In the case of hotplug enabled devices (PCMCIA/PCIeC) the removal of the
hardware can cause an infinite loop in the common sja1000 isr.
Use the already retrieved status register to indicate a possible hardware
removal and double check by reading the mode register in sja1000_is_absent.
Cc: stable@kernel.org [3.2+]
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
WARNING: drivers/net/ethernet/broadcom/built-in.o(.init.text+0x5d): Section mismatch in reference from the function b44_init() to the function .exit.text:b44_pci_exit()
module exits with b44_cleanup()
Signed-off-by: Nikola Pajkovsky <n.pajkovsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->irq is unsigned, so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently shown that vmxnet3 devices on transmit, will drop very small udp
frames consistently. This is due to a regression introduced by commit
39d4a96fd7. This commit attempts to introduce an
optimization to the tx path, indicating that the underlying hardware behaves
optimally when at least 54 bytes of header data are available for direct access.
This causes problems however, if the entire frame is less than 54 bytes long.
The subsequent pskb_may_pull in vmxnet3_parse_and_copy_hdr fails, causing an
error return code, which leads to vmxnet3_tq_xmit dropping the frame.
Fix it by placing a cap on the copy length. For frames longer than 54 bytes, we
do the pull as we normally would. If the frame is shorter than that, copy the
whole frame, but no more. This ensures that we still get the optimization for
qualifying frames, but don't do any damange for frames that are too short.
Also, since I'm unable to do this, it wuold be great if vmware could follow up
this patch with some additional code commentary as to why 54 bytes is an optimal
pull length for a virtual NIC driver. The comment that introduced this was
vague on that. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Max Matveev <mmatveev@redhat.com>
CC: Max Matveev <mmatveev@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There a two different irq variables ks->irq and netdev->irq.
Only ks->irq is set on probe, so disabling irq in ks_start_xmit fails.
This patches remove ks->irq from private data and use only netdev->irq.
Tested on a kernel 3.0 based OMAP4430 SMP Board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/900802
Cc: stable@vger.kernel.org 3.2+
Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.
3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.
This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'poll' was a debugging option, but turning it on these days leads to
kernel panic. Remove it.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix a similar problem as in 72092cc453
and 481a819914 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces netif_rx()
with netif_rx_ni() which has to be used from process/softirq context.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 619c5cb688 (New 7.0 FW: bnx2x, cnic, bnx2i, bnx2fc) added new
sparse warnings.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Vladislav Zolotarov <vladz@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0869b3a4: ixp4xx-eth: use an unique MDIO bus name changed
the MDIO bus name from "0" to "ixp4xx-eth-0", as a result the PHY
name is not longer appropriate and will not match the MDIO bus name
so PHY connection will not succeed, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "d6c25be: mdio-octeon: use an unique MDIO bus name" changed the
octeon MDIO bus name from "0" to "mdio-octeon-0", change the PHY
formatting logic to account for that name change, so that PHY connection
on this bus succeeds.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "391420f7: fec: use an unique MDIO bus name" first modified
the MDIO bus name to include the platform name, then in commit
"a7ed07d5: net: fec: correct phy_name buffer length when init phy_name"
the PHY name formatting was fixed in the case the PHY matches a PHY
driver.
The FEC driver however, also handles the case where we want to attach
to the fixed MDIO bus name, which was previously named "0", and now
"fixed-0". Change the PHY formatting logic to account for that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e617506: bcm63xx_enet: use an unique MDIO bus name introduced
a regression in the PHY connection logic, since the PHY name was formatted
to expect the bus name to be "0" or "1", whereas it is now "bcm63xx-enet-0"
or "bcm63xx-enet-1".
Reported-by: Joel EJC <joel_ejc@yahoofr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d1733f07: cpmac: use an unique MDIO bus name changed the MDIO bus
name from "1" to "cpmac-1", this breaks the PHY connection logic because
the PHY name still uses the old bus names "0" and "1", fix that to
always use the mdio bus id instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80HSAACgkQMUfUDdst+ymFsQCghwKbV9B9z5fgUXYwFQJ/pD2j
GhsAn3J2mhhHN/vtSPQAN9Vu59Xb/tCi
=VZaE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.
To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().
This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.
Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:
...
PID: 25138 TASK: ffff88021e64c440 CPU: 3 COMMAND: "kworker/3:3"
#0 [ffff88021f007760] machine_kexec at ffffffff810226d9
#1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
#2 [ffff88021f0078a0] oops_end at ffffffff813bca78
#3 [ffff88021f0078d0] no_context at ffffffff81029e72
#4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
#5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
#6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
#7 [ffff88021f007b10] page_fault at ffffffff813bc045
[exception RIP: sysfs_find_dirent+17]
RIP: ffffffff81178611 RSP: ffff88021f007bc0 RFLAGS: 00010246
RAX: ffff88021e64c440 RBX: ffffffff8156cc63 RCX: 0000000000000004
RDX: ffffffff8156cc63 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88021f007be0 R8: 0000000000000004 R9: 0000000000000008
R10: ffffffff816fed00 R11: 0000000000000004 R12: 0000000000000000
R13: ffffffff8156cc63 R14: 0000000000000000 R15: ffff8802222a0000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
#9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K. Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated. As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.
To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than. This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This bug exists in 3.2 stable as well as 3.3 release candidates.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This is applicable to 3.2+ kernels.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit d5bc77a223 broke Wake-on-LAN by
inadvertently dropping the enabling of DMA receives.
Restore the enabling of DMA receives for WoL.
This is applicable to 3.1+ stable trees.
CC: stable@vger.stable.org
Reported-by: Tobias Klausmann <klausman@schwarzvogel.de>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Tobias Klausmann <klausman@schwarzvogel.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that
zd1211 firmware messes up duration_id field if it is not set to zero by driver.
Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits
14 and 15 set and other bits appearing random. Setting duration_id at driver to
zero results zd1211 outputting sane duration_id. This means that firmware is
setting correct values itself and expects duration_id to be zero in first
place.
Looking at vendor driver shows that only PSPoll frames have duration_id set by
driver, for other frames duration_id left zero.
Original bug-report and attached patch at:
http://sourceforge.net/mailarchive/message.php?msg_id=28759111
Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz>
[modified original patch from bug-report, added check for pspoll frame]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
8<----------------------------------------------------------------------
From: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Date: Wed, 16 Nov 2011 09:33:50 +0100
Subject: [PATCH] net: enable TC35815 for MIPS again
TX493[8,9] MIPS SoCs support 2 Ethernet channels of type TC35815
which are connected to the internal PCI controller.
And JMR3927 MIPS board has a TC35815 chip on board.
These dependencies were lost on movement to drivers/net/ethernet/toshiba.
Signed-off-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: stable@vger.kernel.org [3.2+]
Signed-off-by: David S. Miller <davem@davemloft.net>
When this GETHER controller received a large frame (about 1800 bytes
or more), skb_over_panic() happened. This is because the previous
driver set the RFLR to 0x1000 (4096 bytes) and the skb allocate size
is smaller than 4096 bytes. So, the controller accepted such a frame.
The controller can discard a large frame by the RFLR setting.
So, the patch modifies the value of RFLR to mtu + ETH_HLEN +
VLAN_HLEN + ETH_FCS_LEN.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate memory for 'new_data' with kmalloc(). If we get the memory
we then try to build_skb() and if that should fail (which it can) we
do not enter 'if (likely(skb)) {' and actually use 'new_data' but
instead fall through to the 'drop:' label and end up returning from
the function without ever assigning 'new'data' to anything or freeing
it. That leaks the memory allocated to 'new_data'.
This patch fixes the memory leak by doing a kfree(new_data) in the
case where build_skb() fails (or where allocation of 'new_data' itself
fails, but in taht case it's just a harmless kfree(NULL)).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, with PCI/ISA/MCA/CCW all set to n and PCMCIA set to m
setting TR to y will set LLC to m, with very unpleasant results -
net/802/psnap gets picked into obj-y, resulting in the kernel
that won't link - psnap calls functions from llc. The cause,
AFAICS, is that kconfig gets rev_dep for LLC containing
|| TR && (deps for TR)
and even though TR is boolean, both LLC and PCMCIA are tristate
and that thing becomes || y && (n || m), i.e. || m. The reason
for dependency on PCMCIA is that when none of PCI, ISA, MCA, CCW
or PCMCIA is set there'll be no tokenring drivers, so there's no
point building tokenring core. Proper fix probably belongs in
kconfig (we need strict and, such that y <strict_and> m would be
y, so that rev_deps added for tristate selected by bool would
use that instead of &&; we'd have || TR <strict_and> (deps for TR)
in this case), but it's a rather intrusive change. There's an
easy workaround in case of TR -> LLC select, namely to have a def_bool y
symbol sitting under if TR and have that symbol selecting LLC.
Kudos to johill for suggesting that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by several people...
The code in rx_clean was panic'ing so revert
commit d0249e4443.
Will redo DMA mapping checks as new patches for a later release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_prepare_rx_desc does not correctly clean up after it finds an
allocation failure. It should unmap a page before calling put_page, but
it only calls the later.
This bug would prevent a device removal using hotplug after setting the
device MTU to 9000 and opening the network interface. After the fix, we
still see the allocation failure with MTU 9000, but we are able to
remove the device.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After opening the network interface, Mellanox ConnectX device cannot be
removed by hotplug because it has not properly unmapped all DMA memory.
It happens that mlx4_en_activate_rx_rings overrides the variable that
keeps the size of the memory mapped.
This is fixed by passing to mlx4_en_destroy_rx_ring the same size that is
given to mlx4_en_create_rx_ring.
After applying this patch, hot unplugging the device works after opening
the interface.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform cleanup also in non-master flow.
The VFs use communication channel as well.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Laurent Bonnans <bonnans.l@gmail.com>
Reported-by: Jurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver load is failed, sometimes few pointers may remain
uninitialized ex. priv->wdev, priv->netdev, adapter->sleep_cfm
This will cause NULL pointer dereferance while unloading the
driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initially diagnosed on Ubuntu 11.04 with kernel 2.6.38.
velocity_close is not called during a suspend / resume cycle in this
driver and it has no business playing directly with power states.
Signed-off-by: David Lv <DavidLv@viatech.com.cn>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
all works need to be initialized before ieee80211_register_hw
to prevent mac80211 call backs such as drv_start, drv_config
getting started. otherwise we would queue/cancel works before
initializing them and it leads to kernel panic.
this issue can be recreated with the following script
in Chrome laptops with AR928X cards, with background scan
running (or) Network manager is running
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
EIP: [<81040a47>] __cancel_work_timer+0xb8/0xe1 SS:ESP 0068:f6be9d70
---[ end trace 4f86d6139a9900ef ]---
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf88a0000,
irq=16
Kernel panic - not syncing: Fatal exception
Pid: 456, comm: wpa_supplicant Tainted: G D
3.0.13 #1
Call Trace:
[<81379e21>] panic+0x53/0x14a
[<81004a30>] oops_end+0x73/0x81
[<81004b53>] die+0x4c/0x55
[<81002710>] do_trap+0x7c/0x83
[<81002855>] ? do_bounds+0x58/0x58
[<810028cc>] do_invalid_op+0x77/0x81
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810489ec>] ? sched_clock_cpu+0x81/0x11f
[<8103f809>] ? wait_on_work+0xe2/0xf7
[<8137f807>] error_code+0x67/0x6c
[<810300d8>] ? wait_consider_task+0x4ba/0x84c
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810380c9>] ? try_to_del_timer_sync+0x5f/0x67
[<81040a91>] cancel_work_sync+0xf/0x11
[<f88d7b7c>] ath_set_channel+0x62/0x25c [ath9k]
[<f88d67d1>] ? ath9k_tx_last_beacon+0x26a/0x85c [ath9k]
[<f88d8899>] ath_radio_disable+0x3f1/0x68e [ath9k]
[<f90d0edb>] ieee80211_hw_config+0x111/0x116 [mac80211]
[<f90dd95c>] __ieee80211_recalc_idle+0x919/0xa37 [mac80211]
[<f90dda76>] __ieee80211_recalc_idle+0xa33/0xa37 [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently even if association is failed "iw link" shows some
information about connected BSS and "Tx timeout" error is seen in
dmesg log.
This patch fixes below issues in the code to handle assoc failure
case correctly.
1) "status" variable in mwifiex_wait_queue_complete() is not
correctly updated. Hence driver doesn't inform cfg80211 stack
about association failure.
2) During association network queues are stopped but carrier is
not cleared, which gives Tx timeout error in failure case
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct spelling "packtetbuf_num" to "packetbuf_num" in
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Change copyright date to 2012 in the source files.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove jump to out label that was skipping over code to replace the
ack bit in the mailbox cache variable. This was causing driver mailbox
routines that poll for the PF to ack a message to time out which would
in turn cause all other mailbox messages to fail. Also replace the
mailbox cache variable message indication bit when a message is found
so that other functions that choose to poll for a mailbox message from
the PF won't miss it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Send message to system log when the VF requests another MAC filter
but there is no space left on the device for it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New year so bump the copyright date.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the way channels objects are linked together by peak_pci_probe()
avoiding any kernel oops when driver is removed. Side effect is that
the list is now browsed from last to first channel.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
netif_device_attched is called twice when ems_usb_start fails with -ENODEV
Signed-off-by: Sebastian Haas <dev@sebastianhaas.info>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The test (((errc & PCH_REC) >> 8) > 127) would always be false because
the receive error counter ((errc & PCH_REC) >> 8) is at most 127, where
PCH_REC is defined as 0x7f00. To test whether the receive error counter
has reached the error passive level, the RP bit (15) should be used.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes locking problems by using netif_rx() instead of
netif_receive_skb() in ti_hecc_error() called from the interrupt
context.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fix avoids a deadlock if an interrupt occurs
during consecutive port operations on ISA cards
utilising indirect access via address and data
port.
Tested on a B&R ISA card.
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wolfgang Zarre <lkdev@essax.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On slow systems and high CAN bitrates, the error message
"can_put_echo_skb: BUG! echo_skb is occupied!" did show up because
can_put_echo_skb() was called after starting the transfer.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As pointed out by Reuben Dowle and Lothar Waßmann, the TWRN_INT,
RWRN_INT, BOFF_INT interrupt sources need to be cleared as well
to avoid interrupt flooding, at least for the Flexcan on i.MX28
SOCs. Furthermore, the interrupts are only cleared, if really one
of those interrupt sources are pending (which is not the case for
rx and tx done).
Cc: Reuben Dowle <Reuben.Dowle@navico.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is a possible data corruption if an RNDIS message goes beyond page
boundary in the sending code path. This patch fixes the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For code path not on the xmit, use netif_tx_disable() instead of
netif_stop_queue() to ensure other CPUs are not doing xmit.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ERR should be called before its argument is cleared.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
constant c;
@@
*e = c
... when != e = e1
when != &e
when != true IS_ERR(e)
*PTR_ERR(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packets with size larger than 1452 will be dropped by bridge
which with two hyperv netdevice ports. This cause by hyperv netvsc
driver always copy the trailer padding to the data packet, and then
the skb received from netdevice may include wrong skb->len (20 bytes
larger than the real size normally). The captured packet may like
this:
Ethernet II, Src: Microsof_00:00:07 (00:15:5d:00:00:07),
Dst: HewlettP_00:00:4e (00:1f:29:00:00:4e)
Destination: HewlettP_e6:00:4e (00:1f:29:00:00:4e)
Source: Microsof_f6:6d:07 (00:15:5d:f6:6d:07)
Type: IP (0x0800)
Trailer: 1415161718191A1B1C1D1E1F20212223
Frame check sequence: 0x24252627 [incorrect, should be 0x7c2e5a5e]
The following command help to reproduction it, and the ping ICMP
packets will be dropped by bridge.
$ ping ip -s 1453
This patch fixed it by removing the trailer padding from the data
packet.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my AMPDU rework, I rely on the sequence numbers of frames. But
I didn't check that the frame has a valid tid before updating the
tracking counters. As a result, the Tx queues were stalled. People
who hit this bug saw that we simply didn't let any data out.
This bug was introduced in 3.3.
This patch fixes that and checks that the frame is a QoS frame before
looking at its tid and changing the counters.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch correct the type of variables containing the rssi
values read from the rxwi.
In function rt2800_agc_to_rssi() 3 variables (rssi0, rssi1, rss2)
defined as int was assigned a 16bit signed values as unsigned.
From a test with a hi-gain antenna I verified that the rxwi
contains signed rssi values in the range -13/+81 (inclusive)
with 0 as an error condition. In case of negative values a
condition is triggered and the function return -128dBm while
the signal is at its maximum. This patch correct the cast so
negative values are not treated as very high positive values
(ex. -13 does not become 243).
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The parameters for ETHTOOL_FLASHDEV include a filename, which ought to
be null-terminated. Currently the only driver that implements
ethtool_ops::flash_device attempts to add a null terminator if
necessary, but does it wrongly. Do it in the ethtool core instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->len after call eth_type_trans() does not include the ether
header size, but rx_bytes should account it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the bug that we got wrong phy_name on imx6q sabrelite board.
snprintf used wrong length of phy_name.
phy_name length is MII_BUS_ID_SIZE + 3 rather not MII_BUS_ID_SIZE.
I change it to sizeof(phy_name).
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MISC_DEVICES option alone does not select any kernel code and can cause dependency build warnings, such as:
warning: (KS8851 && AX88796_93CX6 && RTL8180 && RTL8187 && ADM8211 && RT2400PCI && RT2500PCI && RT61PCI && RT2800PCI && R8187SE) selects EEPROM_93CX6 which has unmet direct dependencies (MISC_DEVICES)
As the current drivers/misc/Kconfig stands, it is only possible to select the drivers below if MISC_DEVICES option is selected:
source "drivers/misc/c2port/Kconfig"
source "drivers/misc/eeprom/Kconfig"
source "drivers/misc/cb710/Kconfig"
source "drivers/misc/iwmc3200top/Kconfig"
source "drivers/misc/ti-st/Kconfig"
source "drivers/misc/lis3lv02d/Kconfig"
source "drivers/misc/carma/Kconfig"
source "drivers/misc/altera-stapl/Kconfig"
So remove MISC_DEVICES option so that nothing is dependant on it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes event message behaviour to send only updated records
instead of whole list. This fixes bug on which userspace receives non-actual
data in case multiple events occur in row.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
do_set_multicast() may not free the memory malloc in
netvsc_set_multicast_list().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An implicit instance of module.h leaked back into existence
and was masking the fact that these drivers weren't calling
out the include for itself. Fix the drivers before we remove
the implicit include path via net/netprio_cgroup.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STM has a device ID within its own VENDOR space, and it is being
used in the STA2X11 I/O Hub.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit "db8857b stmmac: use an unique MDIO bus name" my
device stopped being probed because two different names were being
used in different places. This fixes the inconsistency.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Florian Fainelli <florian@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interrupt comes in, we read the reason
bits and collect them into "trans_pcie->inta".
This happens with the spinlock held. However,
there's a bug resetting this variable -- that
happens after the spinlock has been released.
This means that it is possible for interrupts
to be missed if the reset happens after some
other interrupt reasons were already added to
the variable.
I found this by code inspection, looking for a
reason that we sometimes see random commands
time out. It seems possible that this causes
such behaviour, but I can't say for sure right
now since it happens extremely infrequently on
my test systems.
Cc: stable@vger.kernel.org [3.2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add reporting of silicon revision during the probe function for Marvell 88E6123/88E6161/88E6165 switches.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head
doesnt include any payload data.
if (skb_is_gso_v6(skb))
hdr_len = skb_headlen(skb) - ETH_HLEN;
This is not true anymore after commit f07d960df3 (tcp: avoid frag
allocation for small frames)
We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb)
Its also true for IPv4
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also changes the cleanup logic slightly to aggregate
completed notifications for multiple packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These statistics helped me a lot while searching who is losing
packets in my setup.
I added these stats to MIB group since they are very similar,
but just in other registers.
I have tested this patch on 88F6281 SoC.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville