Here are tiny and assorted serial driver fixes that have been in a
branch in my tree for a while and somehow did not get properly merged
into my big TTY / Serial pull request for 3.14-rc1. Sorry about that.
All have been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLm74UACgkQMUfUDdst+ylviACcC4eubO3yOgJzG5A69+Ncl7t6
sy0An2Kb3x0evfvmR6O+fT67rFrvBijA
=Iv/6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are tiny and assorted serial driver fixes that have been in a
branch in my tree for a while and somehow did not get properly merged
into my big TTY / Serial pull request for 3.14-rc1. Sorry about that.
All have been in linux-next for a while with no issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xuartps: Properly guard sysrq specific code
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
serial: icom: dereference after free in load_code()
serial: 8250_dw: add new ACPI IDs
tty: serial: pch: don't crash if DMA enabled but not loaded
serial: samsung: move clock deactivation below uart registration
Pull s390 patches from Martin Schwidefsky:
"A new binary interface to be able to query and modify the LPAR
scheduler weight and cap settings. Some improvements for the hvc
terminal over iucv and a couple of bux fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/hypfs: add interface for diagnose 0x304
s390: wire up sys_sched_setattr/sys_sched_getattr
s390/uapi: fix struct statfs64 definition
s390/uaccess: remove dead extern declarations, make functions static
s390/uaccess: test if current->mm is set before walking page tables
s390/zfcpdump: make zfcpdump depend on 64BIT
s390/32bit: fix cmpxchg64
s390/xpram: don't modify module parameters
s390/zcrypt: remove zcrypt kmsg documentation again
s390/hvc_iucv: Automatically assign free HVC terminal devices
s390/hvc_iucv: Display connection details through device attributes
s390/hvc_iucv: fix sparse warning
s390/vmur: Link parent CCW device during UR device creation
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS4Vf7AAoJEIwa5zzehBx3f9UP/jwMlbfbSZHfNQ/QG0SqZ9RD
zvddyDMHY/qXnzgF3Dax+JR9BDDVy8AlQe713FCoiHJZggWRAbbavkx8gxITDrZQ
6NYaEkkuVxqyM8APl3PwMqYm8UZ8MUf4lCltlOA4jkesY9vue91AFnfyKh2CvHrn
Leg4XT6mFzf/vYDL6RbvTz/Qr253uv3KvYBxkeiRNa0Y7OXRemEXSOfgxh0YGxUl
LZ2IWQFOh/DH4kaeQI8V4G67X3ceHiFyhCnl0CPwfxaZaNBVaxvIFgIUTdetS6Sb
zcXa029tE/Dfsr55vZAv9LUHEipCSOeE5rn2EJWehTWyM7vJ42Eozqgh+zfCjXS7
Ib6g2npsvIluQit/RdITu44h5yZlrQsLgKTGJ8jjXqbT4HQ/746W8b/TP0YLtbw7
N8oqr7k4vsZyF0dAYZQtfQUZeGISz67UbFcdzl9tmYOR7HFuAYkAQYst77zkVJf8
om59BAYYTG5FNjQ4I9AKUfJzxXYveI6AKpXSCCZiahpFM2D1CJIzp9Wi0GwK1HRR
sFVWhS0dajvz63pVVC2tw5Sq4J7onRRNGIXFPoE5fkmlelm0/q0zzGjw3Z0nTqbZ
8zxuwuy2FfPJK11GbUAIhAgn1sCLYyAhl6IE+FsanGeMOSGIMrH0v5/HphAxoCXt
BvqMDogyLoGPce1Gm3pJ
=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Pull audit update from Eric Paris:
"Again we stayed pretty well contained inside the audit system.
Venturing out was fixing a couple of function prototypes which were
inconsistent (didn't hurt anything, but we used the same value as an
int, uint, u32, and I think even a long in a couple of places).
We also made a couple of minor changes to when a couple of LSMs called
the audit system. We hoped to add aarch64 audit support this go
round, but it wasn't ready.
I'm disappearing on vacation on Thursday. I should have internet
access, but it'll be spotty. If anything goes wrong please be sure to
cc rgb@redhat.com. He'll make fixing things his top priority"
* git://git.infradead.org/users/eparis/audit: (50 commits)
audit: whitespace fix in kernel-parameters.txt
audit: fix location of __net_initdata for audit_net_ops
audit: remove pr_info for every network namespace
audit: Modify a set of system calls in audit class definitions
audit: Convert int limit uses to u32
audit: Use more current logging style
audit: Use hex_byte_pack_upper
audit: correct a type mismatch in audit_syscall_exit()
audit: reorder AUDIT_TTY_SET arguments
audit: rework AUDIT_TTY_SET to only grab spin_lock once
audit: remove needless switch in AUDIT_SET
audit: use define's for audit version
audit: documentation of audit= kernel parameter
audit: wait_for_auditd rework for readability
audit: update MAINTAINERS
audit: log task info on feature change
audit: fix incorrect set of audit_sock
audit: print error message when fail to create audit socket
audit: fix dangling keywords in audit_log_set_loginuid() output
audit: log on errors from filter user rules
...
Now that the UART block defines have been moved to a separate file,
include that one and do not longer rely on the MIPS-specific
bcm63xx_regs.h header file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6204/
bcm_{readl,writel} macros expand to __raw_{readl,writel}, use these
directly such that we do not rely on the platform to provide these for
us. As a result, we no longer use bcm63xx_io.h, so remove that inclusion
too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6201/
bcm63xx_irqs.h is included but we are not using anything from it, drop
that include.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6205/
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This was a "forgotten" branch of tty fixes that somehow didn't make it
into my "main" branches, my fault.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the generic "lnxhvc" terminal ID to automatically assign a HVC terminal when
connecting to the HVC IUCV terminal device driver. The terminal device driver
tries to find a free (not connected) HVC terminal to satisfy the incoming
connection request.
With this improvement, you do not longer need to guess which HVC terminal is
free, that is, not connected. Also you can still connect to a particular HVC
terminal by using its associated terminal ID.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add device attributes to display details about the connection status
of HVC IUCV terminals.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
drivers/tty/hvc/hvc_iucv.c:131:25: warning: symbol 'hvc_iucv_get_private' was not
declared. Should it be static?
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Right now the sessionid value in the kernel is a combination of u32,
int, and unsigned int. Just use unsigned int throughout.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Cc: stable <stable@vger.kernel.org> # v3.12
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
prepare and enable the FIFO clock upon PSC FIFO initialization,
check for and propagage errors when enabling the PSC FIFO clock,
disable and unprepare the FIFO clock upon PSC FIFO uninitialization
devm_{get,put}_clk() doesn't apply here, as the SoC provides a
single FIFO component which is shared among several PSC components,
thus the FIFO isn't associated with a device (while the PSCs are)
provide a fallback clock lookup approach in case the OF based clock
lookup for the PSC FIFO fails, this allows for successful operation in
the presence of an outdated device tree which lacks clock specs
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the PSC index,
remove the "psc%d_mclk" template and unconditionally use 'mclk'
acquire and release the "ipg" clock item for register access as well
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
ehv_bytechan is marked tristate but fails to build as a module:
drivers/tty/ehv_bytechan.c:363:1: error: type defaults to ‘int’ in declaration of ‘console_initcall’ [-Werror=implicit-int]
It doesn't make much sense for a console driver to be built as
a module, so change it to a bool.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* qcom/drivers:
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
The msm_serial_hs driver uses mach specific dma APIs. This is not
compatible with the multi-platform ARM effort. Let's only compile
this driver on MSM devices that are prepared to support it;
allowing the DT based MSM devices to enter the multi-platform ARM
build.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rx dma-callback it calls tasklet_schedule, if the tasklet
be scheduled after all the dma-callback in the rx dma channel,
current check condition in the tasklet will not do fetch dma
buffer into tty because tx_issued is equal with tx_completed,
so as timeout tasklet does.
so we check whether we should fetch the whole dma buffer into
tty according to the status of transactions in rx dma channel.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch provides PM entry of uart_ops, then drop clk enable and
disable because serial core will do it.
the patch also fixes the issue that uart hang in resume caused by
not-enabled clock.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions
instead of legacy suspend and resume entries of platform_driver.
this will add hibernation support automatically as suspend to disk
entries are also set.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, read{write}_relaxed() functions was be replaced with
simple read{write}() variants. Potential "uninitialized variable"
warnings was be fixed if driver compiled without MFD_SYSCON.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The four variants of the synclink driver use the same code in their
open() callback to wait for a port in process of being closed,
using interruptible_sleep_on, which is racy and going away soon.
Making things worse, these functions hold the BTM while doing so,
which means that if we ever enter this code path, we cannot actually
continue since the other thread that is in process of closing the
port can no longer get the BTM.
This addresses both issues by using wait_event_interruptible_tty()
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
interruptible_sleep_on is generally problematic and we want to get
rid of it. In case of TIOCMIWAIT, that race is actually in user
space and does not get fixed since we can only detect changes after
entering the ioctl handler, but it removes one more caller.
This instance can not be trivially replaced with wait_event, so
I chose to open-code the wait loop using prepare_to_wait/finish_wait.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=IZCI
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=BQSn
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Second Round of Renesas SH SCI updates for v3.14
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
* tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
Signed-off-by: Olof Johansson <olof@lixom.net>
Updates for the SH SCI serial driver
* Convert to clk_prepare/unprepare
* Fix warnings due to improper casts and printk formats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pxvs
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Renesas SH SCI updates for v3.14
Updates for the SH SCI serial driver
* Convert to clk_prepare/unprepare
* Fix warnings due to improper casts and printk formats
* tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Convert to clk_prepare/unprepare
serial: sh-sci: Don't enable/disable port from within break timer
serial: sh-sci: Fix warnings due to improper casts and printk formats
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Extend the driver to with support for SCIx device tree bindings. A
minimal set of features is supported, additional properties can be added
later should the need to describe more device features arise.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The overrun bit index is a property of the hardware. It's currently
computed based on a different and unrelated hardware property, the baud
rate calculation algorithm. Compute it using hardware identification
information only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IRQ number can't be modified by the user as the port is fixed.
There's no need to check the new IRQ number as it will be ignored by the
core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The base address, IRQ and baud rate generator parent clock rate can't be
changed by userspace. Mark the port as fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver checks if the interrupt number is greater than nr_irqs and
returns an error in that case. The same check is already performed by
the caller, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
there is an overflow in the code :
cyz_polling_cycle = (arg * HZ) / 1000,
the multiplicator arg comes from user, so it may be an overflow if
arg is a big number. And the value of cyc_polling_cycle will be
wrong when it is used next time.
Reported-by: Qixue Xiao <xiaoqixue_1@163.com>
Suggested-by: Yongjian Xu <xuyongjiande@gmail.com>
Suggested-by: Yu Chen <chyyuu@gmail.com>
Signed-off-by: Qixue Xiao <xiaoqixue_1@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This passes the errata fix using a GPIO to control the RTS pin
on one of the AT91 chips to use gpiolib instead of the
AT91-specific interfaces. Also remove the reliance on
compile-time #defines and the cpu_* check and rely on the
platform passing down the proper GPIO pin through platform
data.
This is a prerequisite for getting rid of the local GPIO
implementation in the AT91 platform and move toward
multiplatform.
The patch also adds device tree support for getting the
RTS GPIO pin from the device tree on DT boot paths.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
New driver for NXP (Philips) UART ICs was introduced in September 2012.
Old driver no longer used anywhere, this patch removes it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With block processing of echoed output, observed output order is still
required. Push completed echoes and echo commands prior to output.
Introduce echo_mark echo buffer index, which tracks completed echo
commands; ie., those submitted via commit_echoes but which may not
have been committed. Ensure that completed echoes are output prior
to subsequent terminal writes in process_echoes().
Fixes newline/prompt output order in cooked mode shell.
Cc: <stable@vger.kernel.org> # 3.12.x : 39434ab n_tty: Fix missing newline echo
Reported-by: Karl Dahlke <eklhad@comcast.net>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Karl Dahlke <eklhad@comcast.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark the function hvc_poll_init() as static in hvc/hvc_console.c because
it is not used outside this file.
This eliminates the following warning in hvc/hvc_console.c:
drivers/tty/hvc/hvc_console.c:791:5: warning: no previous prototype for ‘hvc_poll_init’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marks the functions gsm_cleanup_mux(), gsm_activate_mux(),
gsm_free_mux(), gsm_alloc_mux() and gsm_change_mtu() as static in
n_gsm.c because they are not used outside this file.
Also, drop the EXPORT_SYMBOL_GPL for the above mentioned functions
because nothing else in the kernel calls them.
This eliminates the following warnings in n_gsm.c:
drivers/tty/n_gsm.c:2022:6: warning: no previous prototype for ‘gsm_cleanup_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2076:5: warning: no previous prototype for ‘gsm_activate_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2120:6: warning: no previous prototype for ‘gsm_free_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2156:17: warning: no previous prototype for ‘gsm_alloc_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2714:5: warning: no previous prototype for ‘gsm_change_mtu’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back from DMA to interrupt mode the receive interrupt has to
be re-enabled to catch new incoming data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pl011_rx_chars() if pl011_dma_rx_trigger_dma() succeeds it will disable
the receive interrupt, no need to do this again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialisation, a UART may already be in use for a console, so
take care to preserve things like baud rate and data format to avoid
corrupting console output.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to cope with a split tx/rx LCR_H register is non-trivial
so put it into it's own function to avoid duplication.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17438217a6 on request
of Linus Walleij:
Greg can you please drop or revert
commit 17438217a6
"serial: pl011: use DMA RX polling by default"
from the TTY tree until this has been sorted out?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
readline() inadvertently triggers an error recovery path when
pastes larger than 4k overrun the line discipline buffer. The
error recovery path discards input when the line discipline buffer
is full and operating in canonical mode and no newline has been
received. Because readline() changes the termios to non-canonical
mode to read the line char-by-char, the line discipline buffer
can become full, and then when readline() restores termios back
to canonical mode for the caller, the now-full line discipline
buffer triggers the error recovery.
When changing termios from non-canon to canon mode and the read
buffer contains data, simulate an EOF push _without_ the
DISABLED_CHAR in the read buffer.
Importantly for the readline() problem, the termios can be
changed back to non-canonical mode without changes to the read
buffer occurring; ie., as if the previous termios change had not
happened (as long as no intervening read took place).
Preserve existing userspace behavior which allows '\0's already
received in non-canon mode to be read as '\0's in canon mode
(rather than trigger add'l EOF pushes or an actual EOF).
Patch based on original proposal and discussion here
https://bugzilla.kernel.org/show_bug.cgi?id=55991
by Stas Sergeev <stsp@users.sourceforge.net>
Reported-by: Margarita Manterola <margamanterola@gmail.com>
Cc: Maximiliano Curia <maxy@gnuservers.com.ar>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Acked-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a complex patch for refactoring CLPS711X serial driver.
Major changes:
- Eliminate <mach/hardware.h> usage.
- Devicetree support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c49436b657 (serial: 8250_dw: Improve unwritable LCR workaround)
caused a regression. It added a check that the LCR was written properly
to detect and workaround the busy quirk, but the behaviour of bit 5
(UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the
docs. On older versions this caused the check to fail and it would
repeatedly force idle and rewrite the LCR register, causing delays and
preventing any input from serial being received.
This is fixed by masking out UART_LCR_SPAR before making the comparison.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Markus Mayer <markus.mayer@linaro.org>
Tested-by: Tim Kryger <tim.kryger@linaro.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a controlling tty is being hung up and the hang up is
waiting for a just-signalled tty reader or writer to exit, and a new tty
reader/writer tries to acquire an ldisc reference concurrently with the
ldisc reference release from the signalled reader/writer, the hangup
can hang. The new reader/writer is sleeping in ldsem_down_read() and the
hangup is sleeping in ldsem_down_write() [1].
The new reader/writer fails to wakeup the waiting hangup because the
wrong lock count value is checked (the old lock count rather than the new
lock count) to see if the lock is unowned.
Change helper function to return the new lock count if the cmpxchg was
successful; document this behavior.
[1] edited dmesg log from reporter
SysRq : Show Blocked State
task PC stack pid father
systemd D ffff88040c4f0000 0 1 0 0x00000000
ffff88040c49fbe0 0000000000000046 ffff88040c4a0000 ffff88040c49ffd8
00000000001d3980 00000000001d3980 ffff88040c4a0000 ffff88040593d840
ffff88040c49fb40 ffffffff810a4cc0 0000000000000006 0000000000000023
Call Trace:
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff817a6649>] schedule+0x24/0x5e
[<ffffffff817a588b>] schedule_timeout+0x15b/0x1ec
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff817aa691>] ? _raw_spin_unlock_irq+0x24/0x26
[<ffffffff817aa10c>] down_read_failed+0xe3/0x1b9
[<ffffffff817aa26d>] ldsem_down_read+0x8b/0xa5
[<ffffffff8142b5ca>] ? tty_ldisc_ref_wait+0x1b/0x44
[<ffffffff8142b5ca>] tty_ldisc_ref_wait+0x1b/0x44
[<ffffffff81423f5b>] tty_write+0x7d/0x28a
[<ffffffff814241f5>] redirected_tty_write+0x8d/0x98
[<ffffffff81424168>] ? tty_write+0x28a/0x28a
[<ffffffff8115d03f>] do_loop_readv_writev+0x56/0x79
[<ffffffff8115e604>] do_readv_writev+0x1b0/0x1ff
[<ffffffff8116ea0b>] ? do_vfs_ioctl+0x32a/0x489
[<ffffffff81167d9d>] ? final_putname+0x1d/0x3a
[<ffffffff8115e6c7>] vfs_writev+0x2e/0x49
[<ffffffff8115e7d3>] SyS_writev+0x47/0xaa
[<ffffffff817ab822>] system_call_fastpath+0x16/0x1b
bash D ffffffff81c104c0 0 5469 5302 0x00000082
ffff8800cf817ac0 0000000000000046 ffff8804086b22a0 ffff8800cf817fd8
00000000001d3980 00000000001d3980 ffff8804086b22a0 ffff8800cf817a48
000000000000b9a0 ffff8800cf817a78 ffffffff81004675 ffff8800cf817a44
Call Trace:
[<ffffffff81004675>] ? dump_trace+0x165/0x29c
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff8100edda>] ? save_stack_trace+0x26/0x41
[<ffffffff817a6649>] schedule+0x24/0x5e
[<ffffffff817a588b>] schedule_timeout+0x15b/0x1ec
[<ffffffff810a4cc0>] ? sched_clock_cpu+0x9f/0xe4
[<ffffffff817a9f03>] ? down_write_failed+0xa3/0x1c9
[<ffffffff817aa691>] ? _raw_spin_unlock_irq+0x24/0x26
[<ffffffff817a9f0b>] down_write_failed+0xab/0x1c9
[<ffffffff817aa300>] ldsem_down_write+0x79/0xb1
[<ffffffff817aada3>] ? tty_ldisc_lock_pair_timeout+0xa5/0xd9
[<ffffffff817aada3>] tty_ldisc_lock_pair_timeout+0xa5/0xd9
[<ffffffff8142bf33>] tty_ldisc_hangup+0xc4/0x218
[<ffffffff81423ab3>] __tty_hangup+0x2e2/0x3ed
[<ffffffff81424a76>] disassociate_ctty+0x63/0x226
[<ffffffff81078aa7>] do_exit+0x79f/0xa11
[<ffffffff81086bdb>] ? get_signal_to_deliver+0x206/0x62f
[<ffffffff810b4bfb>] ? lock_release_holdtime.part.8+0xf/0x16e
[<ffffffff81079b05>] do_group_exit+0x47/0xb5
[<ffffffff81086c16>] get_signal_to_deliver+0x241/0x62f
[<ffffffff810020a7>] do_signal+0x43/0x59d
[<ffffffff810f2af7>] ? __audit_syscall_exit+0x21a/0x2a8
[<ffffffff810b4bfb>] ? lock_release_holdtime.part.8+0xf/0x16e
[<ffffffff81002655>] do_notify_resume+0x54/0x6c
[<ffffffff817abaf8>] int_signal+0x12/0x17
Reported-by: Sami Farin <sami.farin@gmail.com>
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By using dma_request_slave_channel_or_err(), the DMA slave ID can be
looked up from standard DT properties, and squirrelled away during
channel allocation. Hence, there's no need to use a custom DT property
to store the slave ID.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
tty flip buffers use GFP_ATOMIC allocations for received data
which is to be processed by the line discipline. For each byte
received, an extra byte is used to indicate the error status of
that byte.
Instead, if the received data is error-free, encode the entire
buffer without status bytes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use "fw" in the next line after we release it. I've shifted the call
to release_firmware() down a couple lines to fix this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if the DMA driver isn't loaded "on time" then we crash in the irq handler:
| pch_uart 0000:02:0a.4: pch_request_dma:dma_request_channel FAILS(Tx)
| BUG: unable to handle kernel NULL pointer dereference at (null)
| IP: [<c0676ed9>] pch_uart_interrupt+0x739/0x940
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 60e9357547 (serial: samsung: enable clock before clearing pending
interrupts during init) added handling of the controller clock during init.
On most systems this clock is also one of the baud_clock sources and
possibly used by the earlycon and thus already enabled by the bootloader.
Therefore a gap exists between s3c24xx_serial_init_port disabling the
clock and an attached console reenabling it, making the transition from
earlycon to regular console possibly hang the system - as seen on my
S3C2442 based Freerunner today.
Therefore move the disabling of the clock from s3c24xx_serial_init_port
below the uart port registration, effectively creating an overlap and
keeping the clock running non-stop if the console wants to grab this port.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d7a68be4f2,
'tty: Only perform flip buffer flush from tty_buffer_flush()',
removed buffer flushing from flush_to_ldisc().
Fix function header comment which describes the former behavior.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making DMA RX polling optional when DMA is on was just
over-cautious: there is one single system in the kernel tree
using this facility, Ux500 and after some testing I turned
this on also for Ux500, which means it should simply be on
by default if DMA is enabled.
Cc: Jongsung Kim <neidhard.kim@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
(Note: This patch set differs from previous set in that it uses mutex
instead of spin lock to avoid race, so that it avoids sleeping in automic
context)
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are ongoing..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm mutex lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), a tty framework API, this is the
opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no in-tree user of tty_prepare_flip_string_flags(); remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trim up the memory_used field name to mem_used.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow driver to configure its maximum flip buffer memory
consumption/limit. This is necessary for very-high speed line
rates (in excess of 10MB/sec) because the flip buffers can
be saturated before the line discipline has a chance to
throttle the input.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish if caller is n_tty_poll() or n_tty_read(), and
set the read/wakeup threshold accordingly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although n_tty_receive_char_closing() only has one call-site,
let the compiler inline instead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e60d27c4d8,
n_tty: Factor LNEXT processing from per-char i/o path,
mistakenly inlined the non-inline alias, n_tty_receive_char(),
for the inline function, n_tty_receive_char_inline().
As n_tty_receive_char() is intended for slow-path char
processing only, un-inline it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
N_TTY's direct and flow-controlled flavors of the .receive_buf()
method are nearly identical; fold together.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This early amba_ports declaration was introduced by commit c16d51a32 (amba
pl011: workaround for uart registers lockup) for use in the pl011_lockup_wa()
routine. This routine was later removed by commit 4fd0690bb (serial: pl011:
implement workaround for CTS clear event issue).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI now provides stubs for the functions the driver uses.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_set_options() code unconditionally initalizes the spinlock
on the port. This can cause a deadlock in some situations.
One instance that exposed the problem, was when writing to
/sys/module/kgdboc/parameters/kgdboc to use ttyS0 when the console
is already running on ttyS0. If the spinlock is re-initialized
while the lock is held due to output to the console, there
is a deadlock.
Assume the spinlock is initialized if the port is a console.
Signed-off-by: Randy Witt <rewitt@declaratino.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When L_ECHONL is on, newlines are echoed regardless of the L_ECHO
state; if set, ensure accumulated echoes are flushed before finishing
the current input processing and before more output.
Cc: <stable@vger.kernel.org> # 3.12.x
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c284ee2cf1. Turns out
the locking was incorrect.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With multiple, concurrent readers (each waiting to acquire the
atomic_read_lock mutex), a departing reader may mistakenly reset
minimum_to_wake after a new reader has already set a new value.
Protect the minimum_to_wake reset with the atomic_read_lock critical
section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common security idiom is to hangup the current tty (via vhangup())
after forking but before execing a root shell. This hangs up any
existing opens which other processes may have and ensures subsequent
opens have the necessary permissions to open the root shell tty/pty.
Reset the TTY_HUPPED state after the driver has successfully
returned the opened tty (perform the reset while the tty is locked
to avoid racing with concurrent hangups).
Reported-by: Heorhi Valakhanovich <valahanovich@tut.by>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Tested-by: Heorhi Valakhanovich <valahanovich@tut.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Amiga with
"console=ttyS0" on the kernel command line, it crashes with:
Unable to handle kernel access at virtual address 81dff01c
Oops: 00000000
PC: [<001e09a8>] serial_console_write+0xc/0x70
Add the missing platform check to amiserial_console_init() to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Mac with "console=ttyS0"
on the kernel command line, it crashes with:
Unable to handle kernel NULL pointer dereference at virtual address (null)
Oops: 00000000
PC: [<0013ad28>] __pmz_startup+0x32/0x2a0
...
Call Trace: [<002c5d3e>] pmz_console_setup+0x64/0xe4
The normal tty driver doesn't crash, because init_pmz() checks
pmz_ports_count again after calling pmz_probe().
In the serial console initialization path, pmz_console_init() doesn't do
this, causing the driver to crash later.
Add a check for pmz_ports_count to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are not completed..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm spin lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), which is a tty framework api, and
this is the opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9326b047e4 includes a typo
of "8350_core" instead of "8250_core", so correct it.
Fixes kernel bugzilla #60724:
https://bugzilla.kernel.org/show_bug.cgi?id=60724
Reported-by: Christoph Biedl <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the maximum allowable canonical line is specified to
be 255 bytes (MAX_CANON), the practical limit has actually been
the size of the line discipline read buffer (N_TTY_BUF_SIZE == 4096).
Commit 32f13521ca,
n_tty: Line copy to user buffer in canonical mode, limited the
line copy to 4095 bytes. With a completely full line discipline
read buffer and a userspace buffer > 4095, _no_ data was copied,
and the read() syscall returned 0, indicating EOF.
Fix the interval arithmetic to compute the correct number of bytes
to copy to userspace in the range [1..4096].
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cbfd0340ae,
'n_tty: Process echoes in blocks', introduced an error when
consuming the echo buffer tail to prevent buffer overrun, where
the incorrect operation code byte is checked to determine how
far to advance the tail to the next echo byte.
Check the correct byte for the echo operation code byte.
Cc: <stable@vger.kernel.org> # 3.12.x : c476f65 tty: incorrect test of echo_buf() result for ECHO_OP_START
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A departing reader must restart a flush_to_ldisc() worker _before_
the next reader enters the read loop; this is to avoid the new reader
concluding no more i/o is available and prematurely exiting, when the
old reader simply hasn't re-started the worker yet.
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
- SWIOTLB has tracing added when doing bounce buffer.
- Xen ARM/ARM64 can use Xen-SWIOTLB. This work allows Linux to
safely program real devices for DMA operations when running as
a guest on Xen on ARM, without IOMMU support.*1
- xen_raw_printk works with PVHVM guests if needed.
Bug-fixes:
- Make memory ballooning work under HVM with large MMIO region.
- Inform hypervisor of MCFG regions found in ACPI DSDT.
- Remove deprecated IRQF_DISABLED.
- Remove deprecated __cpuinit.
[*1]:
"On arm and arm64 all Xen guests, including dom0, run with second stage
translation enabled. As a consequence when dom0 programs a device for a
DMA operation is going to use (pseudo) physical addresses instead
machine addresses. This work introduces two trees to track physical to
machine and machine to physical mappings of foreign pages. Local pages
are assumed mapped 1:1 (physical address == machine address). It
enables the SWIOTLB-Xen driver on ARM and ARM64, so that Linux can
translate physical addresses to machine addresses for dma operations
when necessary. " (Stefano).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSgS86AAoJEFjIrFwIi8fJpY4H/R2gke1A1p9UvTwbkaDhgPs/
u/mkI6aH+ktgvu5QZNprki660uydtc4Ck7y8leeLGYw+ed1Ys559SJhRc/x8jBYZ
Hh2chnplld0LAjSpdIDTTePArE1xBo4Gz+fT0zc5cVh0leJwOXn92Kx8N5AWD/T3
gwH4Ok4K1dzZBIls7imM2AM/L1xcApcx3Dl/QpNcoePQtR4yLuPWMUbb3LM8pbUY
0B6ZVN4GOhtJ84z8HRKnh4uMnBYmhmky6laTlHVa6L+j1fv7aAPCdNbePjIt/Pvj
HVYB1O/ht73yHw0zGfK6lhoGG8zlu+Q7sgiut9UsGZZfh34+BRKzNTypqJ3ezQo=
=xc43
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"This has tons of fixes and two major features which are concentrated
around the Xen SWIOTLB library.
The short <blurb> is that the tracing facility (just one function) has
been added to SWIOTLB to make it easier to track I/O progress.
Additionally under Xen and ARM (32 & 64) the Xen-SWIOTLB driver
"is used to translate physical to machine and machine to physical
addresses of foreign[guest] pages for DMA operations" (Stefano) when
booting under hardware without proper IOMMU.
There are also bug-fixes, cleanups, compile warning fixes, etc.
The commit times for some of the commits is a bit fresh - that is b/c
we wanted to make sure we have the Ack's from the ARM folks - which
with the string of back-to-back conferences took a bit of time. Rest
assured - the code has been stewing in #linux-next for some time.
Features:
- SWIOTLB has tracing added when doing bounce buffer.
- Xen ARM/ARM64 can use Xen-SWIOTLB. This work allows Linux to
safely program real devices for DMA operations when running as a
guest on Xen on ARM, without IOMMU support. [*1]
- xen_raw_printk works with PVHVM guests if needed.
Bug-fixes:
- Make memory ballooning work under HVM with large MMIO region.
- Inform hypervisor of MCFG regions found in ACPI DSDT.
- Remove deprecated IRQF_DISABLED.
- Remove deprecated __cpuinit.
[*1]:
"On arm and arm64 all Xen guests, including dom0, run with second
stage translation enabled. As a consequence when dom0 programs a
device for a DMA operation is going to use (pseudo) physical
addresses instead machine addresses. This work introduces two trees
to track physical to machine and machine to physical mappings of
foreign pages. Local pages are assumed mapped 1:1 (physical address
== machine address). It enables the SWIOTLB-Xen driver on ARM and
ARM64, so that Linux can translate physical addresses to machine
addresses for dma operations when necessary. " (Stefano)"
* tag 'stable/for-linus-3.13-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (32 commits)
xen/arm: pfn_to_mfn and mfn_to_pfn return the argument if nothing is in the p2m
arm,arm64/include/asm/io.h: define struct bio_vec
swiotlb-xen: missing include dma-direction.h
pci-swiotlb-xen: call pci_request_acs only ifdef CONFIG_PCI
arm: make SWIOTLB available
xen: delete new instances of added __cpuinit
xen/balloon: Set balloon's initial state to number of existing RAM pages
xen/mcfg: Call PHYSDEVOP_pci_mmcfg_reserved for MCFG areas.
xen: remove deprecated IRQF_DISABLED
x86/xen: remove deprecated IRQF_DISABLED
swiotlb-xen: fix error code returned by xen_swiotlb_map_sg_attrs
swiotlb-xen: static inline xen_phys_to_bus, xen_bus_to_phys, xen_virt_to_bus and range_straddles_page_boundary
grant-table: call set_phys_to_machine after mapping grant refs
arm,arm64: do not always merge biovec if we are running on Xen
swiotlb: print a warning when the swiotlb is full
swiotlb-xen: use xen_dma_map/unmap_page, xen_dma_sync_single_for_cpu/device
xen: introduce xen_dma_map/unmap_page and xen_dma_sync_single_for_cpu/device
tracing/events: Fix swiotlb tracepoint creation
swiotlb-xen: use xen_alloc/free_coherent_pages
xen: introduce xen_alloc/free_coherent_pages
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Pull powerpc updates from Benjamin Herrenschmidt:
"The bulk of this is LE updates. One should now be able to build an LE
kernel and even run some things in it.
I'm still sitting on a handful of patches to enable the new ABI that I
*might* still send this merge window around, but due to the
incertainty (they are pretty fresh) I want to keep them separate.
Other notable changes are some infrastructure bits to better handle
PCI pass-through under KVM, some bits and pieces added to the new
PowerNV platform support such as access to the CPU SCOM bus via sysfs,
and support for EEH error handling on PHB3 (Power8 PCIe).
We also grew arch_get_random_long() for both pseries and powernv when
running on P7+ and P8, exploiting the HW rng.
And finally various embedded updates from freescale"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (154 commits)
powerpc: Fix fatal SLB miss when restoring PPR
powerpc/powernv: Reserve the correct PE number
powerpc/powernv: Add PE to its own PELTV
powerpc/powernv: Add support for indirect XSCOM via debugfs
powerpc/scom: Improve debugfs interface
powerpc/scom: Enable 64-bit addresses
powerpc/boot: Properly handle the base "of" boot wrapper
powerpc/bpf: Support MOD operation
powerpc/bpf: Fix DIVWU instruction opcode
of: Move definition of of_find_next_cache_node into common code.
powerpc: Remove big endianness assumption in of_find_next_cache_node
powerpc/tm: Remove interrupt disable in __switch_to()
powerpc: word-at-a-time optimization for 64-bit Little Endian
powerpc/bpf: BPF JIT compiler for 64-bit Little Endian
powerpc: Only save/restore SDR1 if in hypervisor mode
powerpc/pmu: Fix ADB_PMU_LED_IDE dependencies
powerpc/nvram: Fix endian issue when using the partition length
powerpc/nvram: Fix endian issue when reading the NVRAM size
powerpc/nvram: Scan partitions only once
powerpc/mpc512x: remove unnecessary #if
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSWyGgAAoJEHm+PkMAQRiGA8MH/35upHXImoRCsI5uC1qvHJtI
QvQAhDFxoEXbFUKeaYgTfcM8q9FgnqnfjhLf8eYa4Q7tDZeqLXOE8bkI807mSZMl
yECr3jcwlV+zyhV2MP/HdwTjzy25bwxLM3Zy43S7QROrYoMHZYznil/QPfyMATCJ
XLPuXZC1FtuUen89n4BoDIuL8QaVrIR/zLqFklAQcdTcGpLHSOwFtH8gb2WaRLhv
+4IikFRFgTNZiMR5tP0GPc6UH6TVTvRb4QKSqqa7J8OmfAIvOzAUdhqWSPOIwWwt
Z/+JFxFDczAcNmpv4gE6jkgc2vR8CVeHsvh0j61RDSFObBWspwk337CSyUZxYSA=
=w4VQ
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc5' into stable/for-linus-3.13
Linux 3.12-rc5
Because the Stefano branch (for SWIOTLB ARM changes) is based on that.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'v3.12-rc5': (550 commits)
Linux 3.12-rc5
watchdog: sunxi: Fix section mismatch
watchdog: kempld_wdt: Fix bit mask definition
watchdog: ts72xx_wdt: locking bug in ioctl
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
parisc: let probe_kernel_read() capture access to page zero
parisc: optimize variable initialization in do_page_fault
parisc: fix interruption handler to respect pagefault_disable()
parisc: mark parisc_terminate() noreturn and cold.
parisc: remove unused syscall_ipi() function.
parisc: kill SMP single function call interrupt
parisc: Export flush_cache_page() (needed by lustre)
vfs: allow O_PATH file descriptors for fstatfs()
ext4: fix memory leak in xattr
ARC: Ignore ptrace SETREGSET request for synthetic register "stop_pc"
ALSA: hda - Sony VAIO Pro 13 (haswell) now has a working headset jack
ALSA: hda - Add a headset mic model for ALC269 and friends
ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
compiler/gcc4: Add quirk for 'asm goto' miscompilation bug
Revert "i915: Update VGA arbiter support for newer devices"
...
Pull s390 updates from Martin Schwidefsky:
"The bulk of the patches for the 3.13 merge window.
Heiko spent quite a bit of work to improve the code generation for the
kernel. That includes the exploitation of the interlocked-access
facility for the atomics and bitops implementation and the improvement
for the -march and -mtune compiler settings.
Another important change is the removal of the user_mode=home option,
user processes now always run in primary space. The storage keys are
not initialized at system startup any more, with that the storage key
removal work is complete. For the PCI support the hibernation hooks
have been implemented.
And as usual cleanup and fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (62 commits)
s390/scm_blk: fix endless loop for requests != REQ_TYPE_FS
s390/mm,tlb: correct tlb flush on page table upgrade
s390/mm: page_table_realloc returns failure
s390: allow to set gcc -mtune flag
s390/percpu: remove this_cpu_xor() implementation
s390/vtime: correct idle time calculation
s390/time: fix get_tod_clock_ext inline assembly
tty/hvc_iucv: remove redundant NULL check
s390/dasd: Write to profile data area only if it is available
s390: convert use of typedef ctl_table to struct ctl_table
s390/pci: cleanup function information block
s390/pci: remove CONFIG_PCI_DEBUG dependancy
s390/pci: message cleanup
Update default configuration
s390: add a couple of useful defconfigs
s390/percpu: make use of interlocked-access facility 1 instructions
s390/percpu: use generic percpu ops for CONFIG_32BIT
s390/compat: make psw32_user_bits a constant value again
s390: fix handling of runtime instrumentation psw bit
s390: fix save and restore of the floating-point-control register
...
Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xnEACgkQMUfUDdst+ylj1QCfaIzUNuFfzTmyB6K6iZrRNhCc
WPgAnRLkkEpI/3rRo7jKwGQsuIuyybUu
=r149
-----END PGP SIGNATURE-----
Merge tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.13-rc1.
There's some more minor n_tty work here, but nothing like previous
kernel releases. Also some new driver ids, driver updates for new
hardware, and other small things.
All of this has been in linux-next for a while with no issues"
* tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
serial: omap: fix missing comma
serial: sh-sci: Enable the driver on all ARM platforms
serial: mfd: Staticize local symbols
serial: omap: fix a few checkpatch warnings
serial: omap: improve RS-485 performance
mrst_max3110: fix unbalanced IRQ issue during resume
serial: omap: Add support for optional wake-up
serial: sirf: remove duplicate defines
tty: xuartps: Fix build error when COMMON_CLK is not set
tty: xuartps: Fix build error due to missing forward declaration
tty: xuartps: Fix "may be used uninitialized" build warning
serial: 8250_pci: add Pericom PCIe Serial board Support (12d8:7952/4/8) - Chip PI7C9X7952/4/8
tty: xuartps: Update copyright information
tty: xuartps: Implement suspend/resume callbacks
tty: xuartps: Dynamically adjust to input frequency changes
tty: xuartps: Updating set_baud_rate()
tty: xuartps: Force enable the UART in xuartps_console_write
tty: xuartps: support 64 byte FIFO size
tty: xuartps: Add polled mode support for xuartps
tty: xuartps: Implement BREAK detection, add SYSRQ support
...
Renesas ARM platforms are transitioning from single-platform to
multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
COMPILE_TEST.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/tty/serial/mfd.c:296:6: warning: symbol 'hsu_dma_tx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:343:6: warning: symbol 'hsu_dma_start_rx_chan' was not declared. Should it be static?
drivers/tty/serial/mfd.c:389:6: warning: symbol 'hsu_dma_rx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:1186:17: warning: symbol 'serial_hsu_pops' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RS-485 is enabled, make the OMAP UART fire THR interrupts when both
TX FIFO and TX shift register are empty instead of polling the
equivalent status bit. This removes the burst of interrupt requests
seen at every end of transmission.
Also: the comment said that the TX FIFO trigger level was set at 16
characters when it's 32 in reality.
Signed-off-by: Philippe Proulx <philippe.proulx@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During resume, a startup will request_irq again, meantime resume function's
enable_irq will cause unbalanced IRQ issue.
Fix this issue by moving request_irq to probe function.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chen, Jie <jie.d.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent pinctrl-single changes, omaps can treat
wake-up events from deeper idle states as interrupts.
There's a separate "io chain" controller on most omaps
that stays enabled when the device hits off-idle and the
regular interrupt controller is powered off.
Let's add support for the optional second interrupt for
wake-up events. And then serial-omap can manage the
wake-up interrupt from it's runtime PM calls to avoid
spurious interrupts during runtime.
Note that the wake interrupt is board specific as it
uses the UART RX pin, and for omap3, there are six pin
options for UART3 RX pin.
Also Note that the legacy platform based booting handles
the wake-ups in the legacy mux driver and does not need to
pass the wake-up interrupt to the driver.
And finally, to pass the wake-up interrupt in the dts file,
either interrupt-map or the pending interrupts-extended
property needs to be passed. It's probably best to use
interrupts-extended when it's available.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes duplicate defines in drivers/tty/serial/sirfsoc_uart.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock notifiers are only available when CONFIG_COMMON_CLK is enabled.
Hence all notifier related code has to be protected by corresponsing
ifdefs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is enabled and CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
is not, a forward declaration of the uart_driver struct is not
included, leading to a build error due to an undeclared variable.
Fixing this by moving the definition of the struct uart_driver before
the definition of the suspend/resume callbacks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize varibles for which a 'may be used uninitalized' warning is
issued.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make smatch happy and remove this warning:
drivers/tty/hvc/hvc_iucv.c:1320 hvc_iucv_init() info: redundant null check on
hvc_iucv_filter calling kfree()
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Implement suspend and resume callbacks in order to support system
suspend/hibernation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds