- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
* lorenzo/pci/endpoint:
PCI: endpoint: Create configfs entry for each pci_epf_device_id table entry
misc: pci_endpoint_test: Use pci_irq_vector function
PCI: endpoint: functions/pci-epf-test: Replace lower into upper case characters
misc: pci_endpoint_test: Replace lower into upper case characters
PCI: endpoint: Replace mdelay with usleep_range() in pci_epf_test_write()
The PCIe controller dual mode is capable of operating in Root Complex
(RC) mode as well as EP mode by configuration option.
Add EP support to the DesignWare driver on top of RC mode support.
Add new property on pci_epc structure which allow to configure
pci_epf_test driver accordingly to the controller specific requirements.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Replace all initial lower case character into upper case in comments
and debug printks.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci_epf_test_write() is never called in atomic context.
The call chain ending up at pci_epf_test_write() is:
[1] pci_epf_test_write() <- pci_epf_test_cmd_handler()
pci_epf_test_cmd_handler() is set as a parameter of INIT_DELAYED_WORK()
in pci_epf_test_probe().
This function is not called in atomic context.
Despite never getting called from atomic context, pci_epf_test_write()
calls mdelay() to busy wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar.
This is needed so that epc->ops->clear_bar() can clear the BAR pair,
if the BAR is 64-bits wide.
This also makes it possible for pci_epc_clear_bar() to sanity check
the flags.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
If a 64-bit BAR was set-up, we need to skip a BAR,
since a 64-bit BAR consists of a BAR pair.
We need to check what BAR width the epc->ops->set_bar() specific
implementation actually did set-up, since some drivers, like the
Cadence EP controller, sometimes sets up a 64-bit BAR, even though
a 32-bit BAR was requested.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add barno and flags to struct epf_bar.
That way we can simplify epc->ops->set_bar()/pci_epc_set_bar()
by passing a struct *epf_bar instead of a whole lot of arguments.
This is needed so that epc->ops->set_bar() implementations can
modify BAR flags. Will be utilized in a succeeding patch.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
If a BAR supports 64-bit width or not depends on the hardware,
and should thus not depend on sizeof(dma_addr_t).
If a certain hardware doesn't support 64-bit BARs, its
epc->ops->set_bar() implementation should return -EINVAL
when PCI_BASE_ADDRESS_MEM_TYPE_64 is set.
We can't change pci_epc_set_bar() to only set
PCI_BASE_ADDRESS_MEM_TYPE_64 based on size, since if the user,
for some reason, wants to configure a BAR with a 64-bit width,
even though the BAR size is less than 4 GB, he should be able
to do that.
However, since pci-epf-test is simply a test and not an API,
we can set PCI_BASE_ADDRESS_MEM_TYPE_64 in pci-epf-test itself
only based on size.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
This patch updates the prototype of most handlers from 'struct
pci_epc_ops' so the EPC library can now support multi-function devices.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add SPDX GPL-2.0 to all PCI files that specified the GPL version 2 license.
Remove the boilerplate GPL version 2 language, relying on the assertion in
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") that the SPDX identifier may be used instead of the
full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_epf_test_raise_irq() reads the interrupt to use for the response from
reg->command, but this has been cleared at the beginning of the command
handler so the value is always zero at this point.
Instead, extract the interrupt index before handling the command and then
pass the requested interrupt into pci_epf_test_raise_irq(). This allows us
to remove the specific code to extract the interrupt for
COMMAND_RAISE_MSI_IRQ since it is now handled in common code.
Fixes: 3ecf3232c5 ("PCI: endpoint: Do not reset *command* inadvertently")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
epf_test is allocated using devm_kzalloc(). Hence it's not required to
explicitly free it in remove() callback. Since ->remove() callback doesn't
do anything other than freeing epf_test, remove the ->remove() callback.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Certain platforms like TI's K2G doesn't support link-up notification. Add
support to poll early (without waiting for the linkup notification) for
commands from the host.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_epf_test always maps the PCI_ENDPOINT_TEST registers to BAR_0. But if
BAR_0 is reserved for some other purpose (like in TI's K2G BAR_0 is mapped
to application registers and cannot be used to map any other regions),
PCI_ENDPOINT_TEST registers cannot be mapped making pci_epf_test unusable.
Add support to use any BAR to map PCI_ENDPOINT_TEST registers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_epf_test_cmd_handler() is the delayed work function which reads
*command* (set by the host) and performs various actions requested by the
host periodically. If the value in *command* is '0', it goes to the
reset_handler where it resets *command* to '0' and queues
pci_epf_test_cmd_handler().
However if the host writes a value to the *command* just after the
pci-epf-test driver checks *command* for '0' and before the control goes to
reset_handler, the *command* will be reset to '0' and the pci-epf-test
driver won't be able to perform the actions requested by the host. Fix it
here by not resetting the *command* in the reset_handler.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
struct pci_epf_test_reg is the MEMSPACE of pci-epf-test function driver
that will be accessed by the "host" for programming the pci-epf-test
device. So this structure shouldn't be subjected to compiler optimization
in pci_epf_test_cmd_handler() since the values can be changed by code
outside the scope of current code at any time.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI endpoint test driver uses crc32_le() so it should select
CRC32. Fixes this build error (when CRC32=m):
drivers/built-in.o: In function `pci_epf_test_cmd_handler':
pci-epf-test.c:(.text+0x2d98d): undefined reference to `crc32_le'
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Adds a new endpoint function driver (to program the virtual test device)
making use of the EP-core library.
[bhelgaas: fold in pci_epf_test_probe() -ENOMEM test from Wei Yongjun
<weiyongjun1@huawei.com>]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas