This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQatYeAAoJEEEQszewGV1zv78QAIjWWnQgZlMrX+ol6r5w44bx
nnTLY22VE6GMliR9SagCo1VydjdZdsmLf03yLBP4Lmcc/PV4DmvJmX5l3cXxdCQe
CmFCMbSOTxpIM0mgrhqDjSl8mJkJEXd2RvgvQaeffqShzK7qSU7LZbbZDX/YnY6O
eb0UqgkQNXyutahq7qRKyVT3repb4EweA8wa45ix5Nx3Cco2PD7Pp5PV/LVlMHIf
hDL3+2RmGrKDa52r5aOfg6ZvOabGU7TVmT21V7VzbtPvwP4yGHrwt3SrgGRFfwTk
U8SwdT/DRVl44per8cxcdvxpde693xxxgWWVf01Exc5bOKfaaDjAh6fOdqbL0nkI
kQQrQt5F+tT8ODtwoaObu7w1SSHiquV6/dNHAz03S6TwsNs7fPfk9IiQpwHuFFUL
RSDZ3Z3dTmcU5PqhpRaPQwsPYWM7n9lF2uPZsH+uO+H1M0ag9w3Xz3up1nwRBzCC
jr+W5s3vmmDot9JSfbZGCAGelb2AdX3FL1iRF95QjbAAdJdzS/szmA4x01R/xJax
W8gfkgOr8mOiAdxqyS9LQu8cr1fn+e/6d2up0kBl0W7SPipeuUSd4SzJuSj9Zj9V
BA6RxYQxPFRuwwU6YfKui3jBaKgvcD1lWTF8lJHljn5NqB3IbUjWe3px9ZmLq6wA
nQLDXvuP36SbGTdkha0D
=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Kirkwood SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Dove SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a pinctrl driver core for Marvell SoCs plus DT
binding documentation. This core driver will be used by SoC family
specific drivers, i.e. Armada XP, Armada 370, Dove, Kirkwood, aso.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/Kconfig
Implement support for pinctrl on lantiq/falcon socs. The FALCON has 5 banks
of up to 32 pins.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Add information about the Exynos4210 pin banks and driver data which is
used by the Samsung pinctrl driver. In addition to this, the support for
external gpio and wakeup interrupt support is included and hooked up with
the Samsung pinctrl driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a new device tree enabled pinctrl and gpiolib driver for Samsung
SoC's. This driver provides a common and extensible framework for all
Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
driver supports only device tree based instantiation and hence can be
used only on those Samsung platforms that have device tree enabled.
This driver is split into two parts: the pinctrl interface and the gpiolib
interface. The pinctrl interface registers pinctrl devices with the pinctrl
subsystem and gpiolib interface registers gpio chips with the gpiolib
subsystem. The information about the pins, pin groups, pin functions and
gpio chips, which are SoC specific, are parsed from device tree node.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.
Changes since (implicit) v1
- remove references to file names in binding documentation
- remove sed commands from comments in driver
- add explicit numbers for pins and functions
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one-register-per-pin type device tree based pinctrl driver.
This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig entry for the COH901 pin controller depended on
PINMUX_U300 which is stale, use PINCTRL_U300 as it is called
these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
The nomadik gpio code has been converted to pinctrl, but the nomadik platform
still expects the old code to be present. Change it to use the new one instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xjdL
-----END PGP SIGNATURE-----
Merge tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/pinctrl
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
The spear/pinctrl branch has hard dependencies on both the
pinctrl branch and the clkdev branch. We merge those here
to fix it up without having to rebase a branch that has
been pulled into other stable branches already.
Conflicts:
Documentation/driver-model/devres.txt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This implements the pin configuration interface for the
Nomadik pin controller.
As part of the exercise we add a bit in the pin_cfg_t for
the Nomadik pinctrl driver that indicates if the pin should
be forced into GPIO mode. This is not done to go behind the
back of the GPIO subsystem, but to ensure that default modes
can be set by hogs on boot and system suspend/resume states.
It was used implicitly by the old code defining all config
settings and modes in a single config word but we now have
a split between pinmux and pinconf leading to the need to
have this.
We also add a bit for explicitly setting sleepmode of the
pin. This was previously handled by custom calls with the
_sleep() suffix, but we now have one single interface into
the configuration so we replace this with a bit indicating
that the pin shall be configured into sleep mode.
Some of the configuration can be refactored later to use
less custom fields on the pin_cfg_t but we are currently
leaving the old function calls in place so we stay
compatible.
