1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CgqW
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
* tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (217 commits)
cpufreq: Don't use smp_processor_id() in preemptible context
cpuidle: coupled: fix race condition between pokes and safe state
cpuidle: coupled: abort idle if pokes are pending
cpuidle: coupled: disable interrupts after entering safe state
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
cpufreq: governor: Fix typos in comments
cpufreq: governors: Remove duplicate check of target freq in supported range
cpufreq: Fix timer/workqueue corruption due to double queueing
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
cpufreq: imx6q: Fix clock enable balance
ACPI: blacklist win8 OSI for buggy laptops
cpufreq: tegra: fix the wrong clock name
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
...
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
This reworks kvmppc_mmu_book3s_64_xlate() to make it check the large
page bit in the hashed page table entries (HPTEs) it looks at, and
to simplify and streamline the code. The checking of the first dword
of each HPTE is now done with a single mask and compare operation,
and all the code dealing with the matching HPTE, if we find one,
is consolidated in one place in the main line of the function flow.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Most architectures use the same implementation. Collapse the common ones
into a single weak function that can be overridden.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
It turns out that if we exit the guest due to a hcall instruction (sc 1),
and the loading of the instruction in the guest exit path fails for any
reason, the call to kvmppc_ld() in kvmppc_get_last_inst() fetches the
instruction after the hcall instruction rather than the hcall itself.
This in turn means that the instruction doesn't get recognized as an
hcall in kvmppc_handle_exit_pr() but gets passed to the guest kernel
as a sc instruction. That usually results in the guest kernel getting
a return code of 38 (ENOSYS) from an hcall, which often triggers a
BUG_ON() or other failure.
This fixes the problem by adding a new variant of kvmppc_get_last_inst()
called kvmppc_get_last_sc(), which fetches the instruction if necessary
from pc - 4 rather than pc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the code assumes that once we load up guest FP/VSX or VMX
state into the CPU, it stays valid in the CPU registers until we
explicitly flush it to the thread_struct. However, on POWER7,
copy_page() and memcpy() can use VMX. These functions do flush the
VMX state to the thread_struct before using VMX instructions, but if
this happens while we have guest state in the VMX registers, and we
then re-enter the guest, we don't reload the VMX state from the
thread_struct, leading to guest corruption. This has been observed
to cause guest processes to segfault.
To fix this, we check before re-entering the guest that all of the
bits corresponding to facilities owned by the guest, as expressed
in vcpu->arch.guest_owned_ext, are set in current->thread.regs->msr.
Any bits that have been cleared correspond to facilities that have
been used by kernel code and thus flushed to the thread_struct, so
for them we reload the state from the thread_struct.
We also need to check current->thread.regs->msr before calling
giveup_fpu() or giveup_altivec(), since if the relevant bit is
clear, the state has already been flushed to the thread_struct and
to flush it again would corrupt it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 8e44ddc3f3 ("powerpc/kvm/book3s: Add support for H_IPOLL and
H_XIRR_X in XICS emulation") added a call to get_tb() but didn't
include the header that defines it, and on some configs this means
book3s_xics.c fails to compile:
arch/powerpc/kvm/book3s_xics.c: In function ‘kvmppc_xics_hcall’:
arch/powerpc/kvm/book3s_xics.c:812:3: error: implicit declaration of function ‘get_tb’ [-Werror=implicit-function-declaration]
Cc: stable@vger.kernel.org [v3.10, v3.11]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
err was overwritten by a previous function call, and checked to be 0. If
the following page allocation fails, 0 is going to be returned instead
of -ENOMEM.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
'rmls' is 'unsigned long', lpcr_rmls() will return negative number when
failure occurs, so it need a type cast for comparing.
