftdi_sio driver did not support the
TIOCSERGETLSR ioctl, and some userspace programs rely on it. This patch
adds the support.
Reported-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Tested-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
This patch fixes a build failure[1] by adding the missing uaccess.h needed
for copy_from_user and copy_to_user
References:
http://kisskb.ellerman.id.au/kisskb/buildresult/3607218/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was done to handle a number of conflicts in the batman-adv
and winbond drivers properly. It also now allows us to fix up the sysfs
attributes properly that were not in the .37 release due to them being
only in this tree at the time.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices (ex ZTE 2726) simply don't respond at all when data is sent
to some of their USB interfaces. The data gets stuck in the TTYs queue
and sits there until close(2), which them blocks because closing_wait
defaults to 30 seconds (even though the fd is O_NONBLOCK). This is
rarely desired. Implement the standard mechanism to adjust closing_wait
and let applications handle it how they want to.
Signed-off-by: Dan Williams <dcbw@redhat.com>
This patch (as1437) fixes a bug in the usb-serial autosuspend
handling. Since the usb-serial core now has autosuspend support, it
must set the .supports_autosuspend member in every serial driver it
registers. Otherwise the usb_autopm_get_interface() call won't work.
This fixes Bugzilla #23012.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@kernel.org
Reported-by: Kevin Smith <thirdwiggin@gmail.com>
Reported-and-tested-by: Simon Gerber <gesimu@gmail.com>
Reported-and-tested-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485
converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001.
This should also work with the stable branches for:
2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36
Signed-off-by: Jacques Viviers <jacques.viviers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another variant of the RT Systems programming cable for ham radios.
Signed-off-by: Michael Stuermer <ms@mallorn.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was necessary in order to resolve some conflicts that happened
between -rc1 and -rc2 with the following files:
drivers/staging/bcm/Bcmchar.c
drivers/staging/intel_sst/intel_sst_app_interface.c
All should be resolved now.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When huawei datacard with PID 0x14AC is insterted into Linux system, the
present kernel will load the "option" driver to all the interfaces. But
actually, some interfaces run as other function and do not need "option"
driver.
In this path, we modify the id_tables, when the PID is 0x14ac ,VID is
0x12d1, Only when the interface's Class is 0xff,Subclass is 0xff, Pro is
0xff, it does need "option" driver.
Signed-off-by: ma rui <m00150988@huawei.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The max_packet_size logic is taken from ftdi_sio, but it's not needed
for this device. This also makes proces_read_urb simpler.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs for the Milkymist One FTDI-based JTAG/serial adapter
(http://projects.qi-hardware.com/index.php/p/mmone-jtag-serial-cable/)
to the ftdi_sio driver and disable the first serial channel (used as
JTAG from userspace).
Signed-off-by: Sebastien Bourdeauducq <sebastien@milkymist.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
Fix regression introduced by commit
f26788da3b (USB: serial: refactor generic
close) which broke driver close().
This driver uses non-standard semantics for the read urb which makes the
generic close function fail to kill it (the read urb is actually an
interrupt urb and therefore bulk_in size is zero).
Reported-by: Eric Shattow "Eprecocious" <lucent@gmail.com>
Tested-by: Eric Shattow "Eprecocious" <lucent@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the requested device ids to the ftdi_sio driver.
Reported-by: Ewan Bingham <ewan@auc.co.uk>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OPN2001 expects write operations to arrive as a vendor-specific command
through the control pipe (instead of using a separate bulk-out pipe).
Signed-off-by: Alon Ziv <alon-git@nolaviz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bulk-read callback had two bugs:
a) The bulk-in packet's leading two zeros were returned (and the two last
bytes truncated)
b) The wrong URB was transmitted for the second (and later) read requests,
causing further reads to return the entire packet (including leading
zeros)
Signed-off-by: Alon Ziv <alon-git@nolaviz.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to set latency timeout at every open.
This also fixes an issue with the read latency being as high as 250ms
(instead of 1ms) for the first read after port probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression introduced by commit
214916f2ec (USB: visor: reimplement using
generic framework) which broke initialisation of UX50/TH55 devices that
used re-mapped bulk-out endpoint addresses.
Reported-by: Robert Gadsdon <rgadsdon@bayarea.net>
Tested-by: Robert Gadsdon <rgadsdon@bayarea.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for FTDI USB serial driver ads new VID/PIDs used on various
devices manufactured by Papouch (http://www.papouch.com). These devices
have their own VID/PID, although they're using standard FTDI chip. In
ftdi_sio.c, I also made small cleanup to have declarations for all
Papouch devices together.
Signed-off-by: Daniel Suchy <danny@danysek.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment while trying to
maintain the original scheme in each file.
None of the dependencies are modified.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OpenDCC project is developing a new hardware. This patch adds its
PID to the list of known FTDI devices. The PID can be found at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch to qcserial.c enables the Diagnostics Monitor
and NMEA GPS ports on Qualcomm Gobi 2000 devices.
A Gobi 2000 device will provide 3 serial ports:
# /dev/ttyUSB0 -> Diagnostics
# /dev/ttyUSB1 -> 3G Modem
# /dev/ttyUSB2 -> NMEA GPS port
* The Diagnostics Monitor uses Qualcomm's DM protocol; I used
libqcdm (ModemManager) to talk to it, found it working, but at
least DM commands 12 and 64 are not implemented on my device
(Gobi 2000 built into Thinkpad x100e).
* Functionality of the 3G Modem port remains unchanged.
* The GPS port and how to enable it has been confirmed now in the
Gobi 3000 source code at:
https://www.codeaurora.org/patches/quic/gobi/
Enable/disable GPS via:
echo "\$GPS_START" > /dev/ttyUSB2
# use GPS
echo "\$GPS_STOP" > /dev/ttyUSB2
Signed-off-by: Matthias G. Eckermann <mge@arcor.de>
This reverts commit 6a1a82df91.
RTS and DTR should not be modified based on CRTSCTS when calling
set_termios.
Modem control lines are raised at port open by the tty layer and should stay
raised regardless of whether hardware flow control is enabled or not.
This is in conformance with the way serial ports work today and many
applications depend on this behaviour to be able to talk to hardware
implementing hardware flow control (without the applications actually using
it).
Hardware which expects different behaviour on these lines can always
use TIOCMSET/TIOCMBI[SC] after port open to change them.
Reported-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Dave Mielke <dave@mielke.cc>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, adds to the option driver the Onda Communication
(http://www.ondacommunication.com) vendor id, and the MT825UP modem
device id.
Note that many variants of this same device are being release here in
Italy (at least one or two per telephony operator).
These devices are perfectly equivalent except for some predefined
settings (which can be changed of course).
It should be noted that most ONDA devices are allready supported (they
used other vendor's ids in the past). The patch seems working fine here,
and the rest of the driver seems uninfluenced.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for Accesio USB to Serial adapters, which are built around
FTDI FT232 UARTs. Tested with the Accesio USB-COM-4SM.
Signed-off-by: Rich Mattes <richmattes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are lots of ZTE USB id's currently not covered by usb/serial. Adds them,
to allow those devices to work properly on Linux.
While here, put the USB ID's for 0x2002/0x2003 at the sorted order.
This patch is based on zte.c file found on MF645.
PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented,
an USB ID for 0x0026.
Not sure why, but I think that 0053 is used by their devices in storage mode only.
So, I opted to keep the comment on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new driver to access the SAM-BA boot application of Atmel AT91SAM
devices.
The SAM-BA firmware cannot handle merged write requests so we cannot use
the generic write implementation (which uses the port write fifo).
Tested with the SAM-BA 2.10 tools and an Atmel at91sam9260-ek.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simple pasting job using the new ops function. Also fix a couple of devices
directly returning the internal struct (which happens at this point to match
for the fields that matter but isn't correct or futureproof)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Rosenberg noted that various drivers return the struct with uncleared
fields. Instead of spending forever trying to stomp all the drivers that
get it wrong (and every new driver) do the job in one place.
This first patch adds the needed operations and hooks them up, including
the needed USB midlayer and serial core plumbing.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe000 T-Com TC 300
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 TC 300
iSerial 3 0001
[snip]
---------------------------------------------------------------------------
However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe003 Pirelli DP-L10
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 DP-L10
iSerial 3 0001
[snip]
-------------------------------------------------------------------------
All that is required is an extra USB_DEVICE entry:
{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */
The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the ID for the Ionics PlugComputer (<http://ionicsplug.com/>).
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flag was never set in ssu100_process_packet. Add logic to set it
before calling tty_insert_flip_*
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a disconnect function to the functions of this device. The
disconnect is a call to usb_serial_generic_disconnect() so it requires
that symbol to be exported from generic.c.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed by the ssu100 driver to use this function.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the logic for TIOCMIWAIT to use wait_event_interruptible.
This also adds support for TIOCGICOUNT.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function ssu100_setregister was hard coded to only set the MCR
register. Add a register parameter so that other registers can be
set.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ssu100 uses a TI16C550C UART so the SERIAL_ defines in this code
are duplicates of those found in serial_reg.h. Remove the defines in
ssu100.c and use the ones in the header file.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status information does not appear at the start of each incoming
packet so the check for len < 4 at the start of ssu100_process_packet
is wrong. Remove it.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we can't read the firmware for a device from the disk, and yet the
device already has a valid firmware image in it, we don't want to
replace the firmware with something invalid. So check the version
number to be less than the current one to verify this is the correct
thing to do.
Reported-by: Chris Beauchamp <chris@chillibean.tv>
Tested-by: Chris Beauchamp <chris@chillibean.tv>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB max packet size (always little-endian) was not being byte
swapped on big-endian systems.
Applicable since [USB: ftdi_sio: fix hi-speed device packet size calculation] approx 2.6.31
Signed-off-by: Michael Wileczka <mikewileczka@yahoo.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The definitions for BREAK_ON and BREAK_OFF are inverted, causing break
requests to fail. This patch sets BREAK_ON and BREAK_OFF to the correct
values.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Zeagle N2iTiON3 dive computer interface. Since
Zeagle devices are actually manufactured by Seiko, this patch will
support other Seiko based models as well.
Signed-off-by: Jef Driesen <jefdriesen@telenet.be>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch with title below makes reference count of usb serial module
always more than one after driver is bound.
USB-BKL: Remove BKL use for usb serial driver probing
In fact, the patch above only replaces lock_kernel() with try_module_get()
, and does not use module_put() to do what unlock_kernel() did, so casue leak
of reference count of usb serial module and the module can not be unloaded
after serial driver is bound with device.
This patch fixes the issue, also simplifies such things:
-only call try_module_get() once in the entry of usb_serial_probe()
-only call module_put() once in the exit of usb_serial_probe
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently bought a i-gotU USB GPS, and whilst hunting around for linux
support discovered this post by you back in 2009:
http://kerneltrap.org/mailarchive/linux-usb/2009/3/12/5148644
>Try the navman driver instead. You can either add the device id to the
> driver and rebuild it, or do this before you plug the device in:
> modprobe navman
> echo -n "0x0df7 0x0900" > /sys/bus/usb-serial/drivers/navman/new_id
>
> and then plug your device in and see if that works.
I can confirm that the navman driver works with the right device IDs on
my i-gotU GT-600, which has the same device IDs. Attached is a patch
adding the IDs.
From: Ross Burton <ross@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysrq operations do not accept tty argument anymore so no need to pass
it to us.
[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
caused by sysrq using bool but not including linux/types.h]
[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
driver]
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As David VomLehn points out, it was possible to receive an interrupt
before clearing the free-urb flag which could lead to the urb being
incorrectly marked as busy.
For the same reason, move tx_bytes accounting so that it will never be
negative.
Note that the free-flags set and clear operations do not need any
additional locking as they are manipulated while USB_SERIAL_WRITE_BUSY
is set.
Reported-by: David VomLehn <dvomlehn@cisco.com>
Tested-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Quatech SSU-100 single port usb to serial device.
This driver is based on the ftdi_sio.c driver and the original
serqt_usb driver from Quatech.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to add a US Interface, Inc. "Navigator" USB device.
Specifically, it's a HAM Radio USB sound modem that also
incorporates three pairs of unique FTDI serial ports. The standard
Linux FTDI serial driver will only recognize the first two serial
ports of an unknown FDTI derived device and this patch adds in
recognition to these specific new IDs.
Signed-off-by: David A. Ranch <dranch@trinnet.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product IDs of Huawei's K3765 and K4505 mobile
broadband usb modems to option.c. It also adds a quirk to the option
probe function so that binding to the device's network interface(class
0xff) is avoided. This is necessary to allow another driver to bind to
that, and to avoid programs like wvdial opening a nonfunctioning tty
during modem discovery.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will
enable support for the Segway Robotic Mobility Platform (RMP200) in the
ftdi_sio kernel module. Currently, users of the Segway RMP200 must use
a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a
udev rule to get the ftdi_sio module to handle the usb interface and
mount it on /dev/ttyXXX. This is not a good solution because some users
will have multiple USB to Serial converters which will use the ftdi_sio
module.
Signed-off-by: John Rogers <jgrogers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds Huawei ETS 1220 product id into the list of supported
devices in 'option' usb serial driver.
Signed-off-by: Pavel Kazlou <p.i.kazlou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Usb serial port device is child of its usb interface device, so
we can enable async suspend of usb serial port device to speedup
system suspend.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb serial driver initialization tried to use the BKL to stop
driver modules from unloading, but that didn't work anyways.
There was already some code to do proper try_module_get,
but it was conditional on having a new probe interface.
I checked all the low level drivers and they all have proper
.owner = THIS_MODULE, so it's ok to always use.
The other problem was the usb_serial_driver_list needing
protection by a lock. This was broken anyways because unregister
did not necessarily have the BKL.
I extended the extending table_lock mutex to protect this case too.
With these changes the BKL can be removed here.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ipaq already had this device id defined:
{ USB_DEVICE(0x0BB4, 0x00CF) }, /* HTC USB Modem */
Revert the commit which adds the duplicate entry.
This reverts commit 04cab13293.
Originally-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AMOI_VENDOR_ID is defined twice. Remove the duplicate entry and move
the AMOI_PRODUCT_9508 definition to be grouped with the other AMOI
product definitions.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This now refcounts but doesn't actually check the reference was obtained in
all the places it should.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
RT Systems has put out bunch of ham radio cables based on the FT232RL
chip. Each cable type has a unique PID, this adds one for the Yaesu VX-7
radios.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbserial: Add AMOI Skypephone S2 support.
This patch adds support for the AMOI Skypephone S2 to the usbserial module.
Tested-by: Dennis Jansen <Dennis.Jansen@web.de>
Signed-off-by: Dennis Jansen <Dennis.Jansen@web.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the Generic Qualcomm Gobi 2000 WWAN UMTS/CDMA modem
Signed-off-by: Andrew Bird <ajb@spheresytems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: support for Signalyzer tools based on FTDI chips
This patch adds support for the Xverve Signalyzers.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add VID/PID for Sierra Wireless 250U USB dongle to sierra.c
Allows use of 3G radio only
Signed-off-by: August Huber <gus@pbx.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds missing kfree(data) before return -ENODEV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.
I believe the merge problem occurred with the commit:
dee5658b48
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If port is NULL, then the call to dev_err will dereference a value that is
a small offset from NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Length field of header was incorrectly set to available payload space
rather than the actual payload size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static per-port,
singleton(!) urb pool).
Also remove changelog header (can be retrieved through git).
Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Private data was not freed on error path in startup.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up read processing logic.
Tested using a cp210x device in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom single-urb write implementation.
Note that this driver still depended on the write callback from the old
generic framework.
Tested against original read processing using a cp210x device in a
loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill private write fifo and use port fifo instead (protected under
port lock).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Use private write fifo to minimise changes to lock handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Note that cypress_m8 has no port write fifo as it has no bulk-out
endpoint.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use bulk_out_size in usb_serial_driver to set urb buffer size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size to avoid any regression in throughput
after replacing the old writing scheme which used dynamic buffers (e.g.
up to 2k).
256b has been determined to be a good choice for several drivers
including ftdi_sio which used to have a more or less identical write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use process_read_urb to implement line status handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (dynamically allocated write
urbs).
Note that I chose to remove the stat module parameter which was supposed
to keep count of the amount of data sent and received, but which has
been broken for three years (since b308e74d9c
"USB: visor driver adapted to new tty buffering" -- bytes_in was
incorrectly updated and was thus always reported as 0).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix memory leak for some devices (Sony Clie 3.5) due to port private
data not being freed on release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo, read and write implementations (single-urb and fifo,
but still maintained list of 256*256b urb buffers per port).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static 16*4k write-urb pool
shared among all ports in system).
Also remove old changelog entries in header (code is now gone, and
these entries can still be retrieved through git).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maciej Szmigiero