Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The codec in the V3s is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the V3s does not have LINEIN, LINEOUT, MBIAS and MIC2,
MIC3, and the FIFO related registers are like H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PA gpio pin for controlling an external amplifier as used
on some Allwinner boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the boards have their headphone jack directly connected to the
matching pins of the SoCs. Since most of the time we will have the same
routing path, it makes no sense to put that in the DTS, since it will only
be some useless duplication there.
It also fixes the following warning messages that were seen so far, on
boards where we were using the bindings in the documentation example.
sun4i-codec 1c22c00.codec: ASoC: no sink widget found for Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: Failed to add route HP Left -> direct -> Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: no sink widget found for Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: Failed to add route HP Right -> direct -> Headphone Jack
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Allwinner SoCs have an in-SoC audio controller taking the role of a DAI
and a codec.
Add the binding documentation for that controller on the A10.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Marco Franchi