ChangeLog v1->v2:
- Drop a hunk changing pinmuxing for GPIO and move it
over to the preceding pinmux patch.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implements basic pinmux for the Nomadik pin controller.
The plan is to split the existing singular pin config interface
nmk_config_pin(), nmk_config_pins(), that will configure muxing
and other settings at the same time, into two interfaces
by splitting the code in pinmux and pinctrl and eventually
deleting the old interface and its helper functions when all
users are gone.
nmk_gpio_set_mode() and nmk_gpio_get_mode() are two older
interfaces for just configuring muxing/altfunctions that
will also be replaced in the end.
We take some extra care to handle the glitch-avoidance here,
but it is simpler now since there is only one altsetting per
pingroup so we know immediately if we need to avoid altfunc
C glitches for a certain group.
As part of the makeover implement the .request() and .free()
calls on the GPIO chips and have them call back into the
pinctrl layer to reserve GPIOs.
ChangeLog v1->v2:
- Rebased on pinctrl-mergebase-20120418 so we get the latest
driver infrastructure where function count is done by a fixed
value and we can drop a few range checks since this is now
handled by the core.
- Include a GPIO muxing hunk erroneously part of the pin config
patch.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.
ChangeLog v1->v2:
- Base on the latest pinctrl development from
pinctrl-mergebase-20120418 so we can get rid of legacy
group count mechanism. Also drop the range checks for group
index, this is handled by the core now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl support for Freescale MXS SoCs, i.MX23 and i.MX28.
The driver supports device tree probe only.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver has mux and config support while the gpio is still
not supported.
For select input setting, the driver will handle it internally
and do not need user to take care of it.
The pinctrl-imx core driver will parse the dts file and dynamically
create the pinmux functions and groups.
Each IMX SoC pinctrl driver should register pins with a pin register map
including mux register and config register and select input map to core
for proper operations.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl driver for SPEAr platform. It also updates MAINTAINERS file
for SPEAr pinctrl drivers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
With the finalization of the external driver API and the device
tree support, this subsystem is now mature and can be promoted to
non-experimental status.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pin configuration support for the U300 driver pair,
we can now read out the biasing and drive mode in debugfs and
configure it using the new configuration API.
ChangeLog v1->v2:
- Migrate to pin config and generic pin config changes.
ChangeLog v2->v3:
- Adjust to generic pin config changes in v7 patch set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a split-off from the earlier patch set which adds generic
pin configuration for the pin controllers that want it. Since
we may have a system with mixed generic and custom pin controllers,
we pass a boolean in the pin controller ops vtable to indicate
if it is generic.
ChangeLog v1->v5:
- Follow parent patch versioning number system.
- Document the semantic meaning of return values from pin config
get functions, so we can iterate over pins and check their
properties from debugfs as part of the generic config code.
- Use proper cast functions in the generic debugfs pin config
file.
- Expand generic config to optionally cover groups too.
ChangeLog v5->v6:
- Update to match underlying changes.
ChangeLog v6->v7:
- Drop DRIVE_OFF parameter, use bias high impedance for this
- Delete argument for drive modes push-pull, od and os. These
are now just state transitions.
- Delete slew rate rising/falling due to discussions on on
proper semantics
- Drop config wakeup, struct irq_chip does this for now, add
back if need be.
- Set PIN_CONFIG_END to 0x7fff making room for custom config
parameters from 0x8000 and up.
- Prefix accessor functions with pinconf_
This adds a driver for the Tegra pinmux, and required parameterization
data for Tegra20 and Tegra30.
The driver is initially added with driver name and device tree compatible
value that won't cause this driver to be used. A later change will switch
the pinctrl driver to use the correct values, switch the old pinmux
driver to be disabled, and update all code that uses the old pinmux APIs
to use the new pinctrl APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
[squashed "fix case of Tegra30's foo_groups[] arrays"]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support PXA168/PXA910/MMP2 pinmux. Now only support function switch.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
[Rebase and fix some whitespace issues]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For stringent order, rename the pinmux-* pin controllers to
pinctrl-* and also rename the Kconfig symbols and in-kernel
users.
Cc: Rongjun Ying <Rongjun.Ying@csr.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This add per-pin and per-group pin config interfaces for biasing,
driving and other such electronic properties. The details of passed
configurations are passed in an opaque unsigned long which may be
dereferences to integer types, structs or lists on either side
of the configuration interface.
ChangeLog v1->v2:
- Clear split of terminology: we now have pin controllers, and
those may support two interfaces using vtables: pin
multiplexing and pin configuration.
- Break out pin configuration to its own C file, controllers may
implement only config without mux, and vice versa, so keep each
sub-functionality of pin controllers separate. Introduce
CONFIG_PINCONF in Kconfig.
- Implement some core logic around pin configuration in the
pinconf.c file.
- Remove UNKNOWN config states, these were just surplus baggage.
- Remove FLOAT config state - HIGH_IMPEDANCE should be enough for
everyone.
- PIN_CONFIG_POWER_SOURCE added to handle switching the power
supply for the pin logic between different sources
- Explicit DISABLE config enums to turn schmitt-trigger,
wakeup etc OFF.
- Update documentation to reflect all the recent reasoning.
ChangeLog v2->v3:
- Twist API around to pass around arrays of config tuples instead
of (param, value) pairs everywhere.
- Explicit drive strength semantics for push/pull and similar
drive modes, this shall be the number of drive stages vs
nominal load impedance, which should match the actual
electronics used in push/pull CMOS or TTY totempoles.
- Drop load capacitance configuration - I probably don't know
what I'm doing here so leave it out.
- Drop PIN_CONFIG_INPUT_SCHMITT_OFF, instead the argument zero to
PIN_CONFIG_INPUT_SCHMITT turns schmitt trigger off.
- Drop PIN_CONFIG_NORMAL_POWER_MODE and have a well defined
argument to PIN_CONFIG_LOW_POWER_MODE to get out of it instead.
- Drop PIN_CONFIG_WAKEUP_ENABLE/DISABLE and just use
PIN_CONFIG_WAKEUP with defined value zero to turn wakeup off.
- Add PIN_CONFIG_INPUT_DEBOUNCE for configuring debounce time
on input lines.
- Fix a bug when we tried to configure pins for pin controllers
without pinconf support.
- Initialized debugfs properly so it works.
- Initialize the mutex properly and lock around config tampering
sections.
- Check the return value from get_initial_config() properly.
ChangeLog v3->v4:
- Export the pin_config_get(), pin_config_set() and
pin_config_group() functions.
- Drop the entire concept of just getting initial config and
keeping track of pin states internally, instead ask the pins
what state they are in. Previous idea was plain wrong, if the
device cannot keep track of its state, the driver should do
it.
- Drop the generic configuration layout, it seems this impose
too much restriction on some pin controllers, so let them do
things the way they want and split off support for generic
config as an optional add-on.
ChangeLog v4->v5:
- Introduce two symmetric driver calls for group configuration,
.pin_config_group_[get|set] and corresponding external calls.
- Remove generic semantic meanings of return values from config
calls, these belong in the generic config patch. Just pass the
return value through instead.
- Add a debugfs entry "pinconf-groups" to read status from group
configuration only, also slam in a per-group debug callback in
the pinconf_ops so custom drivers can display something
meaningful for their pins.
- Fix some dangling newline.
- Drop dangling #else clause.
- Update documentation to match the above.
ChangeLog v5->v6:
- Change to using a pin name as parameter for the
[get|set]_config() functions, as suggested by Stephen Warren.
This is more natural as names will be what a developer has
access to in written documentation etc.
ChangeLog v6->v7:
- Refactor out by-pin and by-name get/set functions, only expose
the by-name functions externally, expose the by-pin functions
internally.
- Show supported pin control functionality in the debugfs
pinctrl-devices file.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the COH 901 driver request muxing of its GPIO pins
from the pinmux-u300 driver using the standard API calls.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver will be converted to a dual GPIO + pinctrl driver
since it supports biasing and driving control options. Hopefully
it can serve as an example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Machines that have embedded pin controllers need to select them
explicitly, so why broadcast their config options to menuconfig.
We provide a helpful submenu for those machines that do select
it, making it possible to enable debugging for example.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates a pin controller driver for the SiRFprinaII
pin mux portions.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[Fixup for changed function names and semantics in the v10 patch]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This adds a driver for the U300 pinmux portions of the system
controller "SYSCON". It also serves as an example of how to use
the pinmux subsystem. This driver also houses the platform data
for the only supported platform.
This deletes the old U300 driver in arch/arm/mach-u300 and
replace it with a driver using the new subsystem.
The new driver is considerably fatter than the old one, but it
also registers all 467 pins of the system and adds the power
and EMIF pin groups and corresponding functions. The idea
is to use this driver as a a reference for other
implementation so it needs to be as complete and verbose
as possible.
Reviewed-by: Barry Song <21cnbao@gmail.com>
[Fixup for changed function names and semantics in the v10 patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates a subsystem for handling of pin control devices.
These are devices that control different aspects of package
pins.
Currently it handles pinmuxing, i.e. assigning electronic
functions to groups of pins on primarily PGA and BGA type of
chip packages which are common in embedded systems.
The plan is to also handle other I/O pin control aspects
such as biasing, driving, input properties such as
schmitt-triggering, load capacitance etc within this
subsystem, to remove a lot of ARM arch code as well as
feature-creepy GPIO drivers which are implementing the same
thing over and over again.
This is being done to depopulate the arch/arm/* directory
of such custom drivers and try to abstract the infrastructure
they all need. See the Documentation/pinctrl.txt file that is
part of this patch for more details.
ChangeLog v1->v2:
- Various minor fixes from Joe's and Stephens review comments
- Added a pinmux_config() that can invoke custom configuration
with arbitrary data passed in or out to/from the pinmux driver
ChangeLog v2->v3:
- Renamed subsystem folder to "pinctrl" since we will likely
want to keep other pin control such as biasing in this
subsystem too, so let us keep to something generic even though
we're mainly doing pinmux now.
- As a consequence, register pins as an abstract entity separate
from the pinmux. The muxing functions will claim pins out of the
pin pool and make sure they do not collide. Pins can now be
named by the pinctrl core.
- Converted the pin lookup from a static array into a radix tree,
I agreed with Grant Likely to try to avoid any static allocation
(which is crap for device tree stuff) so I just rewrote this
to be dynamic, just like irq number descriptors. The
platform-wide definition of number of pins goes away - this is
now just the sum total of the pins registered to the subsystem.
- Make sure mappings with only a function name and no device
works properly.
ChangeLog v3->v4:
- Define a number space per controller instead of globally,
Stephen and Grant requested the same thing so now maps need to
define target controller, and the radix tree of pin descriptors
is a property on each pin controller device.
- Add a compulsory pinctrl device entry to the pinctrl mapping
table. This must match the pinctrl device, like "pinctrl.0"
- Split the file core.c in two: core.c and pinmux.c where the
latter carry all pinmux stuff, the core is for generic pin
control, and use local headers to access functionality between
files. It is now possible to implement a "blank" pin controller
without pinmux capabilities. This split will make new additions
like pindrive.c, pinbias.c etc possible for combined drivers
and chunks of functionality which is a GoodThing(TM).
- Rewrite the interaction with the GPIO subsystem - the pin
controller descriptor now handles this by defining an offset
into the GPIO numberspace for its handled pin range. This is
used to look up the apropriate pin controller for a GPIO pin.
Then that specific GPIO range is matched 1-1 for the target
controller instance.
- Fixed a number of review comments from Joe Perches.
- Broke out a header file pinctrl.h for the core pin handling
stuff that will be reused by other stuff than pinmux.
- Fixed some erroneous EXPORT() stuff.
- Remove mispatched U300 Kconfig and Makefile entries
- Fixed a number of review comments from Stephen Warren, not all
of them - still WIP. But I think the new mapping that will
specify which function goes to which pin mux controller address
50% of your concerns (else beat me up).
ChangeLog v4->v5:
- Defined a "position" for each function, so the pin controller now
tracks a function in a certain position, and the pinmux maps define
what position you want the function in. (Feedback from Stephen
Warren and Sascha Hauer).
- Since we now need to request a combined function+position from
the machine mapping table that connect mux settings to drivers,
it was extended with a position field and a name field. The
name field is now used if you e.g. need to switch between two
mux map settings at runtime.
- Switched from a class device to using struct bus_type for this
subsystem. Verified sysfs functionality: seems to work fine.
(Feedback from Arnd Bergmann and Greg Kroah-Hartman)
- Define a per pincontroller list of GPIO ranges from the GPIO
pin space that can be handled by the pin controller. These can
be added one by one at runtime. (Feedback from Barry Song)
- Expanded documentation of regulator_[get|enable|disable|put]
semantics.
- Fixed a number of review comments from Barry Song. (Thanks!)
ChangeLog v5->v6:
- Create an abstract pin group concept that can sort pins into
named and enumerated groups no matter what the use of these
groups may be, one possible usecase is a group of pins being
muxed in or so. The intention is however to also use these
groups for other pin control activities.
- Make it compulsory for pinmux functions to associate with
at least one group, so the abstract pin group concept is used
to define the groups of pins affected by a pinmux function.
The pinmux driver interface has been altered so as to enforce
a function to list applicable groups per function.
- Provide an optional .group entry in the pinmux machine map
so the map can select beteween different available groups
to be used with a certain function.
- Consequent changes all over the place so that e.g. debugfs
present reasonable information about the world.
- Drop the per-pin mux (*config) function in the pinmux_ops
struct - I was afraid that this would start to be used for
things totally unrelated to muxing, we can introduce that to
the generic struct pinctrl_ops if needed. I want to keep
muxing orthogonal to other pin control subjects and not mix
these things up.
ChangeLog v6->v7:
- Make it possible to have several map entries matching the
same device, pin controller and function, but using
a different group, and alter the semantics so that
pinmux_get() will pick all matching map entries, and
store the associated groups in a list. The list will
then be iterated over at pinmux_enable()/pinmux_disable()
and corresponding driver functions called for each
defined group. Notice that you're only allowed to map
multiple *groups* to the same
{ device, pin controller, function } triplet, attempts
to map the same device to multiple pin controllers will
for example fail. This is hopefully the crucial feature
requested by Stephen Warren.
- Add a pinmux hogging field to the pinmux mapping entries,
and enable the pinmux core to hog pinmux map entries.
This currently only works for pinmuxes without assigned
devices as it looks now, but with device trees we can
look up the corresponding struct device * entries when
we register the pinmux driver, and have it hog each
pinmux map in turn, for a simple approach to
non-dynamic pin muxing. This addresses an issue from
Grant Likely that the machine should take care of as
much of the pinmux setup as possible, not the devices.
By supplying a list of hogs, it can now instruct the
core to take care of any static mappings.
- Switch pinmux group retrieveal function to grab an
array of strings representing the groups rather than an
array of unsigned and rewrite accordingly.
- Alter debugfs to show the grouplist handled by each
pinmux. Also add a list of hogs.
- Dynamically allocate a struct pinmux at pinmux_get() and
free it at pinmux_put(), then add these to the global
list of pinmuxes active as we go along.
- Go over the list of pinmux maps at pinmux_get() time
and repeatedly apply matches.
- Retrieve applicable groups per function from the driver
as a string array rather than a unsigned array, then
lookup the enumerators.
- Make the device to pinmux map a singleton - only allow the
mapping table to be registered once and even tag the
registration function with __init so it surely won't be
abused.
- Create a separate debugfs file to view the pinmux map at
runtime.
- Introduce a spin lock to the pin descriptor struct, lock it
when modifying pin status entries. Reported by Stijn Devriendt.
- Fix up the documentation after review from Stephen Warren.
- Let the GPIO ranges give names as const char * instead of some
fixed-length string.
- add a function to unregister GPIO ranges to mirror the
registration function.
- Privatized the struct pinctrl_device and removed it from the
<linux/pinctrl/pinctrl.h> API, the drivers do not need to know
the members of this struct. It is now in the local header
"core.h".
- Rename the concept of "anonymous" mux maps to "system" muxes
and add convenience macros and documentation.
ChangeLog v7->v8:
- Delete the leftover pinmux_config() function from the
<linux/pinctrl/pinmux.h> header.
- Fix a race condition found by Stijn Devriendt in pin_request()
ChangeLog v8->v9:
- Drop the bus_type and the sysfs attributes and all, we're not on
the clear about how this should be used for e.g. userspace
interfaces so let us save this for the future.
- Use the right name in MAINTAINERS, PIN CONTROL rather than
PINMUX
- Don't kfree() the device state holder, let the .remove() callback
handle this.
- Fix up numerous kerneldoc headers to have one line for the function
description and more verbose documentation below the parameters
ChangeLog v9->v10:
- pinctrl: EXPORT_SYMBOL needs export.h, folded in a patch
from Steven Rothwell
- fix pinctrl_register error handling, folded in a patch from
Axel Lin
- Various fixes to documentation text so that it's consistent.
- Removed pointless comment from drivers/Kconfig
- Removed dependency on SYSFS since we removed the bus in
v9.
- Renamed hopelessly abbreviated pctldev_* functions to the
more verbose pinctrl_dev_*
- Drop mutex properly when looking up GPIO ranges
- Return NULL instead of ERR_PTR() errors on registration of
pin controllers, using cast pointers is fragile. We can
live without the detailed error codes for sure.
Cc: Stijn Devriendt <highguy@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds