Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.
The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.
This is not obvious and it normally takes some time to
figure out.
To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Embedded systems often connect to sensors or other multimedia
subdevices directly. Currently, to be able to select such a
subdevice (e.g. CONFIG_VIDEO_OV5640) disabling of the auto-
select config option is needed (CONFIG_MEDIA_SUBDRV_AUTOSELECT).
This is inconvenient as the ancillary drivers for a particular
device then need to be selected manually.
Allow to select drivers manually while keeping the auto-select
feature in case EXPERT (selected by EMBEDDED) is enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds a frontend driver for the Socionext/Panasonic
MN884434 and MN884433 ISDB-S/T demodulators.
The maximum and minimum frequency of MN88443x comes from
ISDB-S and ISDB-T so frequency range is the following:
- ISDB-S (BS/CS110 IF frequency, Local freq 10.678GHz)
- Min: BS-1: 1032MHz
- Max: ND24: 2070MHz
- ISDB-T
- Min: ch13: 470MHz
- Max: ch62: 770MHz
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This script was moved out of Documentation/dvb, but the
links weren't updated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Three really tiny minors in this single commit which all on their own
would just clutter up the commit history unnecessarily:
* ddbridge-regs.h is lacking an include guard. Add it.
* Fix an unnecessary NULL initialisation in ddbridge-ci. The declaration
of the ci struct ptr is immediately followed by kzalloc().
* Clarify that the CXD2099AR is a Sony device in the cxd2099 driver at a
few places including Kconfig.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CIMaX SP2 driver is a EN50221 CI controller I2C driver similar to the
cxd2099 driver. Move it's Kconfig block into the newly introduced CI
subsection.
Cc: Olli Salonen <olli.salonen@iki.fi>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cxd2099 driver makes use of the Regmap I2C kernel API, thus add
"select REGMAP_I2C" to it's Kconfig block. Also, make it default "m" if
!MEDIA_SUBDRV_AUTOSELECT, just like every other dvb-frontend driver.
And, while at it, remove the hyphens around the help tag.
Cc: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the Makefile, Kconfig files of driver
and MAINTAINERS file update about the driver
for the Sony CXD2880 DVB-T2/T tuner + demodulator.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the TODO file, this driver only landed in staging because of
the way device nodes and data transfers are handled. Besides that this way
(use of secX devices) has become sort of standard to date (ie. VDR
supports this literally since ages via the ddci plugin, TVHeadend received
this functionality lately, and minisatip being currently worked on
regarding this), most importantly this I2C client only driver isn't even
responsible for setting up device nodes, not for handling data
transfer and so on, but only serves as interface for the dvb_ca_en50221
subsystem, just like every other DVB card out in the wild, with hard-wired
or such flexible CA interfaces. And, it would even work with cards having
the cxd2099 controller hard-wired.
Also, this driver received quite some love and even is a proper I2C client
driver by now. So, as this driver acts as a EN50221 frontend device, move
it to dvb-frontends. There is no need to keep it buried in staging.
This commit also updates all affected Kconfig and Makefile's, and adds
MEDIA_AUTOSELECT depends to ddbridge and ngene.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
I went through all Kconfigs under drivers/media and fixed any bad help
sections. This makes it conform to the common practice and should fix
problems with 'make menuconfig' when using media_build. This is due to
a "WARNING" message that media_build can insert in the Kconfig and that
assumes the help text is indented by at least two spaces. If not, then the
Kconfig becomes invalid and 'make menuconfig' fails.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds the frontend driver for the MaxLinear MxL5xx family of tuner-
demodulators, as used on Digital Devices MaxS4/8 four/eight-tuner cards.
The driver was picked from the dddvb vendor driver package and - judging
solely from the diff - has undergone a 100% rework:
- Silly #define's used to pass multiple values to functions were
expanded. This resulted in macro/register names not being usable
anymore for such occurences, but makes the code WAY more read-,
understand- and maintainable.
- CamelCase was changed to kernel_case
- All typedef were removed
- Overall code style was fixed, besides >80char lines in _defs.h and
_regs.h, checkpatch is happy.
- Also, signal stat acquisition was made to comply with the DVB API
ways to do these things.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a frontend driver for the ST STV6111 DVB-S/S2 tuners. Like the
stv0910 demod frontend driver, this driver originates from the Digital
Devices' dddvb vendor driver package as of version 0.9.29, and was cleaned
up aswell. No functionality had to be removed though. Any camel case has
been converted to kernel_case, fixup patch has been proposed upstream.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a multi frontend driver for the ST STV0910 DVB-S/S2 demodulator
frontends. The driver code originates from the Digital Devices' dddvb
vendor driver package as of version 0.9.29, and has been cleaned up from
core API usage which isn't supported yet in the kernel, and additionally
all obvious style issues have been resolved. All camel case and allcaps
have been converted to kernel_case and lowercase. Patches have been sent
to the vendor package maintainers to fix this aswell. Signal statistics
acquisition has been refactored to comply with standards.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use regmap for register access. Own low level i2c read and write
routines for regmap is still needed because chip uses single command
byte in addition to typical i2c register access.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds an i2c mux to the lgdt3306a demodulator. This was done to support
the Hauppauge WinTV-dualHD 01595 USB TV tuner (em28xx), which utilizes two
si2157 tuners behind gate control.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unused demod driver. Device that used it never went public.
If someone later decide to add support for a device using this
chipset, it should be easy enough to retrieve it from git
history.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ZyDAS ZD1301 is chip having USB interface and DVB-T demodulator
integrated. This driver is for demodulator part.
Driver is very reduced, just basic demodulator functionality, no
statistics at all. It registers as a platform driver to driver core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some weird randconfigs, it is possible to select DVB
drivers, without having the DVB_CORE:
CONFIG_DVB_AU8522=m
CONFIG_DVB_AU8522_V4L=m
CONFIG_DVB_TUNER_DIB0090=m
This was never supposed to work, but changeset 22a613e898
("[media] dvb_frontend: merge duplicate dvb_tuner_ops.release implementations")
caused it to be exposed:
drivers/built-in.o: In function `fc0011_attach':
(.text+0x1598fb): undefined reference to `dvb_tuner_simple_release'
drivers/built-in.o:(.rodata+0x55e58): undefined reference to `dvb_tuner_simple_release'
drivers/built-in.o:(.rodata+0x57398): undefined reference to `dvb_tuner_simple_release'
Fixes: 22a613e898 ("[media] dvb_frontend: merge duplicate dvb_tuner_ops.release implementations")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DVB binding schema at the DVB core assumes that the frontend is a
separate driver. Faling to do that causes OOPS when the module is
removed, as it tries to do a symbol_put_addr on an internal symbol,
causing craches like:
WARNING: CPU: 1 PID: 28102 at kernel/module.c:1108 module_put+0x57/0x70
Modules linked in: dvb_usb_gp8psk(-) dvb_usb dvb_core nvidia_drm(PO) nvidia_modeset(PO) snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd soundcore nvidia(PO) [last unloaded: rc_core]
CPU: 1 PID: 28102 Comm: rmmod Tainted: P WC O 4.8.4-build.1 #1
Hardware name: MSI MS-7309/MS-7309, BIOS V1.12 02/23/2009
Call Trace:
dump_stack+0x44/0x64
__warn+0xfa/0x120
module_put+0x57/0x70
module_put+0x57/0x70
warn_slowpath_null+0x23/0x30
module_put+0x57/0x70
gp8psk_fe_set_frontend+0x460/0x460 [dvb_usb_gp8psk]
symbol_put_addr+0x27/0x50
dvb_usb_adapter_frontend_exit+0x3a/0x70 [dvb_usb]
From Derek's tests:
"Attach bug is fixed, tuning works, module unloads without
crashing. Everything seems ok!"
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This avoids some low-level operations.
It has the benefit that now register values van be read from /sys/kernel/debug/regmap
The maximum register value is just a guess - all higher addresses read as zero.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move mn88472 DVB-T/T2/C demod driver out of staging to media.
v2: Fix build error reported by kbuild test robot:
drivers/staging/media/mn88472/Makefile: No such file or directory
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is Sony HELENE DVB-S/S2 DVB-T/T2 DVB-C/C2 ISDB-T/S tuner
driver (CXD2858ER).
Tuner is used on NetUP Dual Universal DVB CI card (hardware revision 1.4).
Use 'helene_attach_s' to attach tuner in 'satellite mode'.
Use 'helene_attach' for 'terrestrial mode'.
Satellite delivery systems supported:
DVB-S/S2, ISDB-S
Terrestrial delivery systems supported:
DVB-T/T2, ISDB-T
Cable delivery systems supported:
DVB-C/C2
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without I get this error for by dvb-card:
tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
cx23885_dvb_register() dvb_register failed err = -22
cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add DVB SEC frontend driver for STM LNBH25PQR chip.
[mchehab@osg.samsung.com: fix merge conflict:
fe_sec_voltage_t should not be used in kernelspace anymore.
instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the DVB Frontends menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use regmap for I2C register access.
Remove own I2C repeated mutex as it should not be needed. I2C adapter
lock is already taken when I2C mux adapter is called, no need for
double locking.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename driver state from priv to dev.
Use I2C client for correct logging.
Use adapter and address from I2C client structure where needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes DVB-S/DVB-S2 to the more commonly used
DVB-S/S2 in the description for DVB_CX24120
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the Technisat Skystar S2 - this
has been tried before but the cx24120 driver was a bit out of shape
and it didn't got any further:
https://patchwork.linuxtv.org/patch/10575/
It is an old card, but currently being sold off for next to nothing,
so it's proving quite popular of late. Noticing it's quite similar
to the cx24116 and cx24117 I've rewritten the driver in a similar way.
There were a few registers and commands from those drivers
missing from this one I've tested out and found they do something so
they've been added in to speed up tuning and to make get_frontend
return something useful.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick.Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ATSC/QAM-B demodulator is used by several new devices.
Add support for it. Other patches will fix CodingStyle issues.
Signed-off-by: Fred Richter <frichter@hauppauge.com>
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to I2C RegMap API. That offers unified register
access routines, register value caching and more.
We need 3 register maps, one for each register page, as chips has
3 I2C address.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ezequiel Garcia