'lpid' is 'unsigned long', kvmppc_alloc_lpid() return negative number
when failure occurs, so it need a type cast for comparing.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This file is entirely pseries specific nowadays, so move it out
of arch/powerpc/kernel where it doesn't belong anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With OPAL v3 we can return secondary CPUs to firmware on kexec. This
allows firmware to do various cleanups making things generally more
reliable, and will enable the "new" kernel to call OPAL to perform
some reconfiguration tasks early on that can only be done while
all the CPUs are in firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of
gcc as something like:
addis 3,2,.LANCHOR1+4611686018427387904@toc@ha
addi 3,3,.LANCHOR1+4611686018427387904@toc@l
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As suggested by paulus we can simplify the Data Stream Control Register
(DSCR) Facility Status and Control Register (FSCR) handling.
Firstly, we simplify the asm by using a rldimi.
Secondly, we now use the FSCR only to control the DSCR facility, rather
than both the FSCR and HFSCR. Users will see no functional change from
this but will get a minor speedup as they will trap into the kernel only
once (rather than twice) when they first touch the DSCR. Also, this
changes removes a bunch of ugly FTR_SECTION code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Calls to dlpar_detach_node do not iterate over child nodes detaching them as
well. By iterating and detaching the child nodes we ensure that they have the
OF_DETACHED flag set and that their reference counts are decremented such that
the node will be freed from memory by of_node_release.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The node to be detached is retrieved via its phandle by a call to
of_find_node_by_phandle which increments the ref count. We need a matching
call to of_node_put to decrement the ref count and ensure the node is
actually freed.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the device nodes created in the device subtree returned by a call to
dlpar_configure_connector are all named in the root node. This is because the
the node name in the work area returned by ibm,configure-connector rtas call
only contains the node name and not the entire node path. Passing the parent
node where the new subtree will be created to dlpar_configure_connector allows
the correct node path to be prefixed in the full_name field.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the OF_DYNAMIC and kref initialization for a node happens in
dlpar_attach_node. However, a node passed to dlpar_attach_node may be a tree
containing child nodes, and no initialization traversal is done on the
tree. Since the children never get their kref initialized or the OF_DYNAMIC
flag set these nodes are prevented from ever being released from memory
should they become detached. This initialization step is better done at the
time each node is allocated in dlpar_parse_cc_node.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On the first call to ibm,update-properties for a node the first property
returned is the full node path. Currently this is not parsed correctly by the
update_dt_node function. Commit 2e9b7b0 attempted to fix this, but was
incorrect as it made a wrong assumption about the layout of the first
property in the work area. Further, if ibm,update-properties must be called
multiple times for the same node this special property should only be skipped
after the initial call. The first property descriptor returned consists of
the property name, property value length, and property value. The property
name is an empty string, property length is encoded in 4 byte integer, and
the property value is the node path.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The work area buffer returned by the ibm,update-properties rtas call contains
20 bytes of header information prior to the property value descriptor data.
Currently update_dt_node tries to advance over this header using sizeof(upwa).
The update_props_workarea struct contains 20 bytes worth of fields, that map
to the relevant header data, but the sizeof the structure is 24 bytes due to
4 bytes of padding at the end of the structure. Packing the structure ensures
that we don't advance too far over the rtas buffer.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The rc variable is initially used to store the return code from the
ibm,update-properties rtas call which returns 0 or 1 on success. A return
code of 1 indicates that ibm,update-properties must be called again for the
node. However, the rc variable is overwritten by a call to update_dt_prop
which returns 0 on success. This results in ibm,update-properties not being
called again for the given node when the rtas call rc was previously 1.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The update_dt_prop helper function fails to set the IN/OUT parameter prop to
NULL after a complete property has been parsed from the work area returned by
the ibm,update-properties rtas function. This results in the property list of
the device node being updated is corrupted and becomes a loop since the same
property structure is used repeatedly.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the program check handler we handle some causes with interrupts off
and others with interrupts on.
We need to enable interrupts to handle the emulation cases, because they
access userspace memory and might sleep.
For faults in the kernel we don't want to do any emulation, and
emulate_instruction() enforces that. do_mathemu() doesn't but probably
should.
The other disadvantage of enabling interrupts for kernel faults is that
we may take another interrupt, and recurse. As seen below:
--- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1
[link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90
[c000000fb185dc10] 0000000000000000 (unreliable)
[c000000fb185dc80] c0000000007d8558 .program_check_exception+0x298/0x2d0
[c000000fb185dd00] c000000000002f40 emulation_assist_common+0x140/0x180
--- Exception: e40 at c000000000004ee0 performance_monitor_relon_pSeries_1
[link register ] c00000000000f858 .arch_local_irq_restore+0x38/0x90
[c000000fb185dff0] 00000000008b9190 (unreliable)
[c000000fb185e060] c0000000007d8558 .program_check_exception+0x298/0x2d0
So avoid both problems by checking if the fault was in the kernel and
skipping the enable of interrupts and the emulation. Go straight to
delivering the SIGILL, which for kernel faults calls die() and so on,
dropping us in the debugger etc.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes back traces and profiles easier to read.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The symbols that name some of our exception trampolines are ahead of the
location they name. In most cases this is OK because the code is tightly
packed, but in some cases it means the symbol floats ahead of the
correct location, eg:
c000000000000ea0 <performance_monitor_pSeries_1>:
...
c000000000000f00: 7d b2 43 a6 mtsprg 2,r13
Fix them all by moving the symbol after the set of the location.
While we're moving them anyway, rename them to loose the camelcase and
to make it clear that they are trampolines.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We haven't updated these for a while it seems, it's nice to have in the
oops output.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The spec says it "may be problematic" if CPU x registers the VPA of
CPU y. Add a warning in case we ever do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The VSX alignment handler needs to write out the existing VSX
state to memory before operating on it (flush_vsx_to_thread()).
If we take a VSX alignment exception in the kernel bad things
will happen. It looks like we could write the kernel state out
to the user process, or we could handle the kernel exception
using data from the user process (depending if MSR_VSX is set
or not).
Worse still, if the code to read or write the VSX state causes an
alignment exception, we will recurse forever. I ended up with
hundreds of megabytes of kernel stack to look through as a result.
Floating point and SPE code have similar issues but already include
a user check. Add the same check to emulate_vsx().
With this patch any unaligned VSX loads and stores in the kernel
will show up as a clear oops rather than silent corruption of
kernel or userspace VSX state, or worse, corruption of a potentially
unlimited amount of kernel memory.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As a part of pseries_idle backend driver cleanup to make
the code common to both pseries and powernv platforms, it
is necessary to move the backend-driver code to drivers/cpuidle.
As a pre-requisite for that, it is essential to move plpar_wrapper.h
to include/asm.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As a part of pseries_idle cleanup to make the backend driver
code common to both pseries and powernv.
Remove non-essential smt_snooze_delay declaration in pseries.h
header file and pseries.h file inclusion in
pseries/processor_idle.c
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The stmw instruction was incorrectly decoded as an update form instruction
and thus the RA register was being clobbered.
Also, the utility routine to write memory to unaligned addresses breaks the
operation into smaller aligned accesses but was incorrectly incrementing
the address by only one; it needs to increment the address by the size of
the smaller aligned chunk.
Signed-off-by: Tom Musta <tmusta@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Memory I/O resources need to be marked as busy or else we cannot remove
them when doing memory hot remove.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
KVM uses anon_inode_get() to allocate file descriptors as part
of some of its ioctls. But those ioctls are lacking a flag argument
allowing userspace to choose options for the newly opened file descriptor.
In such case it's advised to use O_CLOEXEC by default so that
userspace is allowed to choose, without race, if the file descriptor
is going to be inherited across exec().
This patch set O_CLOEXEC flag on all file descriptors created
with anon_inode_getfd() to not leak file descriptors across exec().
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://lkml.kernel.org/r/cover.1377372576.git.ydroneaud@opteya.com
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
C293PCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add device tree for SEC 6.0 used on C29x silicon.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update the 64-bit hibernation code to support Book E CPUs.
Some registers and instructions are not defined for Book3e
(SDR reg, tlbia instruction).
SDR: Storage Description Register. Book3S and Book3E have different
address translation mode, we do not need HTABORG & HTABSIZE to
translate virtual address to real address.
More registers are saved in BookE-64bit.(TCR, SPRG1)
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add this file to help detect cpu type in runtime.
These macros will be more favorable for driver
to apply errata and workaround to specified cpu type.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
prepare C preprocessor support when processing MPC512x DTS files
- switch from DTS syntax to CPP syntax for include specs
- create a symlink such that DTS processing can reference includes
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
reword the clock control module's registers declaration such that the
MCLK related registers form an array and get indexed by PSC controller
or CAN controller component number
this change is in preparation to COMMON_CLK support for the MPC512x
platform, the changed declaration remains neutral to existing code since
the PSC and MSCAN CCR fields declared here aren't referenced elsewhere
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 40b313608a ("Finally eradicate
CONFIG_HOTPLUG") removed remaining references to CONFIG_HOTPLUG, but missed
a few plain English references in the CONFIG_KEXEC help texts.
Remove them, too.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on a patch by Jon Mason (see URL below).
All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss". The "mpss" argument is redundant since we
can easily look it up internally. In addition, all callers check
"bus->self" for NULL, which we can also do internally.
This patch simplifies the interface and the callers. No functional change.
Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ve9i
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch moves the generalized implementation of of_get_cpu_node from
PowerPC to DT core library, thereby adding support for retrieving cpu
node for a given logical cpu index on any architecture.
The CPU subsystem can now use this function to assign of_node in the
cpu device while registering CPUs.
It is recommended to use these helper function only in pre-SMP/early
initialisation stages to retrieve CPU device node pointers in logical
ordering. Once the cpu devices are registered, it can be retrieved easily
from cpu device of_node which avoids unnecessary parsing and matching.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Currently different drivers requiring to access cpu device node are
parsing the device tree themselves. Since the ordering in the DT need
not match the logical cpu ordering, the parsing logic needs to consider
that. However, this has resulted in lots of code duplication and in some
cases even incorrect logic.
It's better to consolidate them by adding support for getting cpu
device node for a given logical cpu index in DT core library. However
logical to physical index mapping can be architecture specific.
PowerPC has it's own implementation to get the cpu node for a given
logical index.
This patch refactors the current implementation of of_get_cpu_node.
This in preparation to move the implementation to DT core library.
It separates out the logical to physical mapping so that a default
matching of the physical id to the logical cpu index can be added
when moved to common code. Architecture specific code can override it.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Unlike 64-bit, we don't currently support multiplatform between e500
and non-e500, so the -mcpu is not configurable at this time.
-msoft-float is specified when testing for -mcpu=8540 because otherwise
some older toolchains will fail with "error: E500 and FPRs not
supported".
Signed-off-by: Scott Wood <scottwood@freescale.com>
By default use -mcpu=powerpc64 rather than -mtune=power7
Add options for e5500/e6500, with fallbacks for older compilers.
Hide the POWER cpu options in booke configs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This caused lwsync to be converted to sync on 64-bit (on 32-bit lwsync
is generated at runtime, and so wasn't affected). Not using lwsync
caused a significant slowdown on certain workloads.
Setting this flag for any e500-enabled build is also not friendly to
multiplatform kernels.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some CPUs (such as e500v1/v2) don't implement mftb and will take a
trap. mfspr should work on everything that has a timebase, and is the
preferred instruction according to ISA v2.06.
Currently we get away with mftb on 85xx because the assembler converts
it to mfspr due to -Wa,-me500. However, that flag has other effects
that are undesireable for certain targets (e.g. lwsync is converted to
sync), and is hostile to multiplatform kernels. Thus we would like to
stop setting it for all e500-family builds.
mftb/mftbu instances which are in 85xx code or common code are
converted. Instances which will never run on 85xx are left alone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Erratum A-006598 says that 64-bit mftb is not atomic -- it's subject
to a similar race condition as doing mftbu/mftbl on 32-bit. The lower
half of timebase is updated before the upper half; thus, we can share
the workaround for a similar bug on Cell. This workaround involves
looping if the lower half of timebase is zero, thus avoiding the need
for a scratch register (other than CR0). This workaround must be
avoided when the timebase is frozen, such as during the timebase sync
code.
This deals with kernel and vdso accesses, but other userspace accesses
will of course need to be fixed elsewhere.
Signed-off-by: Scott Wood <scottwood@freescale.com>
If data returned from pstore is compressed, nvram's write callback
will add a flag ERR_TYPE_KERNEL_PANIC_GZ indicating the data is compressed
while writing to nvram. If the data read from nvram is compressed, nvram's
read callback will set the flag 'compressed'. The patch adds backward
compatibilty with old format oops header when reading from pstore.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Backends will set the flag 'compressed' after reading the log from
persistent store to indicate the data being returned to pstore is
compressed or not.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Addition of new argument 'compressed' in the write call back will
help the backend to know if the data passed from pstore is compressed
or not (In case where compression fails.). If compressed, the backend
can add a tag indicating the data is compressed while writing to
persistent store.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
(De)compression support is provided in pstore in subsequent patches which
needs an additional argument 'compressed' to determine if the data
is compressed or not. This patch will take care of removing (de)compression
in nvram with pstore which was making use of 'hsize' argument in pstore write
as 'hsize' will be removed in the subsequent patch.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When reworking udbg_16550.c I forgot to remove the old and now useless
code for the CONFIG_PPC_EARLY_DEBUG_WSP case, which doesn't build as
a result. I also missed a cast.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSCDSjAAoJEHm+PkMAQRiGDXMIAI7Loae0Oqb1eoeJkvjyZsBS
OJDeeEcn+k58VbxVHyRdc7hGo4yI4tUZm172SpnOaM8sZ/ehPU7zBrwJK2lzX334
/jAM3uvVPfxA2nu0I4paNpkED/NQ8NRRsYE1iTE8dzHXOH6dA3mgp5qfco50rQvx
rvseXpME4KIAJEq4jnyFZF5+nuHiPueM9JftPmSSmJJ3/KY9kY1LESovyWd7ttg1
jYSVPFal9J0E+tl2UQY5g9H16GqhhjYn+39Iei6Q5P4bL4ZubQgTRQTN9nyDc06Z
ezQtGoqZ8kEz/2SyRlkda6PzjSEhgXlc8mCL5J7AW+dMhTHHx2IrosjiCA80kG8=
=c0rK
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc5' into perf/core
Merge Linux 3.11-rc5, to sync up with the latest upstream fixes since -rc1.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull nohz improvements from Frederic Weisbecker:
" It mostly contains fixes and full dynticks off-case optimizations. I believe that
distros want to enable this feature so it seems important to optimize the case
where the "nohz_full=" parameter is empty. ie: I'm trying to remove any performance
regression that comes with NO_HZ_FULL=y when the feature is not used.
This patchset improves the current situation a lot (off-case appears to be around 11% faster
with hackbench, although I guess it may vary depending on the configuration but it should be
significantly faster in any case) now there is still some work to do: I can still observe a
remaining loss of 1.6% throughput seen with hackbench compared to CONFIG_NO_HZ_FULL=n. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the arch overrides some generic vtime APIs, let it describe
these on a dedicated and standalone header. This way it becomes
convenient to include it in vtime generic headers without irrelevant
stuff in such a low level header.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Following is a brief description of the PAMU hardware:
PAMU determines what action to take and whether to authorize the action on
the basis of the memory address, a Logical IO Device Number (LIODN), and
PAACT table (logically) indexed by LIODN and address. Hardware devices which
need to access memory must provide an LIODN in addition to the memory address.
Peripheral Access Authorization and Control Tables (PAACTs) are the primary
data structures used by PAMU. A PAACT is a table of peripheral access
authorization and control entries (PAACE).Each PAACE defines the range of
I/O bus address space that is accessible by the LIOD and the associated access
capabilities.
There are two types of PAACTs: primary PAACT (PPAACT) and secondary PAACT
(SPAACT).A given physical I/O device may be able to act as one or more
independent logical I/O devices (LIODs). Each such logical I/O device is
assigned an identifier called logical I/O device number (LIODN). A LIODN is
allocated a contiguous portion of the I/O bus address space called the DSA window
for performing DSA operations. The DSA window may optionally be divided into
multiple sub-windows, each of which may be used to map to a region in system
storage space. The first sub-window is referred to as the primary sub-window
and the remaining are called secondary sub-windows.
This patch provides the PAMU driver (fsl_pamu.c) and the corresponding IOMMU
API implementation (fsl_pamu_domain.c). The PAMU hardware driver (fsl_pamu.c)
has been derived from the work done by Ashish Kalra and Timur Tabi.
[For iommu group support]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Added the following domain attributes for the FSL PAMU driver:
1. Added new iommu stash attribute, which allows setting of the
LIODN specific stash id parameter through IOMMU API.
2. Added an attribute for enabling/disabling DMA to a particular
memory window.
3. Added domain attribute to check for PAMUV1 specific constraints.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add an iommu domain pointer to device (powerpc) archdata. Devices
are attached to iommu domains and this pointer provides a mechanism
to correlate between a device and the associated iommu domain. This
field is set when a device is attached to a domain.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Our ppc64 spinlocks and rwlocks use a trick where a lock token and
the paca index are placed in the lock with a single store. Since we
are using two u16s they need adjusting for little endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to set ELF_DATA correctly on LE coredumps.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add little endian support for demuxing SMP IPIs
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Alistair noticed we got a SIGILL on userspace mfpvr instructions.
Remove the little endian check in the emulation code, it is
probably there to protect against the old pseudo little endian
implementations but doesn't make sense for real little endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lppaca, slb_shadow and dtl_entry hypervisor structures are
big endian, so we have to byte swap them in little endian builds.
LE KVM hosts will also need to be fixed but for now add an #error
to remind us.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add endian annotation to various hypervisor structures which
are defined as big endian.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The device tree is big endian so make sure we byteswap on little
endian. We assume any pHyp calls also return big endian results in
memory.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We pass dma_window to of_parse_dma_window as a void * and then
run through hoops to cast it back to a u32 array. In the process
we lose endian annotation.
Simplify it by just passing a __be32 * down.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS expects arguments in the call buffer to be big endian so we
need to byteswap on little endian builds
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerPC the device tree is always big endian, but the CPU could be
either, so add be32_to_cpu where appropriate and change the types of
device tree data to __be32 etc to allow sparse to locate endian issues.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we have MMU on exceptions (POWER8) and a relocatable kernel, we
need to branch from the initial exception vectors at 0x0 to up high
where the kernel might be located. Currently we do this using the link
register.
Unfortunately this corrupts the link stack and instead we should use the
count register. We did this for the syscall entry path in:
6a40480 powerpc: Avoid link stack corruption in MMU on syscall entry path
but I stupidly forgot to do the same for other exceptions.
This patch changes the initial exception vectors to use the count
register instead of the link register when we need to branch up to the
relocated kernel.
I have a dodgy userspace test which loops calling a function that reads
the PVR (mfpvr in userspace will be emulated by the kernel via the
program check exception). On POWER8 and with CONFIG_RELOCATABLE=y, I
get a ~10% performance improvement with my userspace test with this
patch.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So far "/sys/devices/system/cpu/cpuX/topology/physical_package_id"
was always default (-1) on ppc64 architecture.
Now, some systems have an ibm,chip-id property in the cpu nodes in
the device tree. On these systems, we now use this information to
display physical_package_id.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
changes for V4:
- changes the type of frozen_pe_no from %d to %llu
in pr_devel()
'pe_no' hasn't been defined, it should be an typo error,
it should be 'frozen_pe_no'.
Also '__func__' has missed in IODA_EEH_DBG(),
For safety reasons, use pr_devel() directly, instead
of use IODA_EEH_DBG()
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds