The cable_plugin member never receives an assignment, so it is always
false, which causes hdmi_enable_overflow_interrupts() to never
be called as per the logic below:
if (hdmi->cable_plugin && hdmi->sink_is_hdmi)
hdmi_enable_overflow_interrupts(hdmi);
This has been the case since the driver was originally introduced
in commit 9aaf880ed4 ("imx-drm: Add mx6 hdmi transmitter support").
Remove the cable_plugin element and the hdmi_enable_overflow_interrupts()
function that is never called.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # On R-Car H3
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1518812170-22687-1-git-send-email-festevam@gmail.com
We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).
This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-7-enric.balletbo@collabora.com
We would meet a short black screen when exit PSR with the full link
training, In this case, we should use fast link train instead of full
link training.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[dropped header reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-6-enric.balletbo@collabora.com
There is a race between AUX CH bring-up and enabling bridge which will
cause link training to fail. To avoid hitting it, don't change psr state
while enabling the bridge.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-4-enric.balletbo@collabora.com
Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-2-enric.balletbo@collabora.com
Currently MHL chip must be turned on permanently to detect MHL cable. It
duplicates micro-USB controller's (MUIC) functionality and consumes
unnecessary power. Lets use extcon attached to MUIC to enable MHL chip
only if it detects MHL cable.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The following happens when connection a DVI output driven
from the SiI9022 using a DVI-to-VGA adapter plug:
i2c i2c-0: sendbytes: NAK bailout.
i2c i2c-0: sendbytes: NAK bailout.
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305101702.13441-1-linus.walleij@linaro.org
If there is another bridge after analogix_dp, then the connector object
should not be created. This fixes following timeouts on Exynos5420-based
Chromebook2 Peach-PIT board during boot:
exynos-dp 145b0000.dp-controller: AUX CH cmd reply timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-4-m.szyprowski@samsung.com
The bridge does not need to be powered in analogix_dp_bind(), so
remove the calls to pm_runtime_get()/phy_power_on()/analogix_dp_init_dp()
as well as their power-off counterparts.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[the patch originally just removed the power_on portion, seanpaul removed
the power off code as well as improved the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-2-m.szyprowski@samsung.com
The Amlogic Meson GX SoCs, embedded the v2.01a controller, has been also
identified needing this workaround.
This patch adds the corresponding version to enable a single iteration for
this specific version.
Fixes: be41fc55f1 ("drm: bridge: dw-hdmi: Handle overflow workaround based on device version")
Acked-by: Archit Taneja <architt@codeaurora.org>
[narmstrong: s/identifies/identified and rebased against Jernej's change]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519386277-25902-1-git-send-email-narmstrong@baylibre.com
The readl_poll_timeout() return value is 0 in case of success
so it is better to detect errors without taking care of the
return value sign.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180204213624.18288-1-philippe.cornu@st.com
Since we are initing connector in the core driver and encoder in the
plat driver, let's clean them up in the right places.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-3-thierry.escande@collabora.com
The driver that instantiates the bridge should own the drvdata, as all
driver model callbacks (probe, remove, shutdown, PM ops, etc.) are also
owned by its driver struct. Moreover, storing two different pointer
types in driver data depending on driver initialization status is barely
a good practice and in fact has led to many bugs in this driver.
Let's clean up this mess and change Analogix entry points to simply
accept some opaque struct pointer, adjusting their users at the same
time to avoid breaking the compilation.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-2-thierry.escande@collabora.com
dw_hdmi shouldn't set drvdata since some drivers might need to store
it's own data there. Rework dw_hdmi in a way to return struct dw_hdmi
instead to store it in drvdata. This way drivers are responsible to
store and pass structure when needed.
Idea was taken from the following commit:
8242ecbd59 ("drm/bridge/synopsys: stop clobbering drvdata")
Cc: p.zabel@pengutronix.de
Cc: Laurent.pinchart@ideasonboard.com
Cc: hjc@rock-chips.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-6-jernej.skrabec@siol.net
Parts of PHY code could be useful also for custom PHYs. For example,
Allwinner A83T has custom PHY which is probably Synopsys gen2 PHY
with few additional memory mapped registers, so most of the Synopsys PHY
related code could be reused.
Functions exported here are actually not specific to Synopsys PHYs but
to DWC HDMI controller PHY interface. This means that even if the PHY is
completely custom, i.e. not designed by Synopsys, exported functions can
be useful.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-5-jernej.skrabec@siol.net
Allwinner SoCs have dw hdmi controller v1.32a which exhibits same
magenta line issue as i.MX6Q and i.MX6DL. Enable workaround for it.
Tests show that one iteration is enough.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-4-jernej.skrabec@siol.net
Add support for the Synopsys DesignWare MIPI DSI version 1.31
Two registers need to be updated/added for supporting 1.31:
* PHY_TMR_CFG 0x9c (updated)
1.30 [31:24] phy_hs2lp_time
[23:16] phy_lp2hs_time
[14: 0] max_rd_time
1.31 [25:16] phy_hs2lp_time
[ 9: 0] phy_lp2hs_time
* PHY_TMR_RD_CFG 0xf4 (new)
1.31 [14: 0] max_rd_time
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206084251.303-1-philippe.cornu@st.com
The dw_mipi_dsi_host_transfer() must return the number of
bytes transmitted/received on success instead of 0.
Note: As the read feature is not implemented, only the
transmitted number of bytes is returned for the moment.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-3-philippe.cornu@st.com
The dcs/generic dsi read feature is not yet implemented so it
is important to warn the host_transfer() caller in case of
read operation requests.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-2-philippe.cornu@st.com
It's been a while since we've backmerged drm-next. Dave just brought
back 4.15-rc8, so now's a good time to freshen things up around here.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031142149.32512-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We're filling the "remainder" word with little-endian data, then writing
it out to IO registers with endian-correcting writel(). That probably
won't work on big-endian systems.
Let's mark the "remainder" variable as LE32 (since we fill it with
memcpy()) and do the swapping explicitly.
Some of this function could be done more easily without memcpy(), but
the unaligned "remainder" case is a little hard to do without
potentially overrunning 'tx_buf', so I just applied the same solution in
all cases (memcpy() + le32_to_cpu()).
Tested only on a little-endian system.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203248.139249-2-briannorris@chromium.org
This takes care of 2 TODOs in this driver, by using the common DSI
packet-marshalling code instead of our custom short/long write code.
This both saves us some duplicated code and gets us free support for
command types that weren't already part of our switch block (e.g.,
MIPI_DSI_GENERIC_LONG_WRITE).
The code logic stays mostly intact, except that it becomes unnecessary
to split the short/long write functions, and we have to copy data a bit
more.
Along the way, I noticed that loop bounds were a little odd:
while (DIV_ROUND_UP(len, pld_data_bytes))
This really was just supposed to be 'len != 0', so I made that more
clear.
Tested on RK3399 with some pending refactoring patches by Nickey Yang,
to make the Rockchip DSI driver wrap this common driver.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203248.139249-1-briannorris@chromium.org
sparse complains:
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c:703:6: warning: symbol
'dw_mipi_dsi_bridge_mode_set' was not declared. Should it be static?
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203319.139520-1-briannorris@chromium.org
This extends the dumb VGA DAC bridge to handle the THS8134A
and THS8134B VGA DACs in addition to those already handled.
We assign the proper timing data to the pointer inside the
bridge struct so display controllers that need to align their
timings to the bridge can pick it up and work from there.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112074854.9560-3-linus.walleij@linaro.org
Bridge drivers/helpers shouldn't be clobbering the drvdata, since a
parent driver might need to own this. Instead, let's return our
'dw_mipi_dsi' object and have callers pass that back to us for removal.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128010538.119114-1-briannorris@chromium.org
This patch removes an unreachable code found by the SVACE static
analysis:
UNREACHABLE_CODE: This statement in the source code might be unreachable
during program execution.
[unreachable] unreachable at drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:787
retval != 0 is always false because at this program point the variable retval
is always equal to 0 at drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:786
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171212112037.13107-1-s.nawrocki@samsung.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaNy81AAoJEHm+PkMAQRiGq2YH/1C1so18qErhPosdfeLIXLbA
iC9XcIvkPuMfjDw4EfSWOzhKnzgqGuc8q/Vzz0ulDreNVUb52nBeRy69QgNoZBTB
NkLdrUKBnlArvRhBXToQGW/s1eI/gobuHBJb7/fbpvsUtPYcDE2nUXAEsMlagn5L
BMHNzE3TByaWj0SqJtZAZvaQN2MdWV8ArHBPaC+MtR2C1VJIyl0mT9CdCu2NpTES
+FncKJ6/qplSBNSUJSfYmFLfEKVcQxvHMi1kp9jOGlVjPM3cOPKRpv8x69x/IPoB
3l82AikL+Ju0738oJ0Fp/IhfGUqpXz+FwUz1JmCdrcOby75RHomJuJCUBTtjXA4=
=lYkx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc4' into drm-next
Linux 4.15-rc4
Daniel requested it to fix some messy conflicts.
get_modes() callback might be called asynchronously from the DRM core and
it is not synchronized with bridge_enable(), which sets proper runtime PM
state of the main DP device. Fix this by calling pm_runtime_get_sync()
before calling drm_get_edid(), which in turn calls drm_dp_i2c_xfer() and
analogix_dp_transfer() to ensure that main DP device is runtime active
when doing any access to its registers.
This fixes the following kernel issue on Samsung Exynos5250 Snow board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 62 Comm: kworker/0:2 Not tainted 4.13.0-rc2-00364-g4a97a3da420b #3357
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events output_poll_execute
task: edc14800 task.stack: edcb2000
PC is at analogix_dp_transfer+0x15c/0x2fc
LR is at analogix_dp_transfer+0x134/0x2fc
pc : [<c0468538>] lr : [<c0468510>] psr: 60000013
sp : edcb3be8 ip : 0000002a fp : 00000001
r10: 00000000 r9 : edcb3cd8 r8 : edcb3c40
r7 : 00000000 r6 : edd3b380 r5 : edd3b010 r4 : 00000064
r3 : 00000000 r2 : f0ad3000 r1 : edcb3c40 r0 : edd3b010
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4000406a DAC: 00000051
Process kworker/0:2 (pid: 62, stack limit = 0xedcb2210)
Stack: (0xedcb3be8 to 0xedcb4000)
[<c0468538>] (analogix_dp_transfer) from [<c0424ba4>] (drm_dp_i2c_do_msg+0x8c/0x2b4)
[<c0424ba4>] (drm_dp_i2c_do_msg) from [<c0424e64>] (drm_dp_i2c_xfer+0x98/0x214)
[<c0424e64>] (drm_dp_i2c_xfer) from [<c057b2d8>] (__i2c_transfer+0x140/0x29c)
[<c057b2d8>] (__i2c_transfer) from [<c057b4a4>] (i2c_transfer+0x70/0xe4)
[<c057b4a4>] (i2c_transfer) from [<c0441de4>] (drm_do_probe_ddc_edid+0xb4/0x114)
[<c0441de4>] (drm_do_probe_ddc_edid) from [<c0441e5c>] (drm_probe_ddc+0x18/0x28)
[<c0441e5c>] (drm_probe_ddc) from [<c0445728>] (drm_get_edid+0x124/0x2d4)
[<c0445728>] (drm_get_edid) from [<c0465ea0>] (analogix_dp_get_modes+0x90/0x114)
[<c0465ea0>] (analogix_dp_get_modes) from [<c0425e8c>] (drm_helper_probe_single_connector_modes+0x198/0x68c)
[<c0425e8c>] (drm_helper_probe_single_connector_modes) from [<c04325d4>] (drm_setup_crtcs+0x1b4/0xd18)
[<c04325d4>] (drm_setup_crtcs) from [<c04344a8>] (drm_fb_helper_hotplug_event+0x94/0xd0)
[<c04344a8>] (drm_fb_helper_hotplug_event) from [<c0425a50>] (drm_kms_helper_hotplug_event+0x24/0x28)
[<c0425a50>] (drm_kms_helper_hotplug_event) from [<c04263ec>] (output_poll_execute+0x6c/0x174)
[<c04263ec>] (output_poll_execute) from [<c0136f18>] (process_one_work+0x188/0x3fc)
[<c0136f18>] (process_one_work) from [<c01371f4>] (worker_thread+0x30/0x4b8)
[<c01371f4>] (worker_thread) from [<c013daf8>] (kthread+0x128/0x164)
[<c013daf8>] (kthread) from [<c0108510>] (ret_from_fork+0x14/0x24)
Code: 0a000002 ea000009 e2544001 0a00004a (e59537c8)
---[ end trace cddc7919c79f7878 ]---
Reported-by: Misha Komarovskiy <zombah@gmail.com>
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121074936.22520-1-m.szyprowski@samsung.com
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
Fields in HTIM01 and HTIM02 regs should be even.
Recomended thresh_dly value is max_tu_symbol.
Remove set of VPCTRL0.VSDELAY as it is related to DSI input
interface. Currently driver supports only DPI.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510073785-16108-5-git-send-email-andrey.gusakov@cogentembedded.com
The panel_bridge bridge attaches to the panel's OF node, not the
lvds-encoder's node. Put in a little no-op bridge of our own so that
our consumers can still find a bridge where they expect.
This also fixes an unintended unregistration and leak of the
panel-bridge on module remove.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 13dfc0540a ("drm/bridge: Refactor out the panel wrapper from the lvds-encoder bri
dge.")
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114191647.22207-1-eric@anholt.net
Support the "cec" optional clock. The documentation already mentions "cec"
optional clock and it is used by several boards, but currently the driver
doesn't enable it, thus preventing cec from working on those boards.
And even worse: a /dev/cecX device will appear for those boards, but it
won't be functioning without configuring this clock.
Changes:
v4:
- Change commit message to stress the importance of this patch
v3:
- Drop useless braces
v2:
- Separate ENOENT errors from others
- Propagate other errors (especially -EPROBE_DEFER)
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171125201844.11353-1-phh@phh.me
If the device tree for a board did not specify a cec clock, then
adv7511_cec_init would return an error, which would cause adv7511_probe()
to fail and thus there is no HDMI output.
There is no need to have adv7511_probe() fail if the CEC initialization
fails, so just change adv7511_cec_init() to a void function. In addition,
adv7511_cec_init() should just return silently if the cec clock isn't
found and show a message for any other errors.
An otherwise correct cleanup patch from Dan Carpenter turned this broken
failure handling into a kernel Oops, so bisection points to commit
7af35b0add ("drm/kirin: Checking for IS_ERR() instead of NULL") rather
than 3b1b975003 ("drm: adv7511/33: add HDMI CEC support").
Based on earlier patches from Arnd and John.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Xinliang Liu <xinliang.liu@linaro.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3345
Link: https://lkft.validation.linaro.org/scheduler/job/48017#L3551
Fixes: 7af35b0add ("drm/kirin: Checking for IS_ERR() instead of NULL")
Fixes: 3b1b975003 ("drm: adv7511/33: add HDMI CEC support")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/9097b2a4-b6b9-5fca-e039-0a17694b1143@xs4all.nl
Appedix F of HDMI 2.0 says that some HDMI sink may fail to switch from
3D to 2D mode in a timely fashion if the source simply stops sending the
HDMI infoframe. The suggested workaround is to keep sending the
infoframe even when strictly not necessary (ie. no VIC and no S3D).
HDMI 1.4 does allow for this behaviour, stating that sending the
infoframe is optional in this case.
The infoframe was first specified in HDMI 1.4, so in theory sinks
predating that may not appreciate us sending an uknown infoframe
their way. To avoid regressions let's try to determine if the sink
supports the infoframe or not. Unfortunately there's no direct way
to do that, so instead we'll just check if we managed to parse any
HDMI 1.4 4k or stereo modes from the EDID, and if so we assume the
sink will accept the infoframe. Also if the EDID contains the HDMI
2.0 HDMI Forum VSDB we can assume the sink is prepared to receive
the infoframe.
v2: Fix getting has_hdmi_infoframe from display_info
Always fail constructing the infoframe if the display
possibly can't handle it
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113170427.4150-3-ville.syrjala@linux.intel.com
If the sink device is in HDMI mode, enable infoframe interrupt in scdt
irq handle function else call start_video function immediately, because
in DVI mode, there is no infoframe interrupt provided.
Rename start_hdmi function to start_video and get rid of the old
start_video function. In start_video, if the sink is DVI and mode is
MHL1 or MHl2, write appropriate values to registers else the path
should remain the same as in HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510224822-7732-1-git-send-email-m.purski@samsung.com
The maximum pixel clock depends on the version of the connected MHL
adapter. Add mode_valid callback to filter out modes with too high pixel
clock to avoid failure in mode_fixup later.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171109102831.19844-1-m.szyprowski@samsung.com
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
drm_add_edid_modes() now fills in the ELD automatically, so the calls to
drm_edid_to_eld() are redundant. Remove them.
All the other places are obvious, but nv50 has detached
drm_edid_to_eld() from the drm_add_edid_modes() call.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0959ca02b983afc9e74dd9acd190ba6e25f21678.1509545641.git.jani.nikula@intel.com
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHL specification defines Remote Control Protocol(RCP) to
send input events between MHL devices.
The driver now recognizes RCP messages and reacts to them
by reporting key events to input subsystem, allowing
a user to control a device using TV remote control.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Sean Young <sean@mess.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503565087-19730-1-git-send-email-m.purski@samsung.com
Add support for HDMI CEC to the drm adv7511/adv7533 drivers.
The CEC registers that we need to use are identical for both drivers,
but they appear at different offsets in the register map.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171007104658.14528-3-hverkuil@xs4all.nl
SiI9234 transmitter converts eTMDS/HDMI signal to MHL 1.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
This patch is based on the code refactored by Tomasz Stanislawski
<t.stanislaws@samsung.com>, which was initially developed by:
Adam Hampson <ahampson@sta.samsung.com>
Erik Gilling <konkers@android.com>
Shankar Bandal <shankar.b@samsung.com>
Dharam Kumar <dharam.kr@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org> [for dt bindings]
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507212431-5801-2-git-send-email-m.purski@samsung.com
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- DP SDP defines (Ville)
- polish for scdc helpers (Thierry Reding)
- fix lifetimes for connector/plane state across crtc changes (Maarten
Lankhorst).
- sparse fixes (Ville+Thierry)
- make legacy kms ioctls all interruptible (Maarten)
- push edid override into the edid helpers (out of probe helpers)
(Jani)
- DP ESI defines for link status (DK)
Driver Changes:
- drm-panel is now in drm-misc!
- minor panel-simple cleanups/refactoring by various folks
- drm_bridge_add cleanup (Inki Dae)
- constify a few i2c_device_id structs (Arvind Yadav)
- More patches from Noralf's fb/gem helper cleanup
- bridge/synopsis: reset fix (Philippe Cornu)
- fix tracepoint include handling in drivers (Thierry)
- rockchip: lvds support (Sandy Huang)
- move sun4i into drm-misc fold (Maxime Ripard)
- sun4i: refactor driver load + support TCON backend/layer muxing
(Chen-Yu Tsai)
- pl111: support more pl11x variants (Linus Walleij)
- bridge/adv7511: robustify probing/edid handling (Lars-Petersen
Clausen)
New hw support:
- S6E63J0X03 panel (Hoegeun Kwon)
- OTM8009A panel (Philippe CORNU)
- Seiko 43WVF1G panel (Marco Franchi)
- tve200 driver (Linus Walleij)
Plus assorted of tiny patches all over, including our first outreachy
patches from applicants for the winter round!
* tag 'drm-misc-next-2017-09-20' of git://anongit.freedesktop.org/git/drm-misc: (101 commits)
drm: add backwards compatibility support for drm_kms_helper.edid_firmware
drm: handle override and firmware EDID at drm_do_get_edid() level
drm/dp: DPCD register defines for link status within ESI field
drm/rockchip: Replace dev_* with DRM_DEV_*
drm/tinydrm: Drop driver registered message
drm/gem-fb-helper: Use debug message on gem lookup failure
drm/imx: Use drm_gem_fb_create() and drm_gem_fb_prepare_fb()
drm/bridge: adv7511: Constify HDMI CODEC platform data
drm/bridge: adv7511: Enable connector polling when no interrupt is specified
drm/bridge: adv7511: Remove private copy of the EDID
drm/bridge: adv7511: Properly update EDID when no EDID was found
drm/crtc: Convert setcrtc ioctl locking to interruptible.
drm/atomic: Convert pageflip ioctl locking to interruptible.
drm/legacy: Convert setplane ioctl locking to interruptible.
drm/legacy: Convert cursor ioctl locking to interruptible.
drm/atomic: Convert atomic ioctl locking to interruptible.
drm/atomic: Prepare drm_modeset_lock infrastructure for interruptible waiting, v2.
drm/tve200: Clean up panel bridging
drm/doc: Update todo.rst
drm/dp/mst: Sideband message transaction to power up/down nodes
...
The HDMI codec platform data is global driver state shared by all
instances. As such it should not be modified (and is not), to make this
explicit declare it as const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-4-lars@metafoo.de
Fall back to polling the connector for connect and disconnect events when
no interrupt is specified. Otherwise these events will not be noticed and
monitor hotplug does not work.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-3-lars@metafoo.de
The adv7511 driver keeps a private copy of the EDID in its driver state
struct. But this copy is only used in adv7511_get_modes() where it is also
retrieved, so there is no need to keep this extra copy around.
If a need to access the EDID elsewhere in the driver ever arises the copy
that is stored in the connector can be used. This copy is accessible
through drm_connector_get_edid().
Note, this patch removes the NULL check of the EDID before passing it to
drm_detect_hdmi_monitor(), but that is fine since the function correctly
handles the case where the EDID is NULL.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-2-lars@metafoo.de
Currently adv7511_get_modes() bails out early when no EDID could be
retrieved. This leaves the previous EDID in place, which is typically not
the intended behavior and might confuse applications. Instead the EDID
should be cleared when no EDID could be retrieved.
All functions that are called after the EDID check handle the case where
the EDID is NULL just fine and exhibit the expected behavior, so just drop
the check.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-1-lars@metafoo.de
Based on patch "Convert drivers to explicit reset API" from Philipp Zabel
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1501593788-21036-4-git-send-email-philippe.cornu@st.com
This patch cleans up the Synopsys mipi dsi register list:
- rename registers according to the Synopsys documentation
(1.30 & 1.31)
- fix typos
- re-order registers for a better coherency
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1501593788-21036-3-git-send-email-philippe.cornu@st.com
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZpRPIAAoJEAx081l5xIa+kCIP/2m2q0jBmCATvXXwrMBH0zNk
4lm9yIfl9pmluJP97aklvkeKF77chhost76+hv+0sQ9ZsJD8koHWv5WyTHEs7Cfn
NpmtGPqYlIZsWNSwW0OFF/XzllgLCVEWa+W/7ryYzPZrSEZr6Ge4HE0qS3LfuLJv
K89amZWHkP5ysPZ1uxRBzHtZfNAhdyjYVTUntCR7gj3DYv3yNdeZu+/epfcWK2w/
Q+ggoy644vX/yzy5L5zCGL/J1BjStDuec7sgAKTlNx4TwBUmp2wsfhEdovQBGFiu
t5PHMajvrBRqSJWDIAZSUfjQzIMSz517J9LWeChU7KtAClNJQJEabbu4CoX4aEmG
UbSzEe0IxnxQ4842jcqQXZ+mevlNIEIBVSNR7dXi17jL3Ts+APQgrYjRJYVk2ipg
uQ9TwkeVVu2WRGyU8iRQrXAZI7+O3p4UnbNPjeG2qACD2Ur7Z3n7b0mhNFPOLzO4
gbIv4D6CcUB/vltl+vhZTW3P50oMCVSq8ScCpY8CGo29mZ5vypj5PTS+W8FsyY3Z
ypyMqWg/DyxKlOoO+aK8EmXuZmgtDR4kb8asltH/S1A0NZkzjrFkKgs10Cp6EjJy
Zz1BWa1KKEpdN6yp+jrbJKjf9MJ7K2RPGv3bxWnCCdNv4j49rk4t3IHqvcihddsd
XXFQB5zE7Pz0ROi/VkXR
=5fxW
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.14 merge window.
I'm sending this early, as my continuing journey into fatherhood is
occurring really soon now, I'm going to be mostly useless for the next
couple of weeks, though I may be able to read email, I doubt I'll be
doing much patch applications or git sending. If anything urgent pops
up I've asked Daniel/Jani/Alex/Sean to try and direct stuff towards
you.
Outside drm changes:
Some rcar-du updates that touch the V4L tree, all acks should be in
place. It adds one export to the radix tree code for new i915 use
case. There are some minor AGP cleanups (don't see that too often).
Changes to the vbox driver in staging to avoid breaking compilation.
Summary:
core:
- Atomic helper fixes
- Atomic UAPI fixes
- Add YCBCR 4:2:0 support
- Drop set_busid hook
- Refactor fb_helper locking
- Remove a bunch of internal APIs
- Add a bunch of better default handlers
- Format modifier/blob plane property added
- More internal header refactoring
- Make more internal API names consistent
- Enhanced syncobj APIs (wait/signal/reset/create signalled)
bridge:
- Add Synopsys Designware MIPI DSI host bridge driver
tiny:
- Add Pervasive Displays RePaper displays
- Add support for LEGO MINDSTORMS EV3 LCD
i915:
- Lots of GEN10/CNL support patches
- drm syncobj support
- Skylake+ watermark refactoring
- GVT vGPU 48-bit ppgtt support
- GVT performance improvements
- NOA change ioctl
- CCS (color compression) scanout support
- GPU reset improvements
amdgpu:
- Initial hugepage support
- BO migration logic rework
- Vega10 improvements
- Powerplay fixes
- Stop reprogramming the MC
- Fixes for ACP audio on stoney
- SR-IOV fixes/improvements
- Command submission overhead improvements
amdkfd:
- Non-dGPU upstreaming patches
- Scratch VA ioctl
- Image tiling modes
- Update PM4 headers for new firmware
- Drop all BUG_ONs.
nouveau:
- GP108 modesetting support.
- Disable MSI on big endian.
vmwgfx:
- Add fence fd support.
msm:
- Runtime PM improvements
exynos:
- NV12MT support
- Refactor KMS drivers
imx-drm:
- Lock scanout channel to improve memory bw
- Cleanups
etnaviv:
- GEM object population fixes
tegra:
- Prep work for Tegra186 support
- PRIME mmap support
sunxi:
- HDMI support improvements
- HDMI CEC support
omapdrm:
- HDMI hotplug IRQ support
- Big driver cleanup
- OMAP5 DSI support
rcar-du:
- vblank fixes
- VSP1 updates
arcgpu:
- Minor fixes
stm:
- Add STM32 DSI controller driver
dw_hdmi:
- Add support for Rockchip RK3399
- HDMI CEC support
atmel-hlcdc:
- Add 8-bit color support
vc4:
- Atomic fixes
- New ioctl to attach a label to a buffer object
- HDMI CEC support
- Allow userspace to dictate rendering order on submit ioctl"
* tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux: (1074 commits)
drm/syncobj: Add a signal ioctl (v3)
drm/syncobj: Add a reset ioctl (v3)
drm/syncobj: Add a syncobj_array_find helper
drm/syncobj: Allow wait for submit and signal behavior (v5)
drm/syncobj: Add a CREATE_SIGNALED flag
drm/syncobj: Add a callback mechanism for replace_fence (v3)
drm/syncobj: add sync obj wait interface. (v8)
i915: Use drm_syncobj_fence_get
drm/syncobj: Add a race-free drm_syncobj_fence_get helper (v2)
drm/syncobj: Rename fence_get to find_fence
drm: kirin: Add mode_valid logic to avoid mode clocks we can't generate
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
...
Function sii8620_mt_read_devcap_reg_recv() used to read array index
from a wrong msg register, which caused writing out of array
bounds. It led to writing on other fields of struct sii8620.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Fixes: e9c6da270 ("drm/bridge/sii8620: add reading device capability
registers")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503311571-25819-1-git-send-email-m.purski@samsung.com
UAPI Changes:
- vc4: Allow userspace to dictate rendering order in submit_cl ioctl (Eric)
Cross-subsystem Changes:
- vboxvideo: One of Cihangir's patches applies to vboxvideo which is maintained
in staging
Core Changes:
- atomic_legacy_backoff is officially killed (Daniel)
- Extract drm_device.h (Daniel)
- Unregister drm device on unplug (Daniel)
- Rename deprecated drm_*_(un)?reference functions to drm_*_{get|put} (Cihangir)
Driver Changes:
- vc4: Error/destroy path cleanups, log level demotion, edid leak (Eric)
- various: Make various drm_*_funcs structs const (Bhumika)
- tinydrm: add support for LEGO MINDSTORMS EV3 LCD (David)
- various: Second half of .dumb_{map_offset|destroy} defaults set (Noralf)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Cihangir Akturk <cakturk@gmail.com>
Cc: David Lechner <david@lechnology.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
* tag 'drm-misc-next-2017-08-16' of git://anongit.freedesktop.org/git/drm-misc: (50 commits)
drm/gem-cma-helper: Remove drm_gem_cma_dumb_map_offset()
drm/virtio: Use the drm_driver.dumb_destroy default
drm/bochs: Use the drm_driver.dumb_destroy default
drm/mgag200: Use the drm_driver.dumb_destroy default
drm/exynos: Use .dumb_map_offset and .dumb_destroy defaults
drm/msm: Use the drm_driver.dumb_destroy default
drm/ast: Use the drm_driver.dumb_destroy default
drm/qxl: Use the drm_driver.dumb_destroy default
drm/udl: Use the drm_driver.dumb_destroy default
drm/cirrus: Use the drm_driver.dumb_destroy default
drm/tegra: Use .dumb_map_offset and .dumb_destroy defaults
drm/gma500: Use .dumb_map_offset and .dumb_destroy defaults
drm/mxsfb: Use .dumb_map_offset and .dumb_destroy defaults
drm/meson: Use .dumb_map_offset and .dumb_destroy defaults
drm/kirin: Use .dumb_map_offset and .dumb_destroy defaults
drm/vc4: Continue the switch to drm_*_put() helpers
drm/vc4: Fix leak of HDMI EDID
dma-buf: fix reservation_object_wait_timeout_rcu to wait correctly v2
dma-buf: add reservation_object_copy_fences (v2)
drm/tinydrm: add support for LEGO MINDSTORMS EV3 LCD
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZkNpUAAoJEHm+PkMAQRiGr68H/2nr8kxpoUhZ7eA5C71waCjh
gnJSevkzJAp+fCb0KfQFAp1qvpmLLle4e6tAxYgTQZg4Z3W5cJJNfxu9TzY5sGuL
o9QUr43XzABepW4e4jhRtZv6dj3K6XruNeDQKXDZTDcc/S8zoiS/Pltq7VgPcAuM
kX+3qsNdUyknngD6b0z9NtJkb0mHKY6J8MpraWRO34egDwsaN/tuhRj0DRQpCoyQ
x/k+hMbc9MB9Dn8cfACo6Omb+r5Rfd7dTBUAju/TnIIgs//9voHba307N7XvLJZg
kWc8MqMQQZXfRZHB0atpDMHyZS/XQRlNPXj76j0+Ud/byODKTFkkazmgTpALvj8=
=CxeU
-----END PGP SIGNATURE-----
Backmerge tag 'v4.13-rc5' into drm-next
Linux 4.13-rc5
There's a really nasty nouveau collision, hopefully someone can take a look
once I pushed this out.
Core Changes:
- dma-buf: Allow multiple sync_files to wrap a single dma-fence (Chris)
Driver Changes:
- rockchip: misc fixes to vop driver from the downstream rockchip tree (Mark)
- Error path cleanups to tc358767 & host1x (Lucas & Paul, respectively)
* tag 'drm-misc-fixes-2017-08-08' of git://anongit.freedesktop.org/git/drm-misc:
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
dma-buf/sync_file: Allow multiple sync_files to wrap a single dma-fence
drm/bridge: tc358767: fix probe without attached output node
Make these const as they are only passed to the function
drm_connector_init and the corresponding argument is of type const.
Done using Coccinelle
@match disable optional_qualifier@
identifier s;
@@
static struct drm_connector_funcs s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
identifier match.s;
expression e1,e2;
position ref.p;
@@
drm_connector_init(e1,e2,&s@p,...)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct drm_connector_funcs s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1502191712-11231-2-git-send-email-bhumirks@gmail.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make these structures const as they are only stored in the funcs field
of drm_bridge structure, which is of type const.
Done using Coccinelle.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1502207650-20029-1-git-send-email-bhumirks@gmail.com
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Currently HDMI 2.0 PHYs do not have a default configuration function.
As *some* of the HDMI 2.0 PHYs have the same register layout as the 3D
PHYs we can provide the same default configuration function for both
and still let user overwrite this with custom configuration function
if needed.
If, for some reason, the PHY is custom or has a register different
register layout then custom configuration function *must* be provided
in order for the system to work correctly. As we prefer the pdata
provided configuration function over the internal one this change
will not make any impact in custom platforms.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Mark Yao <mark.yao@rock-chips.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Heiko Stübner <heiko@sntech.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/185ccf7d4473fa557044732402ca20b3d4007952.1498209896.git.joabreu@synopsys.com
We don't need the CEC engine register definitions, so let's remove them.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802184108.7913-5-hverkuil@xs4all.nl
The video setup path aways sets the clock disable register to a specific
value, which has the effect of disabling the CEC engine. When we add the
CEC driver, this becomes a problem.
Fix this by only setting/clearing the bits that the video path needs to.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/E1dcBha-00088l-DE@rmk-PC.armlinux.org.uk
Add CEC notifier support to the HDMI bridge driver, so that the CEC
part of the IP can receive its physical address.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/E1dcBhV-00088e-8x@rmk-PC.armlinux.org.uk
The output node of the TC358767 is only used if another bridge is chained
behind it. Panels attached to the TC358767 can be detected using the usual
DP AUX probing. This restores the old behavior of ignoring the output if
no endpoint is found.
Fixes: ebc9446135 (drm: convert drivers to use drm_of_find_panel_or_bridge)
CC: stable@vger.kernel.org
Acked-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170710124125.9019-1-l.stach@pengutronix.de
This will let drivers reduce the error cleanup they need, in
particular the "is_panel_bridge" flag.
v2: Slight cleanup of remove function by Andrzej
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170718210510.12229-2-eric@anholt.net
I need this to be able to apply the deferred fbdev setup patches, I
need the relevant prep work that landed through the drm-intel tree.
Also squash in conflict fixup from Laurent Pinchart.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=TGAC
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.13-rc1' of git://people.freedesktop.org/~airlied/linux
Pull more drm updates from Dave Airlie:
"i915, amd and some core fixes + mediatek color support.
Some fixes tree came in since the main pull request for rc1, primarily
i915 and drm-misc and one amd fix. The drm core vblank regression fix
is probably the most important thing.
I've also added the mediatek feature pull, it wasn't that big and
didn't look like it would have any impact outside of mediatek, in fact
it looks to just be a single feature, and some cleanups"
* tag 'drm-fixes-for-v4.13-rc1' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm/i915: Make DP-MST connector info work
drm/i915/gvt: Use fence error from GVT request for workload status
drm/i915/gvt: remove scheduler_mutex in per-engine workload_thread
drm/i915/gvt: Revert "drm/i915/gvt: Fix possible recursive locking issue"
drm/i915/gvt: Audit the command buffer address
drm/i915/gvt: Fix a memory leak in intel_gvt_init_gtt()
drm/rockchip: fix NULL check on devm_kzalloc() return value
drm/i915/fbdev: Check for existence of ifbdev->vma before operations
drm/radeon: Fix eDP for single-display iMac10,1 (v2)
drm/i915: Hold RPM wakelock while initializing OA buffer
drm/i915/cnl: Fix the CURSOR_COEFF_MASK used in DDI Vswing Programming
drm/i915/cfl: Fix Workarounds.
drm/i915: Avoid undefined behaviour of "u32 >> 32"
drm/i915: reintroduce VLV/CHV PFI programming power domain workaround
drm/i915: Fix an error checking test
drm/i915: Disable MSI for all pre-gen5
drm/atomic: Add missing drm_atomic_state_clear to atomic_remove_fb
drm: vblank: Fix vblank timestamp update
drm/i915/gvt: Make function dpy_reg_mmio_readx safe
drm/mediatek: separate color module to fixup error memory reallocation
...
-----BEGIN PGP SIGNATURE-----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=2S5N
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm, I think I've got one later
driver pull for mediatek SoC driver, I'm undecided on if it needs to
go to you yet.
Otherwise summary below:
Core drm:
- Atomic add driver private objects
- Deprecate preclose hook in modern drivers
- MST bandwidth tracking
- Use kvmalloc in more places
- Add mode_valid hook for crtc/encoder/bridge
- Reduce sync_file construction time
- Documentation updates
- New DRM synchronisation object support
New drivers:
- pl111 - pl111 CLCD display controller
Panel:
- Innolux P079ZCA panel driver
- Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels
- panel-samsung-s6e3ha2: Add s6e3hf2 panel support
i915:
- SKL+ watermark fixes
- G4x/G33 reset improvements
- DP AUX backlight improvements
- Buffer based GuC/host communication
- New getparam for (sub)slice infomation
- Cannonlake and Coffeelake initial patches
- Execbuf optimisations
radeon/amdgpu:
- Lots of Vega10 bug fixes
- Preliminary raven support
- KIQ support for compute rings
- MEC queue management rework
- DCE6 Audio support
- SR-IOV improvements
- Better radeon/amdgpu selection support
nouveau:
- HDMI stereoscopic support
- Display code rework for >= GM20x GPUs
msm:
- GEM rework for fine-grained locking
- Per-process pagetable work
- HDMI fixes for Snapdragon 820.
vc4:
- Remove 256MB CMA limit from vc4
- Add out-fence support
- Add support for cygnus
- Get/set tiling ioctls support
- Add T-format tiling support for scanout
zte:
- add VGA support.
etnaviv:
- Thermal throttle support for newer GPUs
- Restore userspace buffer cache performance
- dma-buf sync fix
stm:
- add stm32f429 display support
exynos:
- Rework vblank handling
- Fixup sw-trigger code
sun4i:
- V3s display engine support
- HDMI support for older SoCs
- Preliminary work on dual-pipeline SoCs.
rcar-du:
- VSP work
imx-drm:
- Remove counter load enable from PRE
- Double read/write reduction flag support
tegra:
- Documentation for the host1x and drm driver.
- Lots of staging ioctl fixes due to grate project work.
omapdrm:
- dma-buf fence support
- TILER rotation fixes"
* tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits)
drm: Remove unused drm_file parameter to drm_syncobj_replace_fence()
drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu.
amdgpu: Set cik/si_support to 1 by default if radeon isn't built
drm/amdgpu/gfx9: fix driver reload with KIQ
drm/amdgpu/gfx8: fix driver reload with KIQ
drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay
drm/ttm: Fix use-after-free in ttm_bo_clean_mm
drm/amd/amdgpu: move get memory type function from early init to sw init
drm/amdgpu/cgs: always set reference clock in mode_info
drm/amdgpu: fix vblank_time when displays are off
drm/amd/powerplay: power value format change for Vega10
drm/amdgpu/gfx9: support the amdgpu.disable_cu option
drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10
drm/amdgpu: Make amdgpu_cs_parser_init static (v2)
drm/amdgpu/cs: fix a typo in a comment
drm/amdgpu: Fix the exported always on CU bitmap
drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static
drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup
drm/amd/powerplay/cz: print message if smc message fails
drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init
...
ALSA SoC needs to know connected DAI ID for probing. Using
the new audio-card-graph approach, ports/endpoints are used
to describe how the links are connected. Unfortunately, since
ports/endpoints are used as well for video linkages, there
are some issues mixing the port ids to the two (video and
audio) namespaces.
To solve this issue, this patch adds new .get_dai_id callback
on hdmi_codec_ops.
The will assume that HDMI audio out will be connected to
reg = <2>. This will then be remapped to the ALSA SoC side will
as DAI 0. Allowing the adv7511's hdmi audio support to be used
with the audio-card-graph.
Credit to Kuninori Morimoto who's patch to dw-hdmi-i2s-audio.c
was what this was mostly copy-pasted from.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Linux-ALSA <alsa-devel@alsa-project.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC needs to know connected DAI ID for probing.
It is not a big problem if device/driver was only for sound,
but getting DAI ID will be difficult if device includes both
Video/Sound, like HDMI.
To solve this issue, this patch adds new .get_dai_id callback
on hdmi_codec_ops.
dw-hdmi-i2s will assume that HDMI sound will be connected
to reg = <2>. Then, ALSA SoC side will recognized it as DAI 0
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
/* HDMI Video IN */
};
port@1 {
reg = <1>;
/* HDMI OUT */
};
port@2 {
reg = <2>;
/* HDMI Sound IN */
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZUGOmAAoJEHm+PkMAQRiGhX8H/3fIhingPD01MBf98U0xGrJo
yIXmhu6nFs7TM0lDVDcHsKgqLQIT69ll7PrSZrMkc1RGUIPINoCuJVuJqDre0kfB
of5TX2KegqSx8h1vOWjGBCBjdYfPGyMdf9icf6KsGc/SlIdhN6WA99kglAjJA0Ve
qPTNagF0ntUNg1lsXffxyfcHqFpyqw/Z/C4ie/byFsn9iJ1VG9mNlTWSud09vhuM
3tvHzTUVAIWWuRrrgrvgqQpnwL+q5BfSDsXScMjBau0EK3RGGqG8EN6Kbkfa7VQ6
aBoeboQjUijSJnVwvySdQ11MChTIOwZdfrNPra/1HD3WJNsSu4BIRt5JcAKcOhc=
=qmSg
-----END PGP SIGNATURE-----
Backmerge tag 'v4.12-rc7' into drm-next
Linux 4.12-rc7
Needed at least rc6 for drm-misc-next-fixes, may as well go to rc7
The dw-hdmi driver switched to regmap-mmio, but lacks the dependency in
Kconfig. This can result in compilation breakages. Fix it by selecting
REGMAP_MMIO.
Fixes: 80e2f97968 ("drm: bridge: dw-hdmi: Switch to regmap for register access")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170610085943.15788-1-laurent.pinchart+renesas@ideasonboard.com
Many DRM drivers have common code to make a stub connector
implementation that wraps a drm_panel. By wrapping the panel in a DRM
bridge, all of the connector code (including calls during encoder
enable/disable) goes away.
v2: Fix build with CONFIG_DRM=m, drop "dev" argument that should just
be the panel's dev, move kerneldoc up a level and document
_remove().
v3: Fix another breakage with CONFIG_DRM=m, fix breakage with
CONFIG_OF=n, move protos under CONFIG_DRM_PANEL_BRIDGE, wrap a
line.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> (v2)
Acked-by: Archit Taneja <architt@codeaurora.org> (v2)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170602202514.11900-1-eric@anholt.net
Now that we have a callback to check if bridge supports a given mode
we can use it in Synopsys Designware HDMI bridge so that we restrict
the number of probbed modes to the ones we can actually display.
Also, there is no need to use mode_fixup() callback as mode_valid()
will handle the mode validation.
NOTE: I also had to change the pdata declaration of mode_valid
custom callback so that the passed modes are const. I also changed
in the platforms I found. Not even compiled it though.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/3d8d449e4d13d2535fa292c75f5fa931de4a4fa8.1495720737.git.joabreu@synopsys.com
Now that we have a callback to check if bridge supports a given mode
we can use it in Analogix bridge so that we restrict the number of
probbed modes to the ones we can actually display.
Also, there is no need to use mode_fixup() callback as mode_valid()
will handle the mode validation.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1d0ed1858ae56c827bd09cc1fa6ff4a05d1530eb.1495720737.git.joabreu@synopsys.com
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, sort the touched parts alphabetically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-7-git-send-email-yamada.masahiro@socionext.com
-----BEGIN PGP SIGNATURE-----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=UxFF
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.12' of git://people.freedesktop.org/~airlied/linux into drm-misc-next
Backmerging Dave's 'drm-for-v4.12' pull request now that it's landed. There are
a bunch of non-drm changes which are just random bits we hadn't yet picked up in
misc-next.
main drm pull request for 4.12 kernel
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/CAPM=9ty0jHgzG18zOr5CYODyTqZfH55kOCOFqNnXiWnTb_uNWw@mail.gmail.com
Currently, the audio sampler clock is enabled from dw_hdmi_setup() at
step E. and is kept enabled for later use. This clock should be enabled
and disabled along with the actual audio stream and not always on (that
is bad for PM). Furthermore, as described by the datasheet, the I2S
variant needs to gate/ungate the clock when the stream is
enabled/disabled.
This commit adds a parameter to hdmi_audio_enable_clk() that controls
when the audio sample clock must be enabled or disabled. Then, it adds
the call to this function from dw_hdmi_i2s_audio_enable() and
dw_hdmi_i2s_audio_disable().
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170414083113.4255-3-romain.perier@collabora.com
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Currently, CTS+N is forced to zero as a workaround of the IP block for
i.MX platforms. This is requested in the datasheet of the corresponding
IP for AHB mode only. However, we have seen that it introduces glitches
or delays when playing a sound on HDMI for I2S mode. This proves that we
cannot keep the current functions for handling audio stream as-is if
these contain workaround that are specific to a mode.
This commit introduces two callbacks, one for each variant.
dw_hdmi_setup defines the right function depending on the detected
variant. Then, the exported functions dw_hdmi_audio_enable and
dw_hdmi_audio_disable calls the corresponding callbacks
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170414083113.4255-2-romain.perier@collabora.com
This helper is supposed to validate or reject the modeline before it
applied by the mode setting. Currently this function has been dropped,
it was previously set to a dummy function that always returned true. For
both cases, this means that userspace can ask for a bad modeline that
will be always accepted.
On some platforms, like Rockchip, the drm dw_hdmi-rockchip variant driver
already implements the atomic_check drm helper, so mode_fixup cannot be
handled and implemented there (as drm_atomic_helper relies on either
atomic_check or mode_fixup).
This commit implements this helper. It only checks that this mode is
correct from the connector point of view.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407121743.4142-1-romain.perier@collabora.com
Normally we do this in drm_mode_config_cleanup. But:
1/ analogix dp's connector is allocated in bind, and freed after unbind.
So we need to destroy it in unbind to avoid further access.
2/ the drm bridge is attached in bind, and detached in encoder cleanup.
So we need to destroy encoder in unbind.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1491481885-13775-5-git-send-email-jeffy.chen@rock-chips.com
The plat_data->input_bus_format and plat_data->input_bus_encoding
are unsigned long and are always >=0, but the value 0 was still
considered as RGB888 for input_bus_format and default color space
for input_bus_encoding in the reworked code.
This patch changes the if statement check for a non-zero value to
either use the default input bus_format and/or bus_encoding for a zero
value and the provided bus_format and/or bus_encoding for a
non zero value.
Thanks to Dan Carpenter for his bug report at [1].
Tested on Amlogic P230 (with CSC enabled for YUV444 to RGB) and Rockchip
RK3288 ACT8846 EVB Board (no CSC involved, direct RGB passthrough).
[1] http://lkml.kernel.org/r/20170406052120.GA26578@mwanda
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: def23aa7e9 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[narmstrong@baylibre.com: reworded commit message and added Fixes tag]
Link: http://patchwork.freedesktop.org/patch/msgid/1491471244-24989-1-git-send-email-narmstrong@baylibre.com
Similar to the previous commit, convert drivers open coding OF graph
parsing to use drm_of_find_panel_or_bridge instead.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul dropped rockchip changes since they're now obsolete]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
There was supposed to be a break before the next case statement.
Fixes: def23aa7e9 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170406052132.GA26605@mwanda
The HDMI TX controller support HPD and RXSENSE signaling from the PHY
via it's STAT0 PHY interface, but some vendor PHYs can manage these
signals independently from the controller, thus these STAT0 handling
should be moved to PHY specific operations and become optional.
The existing STAT0 HPD and RXSENSE handling code is refactored into
a supplementaty set of default PHY operations that are used automatically
when the platform glue doesn't provide its own operations.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491309119-24220-2-git-send-email-narmstrong@baylibre.com
Switch code to use the newly introduced V4L bus formats IDs instead of custom
defines. Also use the V4L encoding defines.
Some display pipelines can only provide non-RBG input pixels to the HDMI TX
Controller, this patch takes the pixel format from the plat_data if provided.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In preparation for adding PHY operations to handle RX SENSE and HPD,
group all the PHY interrupt setup code in a single location and extract
it to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
[narmstrong: renamed dw_hdmi_fb_registered to dw_hdmi_setup_i2c]
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reordering of the device nodes based on unit address resulted in
ge_b850v3_lvds_attach() being called before
ge_b850v3_lvds_ptr->stdp4028_i2c was populated.
This patch moves the drm bridge initialization from
ge_b850v3_lvds_init() to stdp4028_ge_b850v3_fw_probe() ensuring that
ge_b850v3_lvds_ptr->stdp4028_i2c is properly populated.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170330081928.8537-1-peter.senna@collabora.com
On some boards the hpd pin of a hdmi connector is wired up to a gpio
pin. Since in the DRM world the tfp410 driver is responsible for
handling the connector, add support for hpd gpios in this very driver.
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/2e47786ab3d04078ae70d0c4064f7c4d@rwthex-s1-b.rwth-ad.de
Currently, the irq handler that monitors changes for HPD and RX_SENSE
relies on the status of the bridge for updating the status of the HPD.
The update is done only when the bridge is enabled.
However, on Rockchip platforms we have found use cases where it could be
a problem. When HDMI is being used, turning off/on the screen or
unplugging/re-plugging the cable, the following simplified code path
will happen:
- dw_hdmi_irq() will be triggered by an HPD event, as the bridge is on
hdmi->disabled is false, then the handler will update the rxsense flag
accordingly.
- dw_hdmi_update_power() will be invoked with the mode
DRM_FORCE_UNSPECIFIED and rxsense == 1, so dw_hdmi_poweroff() will be
called and the PHY will be desactivated (its pixel clocks and TMDS)
[...]
- dw_hdmi_bridge_disable() will be invoked, the bridge will be marked as
disabled.
- dw_hdmi_irq() will be triggered by an HPD event, as the bridge is
currently disabled the HPD status won't be updated, so hdmi->rxsense
won't be changed. Even if the data part of the PHY is disabled, this
information coming from the HDMI Transmitter is correct and should be
saved.
[...]
- dw_hdmi_bridge_enable() will be invoked, the bridge will be marked as
enabled.
- dw_hdmi_update_power() will be called. When hdmi->force is equal to
DRM_FORCE_UNSPECIFIED the function will rely on hdmi->rxsense. If this
field has not been updated by the irq handler, it will be false and
DRM_FORCE_ON won't be put to hdmi->force.
Consequently, most of the time dw_hdmi_poweron() won't be called in this
use case, TMDS won't be re-enabled the PHY won't be re-initialized,
resulting in a "Signal not found".
This commit fixes the issue by removing the check for "!hdmi->disabled".
As already explained, even if the PHY is partially disabled, information
coming from HDMI Transmitter about HPD should be saved for a later use.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/143602/
"I2C Master Interface Extended Read Mode" implements a segment
pointer-based read operation using the Special Register configuration.
This patch fix https://patchwork.kernel.org/patch/7098101/ mentioned
"The current implementation does not support "I2C Master Interface
Extended Read Mode" to read data addressed by non-zero segment
pointer, this means that if EDID has more than 1 extension blocks,
EDID reading operation won't succeed"
With this patch, dw-hdmi can read EDID data with 1/2/4 blocks.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1489978651-16647-1-git-send-email-nickey.yang@rock-chips.com
The driver is already made of 5 separate source files. Move it to a
newly created directory named synopsys where more Synopsys bridge
drivers can be added later (for the DisplayPort controller for
instance).
Suggested-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-10-laurent.pinchart+renesas@ideasonboard.com
The Synopsys Designware HDMI TX Controller does not enforce register
access on platforms instanciating it. The current driver supports two
different types of memory-mapped flat register access, but in order to
support the Amlogic Meson SoCs integration, and provide a more generic
way to handle all sorts of register mapping, switch the register access
to use the regmap infrastructure.
In the case of registers that are not flat memory-mapped or do not
conform to the current driver implementation, a regmap struct can be
given in the plat_data and be used at probe or bind.
Since the AHB audio driver is only available with direct memory access,
only allow the I2S audio driver to be registered is directly
memory-mapped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-10-laurent.pinchart+renesas@ideasonboard.com
The device type isn't used anymore now that workarounds and PHY-specific
operations are performed based on version information read at runtime.
Remove it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-9-laurent.pinchart+renesas@ideasonboard.com
The DWC HDMI TX controller interfaces with a companion PHY. While
Synopsys provides multiple standard PHYs, SoC vendors can also integrate
a custom PHY.
Modularize PHY configuration to support vendor PHYs through platform
data. The existing PHY configuration code was originally written to
support the DWC HDMI 3D TX PHY, and seems to be compatible with the DWC
MLP PHY. The HDMI 2.0 PHY will require a separate configuration
function.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-8-laurent.pinchart+renesas@ideasonboard.com
The HDMI TX controller support different PHYs whose programming
interface can vary significantly, especially with vendor PHYs that are
not provided by Synopsys. To support them, create a PHY operation
structure that can be provided by the platform glue layer. The existing
PHY handling code (limited to Synopsys PHY support) is refactored into a
set of default PHY operations that are used automatically when the
platform glue doesn't provide its own operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233615.11993-1-laurent.pinchart+renesas@ideasonboard.com
When powering the PHY up we need to wait for the PLL to lock. This is
done by polling the TX_PHY_LOCK bit in the HDMI_PHY_STAT0 register
(interrupt-based wait could be implemented as well but is likely
overkill). The bit is asserted when the PLL locks, but the current code
incorrectly waits for the bit to be deasserted. Fix it, and while at it,
replace the udelay() with a sleep as the code never runs in
non-sleepable context.
To be consistent with the power down implementation move the poll loop
to the power off function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233557.11945-1-laurent.pinchart+renesas@ideasonboard.com
The PHY requires us to wait for the PHY to switch to low power mode
after deasserting TXPWRON and before asserting PDDQ in the power down
sequence, otherwise power down will fail.
The PHY power down can be monitored though the TX_READY bit, available
through I2C in the PHY registers, or the TX_PHY_LOCK bit, available
through the HDMI TX registers. As the two are equivalent, let's pick the
easier solution of polling the TX_PHY_LOCK bit.
The power down code is currently duplicated in multiple places. To avoid
spreading multiple calls to a TX_PHY_LOCK poll function, we have to
refactor the power down code and group it all in a single function.
Tests showed that one poll iteration was enough for TX_PHY_LOCK to
become low, without requiring any additional delay. Retrying the read
five times with a 1ms to 2ms delay between each attempt should thus be
more than enough.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170305233539.11898-1-laurent.pinchart+renesas@ideasonboard.com
If the input pixel format is not RGB, the CSC must be enabled in order to
provide valid pixel to DVI sinks.
This patch removes the hdmi only dependency on the CSC enabling.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-4-laurent.pinchart+renesas@ideasonboard.com
Most of the hdmi_phy_test_*() functions are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-2-laurent.pinchart+renesas@ideasonboard.com
Add two simple functions that just take the drm_dp_aux from our struct
and calls the corresponding DP helpers with it.
v6: Pass to the DP helper the drm_crtc of the current connector (Sean Paul)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-4-tomeu.vizoso@collabora.com
The THC63LVDM83D is a transparent LVDS encoder. Unlike dumb LVDS
encoders it can be controlled through a few pins (power down, LVDS
swing, clock edge selection) and requires power supplies. However, on
several boards where the device is used neither the control pins nor the
power supply are controllable.
To avoid developing a separate device-specific driver add a
"thine,thc63lvdm83d" compatible entry to the lvds-encoder driver. This
will allow supporting many THC63LVDM83D-based boards easily, while
allowing future development of an thc63lvdm83d driver when needed
without breaking backward compatibility.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-5-laurent.pinchart+renesas@ideasonboard.com
The ADV7123 is a transparent VGA DAC. Unlike dumb VGA DACs it can be
controlled through a power save pin, and requires a power supply.
However, on most boards where the device is used neither the power save
signal nor the power supply are controllable.
To avoid developing a separate device-specific driver add an
"adi,adv7123" compatible entry to the dumb-vga-dac driver. This will
allow supporting most ADV7123-based boards easily, while allowing future
development of an adv7123 driver when needed without breaking backward
compatibility.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-4-laurent.pinchart+renesas@ideasonboard.com
The LVDS encoder driver is a DRM bridge driver that supports the
parallel to LVDS encoders that don't require any configuration. The
driver thus doesn't interact with the device, but creates an LVDS
connector for the panel and exposes its size and timing based on
information retrieved from DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-3-laurent.pinchart+renesas@ideasonboard.com
The video processing pipeline on the second output on the GE B850v3:
Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
Each bridge has a dedicated flash containing firmware for supporting the
custom design. The result is that in this design neither the STDP4028
nor the STDP2690 behave as the stock bridges would. The compatible
strings include the suffix "-ge-b850v3-fw" to make it clear that the
driver is for the bridges with the firmware which is specific for the GE
B850v3.
The driver is powerless to control the video processing pipeline, as the
two bridges behaves as a single one. The driver is only needed for
telling the host about EDID / HPD, and for giving the host powers to ack
interrupts.
This driver adds one i2c_device for each bridge, but only one
drm_bridge. This design allows the creation of a functional connector
that is capable of reading EDID from the STDP2690 while handling
interrupts on the STDP4028.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Enric Balletbo <enric.balletbo@collabora.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/ad92919f2eaff2623a551aac94cf11ef948ff9ee.1488555615.git.peter.senna@collabora.com
Fixes the following sparse warning:
drivers/gpu/drm/bridge/ti-tfp410.c:223:24: warning:
symbol 'tfp410_platform_driver' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209152549.30711-1-weiyj.lk@gmail.com
Since all sub-protocols of MHL3 are already supported MHL3 mode can be
enabled. With this patch it is possible to use packed pixel modes and
clocks up to 300MHz - 1920x1080@60Hz and 4K modes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-25-git-send-email-a.hajda@samsung.com
MHL3 protocol requires registry adjustments depending on chosen video mode.
Necessary information is gathered in mode_fixup callback. In case of HDMI
video modes driver should also send special AVI and MHL3 infoframes.
The patch introduces generic helpers for handling MHL3 infoframes, in
case of appearance of other users of MHL3 infoframes these function can
be moved to common library.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-21-git-send-email-a.hajda@samsung.com
The Single-ended eCBUS Mode (eCBUS-S) mode provides 60 Mb/s full-duplex
bidirectional traffic for three channels:
- CBUS data (CBUS1 channel),
- High-bandwidth MHL data (eMSC channel),
- tunneling data (T-CBUS channel).
It is required to fully support MHL3 dongles.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-6-git-send-email-a.hajda@samsung.com
Due to asynchronous nature of MHL flow of execution is dispersed.
Logical continuation of some actions happens after response of peer,
i.e in interrupt handler. To simplify coding continuation mechanism
has been added - it is now possible to provide continuation callback,
which will be called after peer responds to given action.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-5-git-send-email-a.hajda@samsung.com
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
Backmerge Linus master to get the connector locking revert.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
sysctl: fix proc_doulongvec_ms_jiffies_minmax()
Revert "drm/probe-helpers: Drop locking from poll_enable"
MAINTAINERS: add Dan Streetman to zbud maintainers
MAINTAINERS: add Dan Streetman to zswap maintainers
mm: do not export ioremap_page_range symbol for external module
mn10300: fix build error of missing fpu_save()
romfs: use different way to generate fsid for BLOCK or MTD
frv: add missing atomic64 operations
mm, page_alloc: fix premature OOM when racing with cpuset mems update
mm, page_alloc: move cpuset seqcount checking to slowpath
mm, page_alloc: fix fast-path race with cpuset update or removal
mm, page_alloc: fix check for NULL preferred_zone
kernel/panic.c: add missing \n
fbdev: color map copying bounds checking
frv: add atomic64_add_unless()
mm/mempolicy.c: do not put mempolicy before using its nodemask
radix-tree: fix private list warnings
Documentation/filesystems/proc.txt: add VmPin
mm, memcg: do not retry precharge charges
proc: add a schedule point in proc_pid_readdir()
...
The of_node member in struct drm_bridge is hidden when CONFIG_OF
is disabled, causing a build error:
drivers/gpu/drm/bridge/dw-hdmi.c: In function '__dw_hdmi_probe':
drivers/gpu/drm/bridge/dw-hdmi.c:2063:14: error: 'struct drm_bridge' has no member named 'of_node'
We could fix this either using a Kconfig dependency on CONFIG_OF
or making the one line conditional. The latter gives us better
compile test coverage, so this is what I'm doing here.
Fixes: 69497eb923 ("drm: bridge: dw-hdmi: Implement DRM bridge registration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170123122312.3290934-1-arnd@arndb.de
I've found that by just turning the chip on and off via the
POWER_DOWN register, I end up getting i2c_transfer errors on
HiKey.
Investigating further, it turns out that some of the register
state in hardware is getting lost, as the device registers are
reset when the chip is powered down.
Thus this patch simply re-writes the i2c address to the
ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set
before we try to read the EDID data.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org
Thus this patch changes the EDID probing logic so that we
re-use the __adv7511_power_on/off() calls instead of duplciating
logic.
This does change behavior slightly as it adds the HPD signal
pulse to the EDID probe path, but Archit has had a patch to
add HPD signal pulse to the EDID probe path before, so this
should address the cases where that helped. Another difference
is that regcache_mark_dirty() is also called in the power off
path once EDID is probed.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-6-git-send-email-john.stultz@linaro.org
In chasing down issues with EDID probing, I found some
duplicated but incomplete logic used to power the chip on and
off.
This patch refactors the adv7511_power_on/off functions, so
they can be used for internal needs.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-5-git-send-email-john.stultz@linaro.org
On some adv7511 implementations, we can get some spurious
disconnect signals which can cause monitor probing to fail.
This patch enables HPD (hot plug detect) interrupt support
which allows the monitor to be properly re-initialized when
the spurious disconnect signal goes away.
This also enables proper hotplug support.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Originally-by: Archit Taneja <architt@codeaurora.org>
[jstultz: Added proper commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-4-git-send-email-john.stultz@linaro.org
In chasing down a previous issue with EDID probing from calling
drm_helper_hpd_irq_event() from irq context, Laurent noticed
that the DRM documentation suggests that
drm_kms_helper_hotplug_event() should be used instead.
Thus this patch replaces drm_helper_hpd_irq_event() with
drm_kms_helper_hotplug_event(), which requires we update the
connector.status entry and only call _hotplug_event() when the
status changes.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-3-git-send-email-john.stultz@linaro.org
I was recently seeing issues with EDID probing, where
the logic to wait for the EDID read bit to be set by the
IRQ wasn't happening and the code would time out and fail.
Digging deeper, I found this was due to the fact that
IRQs were disabled as we were running in IRQ context from
the HPD signal.
Thus this patch changes the logic to handle the HPD signal
via a work_struct so we can be out of irq context.
With this patch, the EDID probing on hotplug does not time
out.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-2-git-send-email-john.stultz@linaro.org
According to the PHY IP core vendor, the SVSRET signal must be asserted
before resetting the PHY. Tests on RK3288 and R-Car Gen3 showed no
regression, the change should thus be safe.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-20-laurent.pinchart+renesas@ideasonboard.com
The PHY reset signal is controlled by bit PHYRSTZ in the MC_PHYRSTZ
register. The signal is active low on Gen1 PHYs and active high on Gen2
PHYs. The driver toggles the signal high then low, which is correct for
all currently supported platforms, but the register values macros are
incorrectly named. Replace them with a single macro named after the bit,
and add a comment to the source code to explain the behaviour.
The driver's behaviour isn't changed by this rename, the code will still
need to be fixed to support Gen1 PHYs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-19-laurent.pinchart+renesas@ideasonboard.com
Replace the hardcoded register address numerical values with macros to
clarify the code.
This change has been tested by comparing the assembly code before and
after the change.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-18-laurent.pinchart+renesas@ideasonboard.com
Use the device version queried at runtime instead of the device type
provided through platform data to handle the overflow workaround. This
will make support of other SoCs integrating the same HDMI TX controller
version easier.
Among the supported platforms only i.MX6DL and i.MX6Q have been
identified as needing the workaround. Disabling it on Rockchip RK3288
(which integrates a v2.00a controller) didn't produce any error or
artifact.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-16-laurent.pinchart+renesas@ideasonboard.com
Bit 0 in CONFIG1_ID tells whether the IP core uses an AHB slave
interface for control. The correct way to identify AHB audio DMA support
is through bit 1 in CONFIG3_ID.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-15-laurent.pinchart+renesas@ideasonboard.com
The DWC HDMI TX can be recognized by the two product identification
registers. If the registers don't read as expect the IP will be very
different than what the driver has been designed for, or will be
misconfigured in a way that makes it non-operational (invalid memory
address, incorrect clocks, ...). We should reject this situation with an
error.
While this isn't critical for proper operation with supported IPs at the
moment, the driver will soon gain automatic device-specific handling
based on runtime device identification. This change makes it easier to
implement that without having to default to a random guess in case the
device can't be identified.
While at it print a readable version number in the device identification
message instead of raw register values.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-14-laurent.pinchart+renesas@ideasonboard.com
The bit is documented in a Rockchip BSP as
#define m_SVSRET_SIG (1 << 5) /* depend on PHY_MHL_COMB0=1 */
This is confirmed by a Renesas platform, which uses a 2.0 DWC HDMI TX as
the RK3288. Rename the bit accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-13-laurent.pinchart+renesas@ideasonboard.com
The current code hard codes the call of hdmi_phy_configure() to be 8bpp
and provides extraneous error checking to verify that this hardcoded
value is correct. Simplify the implementation by removing the argument.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-12-laurent.pinchart+renesas@ideasonboard.com
As an option for drivers not based on the component framework, register
the bridge with the DRM core with the DRM bridge API. Existing drivers
based on dw_hdmi_bind() and dw_hdmi_unbind() are not affected as those
functions are preserved with their current behaviour.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-11-laurent.pinchart+renesas@ideasonboard.com
The DRM device is not guaranteed by the bridge API to be available
before the attach callback. The driver performs properly at the moment
as it doesn't use the drm_bridge_add() registration method. As this will
be changed later, move connector creation to attach time to ensure
compatibility with the API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-10-laurent.pinchart+renesas@ideasonboard.com
The next commit will reference structures and functions in a way that
currently requires forward declarations. Reorder the functions to avoid
that. No functional change to the code is performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-9-laurent.pinchart+renesas@ideasonboard.com
There's no need to duplicate identical code in multiple drivers (two at
the moment, one more to come soon). Move it to the dw-hdmi core where it
can be shared. If resource allocation ever becomes device-specific later
we'll always have the option of splitting it out again.
While it at pass the platform device to the bind function to avoid
having to cast struct device to struct platform_device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-8-laurent.pinchart+renesas@ideasonboard.com
Hotplug events should only be forwarded to the DRM core by the interrupt
handler when the bridge has been attached, otherwise the DRM device
pointer will be NULL, resulting in a crash.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-7-laurent.pinchart+renesas@ideasonboard.com
The 'prep' parameter passed to hdmi_phy_configure() is useless. It is
hardcoded as 0, and if set, simply prevents the configure function from
executing.
Remove it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-4-laurent.pinchart+renesas@ideasonboard.com
The master argument isn't used. The data argument, a void pointer, is
used by the bind function only where it's cast to a drm_device pointer,
which can easily be obtained from the encoder argument instead. Remove
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-3-laurent.pinchart+renesas@ideasonboard.com
The latter is just an int wrapper around the former void function that
unconditionally returns 0. As the return value is never checked, merge
the two functions into one.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117082910.27023-2-laurent.pinchart+renesas@ideasonboard.com
Maintain a table of regulator names expected by ADV7511 and ADV7533.
Use regulator_bulk_* api to configure these.
Initialize and enable the regulators during probe itself. Controlling
these dynamically is left for later.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1484117547-26417-3-git-send-email-architt@codeaurora.org
Analogix_dp_bind() can be called from component framework, which doesn't
guarantee proper runtime PM state of the device during bind operation,
so ensure that device is runtime active before doing any register access.
This ensures that the power domain, to which DP module belongs, is turned
on. While at it, also fix the unbalanced call to phy_power_on() in
analogix_dp_bind() function.
This patch solves the following kernel oops on Samsung Exynos5250 Snow
board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 75 Comm: kworker/0:2 Not tainted 4.9.0 #1046
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
task: ee272300 task.stack: ee312000
PC is at analogix_dp_enable_sw_function+0x18/0x2c
LR is at analogix_dp_init_dp+0x2c/0x50
...
[<c03fcb38>] (analogix_dp_enable_sw_function) from [<c03fa9c4>] (analogix_dp_init_dp+0x2c/0x50)
[<c03fa9c4>] (analogix_dp_init_dp) from [<c03fab6c>] (analogix_dp_bind+0x184/0x42c)
[<c03fab6c>] (analogix_dp_bind) from [<c03fdb84>] (component_bind_all+0xf0/0x218)
[<c03fdb84>] (component_bind_all) from [<c03ed64c>] (exynos_drm_load+0x134/0x200)
[<c03ed64c>] (exynos_drm_load) from [<c03d5058>] (drm_dev_register+0xa0/0xd0)
[<c03d5058>] (drm_dev_register) from [<c03d66b8>] (drm_platform_init+0x58/0xb0)
[<c03d66b8>] (drm_platform_init) from [<c03fe0c4>] (try_to_bring_up_master+0x14c/0x188)
[<c03fe0c4>] (try_to_bring_up_master) from [<c03fe188>] (component_add+0x88/0x138)
[<c03fe188>] (component_add) from [<c0403a38>] (platform_drv_probe+0x50/0xb0)
[<c0403a38>] (platform_drv_probe) from [<c0402470>] (driver_probe_device+0x1f0/0x2a8)
[<c0402470>] (driver_probe_device) from [<c0400a54>] (bus_for_each_drv+0x44/0x8c)
[<c0400a54>] (bus_for_each_drv) from [<c04021f8>] (__device_attach+0x9c/0x100)
[<c04021f8>] (__device_attach) from [<c04018e8>] (bus_probe_device+0x84/0x8c)
[<c04018e8>] (bus_probe_device) from [<c0401d1c>] (deferred_probe_work_func+0x60/0x8c)
[<c0401d1c>] (deferred_probe_work_func) from [<c012fc14>] (process_one_work+0x120/0x318)
[<c012fc14>] (process_one_work) from [<c012fe34>] (process_scheduled_works+0x28/0x38)
[<c012fe34>] (process_scheduled_works) from [<c0130048>] (worker_thread+0x204/0x4ac)
[<c0130048>] (worker_thread) from [<c01352c4>] (kthread+0xd8/0xf4)
[<c01352c4>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Code: e59035f0 e5935018 f57ff04f e3c55001 (f57ff04e)
---[ end trace 3d1d0d87796de344 ]---
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1483091866-1088-1-git-send-email-m.szyprowski@samsung.com
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
It looks like the BOE panel FW didn't ack the DPCD600 signal from the
host device, this will cause the panel to hang on the startup display.
The root cause is that we use the fast link mode when we enter and
exit PSR, the issue is gone if we switch from the fast link to main
link mode.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481338159-7189-1-git-send-email-wxt@rock-chips.com
THS8135 is a configurable video DAC, but no configuration is actually
necessary to make it work.
For now use the dumb-vga-dac driver to support it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481623759-12786-4-git-send-email-bgolaszewski@baylibre.com
We will ignored PSR setting if panel not support it. So, in this case,
we should return from analogix_dp_enable/disable_psr() without any
error code. Let's retrun 0 instead of -EINVAL when panel not support PSR
in analogix_dp_enable/disable_psr().
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481072253-8917-1-git-send-email-wzz@rock-chips.com
Backmerge v4.9-rc8 to get at
commit e94bd1736f
Author: Michel Dänzer <michel.daenzer@amd.com>
Date: Wed Nov 30 17:30:01 2016 +0900
drm: Don't call drm_for_each_crtc with a non-KMS driver
so I can apply Michel's follow-up patch.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Many drivers (21 to be exact) create connectors that are always
connected (for instance to an LVDS or DSI panel). Instead of forcing
them to implement a dummy .detect() handler, make the callback optional
and consider the connector as always connected in that case.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[seanpaul fixed small conflict in rcar-du/rcar_du_lvdscon.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
ASSR is an optional feature, so it's a valid operating condition for
the display to reject ASSR enable. Demote the warning to the debug
level.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by:Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161130114810.3245-1-l.stach@pengutronix.de
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Fpy
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.10' of https://github.com/jsarha/linux into drm-next
tilcdc changes for v4.10
* tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits)
drm/tilcdc: fix parsing of some DT properties
drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1
drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb()
drm/tilcdc: Load palette at the end of mode_set_nofb()
drm/tilcdc: Add timeout wait for palette loading to complete
drm/tilcdc: Enable palette loading for revision 2 LCDC too
drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable()
drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h
drm/tilcdc: Fix tilcdc_crtc_create() return value handling
drm/tilcdc: implement palette loading for rev1
drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC
drm/tilcdc: Add drm bridge support for attaching drm bridge drivers
drm/bridge: Add ti-tfp410 DVI transmitter driver
dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge
drm/tilcdc: Recover from sync lost error flood by resetting the LCDC
drm/tilcdc: Fix race from forced shutdown of crtc in unload
drm/tilcdc: Use unload to handle initialization failures
drm/tilcdc: Stop using struct drm_driver load() callback
drm/tilcdc: Remove obsolete drm_connector_register() calls
drm/tilcdc: Correct misspelling in error message
...
Add very basic ti-tfp410 DVI transmitter driver. The only feature
separating this from a completely dummy bridge is the EDID read
support trough DDC I2C. Even that functionality should be in a
separate generic connector driver. However, because of missing DRM
infrastructure support the connector is implemented within the bridge
driver. Some tfp410 HW specific features may be added later if needed,
because there is a set of registers behind i2c if it is connected.
This implementation is tested against my new tilcdc bridge support
and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document
is also updated.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
This patch enables the Audio Data and Clock pads to the adv7533 bridge.
Without this patch audio can not be played.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-3-git-send-email-john.stultz@linaro.org
This patch adds support to Audio for both adv7511 and adv7533
bridge chips.
This patch was originally from [1] by Lars-Peter Clausen <lars@metafoo.de>
and was adapted by Archit Taneja <architt@codeaurora.org> and
Srinivas Kandagatla <srinivas.kandagatla@linaro.org>.
Then I heavily reworked it to use the hdmi-codec driver. And also
folded in some audio packet initialization done by Andy Green
<andy.green@linaro.org>. So credit to them, but blame to me.
[1] https://github.com/analogdevicesinc/linux/blob/xcomm_zynq/drivers/gpu/drm/i2c/adv7511_audio.c
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-2-git-send-email-john.stultz@linaro.org
The newly added sound driver depends on SND_SOC_HDMI_CODEC, which in
turn only makes sense when ASoC is enabled, as shown by this warning:
warning: (DRM_MSM && DRM_STI && DRM_MEDIATEK_HDMI && DRM_I2C_NXP_TDA998X && DRM_DW_HDMI_I2S_AUDIO) selects SND_SOC_HDMI_CODEC which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC)
Since the audio driver is probably useless without the audio subsystem,
adding a dependency here seems the right solution.
Fixes: 2761ba6c09 ("drm: bridge: add DesignWare HDMI I2S audio support")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161125205411.1157522-1-arnd@arndb.de
Current dw-hdmi is supporting sound via AHB bus, but it has
I2S audio feature too. This patch adds I2S audio support to dw-hdmi.
This HDMI I2S is supported by using ALSA SoC common HDMI encoder
driver.
Tested-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
Some dumb VGA DACs are active components which require external power.
Add support for specifying a regulator as its power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116154232.872-2-wens@csie.org
Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that were transferred, or a negative error-code on failure. Helpers
propagate errors from the .transfer() function, with the exception of
the -EBUSY error, which causes a transaction to be retried. On a short,
helpers will return -EPROTO to make it simpler to check for failure.
The analogix_dp_transfer will return num_transferred, but if there is none
byte been transferred, the return value will be 0, which means success, we
should return error-code if transfer none byte.
for (retry = 0; retry < 32; retry++) {
err = aux->transfer(aux, &msg);
if (err < 0) {
if (err == -EBUSY)
continue;
goto unlock;
}
}
Cc: zain wang <wzz@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1479255219-7243-1-git-send-email-jay.xu@rock-chips.com
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
-----BEGIN PGP SIGNATURE-----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=aAzo
-----END PGP SIGNATURE-----
Merge tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next
dw-hdmi i2c master controller
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
* tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
drm: bridge/dw_hdmi: add dw hdmi i2c bus adapter support
drm: dw_hdmi: use of_get_i2c_adapter_by_node interface
drivers/gpu/drm/bridge/sil-sii8620.c:1556:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98766@lkp-sb04.lkp.intel.com
SiI8620 transmitter converts eTMDS/HDMI signal to MHL 3.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476085157-5266-1-git-send-email-a.hajda@samsung.com
Drop unneeded drm_connector_unregister() and remove the unnecessary
wrapper functions around drm_connector_cleanup().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161005143133.5549-1-marex@denx.de
Some boards have an entirely passive RGB to VGA bridge, based on DACs
implemented by resistor ladders.
Those might or might not have an i2c bus routed to the VGA connector in
order to access the screen EDIDs.
Add a bridge that doesn't do anything but expose the modes available on the
screen, either based on the EDIDs if available, or based on the XGA
standards.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160930143709.1388-3-maxime.ripard@free-electrons.com
Remove the unnecessary wrapper functions around drm_connector_cleanup().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161004222331.7200-1-marex@denx.de
- more core cleanup patches to prep drm_file to be used for
kernel-internal contexts (David Herrmann)
- more split-up+docs for drm_crtc.c
- lots of small fixes and polish all over
* tag 'topic/drm-misc-2016-09-25' of git://anongit.freedesktop.org/drm-intel: (37 commits)
drm: bridge: analogix/dp: mark symbols static where possible
drm/bochs: mark bochs_connector_get_modes() static
drm/bridge: analogix_dp: Improve panel on time
drm/bridge: analogix_dp: Don't read EDID if panel present
drm/bridge: analogix_dp: Remove duplicated code
Revert "drm/i2c: tda998x: don't register the connector"
drm: Fix plane type uabi breakage
dma-buf/sync_file: free fences array in num_fences is 1
drm/i2c: tda998x: don't register the connector
drm: Don't swallow error codes in drm_dev_alloc()
drm: Distinguish no name from ENOMEM in set_unique()
drm: Remove dirty property from docs
drm/doc: Document color space handling
drm: Extract drm_color_mgmt.[hc]
drm/doc: Polish plane composition property docs
drm: Conslidate blending properties in drm_blend.[hc]
drm/doc: Polish for drm_plane.[hc]
drm: Extract drm_plane.[hc]
drm/tilcdc: Add atomic and crtc headers to crtc.c
drm: Fix typo in encoder docs
...
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1053:5: warning: no previous prototype for 'analogix_dp_get_modes' [-Wmissing-prototypes]
drivers/gpu/drm/bridge/analogix/analogix_dp_core.c:1097:1: warning: no previous prototype for 'analogix_dp_detect' [-Wmissing-prototypes]
In fact, both functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks both functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1474788764-6069-1-git-send-email-baoyou.xie@linaro.org
In order to reduce the time required to turn on the panel, this patch
makes 2 assumptions:
1- In detect(): if there's a panel, we're connected.
2- In get_modes(): if there's a panel, let the panel driver decide if
it should prepare/unprepare in order to get the modes.
The first is straightforward, and shouldn't need further explanation. The
second should eliminate the prepare/unprepare delays from get_modes() in
most cases, since panels generally hardcode their modes in the driver as
opposed to reading EDID. If a panel does need to read EDID, it should be
responsible for ensuring it's in a state in which it can.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
If there's a panel connected to the analogix_dp bridge, rely on
the panel driver for modes, rather than reading EDID *and* calling
get_modes() on the panel.
This allows panels with a valid EDID to read it in the panel driver
(e.g. simple_panel), and panels with invalid EDID to homebrew modes
in their get_modes implementation.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Remove code for reading the EDID and DPCD fields and use the helpers
instead.
Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
- add active plane reconfiguration support (v4),
use the atomic_disable callback
- stop calling disable_plane manually in the plane destroy path
- let mode cleanup destroy mode objects on driver unbind
- drop deprecated load/unload drm_driver ops
- add exclusive fence to plane state, so the atomic helper can
wait on them, remove the open-coded fence wait from imx-drm
- add low level deinterlacer (VDIC) support
- add support for channel linking via the frame synchronisation unit (FSU)
- add queued image conversion support for memory-to-memory scaling, rotation,
and color space conversion, using IC and IRT.
-----BEGIN PGP SIGNATURE-----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=WtaT
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm active plane reconfiguration, cleanup, FSU/IC/IRT/VDIC support
- add active plane reconfiguration support (v4),
use the atomic_disable callback
- stop calling disable_plane manually in the plane destroy path
- let mode cleanup destroy mode objects on driver unbind
- drop deprecated load/unload drm_driver ops
- add exclusive fence to plane state, so the atomic helper can
wait on them, remove the open-coded fence wait from imx-drm
- add low level deinterlacer (VDIC) support
- add support for channel linking via the frame synchronisation unit (FSU)
- add queued image conversion support for memory-to-memory scaling, rotation,
and color space conversion, using IC and IRT.
* tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: Add queued image conversion support
gpu: ipu-v3: Add ipu_rot_mode_is_irt()
gpu: ipu-v3: fix a possible NULL dereference
drm/imx: parallel-display: detach bridge or panel on unbind
drm/imx: imx-ldb: detach bridge on unbind
drm/imx: imx-ldb: detach panel on unbind
gpu: ipu-v3: Add FSU channel linking support
gpu: ipu-v3: Add Video Deinterlacer unit
drm/imx: add exclusive fence to plane state
drm/imx: fold ipu_plane_disable into ipu_disable_plane
drm/imx: don't destroy mode objects manually on driver unbind
drm/imx: drop deprecated load/unload drm_driver ops
drm/imx: don't call disable_plane in plane destroy path
drm/imx: Add active plane reconfiguration support
drm/imx: Use DRM_PLANE_COMMIT_NO_DISABLE_AFTER_MODESET flag
drm/imx: ipuv3-crtc: Use the callback ->atomic_disable instead of ->disable
gpu: ipu-v3: Do not wait for DMFC FIFO to clear when disabling DMFC channel
The change adds support of internal HDMI I2C master controller, this
subdevice is used by default, if "ddc-i2c-bus" DT property is omitted.
The main purpose of this functionality is to support reading EDID from
an HDMI monitor on boards, which don't have an I2C bus connected to
DDC pins.
The current implementation does not support "I2C Master Interface
Extended Read Mode" to read data addressed by non-zero segment
pointer, this means that if EDID has more than 1 extension blocks,
EDID reading operation won't succeed, in my practice all tested HDMI
monitors have at maximum one extension block.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This change is needed to properly lock I2C bus driver, which serves
DDC.
The change fixes an overflow over zero of I2C bus driver user counter:
root@imx6q:~# lsmod
Not tainted
dw_hdmi_ahb_audio 4082 0 - Live 0xbf02c000
dw_hdmi_imx 3498 0 - Live 0xbf00d000
dw_hdmi 16398 2 dw_hdmi_ahb_audio,dw_hdmi_imx, Live 0xbf004000
i2c_imx 16687 0 - Live 0xbf017000
root@imx6q:~# rmmod dw_hdmi_imx
root@imx6q:~# lsmod
Not tainted
dw_hdmi_ahb_audio 4082 0 - Live 0xbf02c000
dw_hdmi 16398 1 dw_hdmi_ahb_audio, Live 0xbf004000
i2c_imx 16687 -1 - Live 0xbf017000
^^
root@imx6q:~# rmmod i2c_imx
rmmod: ERROR: Module i2c_imx is in use
Note that prior to this change put_device() coupled with
of_find_i2c_adapter_by_node() was missing on error path of
dw_hdmi_bind(), added i2c_put_adapter() there along with the change.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Renesas Wheat board has 2 ADV7513 chips on the same I2C bus, however
the ADV751x driver only supports 1 chip as it tries to assign the packet/
EDID/CEC memory I2C devices to the fixed I2C addresses. Assign these I2C
addresses at the fixed offsets (derived from the programming guide) from
the main register map address instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1580212.O1LYdJFM97@wasted.cogentembedded.com
More -misc stuff
- moar drm_crtc.c split up&documentation
- some fixes for the simple kms helpers (Andrea)
- I included all the dri1 patches from David - we're not removing any code
or drivers, and it seems to have worked as a wake-up call to motivate a
few more people to upstream kms conversions for these. Feel free to
revert if you disagree strongly.
- a few other single patches
* tag 'topic/drm-misc-2016-08-31' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm: drm_probe_helper: Fix output_poll_work scheduling
drm: bridge/dw-hdmi: Fix colorspace and scan information registers values
drm/doc: Polish docs for drm_property&drm_property_blob
drm: Unify handling of blob and object properties
drm: Extract drm_property.[hc]
drm: move drm_mode_legacy_fb_format to drm_fourcc.c
drm/doc: Polish docs for drm_mode_object
drm: Remove drm_mode_object->atomic_count
drm: Extract drm_mode_object.[hc]
drm/doc: Polish kerneldoc for encoders
drm: Extract drm_encoder.[hc]
drm/fb-helper: don't call remove_conflicting_framebuffers for FB=m && DRM=y
drm/atomic-helper: Add NO_DISABLE_AFTER_MODESET flag support for plane commit
drm/atomic-helper: Disable appropriate planes in disable_planes_on_crtc()
drm/atomic-helper: Add atomic_disable CRTC helper callback
drm: simple_kms_helper: add support for bridges
drm: simple_kms_helper: make connector optional at init time
drm/bridge: introduce bridge detaching mechanism
drm/simple-helpers: Always add planes to the state update
drm: reduce GETCLIENT to a minimum
...
Colorspace and scan information values were being written in wrong
offsets. This patch corrects this and writes the values at the
offsets specified in the databook.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/96fd0f06b7ebc2ee5cb8239a99648f3107e24497.1471530573.git.joabreu@synopsys.com
Instead let drm_mode_config_cleanup() do the work when taking down
the master device. This requires all cleanup functions to be
properly hooked up to the mode object .destroy callback.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This pull request contains the following rockchip drm changes:
- Introduce support for rk3399 vop/crtc
- Add PSR framework to the rockchip driver
- Implement PSR in the rockchip analogix edp driver
- Fix panel on/off in analogix to avoid damaging panels
- Some miscellaneous fixes to clean up logs and code readability
* 'for-next' of git://people.freedesktop.org/~seanpaul/dogwood:
drm/rockchip: analogix_dp: drop unnecessary probe deferral "error" print
drm/rockchip: Enable vblank without event
drm/rockchip: Improve analogix-dp psr handling
drm/rockchip: A couple small fixes to psr
drm/rockchip: Use a spinlock to protect psr state
drm/rockchip: Don't use a delayed worker for psr state changes
drm/rockchip: Convert psr_list_mutex to spinlock and use it
drm/rockchip: analogix_dp: implement PSR function
drm/bridge: analogix_dp: add the PSR function support
drm/rockchip: add an common abstracted PSR driver
drm/rockchip: vop: export line flag function
drm/bridge: analogix_dp: Ensure the panel is properly prepared/unprepared
dt-bindings: add compatible strings for big/little rockchip vops
dt-bindings: sort Rockchip vop compatible by chip's number
drm/rockchip: vop: add rk3399 vop support
drm/rockchip: vop: introduce VOP_REG_MASK
drm/rockchip: sort registers define by chip's number
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Instead of just preparing the panel on bind, actually prepare/unprepare
during modeset/disable. The panel must be prepared in order to read hpd
status and edid, so we need to keep state around the prepares in order
to ensure we don't accidentally turn the panel off at the wrong time.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
A few more simple fixes that Sean&I collected. There's a bunch of bigger
things on dri-devel, but I think those are all too late for 4.8 really.
I'll try and go collect them after -rc1 for 4.9.
* tag 'topic/drm-misc-2016-07-28' of git://anongit.freedesktop.org/drm-intel:
drm/arm: mali-dp: Fix error return code in malidp_bind()
drm/arm: mali-dp: Remove redundant dev_err call in malidp_bind()
drm/gma500: remove unnecessary stub for fb_ioctl()
apple-gmux: Sphinxify docs
drm/arm: mali-dp: Set crtc.port to the port instead of the endpoint
drm/sti: use new Reset API
drm/etnaviv: Optimize error handling in etnaviv_gem_new_userptr()
drm/etnaviv: Delete unnecessary checks before two function calls
drm/vmwgfx: Delete an unnecessary check before the function call "vfree"
drm/qxl: Delete an unnecessary check before drm_gem_object_unreference_unlocked()
drm/mgag200: Delete an unnecessary check before drm_gem_object_unreference_unlocked()
drm/bridge: ps8622: Delete an unnecessary check before backlight_device_unregister()
GPU-DRM-GMA500: Delete unnecessary checks before two function calls
GPU-DRM-OMAP: Delete unnecessary checks before two function calls
The backlight_device_unregister() function tests whether its argument
is NULL and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/791089e4-201c-ad01-9c3b-f49835765177@users.sourceforge.net
This is an update to the previous drm bridge pull request. The ADV7511
driver's conversion from slave encoder to bridge meant that its users
(the rcar-du kms driver) should use the bridge interface too. This pull
request now also contains a commit that updates the rcar-du's hdmi encoder
interface from slave encoder to bridge.
The other updates are as before:
- Converts the ADV7511 i2c slave encoder driver to a bridge driver.
Adds support for the ADV7533 bridge chip.
- Add bridge driver for TC358767 (DSI/DPI to eDP) encoder chips.
* 'drm_bridge_for_4.8' of https://github.com/boddob/linux:
drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder
drm/bridge: tc358767: Add DPI to eDP bridge driver
dt-bindings: tc358767: add DT documentation
dt-bindings: drm/bridge: Update bindings for ADV7533
drm/bridge: adv7533: Change number of DSI lanes dynamically
drm/bridge: adv7533: Use internal timing generator
drm/bridge: adv7533: Create a MIPI DSI device
drm/bridge: adv7533: Initial support for ADV7533
drm/bridge: adv7511: Fix mutex deadlock when interrupts are disabled
drm/i2c: adv7511: Move to bridge folder
drm/i2c: adv7511: Convert to drm_bridge
Add a drm_bridge driver for the Toshiba TC358767 DPI/DSI to
eDP/DP bridge. Currently only DPI input with 24-bit RGB is
supported.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Please consider merging this tag, which contains the v4 misc fixes and add RK3399 eDP support patches[0] I sent on 2016-06-29, rebased onto v4.7-rc5.
* 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux:
dt-bindings: analogix_dp: rockchip: correct the wrong compatible name
drm/rockchip: analogix_dp: introduce the pclk for grf
drm/bridge: analogix_dp: fix no drm hpd event when panel plug in
drm/rockchip: analogix_dp: update the comments about why need to hardcode VOP output mode
drm/rockchip: analogix_dp: correct the connector display color format and bpc
drm/bridge: analogix_dp: passing the connector as an argument in .get_modes()
drm/rockchip: analogix_dp: make panel detect to an optional action
drm/rockchip: analogix_dp: add rk3399 eDP support
drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting
drm/bridge: analogix_dp: correct the register bit define error in ANALOGIX_DP_PLL_REG_1
drm/rockchip: analogix_dp: split the lcdc select setting into device data
Lower modes on ADV7533 require lower number of DSI lanes for correct
operation. If ADV7533 is being used with 4 DSI lanes, then switch the
lanes to 3 when the target mode's pixel clock is less than 80 Mhz.
Based on patch by Andy Green <andy.green@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
ADV7533 provides an internal timing generator for certain modes that it
can't use the DSI clock directly.
We've observed that HDMI is more stable with the internal timing
generator, especially if there are instabilities in the DSI clock source.
The data spec also seems to recommend the usage of the timing generator
for all modes.
However, on some platforms, it's reported that enabling the timing
generator causes instabilities with the HDMI output.
Create a DT parameter that lets a platform explicitly disable the timing
generator. The timing generator is enabled by default.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
In order to pass DSI specific parameters to the DSI host, we need the
driver to create a mipi_dsi_device DSI device that attaches to the
host.
Use of_graph helpers to get the DSI host DT node. Create a MIPI DSI
device using this host. Finally, attach this device to the DSI host.
Populate DT parameters (number of data lanes for now) that are required
for DSI RX to work correctly. Hardcode few other parameters (rgb,
embedded_sync) for now.
Select DRM_MIPI_DSI config option only when ADV7533 support is enabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
ADV7533 is a DSI to HDMI encoder chip. It is a derivative of ADV7511,
with additional blocks to translate input DSI data to parallel RGB
data. Besides the ADV7511 I2C register map, it has additional registers
that require to be configured to activate the DSI Rx block.
Create a new config that enables ADV7533 support. Use DT compatible
strings to populate the ADV7533 type enum. Add minimal register
configurations belonging to the DSI/CEC register map. Keep the ADV7533
code in a separate file.
Originally worked on by Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
When the adv7511 i2c client doesn't have an interrupt line, we observe a
deadlock on caused by trying to lock drm device's mode_config.mutex twice
in the same context.
Here is the sequence that causes it:
ioctl DRM_IOCTL_MODE_GETCONNECTOR from userspace
drm_mode_getconnector (acquires mode_config mutex)
connector->fill_modes()
drm_helper_probe_single_connector_modes
connector_funcs->get_modes
adv7511_encoder_get_modes
adv7511_get_edid_block
adv7511_irq_process
drm_helper_hpd_irq_event (acquires mode_config mutex again)
In adv7511_irq_process, don't call drm_helper_hpd_irq_event when not
called from the interrupt handler. It doesn't serve any purpose there
anyway.
Signed-off-by: Archit Taneja <architt@codeaurora.org>