Pull timers and timekeeping updates from Thomas Gleixner:
- Core infrastucture work for Y2038 to address the COMPAT interfaces:
+ Add a new Y2038 safe __kernel_timespec and use it in the core
code
+ Introduce config switches which allow to control the various
compat mechanisms
+ Use the new config switch in the posix timer code to control the
32bit compat syscall implementation.
- Prevent bogus selection of CPU local clocksources which causes an
endless reselection loop
- Remove the extra kthread in the clocksource code which has no value
and just adds another level of indirection
- The usual bunch of trivial updates, cleanups and fixlets all over the
place
- More SPDX conversions
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
clocksource/drivers/mxs_timer: Switch to SPDX identifier
clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Remove outdated file path
clocksource/drivers/arc_timer: Add comments about locking while read GFRC
clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
clocksource/drivers/sprd: Fix Kconfig dependency
clocksource: Move inline keyword to the beginning of function declarations
timer_list: Remove unused function pointer typedef
timers: Adjust a kernel-doc comment
tick: Prefer a lower rating device only if it's CPU local device
clocksource: Remove kthread
time: Change nanosleep to safe __kernel_* types
time: Change types to new y2038 safe __kernel_* types
time: Fix get_timespec64() for y2038 safe compat interfaces
time: Add new y2038 safe __kernel_timespec
posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_64BIT_TIME in architectures
compat: Enable compat_get/put_timespec64 always
...
Pull irq updates from Thomas Gleixner:
- Consolidation of softirq pending:
The softirq mask and its accessors/mutators have many implementations
scattered around many architectures. Most do the same things
consisting in a field in a per-cpu struct (often irq_cpustat_t)
accessed through per-cpu ops. We can provide instead a generic
efficient version that most of them can use. In fact s390 is the only
exception because the field is stored in lowcore.
- Support for level!?! triggered MSI (ARM)
Over the past couple of years, we've seen some SoCs coming up with
ways of signalling level interrupts using a new flavor of MSIs, where
the MSI controller uses two distinct messages: one that raises a
virtual line, and one that lowers it. The target MSI controller is in
charge of maintaining the state of the line.
This allows for a much simplified HW signal routing (no need to have
hundreds of discrete lines to signal level interrupts if you already
have a memory bus), but results in a departure from the current idea
the kernel has of MSIs.
- Support for Meson-AXG GPIO irqchip
- Large stm32 irqchip rework (suspend/resume, hierarchical domains)
- More SPDX conversions
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
ARM: dts: stm32: Add exti support for stm32mp157c
pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
irqchip/stm32: Add suspend/resume support for hierarchy domain
irqchip/stm32: Add stm32mp1 support with hierarchy domain
irqchip/stm32: Prepare common functions
irqchip/stm32: Add host and driver data structures
irqchip/stm32: Add suspend support
irqchip/stm32: Add falling pending register support
irqchip/stm32: Checkpatch fix
irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
irqchip/meson-gpio: Add support for Meson-AXG SoCs
dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
dt-bindings: interrupt-controller: Fix the double quotes
softirq/s390: Move default mutators of overwritten softirq mask to s390
softirq/x86: Switch to generic local_softirq_pending() implementation
softirq/sparc: Switch to generic local_softirq_pending() implementation
softirq/powerpc: Switch to generic local_softirq_pending() implementation
softirq/parisc: Switch to generic local_softirq_pending() implementation
softirq/ia64: Switch to generic local_softirq_pending() implementation
...
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----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=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
By default, sparse assumes a 64bit machine when compiled on x86-64
and 32bit when compiled on anything else.
This can of course create all sort of problems for the other archs, like
issuing false warnings ('shift too big (32) for type unsigned long'), or
worse, failing to emit legitimate warnings.
Fix this by adding the -m32/-m64 flag, depending on CONFIG_64BIT,
to CHECKFLAGS in the main Makefile (and so for all archs).
Also, remove the now unneeded -m32/-m64 in arch specific Makefiles.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The kernel depends on macros like __BYTE_ORDER__,
__BIG_ENDIAN__ or __LITTLE_ENDIAN__.
OTOH, sparse doesn't know about the endianness of the kernel and
by default uses the same as the machine on which sparse was built.
Ensure that sparse can predefine the macros corresponding to
how the kernel was configured by adding -m{big,little}-endian
to CHECKFLAGS in the main Makefile (and so for all archs).
Also, remove the equivalent done in arch specific Makefiles.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No other architecture has setup_profiling_timer() in the init section,
thus on parisc we face this section mismatch warning:
Reference from the function devm_device_add_group() to the function .init.text:setup_profiling_timer()
Signed-off-by: Helge Deller <deller@gmx.de>
The 0-DAY kernel test infrastructure reported that inet_put_port() may
reference the find_pa_parent_type() function, so it can't be moved into the
init section.
Fixes: b86db40e1e ("parisc: Move various functions and strings to init section")
Signed-off-by: Helge Deller <deller@gmx.de>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove the ad-hoc implementation, the generic code now allows us not to
reinvent the wheel.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/1525786706-22846-8-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This way we have one central definition of it, and user can select it as
needed. Note that we now also always select it when CONFIG_DMA_API_DEBUG
is select, which fixes some incorrect checks in a few network drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
This way we have one central definition of it, and user can select it as
needed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
This is a follow-up to Deepa's work on the timekeeping system calls,
providing a y2038-safe syscall API for SYSVIPC. It uses a combination
of two strategies:
For sys_msgctl, sys_semctl and sys_shmctl, I do not introduce a completely
new set of replacement system calls, but instead extend the existing
ones to return data in the reserved fields of the normal data structure.
This should be completely transparent to any existing user space, and
only after the 32-bit time_t wraps, it will make a difference in the
returned data.
libc implementations will consequently have to provide their own data
structures when they move to 64-bit time_t, and convert the structures
in user space from the ones returned by the kernel.
In contrast, mq_timedsend, mq_timedreceive and and semtimedop all do
need to change because having a libc redefine the timespec type
breaks the ABI, so with this series there will be two separate entry
points for 32-bit architectures.
There are three cases here:
- little-endian architectures (except powerpc and mips) can use
the normal layout and just cast the data structure to the user space
type that contains 64-bit numbers.
- parisc and sparc can do the same thing with big-endian user space
- little-endian powerpc and most big-endian architectures have
to flip the upper and lower 32-bit halves of the time_t value in memory,
but can otherwise keep using the normal layout
- mips and big-endian xtensa need to be more careful because
they are not consistent in their definitions, and they have to provide
custom libc implementations for the system calls to use 64-bit time_t.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7FX4
-----END PGP SIGNATURE-----
Merge tag 'y2038-ipc' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull 'y2038: IPC system call conversion' from Arnd Bergmann:
"This is a follow-up to Deepa's work on the timekeeping system calls,
providing a y2038-safe syscall API for SYSVIPC. It uses a combination
of two strategies:
For sys_msgctl, sys_semctl and sys_shmctl, I do not introduce a completely
new set of replacement system calls, but instead extend the existing
ones to return data in the reserved fields of the normal data structure.
This should be completely transparent to any existing user space, and
only after the 32-bit time_t wraps, it will make a difference in the
returned data.
libc implementations will consequently have to provide their own data
structures when they move to 64-bit time_t, and convert the structures
in user space from the ones returned by the kernel.
In contrast, mq_timedsend, mq_timedreceive and and semtimedop all do
need to change because having a libc redefine the timespec type
breaks the ABI, so with this series there will be two separate entry
points for 32-bit architectures.
There are three cases here:
- little-endian architectures (except powerpc and mips) can use
the normal layout and just cast the data structure to the user space
type that contains 64-bit numbers.
- parisc and sparc can do the same thing with big-endian user space
- little-endian powerpc and most big-endian architectures have
to flip the upper and lower 32-bit halves of the time_t value in memory,
but can otherwise keep using the normal layout
- mips and big-endian xtensa need to be more careful because
they are not consistent in their definitions, and they have to provide
custom libc implementations for the system calls to use 64-bit time_t."
This was used by the ide, scsi and networking code in the past to
determine if they should bounce payloads. Now that the dma mapping
always have to support dma to all physical memory (thanks to swiotlb
for non-iommu systems) there is no need to this crude hack any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Palmer Dabbelt <palmer@sifive.com> (for riscv)
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Fix three section mismatches:
1) Section mismatch in reference from the function ioread8() to the
function .init.text:pcibios_init_bridge()
2) Section mismatch in reference from the function free_initmem() to the
function .init.text:map_pages()
3) Section mismatch in reference from the function ccio_ioc_init() to
the function .init.text:count_parisc_driver()
Signed-off-by: Helge Deller <deller@gmx.de>
Fix two section mismatches in drivers.c:
1) Section mismatch in reference from the function alloc_tree_node() to
the function .init.text:create_tree_node().
2) Section mismatch in reference from the function walk_native_bus() to
the function .init.text:alloc_pa_dev().
Signed-off-by: Helge Deller <deller@gmx.de>
Filling in struct siginfo before calling force_sig_info a tedious and
error prone process, where once in a great while the wrong fields
are filled out, and siginfo has been inconsistently cleared.
Simplify this process by using the helper force_sig_fault. Which
takes as a parameters all of the information it needs, ensures
all of the fiddly bits of filling in struct siginfo are done properly
and then calls force_sig_info.
In short about a 5 line reduction in code for every time force_sig_info
is called, which makes the calling function clearer.
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In do_page_fault where an mceerr is generated stop and call force_sig_mceerr.
Keeping the mcerr handling logic out of the force_sig_info call below.
This ensures that only and always in the mcerr case is lsb interesting.
This ensures setting set si_lsb in the future won't accidentally
stomp another siginfo field in the non mcerr case.
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The read_persistent_clock() uses a timespec, which is not year 2038 safe
on 32bit systems. On parisc architecture, we have implemented generic
RTC drivers that can be used to compensate the system suspend time, but
the RTC time can not represent the nanosecond resolution, so this patch
just converts to read_persistent_clock64() with timespec64.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
parisc, uses a nonstandard variation of the generic sysvipc
data structures, intended to have the padding moved around
so it can deal with big-endian 32-bit user space that has
64-bit time_t.
Unlike most architectures, parisc actually succeeded in
defining this right for big-endian CPUs, but as everyone else
got it wrong, we just use the same hack everywhere.
This takes just take the same approach here that we have for
the asm-generic headers and adds separate 32-bit fields for the
upper halves of the timestamps, to let libc deal with the mess
in user space.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the first set of system call entry point changes to enable 32-bit
architectures to have variants on both 32-bit and 64-bit time_t. Typically
these system calls take a 'struct timespec' argument, but that structure
is defined in user space by the C library and its layout will change.
The kernel already supports handling the 32-bit time_t on 64-bit
architectures through the CONFIG_COMPAT mechanism. As there are a total
of 51 system calls suffering from this problem, reusing that mechanism
on 32-bit architectures.
We already have patches for most of the remaining system calls, but this
set contains most of the complexity and is best tested. There was one
last-minute regression that prevented it from going into 4.17, but that
is fixed now.
More details from Deepa's patch series description:
Big picture is as per the lwn article:
https://lwn.net/Articles/643234/ [2]
The series is directed at converting posix clock syscalls:
clock_gettime, clock_settime, clock_getres and clock_nanosleep
to use a new data structure __kernel_timespec at syscall boundaries.
__kernel_timespec maintains 64 bit time_t across all execution modes.
vdso will be handled as part of each architecture when they enable
support for 64 bit time_t.
The compat syscalls are repurposed to provide backward compatibility
by using them as native syscalls as well for 32 bit architectures.
They will continue to use timespec at syscall boundaries.
CONFIG_64_BIT_TIME controls whether the syscalls use __kernel_timespec
or timespec at syscall boundaries.
The series does the following:
1. Enable compat syscalls on 32 bit architectures.
2. Add a new __kernel_timespec type to be used as the data structure
for all the new syscalls.
3. Add new config CONFIG_64BIT_TIME(intead of the CONFIG_COMPAT_TIME in
[1] and [2] to switch to new definition of __kernel_timespec. It is
the same as struct timespec otherwise.
4. Add new CONFIG_32BIT_TIME to conditionally compile compat syscalls.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Bch
-----END PGP SIGNATURE-----
Merge tag 'y2038-timekeeping' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground into timers/core
Pull y2038 timekeeping syscall changes from Arnd Bergmann:
This is the first set of system call entry point changes to enable 32-bit
architectures to have variants on both 32-bit and 64-bit time_t. Typically
these system calls take a 'struct timespec' argument, but that structure
is defined in user space by the C library and its layout will change.
The kernel already supports handling the 32-bit time_t on 64-bit
architectures through the CONFIG_COMPAT mechanism. As there are a total
of 51 system calls suffering from this problem, reusing that mechanism
on 32-bit architectures.
We already have patches for most of the remaining system calls, but this
set contains most of the complexity and is best tested. There was one
last-minute regression that prevented it from going into 4.17, but that
is fixed now.
More details from Deepa's patch series description:
Big picture is as per the lwn article:
https://lwn.net/Articles/643234/ [2]
The series is directed at converting posix clock syscalls:
clock_gettime, clock_settime, clock_getres and clock_nanosleep
to use a new data structure __kernel_timespec at syscall boundaries.
__kernel_timespec maintains 64 bit time_t across all execution modes.
vdso will be handled as part of each architecture when they enable
support for 64 bit time_t.
The compat syscalls are repurposed to provide backward compatibility
by using them as native syscalls as well for 32 bit architectures.
They will continue to use timespec at syscall boundaries.
CONFIG_64_BIT_TIME controls whether the syscalls use __kernel_timespec
or timespec at syscall boundaries.
The series does the following:
1. Enable compat syscalls on 32 bit architectures.
2. Add a new __kernel_timespec type to be used as the data structure
for all the new syscalls.
3. Add new config CONFIG_64BIT_TIME(intead of the CONFIG_COMPAT_TIME in
[1] and [2] to switch to new definition of __kernel_timespec. It is
the same as struct timespec otherwise.
4. Add new CONFIG_32BIT_TIME to conditionally compile compat syscalls.
Debian uses "make all" to build the Linux kernel, thus to be able to use
the self-decompressing kernel as default debian kernel we need to make
bzImage the default build target.
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 71d577db01 ("parisc: Switch to generic COMPAT_BINFMT_ELF")
removed the binfmt_elf32.c source file, but missed to drop the object
file from the list of object files the Makefile, which then results in a
build error.
Fixes: 71d577db01 ("parisc: Switch to generic COMPAT_BINFMT_ELF")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull parisc updates from Helge Deller:
- fix panic when halting system via "shutdown -h now"
- drop own coding in favour of generic CONFIG_COMPAT_BINFMT_ELF
implementation
- add FPE_CONDTRAP constant: last outstanding parisc-specific cleanup
for Eric Biedermans siginfo patches
- move some functions to .init and some to .text.hot linker sections
* 'parisc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent panic at system halt
parisc: Switch to generic COMPAT_BINFMT_ELF
parisc: Move cache flush functions into .text.hot section
parisc/signal: Add FPE_CONDTRAP for conditional trap handling
Remove the address_space ->tree_lock and use the xa_lock newly added to
the radix_tree_root. Rename the address_space ->page_tree to ->i_pages,
since we don't really care that it's a tree.
[willy@infradead.org: fix nds32, fs/dax.c]
Link: http://lkml.kernel.org/r/20180406145415.GB20605@bombadil.infradead.orgLink: http://lkml.kernel.org/r/20180313132639.17387-9-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: introduce MAP_FIXED_NOREPLACE", v2.
This has started as a follow up discussion [3][4] resulting in the
runtime failure caused by hardening patch [5] which removes MAP_FIXED
from the elf loader because MAP_FIXED is inherently dangerous as it
might silently clobber an existing underlying mapping (e.g. stack).
The reason for the failure is that some architectures enforce an
alignment for the given address hint without MAP_FIXED used (e.g. for
shared or file backed mappings).
One way around this would be excluding those archs which do alignment
tricks from the hardening [6]. The patch is really trivial but it has
been objected, rightfully so, that this screams for a more generic
solution. We basically want a non-destructive MAP_FIXED.
The first patch introduced MAP_FIXED_NOREPLACE which enforces the given
address but unlike MAP_FIXED it fails with EEXIST if the given range
conflicts with an existing one. The flag is introduced as a completely
new one rather than a MAP_FIXED extension because of the backward
compatibility. We really want a never-clobber semantic even on older
kernels which do not recognize the flag. Unfortunately mmap sucks
wrt flags evaluation because we do not EINVAL on unknown flags. On
those kernels we would simply use the traditional hint based semantic so
the caller can still get a different address (which sucks) but at least
not silently corrupt an existing mapping. I do not see a good way
around that. Except we won't export expose the new semantic to the
userspace at all.
It seems there are users who would like to have something like that.
Jemalloc has been mentioned by Michael Ellerman [7]
Florian Weimer has mentioned the following:
: glibc ld.so currently maps DSOs without hints. This means that the kernel
: will map right next to each other, and the offsets between them a completely
: predictable. We would like to change that and supply a random address in a
: window of the address space. If there is a conflict, we do not want the
: kernel to pick a non-random address. Instead, we would try again with a
: random address.
John Hubbard has mentioned CUDA example
: a) Searches /proc/<pid>/maps for a "suitable" region of available
: VA space. "Suitable" generally means it has to have a base address
: within a certain limited range (a particular device model might
: have odd limitations, for example), it has to be large enough, and
: alignment has to be large enough (again, various devices may have
: constraints that lead us to do this).
:
: This is of course subject to races with other threads in the process.
:
: Let's say it finds a region starting at va.
:
: b) Next it does:
: p = mmap(va, ...)
:
: *without* setting MAP_FIXED, of course (so va is just a hint), to
: attempt to safely reserve that region. If p != va, then in most cases,
: this is a failure (almost certainly due to another thread getting a
: mapping from that region before we did), and so this layer now has to
: call munmap(), before returning a "failure: retry" to upper layers.
:
: IMPROVEMENT: --> if instead, we could call this:
:
: p = mmap(va, ... MAP_FIXED_NOREPLACE ...)
:
: , then we could skip the munmap() call upon failure. This
: is a small thing, but it is useful here. (Thanks to Piotr
: Jaroszynski and Mark Hairgrove for helping me get that detail
: exactly right, btw.)
:
: c) After that, CUDA suballocates from p, via:
:
: q = mmap(sub_region_start, ... MAP_FIXED ...)
:
: Interestingly enough, "freeing" is also done via MAP_FIXED, and
: setting PROT_NONE to the subregion. Anyway, I just included (c) for
: general interest.
Atomic address range probing in the multithreaded programs in general
sounds like an interesting thing to me.
The second patch simply replaces MAP_FIXED use in elf loader by
MAP_FIXED_NOREPLACE. I believe other places which rely on MAP_FIXED
should follow. Actually real MAP_FIXED usages should be docummented
properly and they should be more of an exception.
[1] http://lkml.kernel.org/r/20171116101900.13621-1-mhocko@kernel.org
[2] http://lkml.kernel.org/r/20171129144219.22867-1-mhocko@kernel.org
[3] http://lkml.kernel.org/r/20171107162217.382cd754@canb.auug.org.au
[4] http://lkml.kernel.org/r/1510048229.12079.7.camel@abdul.in.ibm.com
[5] http://lkml.kernel.org/r/20171023082608.6167-1-mhocko@kernel.org
[6] http://lkml.kernel.org/r/20171113094203.aofz2e7kueitk55y@dhcp22.suse.cz
[7] http://lkml.kernel.org/r/87efp1w7vy.fsf@concordia.ellerman.id.au
This patch (of 2):
MAP_FIXED is used quite often to enforce mapping at the particular range.
The main problem of this flag is, however, that it is inherently dangerous
because it unmaps existing mappings covered by the requested range. This
can cause silent memory corruptions. Some of them even with serious
security implications. While the current semantic might be really
desiderable in many cases there are others which would want to enforce the
given range but rather see a failure than a silent memory corruption on a
clashing range. Please note that there is no guarantee that a given range
is obeyed by the mmap even when it is free - e.g. arch specific code is
allowed to apply an alignment.
Introduce a new MAP_FIXED_NOREPLACE flag for mmap to achieve this
behavior. It has the same semantic as MAP_FIXED wrt. the given address
request with a single exception that it fails with EEXIST if the requested
address is already covered by an existing mapping. We still do rely on
get_unmaped_area to handle all the arch specific MAP_FIXED treatment and
check for a conflicting vma after it returns.
The flag is introduced as a completely new one rather than a MAP_FIXED
extension because of the backward compatibility. We really want a
never-clobber semantic even on older kernels which do not recognize the
flag. Unfortunately mmap sucks wrt. flags evaluation because we do not
EINVAL on unknown flags. On those kernels we would simply use the
traditional hint based semantic so the caller can still get a different
address (which sucks) but at least not silently corrupt an existing
mapping. I do not see a good way around that.
[mpe@ellerman.id.au: fix whitespace]
[fail on clashing range with EEXIST as per Florian Weimer]
[set MAP_FIXED before round_hint_to_min as per Khalid Aziz]
Link: http://lkml.kernel.org/r/20171213092550.2774-2-mhocko@kernel.org
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Jason Evans <jasone@google.com>
Cc: David Goldblatt <davidtgoldblatt@gmail.com>
Cc: Edward Tomasz Napierała <trasz@FreeBSD.org>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "exec: Pin stack limit during exec".
Attempts to solve problems with the stack limit changing during exec
continue to be frustrated[1][2]. In addition to the specific issues
around the Stack Clash family of flaws, Andy Lutomirski pointed out[3]
other places during exec where the stack limit is used and is assumed to
be unchanging. Given the many places it gets used and the fact that it
can be manipulated/raced via setrlimit() and prlimit(), I think the only
way to handle this is to move away from the "current" view of the stack
limit and instead attach it to the bprm, and plumb this down into the
functions that need to know the stack limits. This series implements
the approach.
[1] 04e35f4495 ("exec: avoid RLIMIT_STACK races with prlimit()")
[2] 779f4e1c6c ("Revert "exec: avoid RLIMIT_STACK races with prlimit()"")
[3] to security@kernel.org, "Subject: existing rlimit races?"
This patch (of 3):
Since it is possible that the stack rlimit can change externally during
exec (either via another thread calling setrlimit() or another process
calling prlimit()), provide a way to pass the rlimit down into the
per-architecture mm layout functions so that the rlimit can stay in the
bprm structure instead of sitting in the signal structure until exec is
finalized.
Link: http://lkml.kernel.org/r/1518638796-20819-2-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hugh Dickins <hughd@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop our own compat binfmt implementation in
arch/parisc/kernel/binfmt_elf32.c in favour of the generic
implementation with CONFIG_COMPAT_BINFMT_ELF.
While cleaning up the dependencies, I noticed that ELF_PLATFORM was strangely
defined: On a 32-bit kernel, it was defined to "PARISC", while when running in
compat mode on a 64-bit kernel it was defined to "PARISC32". Since it doesn't
seem to be used in glibc yet, it's now defined in both cases to "PARISC". In
any case, it can be distinguished because it's either a 32-bit or a 64-bit ELF
file.
Signed-off-by: Helge Deller <deller@gmx.de>
Posix and common sense requires that SI_USER not be a signal specific
si_code. Thus add a new FPE_CONDTRAP si_code for conditional traps.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Subsystem:
- Add tracepoints
- Rework of the RTC/nvmem API to allow drivers to discard struct nvmem_config
after registration
- New range API, drivers can now expose the useful range of the RTC
- New offset API the core is now able to add an offset to the RTC time,
modifying the supported range.
- Multiple rtc_time64_to_tm fixes
- Handle time_t overflow on 32 bit platforms in the core instead of letting
drivers do crazy things.
- remove rtc_control API
New driver:
- Intersil ISL12026
Drivers:
- Drivers exposing the RTC non volatile memory have been converted to use nvmem
- Removed useless time and date validation
- Removed an indirection pattern that was a cargo cult from ancient drivers
- Removed VLA usage
- Fixed a possible race condition in probe functions
- AB8540 support is dropped from ab8500
- pcf85363 now has alarm support
-----BEGIN PGP SIGNATURE-----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=l9i8
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This contains a few series that have been in preparation for a while
and that will help systems with RTCs that will fail in 2038, 2069 or
2100.
Subsystem:
- Add tracepoints
- Rework of the RTC/nvmem API to allow drivers to discard struct
nvmem_config after registration
- New range API, drivers can now expose the useful range of the RTC
- New offset API the core is now able to add an offset to the RTC
time, modifying the supported range.
- Multiple rtc_time64_to_tm fixes
- Handle time_t overflow on 32 bit platforms in the core instead of
letting drivers do crazy things.
- remove rtc_control API
New driver:
- Intersil ISL12026
Drivers:
- Drivers exposing the RTC non volatile memory have been converted to
use nvmem
- Removed useless time and date validation
- Removed an indirection pattern that was a cargo cult from ancient
drivers
- Removed VLA usage
- Fixed a possible race condition in probe functions
- AB8540 support is dropped from ab8500
- pcf85363 now has alarm support"
* tag 'rtc-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (128 commits)
rtc: snvs: Fix usage of snvs_rtc_enable
rtc: mt7622: fix module autoloading for OF platform drivers
rtc: isl12022: use true and false for boolean values
rtc: ab8500: Drop AB8540 support
rtc: remove a warning during scripts/kernel-doc step
rtc: 88pm860x: remove artificial limitation
rtc: 88pm80x: remove artificial limitation
rtc: st-lpc: remove artificial limitation
rtc: mrst: remove artificial limitation
rtc: mv: remove artificial limitation
rtc: hctosys: Ensure system time doesn't overflow time_t
parisc: time: stop validating rtc_time in .read_time
rtc: pcf85063: fix clearing bits in pcf85063_start_clock
rtc: at91sam9: Set name of regmap_config
rtc: s5m: Remove VLA usage
rtc: s5m: Move enum from rtc.h to rtc-s5m.c
rtc: remove VLA usage
rtc: Add useful timestamp definitions
rtc: Add one offset seconds to expand RTC range
rtc: Factor out the RTC range validation into rtc_valid_range()
...
Thanks to commit 4b3ef9daa4 ("mm/swap: split swap cache into 64MB
trunks"), after swapoff the address_space associated with the swap
device will be freed. So page_mapping() users which may touch the
address_space need some kind of mechanism to prevent the address_space
from being freed during accessing.
The dcache flushing functions (flush_dcache_page(), etc) in architecture
specific code may access the address_space of swap device for anonymous
pages in swap cache via page_mapping() function. But in some cases
there are no mechanisms to prevent the swap device from being swapoff,
for example,
CPU1 CPU2
__get_user_pages() swapoff()
flush_dcache_page()
mapping = page_mapping()
... exit_swap_address_space()
... kvfree(spaces)
mapping_mapped(mapping)
The address space may be accessed after being freed.
But from cachetlb.txt and Russell King, flush_dcache_page() only care
about file cache pages, for anonymous pages, flush_anon_page() should be
used. The implementation of flush_dcache_page() in all architectures
follows this too. They will check whether page_mapping() is NULL and
whether mapping_mapped() is true to determine whether to flush the
dcache immediately. And they will use interval tree (mapping->i_mmap)
to find all user space mappings. While mapping_mapped() and
mapping->i_mmap isn't used by anonymous pages in swap cache at all.
So, to fix the race between swapoff and flush dcache, __page_mapping()
is add to return the address_space for file cache pages and NULL
otherwise. All page_mapping() invoking in flush dcache functions are
replaced with page_mapping_file().
[akpm@linux-foundation.org: simplify page_mapping_file(), per Mike]
Link: http://lkml.kernel.org/r/20180305083634.15174-1-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
"Lots of small enhancements and fixes in this patchset:
- improved the x86-64 compatibility for PCI cards by returning -1UL
for timed out MMIO transactions (instead of crashing)
- fixed HPMC handler for PAT machines: size needs to be multiple of 16
- prepare machine_power_off() to be able to turn rp3410 and c8000
machines off via IMPI
- added code to extract machine info for usage with qemu
- some init sections fixes
- lots of fixes for sparse-, ubsan- and uninitalized variables
warnings"
* 'parisc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix out of array access in match_pci_device()
parisc: Add code generator for Qemu/SeaBIOS machine info
parisc/pci: Switch LBA PCI bus from Hard Fail to Soft Fail mode
parisc: Fix HPMC handler by increasing size to multiple of 16 bytes
parisc: Directly call machine_power_off() in power button driver
parisc: machine_power_off() should call pm_power_off()
parisc/Kconfig: SMP kernels boot on all machines
parisc: Silence uninitialized variable warning in dbl_to_sgl_fcnvff()
parisc: Move various functions and strings to init section
parisc: Convert MAP_TYPE to cover 4 bits on parisc
parisc: Force to various endian types for sparse
parisc/gscps2: Fix sparse warnings
parisc/led: Fix sparse warnings
parisc/parport_gsc: Use NULL to avoid sparse warning
parisc/stifb: Use fb_memset() to avoid sparse warning
Pull removal of in-kernel calls to syscalls from Dominik Brodowski:
"System calls are interaction points between userspace and the kernel.
Therefore, system call functions such as sys_xyzzy() or
compat_sys_xyzzy() should only be called from userspace via the
syscall table, but not from elsewhere in the kernel.
At least on 64-bit x86, it will likely be a hard requirement from
v4.17 onwards to not call system call functions in the kernel: It is
better to use use a different calling convention for system calls
there, where struct pt_regs is decoded on-the-fly in a syscall wrapper
which then hands processing over to the actual syscall function. This
means that only those parameters which are actually needed for a
specific syscall are passed on during syscall entry, instead of
filling in six CPU registers with random user space content all the
time (which may cause serious trouble down the call chain). Those
x86-specific patches will be pushed through the x86 tree in the near
future.
Moreover, rules on how data may be accessed may differ between kernel
data and user data. This is another reason why calling sys_xyzzy() is
generally a bad idea, and -- at most -- acceptable in arch-specific
code.
This patchset removes all in-kernel calls to syscall functions in the
kernel with the exception of arch/. On top of this, it cleans up the
three places where many syscalls are referenced or prototyped, namely
kernel/sys_ni.c, include/linux/syscalls.h and include/linux/compat.h"
* 'syscalls-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux: (109 commits)
bpf: whitelist all syscalls for error injection
kernel/sys_ni: remove {sys_,sys_compat} from cond_syscall definitions
kernel/sys_ni: sort cond_syscall() entries
syscalls/x86: auto-create compat_sys_*() prototypes
syscalls: sort syscall prototypes in include/linux/compat.h
net: remove compat_sys_*() prototypes from net/compat.h
syscalls: sort syscall prototypes in include/linux/syscalls.h
kexec: move sys_kexec_load() prototype to syscalls.h
x86/sigreturn: use SYSCALL_DEFINE0
x86: fix sys_sigreturn() return type to be long, not unsigned long
x86/ioport: add ksys_ioperm() helper; remove in-kernel calls to sys_ioperm()
mm: add ksys_readahead() helper; remove in-kernel calls to sys_readahead()
mm: add ksys_mmap_pgoff() helper; remove in-kernel calls to sys_mmap_pgoff()
mm: add ksys_fadvise64_64() helper; remove in-kernel call to sys_fadvise64_64()
fs: add ksys_fallocate() wrapper; remove in-kernel calls to sys_fallocate()
fs: add ksys_p{read,write}64() helpers; remove in-kernel calls to syscalls
fs: add ksys_truncate() wrapper; remove in-kernel calls to sys_truncate()
fs: add ksys_sync_file_range helper(); remove in-kernel calls to syscall
kernel: add ksys_setsid() helper; remove in-kernel call to sys_setsid()
kernel: add ksys_unshare() helper; remove in-kernel calls to sys_unshare()
...
Using this helper allows us to avoid the in-kernel calls to the
sys_readahead() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_readahead().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the
sys_mmap_pgoff() syscall. The ksys_ prefix denotes that this function is
meant as a drop-in replacement for the syscall. In particular, it uses the
same calling convention as sys_mmap_pgoff().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_fadvise64_64() helper allows us to avoid the in-kernel
calls to the sys_fadvise64_64() syscall. The ksys_ prefix denotes that
this function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as ksys_fadvise64_64().
Some compat stubs called sys_fadvise64(), which then just passed through
the arguments to sys_fadvise64_64(). Get rid of this indirection, and call
ksys_fadvise64_64() directly.
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mm@kvack.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_fallocate() wrapper allows us to get rid of in-kernel
calls to the sys_fallocate() syscall. The ksys_ prefix denotes that this
function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as sys_fallocate().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_p{read,write}64() wrappers allows us to get rid of
in-kernel calls to the sys_pread64() and sys_pwrite64() syscalls.
The ksys_ prefix denotes that this function is meant as a drop-in
replacement for the syscall. In particular, it uses the same calling
convention as sys_p{read,write}64().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_truncate() wrapper allows us to get rid of in-kernel
calls to the sys_truncate() syscall. The ksys_ prefix denotes that this
function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as sys_truncate().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using this helper allows us to avoid the in-kernel calls to the
sys_sync_file_range() syscall. The ksys_ prefix denotes that this function
is meant as a drop-in replacement for the syscall. In particular, it uses
the same calling convention as sys_sync_file_range().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Using the ksys_ftruncate() wrapper allows us to get rid of in-kernel
calls to the sys_ftruncate() syscall. The ksys_ prefix denotes that this
function is meant as a drop-in replacement for the syscall. In
particular, it uses the same calling convention as sys_ftruncate().
This patch is part of a series which removes in-kernel calls to syscalls.
On this basis, the syscall entry path can be streamlined. For details, see
http://lkml.kernel.org/r/20180325162527.GA17492@light.dominikbrodowski.net
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As found by the ubsan checker, the value of the 'index' variable can be
out of range for the bc[] array:
UBSAN: Undefined behaviour in arch/parisc/kernel/drivers.c:655:21
index 6 is out of range for type 'char [6]'
Backtrace:
[<104fa850>] __ubsan_handle_out_of_bounds+0x68/0x80
[<1019d83c>] check_parent+0xc0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019d86c>] check_parent+0xf0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019d938>] descend_children+0x4c/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019cffc>] hwpath_to_device+0xa4/0xc4
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Qemu now supports emulating PA-RISC machines. For that a forked version
of SeaBIOS available at https://github.com/hdeller/seabios-hppa is used
which requires some information about the emulated machine.
This patch adds code to generate a header file with the necessary
information for SeaBIOS. The information is extracted from the firmware
the current kernel is running on.
Tested on a B160L workstation.
Signed-off-by: Helge Deller <deller@gmx.de>
Make sure that the HPMC (High Priority Machine Check) handler is 16-byte
aligned and that it's length in the IVT is a multiple of 16 bytes.
Otherwise PDC may decide not to call the HPMC crash handler.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Smatch warns that is_tiny can be used uninitialized:
arch/parisc/math-emu/fcnvff.c:297 dbl_to_sgl_fcnvff()
error: uninitialized symbol 'is_tiny'.
This code is very old so that suggests the bug doesn't have a huge
affect in real life. But I've read the code and it seems like a
reasonable warning. Either way it should be harmless to initialize it
to false and silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Helge Deller <deller@gmx.de>
On parisc we want to be as much as possible compatible to the major
architectures like x86. Those architectures have MAP_TYPE defined as 0x0f which
covers MAP_SHARED and MAP_PRIVATE and leaves two more bits unused.
In contrast, on parisc we have MAP_TYPE defined to 0x03 which covers MAP_SHARED
and MAP_PRIVATE only. But we don't have the 2 bits free as x86.
Usually that's not a problem, but during the discussions for pmem+dax support
the idea came up to use the two remaining bits of MAP_TYPE (on x86 and others)
for the new MAP_DIRECT and MAP_SYNC flags. One requirement is, that an old
kernel should correctly handle MAP_DIRECT and MAP_SYNC and fail on those if
set. This only works if MAP_TYPE has 4 bits.
Even though the pmem+dax people now choosed another solution via
MAP_SHARED_VALIDATE, let's still proceed to be more compatible to x86 by adding
two more bits for future usage.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
The RTC core is always calling rtc_valid_tm after the read_time callback.
It is not necessary to call it just before returning from the callback.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Just when I had decided that flush_cache_range() was always called with
a valid context, Helge reported two cases where the
"BUG_ON(!vma->vm_mm->context);" was hit on the phantom buildd:
kernel BUG at /mnt/sdb6/linux/linux-4.15.4/arch/parisc/kernel/cache.c:587!
CPU: 1 PID: 3254 Comm: kworker/1:2 Tainted: G D 4.15.0-1-parisc64-smp #1 Debian 4.15.4-1+b1
Workqueue: events free_ioctx
IAOQ[0]: flush_cache_range+0x164/0x168
IAOQ[1]: flush_cache_page+0x0/0x1c8
RP(r2): unmap_page_range+0xae8/0xb88
Backtrace:
[<00000000404a6980>] unmap_page_range+0xae8/0xb88
[<00000000404a6ae0>] unmap_single_vma+0xc0/0x188
[<00000000404a6cdc>] zap_page_range_single+0x134/0x1f8
[<00000000404a702c>] unmap_mapping_range+0x1cc/0x208
[<0000000040461518>] truncate_pagecache+0x98/0x108
[<0000000040461624>] truncate_setsize+0x9c/0xb8
[<00000000405d7f30>] put_aio_ring_file+0x80/0x100
[<00000000405d803c>] aio_free_ring+0x8c/0x290
[<00000000405d82c0>] free_ioctx+0x80/0x180
[<0000000040284e6c>] process_one_work+0x21c/0x668
[<00000000402854c4>] worker_thread+0x20c/0x778
[<0000000040291d44>] kthread+0x2d4/0x2e0
[<0000000040204020>] end_fault_vector+0x20/0xc0
This indicates that we need to handle the no context case in
flush_cache_range() as we do in flush_cache_mm().
In thinking about this, I realized that we don't need to flush the TLB
when there is no context. So, I added context checks to the large flush
cases in flush_cache_mm() and flush_cache_range(). The large flush case
occurs frequently in flush_cache_mm() and the change should improve fork
performance.
The v2 version of this change removes the BUG_ON from flush_cache_page()
by skipping the TLB flush when there is no context. I also added code
to flush the TLB in flush_cache_mm() and flush_cache_range() when we
have a context that's not current. Now all three routines handle TLB
flushes in a similar manner.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull parisc fixes from Helge Deller:
- a patch to change the ordering of cache and TLB flushes to hopefully
fix the random segfaults we very rarely face (by Dave Anglin).
- a patch to hide the virtual kernel memory layout due to security
reasons.
- two small patches to make the kernel run more smoothly under qemu.
* 'parisc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
When run under QEMU, calling mfctl(16) creates some overhead because the
qemu timer has to be scaled and moved into the register. This patch
reduces the number of calls to mfctl(16) by moving the calls out of the
loops.
Additionally, increase the minimal time interval to 8000 cycles instead
of 500 to compensate possible QEMU delays when delivering interrupts.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.14+
When running on qemu we know that the (emulated) cr16 cpu-internal
clocks are syncronized. So let's use them unconditionally on qemu.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.14+
The architecture specification says (for 64-bit systems): PDC is a per
processor resource, and operating system software must be prepared to
manage separate pointers to PDCE_PROC for each processor. The address
of PDCE_PROC for the monarch processor is stored in the Page Zero
location MEM_PDC. The address of PDCE_PROC for each non-monarch
processor is passed in gr26 when PDCE_RESET invokes OS_RENDEZ.
Currently we still use one PDC for all CPUs, but in case we face a
machine which is following the specification let's warn about it.
Signed-off-by: Helge Deller <deller@gmx.de>
The change to flush_kernel_vmap_range() wasn't sufficient to avoid the
SMP stalls. The problem is some drivers call these routines with
interrupts disabled. Interrupts need to be enabled for flush_tlb_all()
and flush_cache_all() to work. This version adds checks to ensure
interrupts are not disabled before calling routines that need IPI
interrupts. When interrupts are disabled, we now drop into slower code.
The attached change fixes the ordering of cache and TLB flushes in
several cases. When we flush the cache using the existing PTE/TLB
entries, we need to flush the TLB after doing the cache flush. We don't
need to do this when we flush the entire instruction and data caches as
these flushes don't use the existing TLB entries. The same is true for
tmpalias region flushes.
The flush_kernel_vmap_range() and invalidate_kernel_vmap_range()
routines have been updated.
Secondly, we added a new purge_kernel_dcache_range_asm() routine to
pacache.S and use it in invalidate_kernel_vmap_range(). Nominally,
purges are faster than flushes as the cache lines don't have to be
written back to memory.
Hopefully, this is sufficient to resolve the remaining problems due to
cache speculation. So far, testing indicates that this is the case. I
did work up a patch using tmpalias flushes, but there is a performance
hit because we need the physical address for each page, and we also need
to sequence access to the tmpalias flush code. This increases the
probability of stalls.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
to the clk rate protection support added by Jerome Brunet. This feature
will allow consumers to lock in a certain rate on the output of a clk so
that things like audio playback don't hear pops when the clk frequency
changes due to shared parent clks changing rates. Currently the clk
API doesn't guarantee the rate of a clk stays at the rate you request
after clk_set_rate() is called, so this new API will allow drivers
to express that requirement. Beyond this, the core got some debugfs
pretty printing patches and a couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h file
causes small one-liners in all the architecture Kbuild files. Overall, the
driver diff seems to be the normal stuff that comes all the time to
fix little problems here and there and to support new hardware.
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bGPp
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
Pull printk updates from Petr Mladek:
- Add a console_msg_format command line option:
The value "default" keeps the old "[time stamp] text\n" format. The
value "syslog" allows to see the syslog-like "<log
level>[timestamp] text" format.
This feature was requested by people doing regression tests, for
example, 0day robot. They want to have both filtered and full logs
at hands.
- Reduce the risk of softlockup:
Pass the console owner in a busy loop.
This is a new approach to the old problem. It was first proposed by
Steven Rostedt on Kernel Summit 2017. It marks a context in which
the console_lock owner calls console drivers and could not sleep.
On the other side, printk() callers could detect this state and use
a busy wait instead of a simple console_trylock(). Finally, the
console_lock owner checks if there is a busy waiter at the end of
the special context and eventually passes the console_lock to the
waiter.
The hand-off works surprisingly well and helps in many situations.
Well, there is still a possibility of the softlockup, for example,
when the flood of messages stops and the last owner still has too
much to flush.
There is increasing number of people having problems with
printk-related softlockups. We might eventually need to get better
solution. Anyway, this looks like a good start and promising
direction.
- Do not allow to schedule in console_unlock() called from printk():
This reverts an older controversial commit. The reschedule helped
to avoid softlockups. But it also slowed down the console output.
This patch is obsoleted by the new console waiter logic described
above. In fact, the reschedule made the hand-off less effective.
- Deprecate "%pf" and "%pF" format specifier:
It was needed on ia64, ppc64 and parisc64 to dereference function
descriptors and show the real function address. It is done
transparently by "%ps" and "pS" format specifier now.
Sergey Senozhatsky found that all the function descriptors were in
a special elf section and could be easily detected.
- Remove printk_symbol() API:
It has been obsoleted by "%pS" format specifier, and this change
helped to remove few continuous lines and a less intuitive old API.
- Remove redundant memsets:
Sergey removed unnecessary memset when processing printk.devkmsg
command line option.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (27 commits)
printk: drop redundant devkmsg_log_str memsets
printk: Never set console_may_schedule in console_trylock()
printk: Hide console waiter logic into helpers
printk: Add console owner and waiter logic to load balance console writes
kallsyms: remove print_symbol() function
checkpatch: add pF/pf deprecation warning
symbol lookup: introduce dereference_symbol_descriptor()
parisc64: Add .opd based function descriptor dereference
powerpc64: Add .opd based function descriptor dereference
ia64: Add .opd based function descriptor dereference
sections: split dereference_function_descriptor()
openrisc: Fix conflicting types for _exext and _stext
lib: do not use print_symbol()
irq debug: do not use print_symbol()
sysfs: do not use print_symbol()
drivers: do not use print_symbol()
x86: do not use print_symbol()
unicore32: do not use print_symbol()
sh: do not use print_symbol()
mn10300: do not use print_symbol()
...
This pull requests contains a consolidation of the generic no-IOMMU code,
a well as the glue code for swiotlb. All the code is based on the x86
implementation with hooks to allow all architectures that aren't cache
coherent to use it. The x86 conversion itself has been deferred because
the x86 maintainers were a little busy in the last months.
-----BEGIN PGP SIGNATURE-----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=Nrl9
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"Except for a runtime warning fix from Christian this is all about
consolidation of the generic no-IOMMU code, a well as the glue code
for swiotlb.
All the code is based on the x86 implementation with hooks to allow
all architectures that aren't cache coherent to use it.
The x86 conversion itself has been deferred because the x86
maintainers were a little busy in the last months"
* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
arm64: use swiotlb_alloc and swiotlb_free
arm64: replace ZONE_DMA with ZONE_DMA32
mips: use swiotlb_{alloc,free}
mips/netlogic: remove swiotlb support
tile: use generic swiotlb_ops
tile: replace ZONE_DMA with ZONE_DMA32
unicore32: use generic swiotlb_ops
ia64: remove an ifdef around the content of pci-dma.c
ia64: clean up swiotlb support
ia64: use generic swiotlb_ops
ia64: replace ZONE_DMA with ZONE_DMA32
swiotlb: remove various exports
swiotlb: refactor coherent buffer allocation
swiotlb: refactor coherent buffer freeing
swiotlb: wire up ->dma_supported in swiotlb_dma_ops
swiotlb: add common swiotlb_map_ops
swiotlb: rename swiotlb_free to swiotlb_exit
x86: rename swiotlb_dma_ops
powerpc: rename swiotlb_dma_ops
...
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
-----BEGIN PGP SIGNATURE-----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=jhWg
-----END PGP SIGNATURE-----
Merge tag 'init_task-20180117' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull init_task initializer cleanups from David Howells:
"It doesn't seem useful to have the init_task in a header file rather
than in a normal source file. We could consolidate init_task handling
instead and expand out various macros.
Here's a series of patches that consolidate init_task handling:
(1) Make THREAD_SIZE available to vmlinux.lds for cris, hexagon and
openrisc.
(2) Alter the INIT_TASK_DATA linker script macro to set
init_thread_union and init_stack rather than defining these in C.
Insert init_task and init_thread_into into the init_stack area in
the linker script as appropriate to the configuration, with
different section markers so that they end up correctly ordered.
We can then get merge ia64's init_task.c into the main one.
We then have a bunch of single-use INIT_*() macros that seem only
to be macros because they used to be used per-arch. We can then
expand these in place of the user and get rid of a few lines and
a lot of backslashes.
(3) Expand INIT_TASK() in place.
(4) Expand in place various small INIT_*() macros that are defined
conditionally. Expand them and surround them by #if[n]def/#endif
in the .c file as it takes fewer lines.
(5) Expand INIT_SIGNALS() and INIT_SIGHAND() in place.
(6) Expand INIT_STRUCT_PID in place.
These macros can then be discarded"
* tag 'init_task-20180117' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
Expand INIT_STRUCT_PID and remove
Expand the INIT_SIGNALS and INIT_SIGHAND macros and remove
Expand various INIT_* macros and remove
Expand INIT_TASK() in init/init_task.c and remove
Construct init thread stack in the linker script rather than by union
openrisc: Make THREAD_SIZE available to vmlinux.lds
hexagon: Make THREAD_SIZE available to vmlinux.lds
cris: Make THREAD_SIZE available to vmlinux.lds
Today 4 architectures set ARCH_SUPPORTS_MEMORY_FAILURE (arm64, parisc,
powerpc, and x86), while 4 other architectures set __ARCH_SI_TRAPNO
(alpha, metag, sparc, and tile). These two sets of architectures do
not interesect so remove the trapno paramater to remove confusion.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Among the existing architecture specific versions of
copy_siginfo_to_user32 there are several different implementation
problems. Some architectures fail to handle all of the cases in in
the siginfo union. Some architectures perform a blind copy of the
siginfo union when the si_code is negative. A blind copy suggests the
data is expected to be in 32bit siginfo format, which means that
receiving such a signal via signalfd won't work, or that the data is
in 64bit siginfo and the code is copying nonsense to userspace.
Create a single instance of copy_siginfo_to_user32 that all of the
architectures can share, and teach it to handle all of the cases in
the siginfo union correctly, with the assumption that siginfo is
stored internally to the kernel is 64bit siginfo format.
A special case is made for x86 x32 format. This is needed as presence
of both x32 and ia32 on x86_64 results in two different 32bit signal
formats. By allowing this small special case there winds up being
exactly one code base that needs to be maintained between all of the
architectures. Vastly increasing the testing base and the chances of
finding bugs.
As the x86 copy of copy_siginfo_to_user32 the call of the x86
signal_compat_build_tests were moved into sigaction_compat_abi, so
that they will keep running.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The function copy_siginfo_from_user32 is used for two things, in ptrace
since the dawn of siginfo for arbirarily modifying a signal that
user space sees, and in sigqueueinfo to send a signal with arbirary
siginfo data.
Create a single copy of copy_siginfo_from_user32 that all architectures
share, and teach it to handle all of the cases in the siginfo union.
In the generic version of copy_siginfo_from_user32 ensure that all
of the fields in siginfo are initialized so that the siginfo structure
can be safely copied to userspace if necessary.
When copying the embedded sigval union copy the si_int member. That
ensures the 32bit values passes through the kernel unchanged.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
--EWB Added #ifdef CONFIG_X86_X32_ABI to arch/x86/kernel/signal_compat.c
Changed #ifdef CONFIG_X86_X32 to #ifdef CONFIG_X86_X32_ABI in
linux/compat.h
CONFIG_X86_X32 is set when the user requests X32 support.
CONFIG_X86_X32_ABI is set when the user requests X32 support
and the tool-chain has X32 allowing X32 support to be built.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Setting si_code to 0 results in a userspace seeing an si_code of 0.
This is the same si_code as SI_USER. Posix and common sense requires
that SI_USER not be a signal specific si_code. As such this use of 0
for the si_code is a pretty horribly broken ABI.
Further use of si_code == 0 guaranteed that copy_siginfo_to_user saw a
value of __SI_KILL and now sees a value of SIL_KILL with the result
that uid and pid fields are copied and which might copying the si_addr
field by accident but certainly not by design. Making this a very
flakey implementation.
Utilizing FPE_FIXME siginfo_layout will now return SIL_FAULT and the
appropriate fields will reliably be copied.
This bug is 13 years old and parsic machines are no longer being built
so I don't know if it possible or worth fixing it. But it is at least
worth documenting this so other architectures don't make the same
mistake.
Possible ABI fixes includee:
- Send the signal without siginfo
- Don't generate a signal
- Possibly assign and use an appropriate si_code
- Don't handle cases which can't happen
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Ref: 313c01d3e3fd ("[PATCH] PA-RISC update for 2.6.0")
Histroy Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Construct the init thread stack in the linker script rather than doing it
by means of a union so that ia64's init_task.c can be got rid of.
The following symbols are then made available from INIT_TASK_DATA() linker
script macro:
init_thread_union
init_stack
INIT_TASK_DATA() also expands the region to THREAD_SIZE to accommodate the
size of the init stack. init_thread_union is given its own section so that
it can be placed into the stack space in the right order. I'm assuming
that the ia64 ordering is correct and that the task_struct is first and the
thread_info second.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Will Deacon <will.deacon@arm.com> (arm64)
Tested-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
We are moving towards separate kernel and module function descriptor
dereference callbacks. This patch enables it for parisc64.
For pointers that belong to the kernel
- Added __start_opd and __end_opd pointers, to track the kernel
.opd section address range;
- Added dereference_kernel_function_descriptor(). Now we
will dereference only function pointers that are within
[__start_opd, __end_opd);
For pointers that belong to a module
- Added dereference_module_function_descriptor() to handle module
function descriptor dereference. Now we will dereference only
pointers that are within [module->opd.start, module->opd.end).
Link: http://lkml.kernel.org/r/20171109234830.5067-5-sergey.senozhatsky@gmail.com
To: Tony Luck <tony.luck@intel.com>
To: Fenghua Yu <fenghua.yu@intel.com>
To: Helge Deller <deller@gmx.de>
To: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To: Paul Mackerras <paulus@samba.org>
To: Michael Ellerman <mpe@ellerman.id.au>
To: James Bottomley <jejb@parisc-linux.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-ia64@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Helge Deller <deller@gmx.de> #parisc64
Signed-off-by: Petr Mladek <pmladek@suse.com>
Add qemu idle sleep support when running under qemu with SeaBIOS PDC
firmware.
Like the power architecture we use the "or" assembler instructions,
which translate to nops on real hardware, to indicate that qemu shall
idle sleep.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Richard Henderson <rth@twiddle.net>
CC: stable@vger.kernel.org # v4.9+
Now that every architecture is using the generic clkdev.h file
and we no longer include asm/clkdev.h anywhere in the tree, we
can remove it.
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Qemu for PARISC reported on a 32bit SMP parisc kernel strange failures
about "Not-handled unaligned insn 0x0e8011d6 and 0x0c2011c9."
Those opcodes evaluate to the ldcw() assembly instruction which requires
(on 32bit) an alignment of 16 bytes to ensure atomicity.
As it turns out, qemu is correct and in our assembly code in entry.S and
pacache.S we don't pay attention to the required alignment.
This patch fixes the problem by aligning the lock offset in assembly
code in the same manner as we do in our C-code.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.0+
In testing, I found that the thread stack can be 16 kB when using an irq
stack. Without it, the thread stack needs to be 32 kB. Currently, the irq
stack is 32 kB. While it probably could be 16 kB, I would prefer to leave it
as is for safety.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
This reverts commit 5c38602d83.
Interrupts can't be enabled early because the register saves are done on
the thread stack prior to switching to the IRQ stack. This caused stack
overflows and the thread stack needed increasing to 32k. Even then,
stack overflows still occasionally occurred.
Background:
Even with a 32 kB thread stack, I have seen instances where the thread
stack overflowed on the mx3210 buildd. Detection of stack overflow only
occurs when we have an external interrupt. When an external interrupt
occurs, we switch to the thread stack if we are not already on a kernel
stack. Then, registers and specials are saved to the kernel stack.
The bug occurs in intr_return where interrupts are reenabled prior to
returning from the interrupt. This was done incase we need to schedule
or deliver signals. However, it introduces the possibility that
multiple external interrupts may occur on the thread stack and cause a
stack overflow. These might not be detected and cause the kernel to
misbehave in random ways.
This patch changes the code back to only reenable interrupts when we are
going to schedule or deliver signals. As a result, we generally return
from an interrupt before reenabling interrupts. This minimizes the
growth of the thread stack.
Fixes: 5c38602d83 ("parisc: Re-enable interrupts early")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Helge Deller <deller@gmx.de>
These duplicate includes have been found with scripts/checkincludes.pl
but they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The os_hpmc_size variable sometimes wasn't aligned at word boundary and thus
triggered the unaligned fault handler at startup.
Fix it by aligning it properly.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Static analysis tools complain that we intended to have curly braces
around this indent block. In this case this assumption is wrong, so fix
the indenting.
Fixes: 2f3c7b8137 ("parisc: Add core code for self-extracting kernel")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Commit 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT
program type") introduced the bpf_perf_event_data structure which
exports the pt_regs structure. This is OK for multiple architectures
but fail for s390 and arm64 which do not export pt_regs. Programs
using them, for example, the bpf selftest fail to compile on these
architectures.
For s390, exporting the pt_regs is not an option because s390 wants
to allow changes to it. For arm64, there is a user_pt_regs structure
that covers parts of the pt_regs structure for use by user space.
To solve the broken uapi for s390 and arm64, introduce an abstract
type for pt_regs and add an asm/bpf_perf_event.h file that concretes
the type. An asm-generic header file covers the architectures that
export pt_regs today.
The arch-specific enablement for s390 and arm64 follows in separate
commits.
Reported-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Fixes: 0515e5999a ("bpf: introduce BPF_PROG_TYPE_PERF_EVENT program type")
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-and-tested-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull parisc updates from Helge Deller:
"Highlights:
- one important fix from Dave to prevent kernel crash when userspace
hands over invalid values to our in-kernel CAS implementation.
- added CPU topology support, including multi-core scheduler support
on PA8900 CPUs
Minor changes:
- minor fixes for sparse (from Luc)
- drop duplicates for CPU_BIG_ENDIAN from parisc and sparc top
Kconfig files (from Babu)
- reorganized parisc PDC (firmware-access) header files for usage
from userspace. Required for upcoming qemu parisc emulator and
SeaBIOS fork to support parisc"
* 'parisc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
arch: Fix duplicates in Kconfig for parisc and sparc
parisc: Make some PDC structures accessible in uapi headers
parisc: Pass endianness info to sparse
parisc: Add CPU topology support
parisc: Fix validity check of pointer size argument in new CAS implementation
-----BEGIN PGP SIGNATURE-----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=fCeF
-----END PGP SIGNATURE-----
Merge tag 'locks-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull file locking update from Jeff Layton:
"A couple of fixes for a patch that went into v4.14, and the bug report
just came in a few days ago.. It passes my (minimal) testing, and has
been in linux-next for a few days now.
I also would like to get my address changed in MAINTAINERS to clear
that hurdle"
* tag 'locks-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
fcntl: don't cap l_start and l_end values for F_GETLK64 in compat syscall
fcntl: don't leak fd reference when fixup_compat_flock fails
MAINTAINERS: s/jlayton@poochiereds.net/jlayton@kernel.org/
Pull compat and uaccess updates from Al Viro:
- {get,put}_compat_sigset() series
- assorted compat ioctl stuff
- more set_fs() elimination
- a few more timespec64 conversions
- several removals of pointless access_ok() in places where it was
followed only by non-__ variants of primitives
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
coredump: call do_unlinkat directly instead of sys_unlink
fs: expose do_unlinkat for built-in callers
ext4: take handling of EXT4_IOC_GROUP_ADD into a helper, get rid of set_fs()
ipmi: get rid of pointless access_ok()
pi433: sanitize ioctl
cxlflash: get rid of pointless access_ok()
mtdchar: get rid of pointless access_ok()
r128: switch compat ioctls to drm_ioctl_kernel()
selection: get rid of field-by-field copyin
VT_RESIZEX: get rid of field-by-field copyin
i2c compat ioctls: move to ->compat_ioctl()
sched_rr_get_interval(): move compat to native, get rid of set_fs()
mips: switch to {get,put}_compat_sigset()
sparc: switch to {get,put}_compat_sigset()
s390: switch to {get,put}_compat_sigset()
ppc: switch to {get,put}_compat_sigset()
parisc: switch to {get,put}_compat_sigset()
get_compat_sigset()
get rid of {get,put}_compat_itimerspec()
io_getevents: Use timespec64 to represent timeouts
...
* Introduce MAP_SYNC and MAP_SHARED_VALIDATE, a mechanism to enable
'userspace flush' of persistent memory updates via filesystem-dax
mappings. It arranges for any filesystem metadata updates that may be
required to satisfy a write fault to also be flushed ("on disk") before
the kernel returns to userspace from the fault handler. Effectively
every write-fault that dirties metadata completes an fsync() before
returning from the fault handler. The new MAP_SHARED_VALIDATE mapping
type guarantees that the MAP_SYNC flag is validated as supported by the
filesystem's ->mmap() file operation.
* Add support for the standard ACPI 6.2 label access methods that
replace the NVDIMM_FAMILY_INTEL (vendor specific) label methods. This
enables interoperability with environments that only implement the
standardized methods.
* Add support for the ACPI 6.2 NVDIMM media error injection methods.
* Add support for the NVDIMM_FAMILY_INTEL v1.6 DIMM commands for latch
last shutdown status, firmware update, SMART error injection, and
SMART alarm threshold control.
* Cleanup physical address information disclosures to be root-only.
* Fix revalidation of the DIMM "locked label area" status to support
dynamic unlock of the label area.
* Expand unit test infrastructure to mock the ACPI 6.2 Translate SPA
(system-physical-address) command and error injection commands.
Acknowledgements that came after the commits were pushed to -next:
957ac8c421 dax: fix PMD faults on zero-length files
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
a39e596baa xfs: support for synchronous DAX faults
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
7b565c9f96 xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
-----BEGIN PGP SIGNATURE-----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=h2vZ
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm and dax updates from Dan Williams:
"Save for a few late fixes, all of these commits have shipped in -next
releases since before the merge window opened, and 0day has given a
build success notification.
The ext4 touches came from Jan, and the xfs touches have Darrick's
reviewed-by. An xfstest for the MAP_SYNC feature has been through
a few round of reviews and is on track to be merged.
- Introduce MAP_SYNC and MAP_SHARED_VALIDATE, a mechanism to enable
'userspace flush' of persistent memory updates via filesystem-dax
mappings. It arranges for any filesystem metadata updates that may
be required to satisfy a write fault to also be flushed ("on disk")
before the kernel returns to userspace from the fault handler.
Effectively every write-fault that dirties metadata completes an
fsync() before returning from the fault handler. The new
MAP_SHARED_VALIDATE mapping type guarantees that the MAP_SYNC flag
is validated as supported by the filesystem's ->mmap() file
operation.
- Add support for the standard ACPI 6.2 label access methods that
replace the NVDIMM_FAMILY_INTEL (vendor specific) label methods.
This enables interoperability with environments that only implement
the standardized methods.
- Add support for the ACPI 6.2 NVDIMM media error injection methods.
- Add support for the NVDIMM_FAMILY_INTEL v1.6 DIMM commands for
latch last shutdown status, firmware update, SMART error injection,
and SMART alarm threshold control.
- Cleanup physical address information disclosures to be root-only.
- Fix revalidation of the DIMM "locked label area" status to support
dynamic unlock of the label area.
- Expand unit test infrastructure to mock the ACPI 6.2 Translate SPA
(system-physical-address) command and error injection commands.
Acknowledgements that came after the commits were pushed to -next:
- 957ac8c421 ("dax: fix PMD faults on zero-length files"):
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
- a39e596baa ("xfs: support for synchronous DAX faults") and
7b565c9f96 ("xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()")
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>"
* tag 'libnvdimm-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (49 commits)
acpi, nfit: add 'Enable Latch System Shutdown Status' command support
dax: fix general protection fault in dax_alloc_inode
dax: fix PMD faults on zero-length files
dax: stop requiring a live device for dax_flush()
brd: remove dax support
dax: quiet bdev_dax_supported()
fs, dax: unify IOMAP_F_DIRTY read vs write handling policy in the dax core
tools/testing/nvdimm: unit test clear-error commands
acpi, nfit: validate commands against the device type
tools/testing/nvdimm: stricter bounds checking for error injection commands
xfs: support for synchronous DAX faults
xfs: Implement xfs_filemap_pfn_mkwrite() using __xfs_filemap_fault()
ext4: Support for synchronous DAX faults
ext4: Simplify error handling in ext4_dax_huge_fault()
dax: Implement dax_finish_sync_fault()
dax, iomap: Add support for synchronous faults
mm: Define MAP_SYNC and VM_SYNC flags
dax: Allow tuning whether dax_insert_mapping_entry() dirties entry
dax: Allow dax_iomap_fault() to return pfn
dax: Fix comment describing dax_iomap_fault()
...
Fix duplicates for sparc and parisc. This was due these following commits.
1. commit 4c97a0c8fe ("arch: define CPU_BIG_ENDIAN for all fixed big
endian archs")
2. commit 97d9f96916 ("arch/sparc: Define config parameter
CPU_BIG_ENDIAN")
3. commit 74ad3d28af ("parisc: Define CONFIG_CPU_BIG_ENDIAN")
Remove duplicates.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Helge Deller <deller@gmx.de>
While working on a qemu and SeaBIOS-port to parisc, those PDC structures are
useful to have accessible from userspace.
Signed-off-by: Helge Deller <deller@gmx.de>
parisc is big-endian only but sparse assumes the same endianness as the
building machine.
This is problematic for code which expect __BYTE_ORDER__ being correctly
predefined by the compiler which sparse can then pre-process differently
from what gcc would.
Fix this by letting sparse know about the architecture endianness.
To: James Bottomley <jejb@parisc-linux.org>
To: Helge Deller <deller@gmx.de>
CC: linux-parisc@vger.kernel.org
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Add topology support, including multi-core scheduler support on
PA8800/PA8900 CPUs and enhanced output in /proc/cpuinfo, e.g.
lscpu now reports on a single-socket, dual-core machine:
Architecture: parisc64
CPU(s): 2
On-line CPU(s) list: 0,1
Thread(s) per core: 1
Core(s) per socket: 2
Socket(s): 1
CPU family: PA-RISC 2.0
Model name: PA8800 (Mako)
Signed-off-by: Helge Deller <deller@gmx.de>
As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS
implementation causes a kernel crash. The attached patch corrects the
off by one error in the argument validity check.
In reviewing the code, I noticed that we only perform word operations
with the pointer size argument. The subi instruction intentionally uses
a word condition on 64-bit kernels. Nullification was used instead of a
cmpib instruction as the branch should never be taken. The shlw
pseudo-operation generates a depw,z instruction and it clears the target
before doing a shift left word deposit. Thus, we don't need to clip the
upper 32 bits of this argument on 64-bit kernels.
Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic
code in libgcc is the only direct user of the new CAS implementation
that I am aware of.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
Currently, we're capping the values too low in the F_GETLK64 case. The
fields in that structure are 64-bit values, so we shouldn't need to do
any sort of fixup there.
Make sure we check that assumption at build time in the future however
by ensuring that the sizes we're copying will fit.
With this, we no longer need COMPAT_LOFF_T_MAX either, so remove it.
Fixes: 94073ad77f (fs/locks: don't mess with the address limit in compat_fcntl64)
Reported-by: Vitaly Lipatov <lav@etersoft.ru>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: David Howells <dhowells@redhat.com>
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture
doesn't support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=ALJf
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
<linux/pci.h> defines struct pci_bus and struct pci_dev and includes the
struct resource definition before including <asm/pci.h>. Nobody includes
<asm/pci.h> directly, so they don't need their own declarations.
Remove the redundant struct pci_dev, pci_bus, resource declarations.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> # CRIS
Acked-by: Ralf Baechle <ralf@linux-mips.org> # MIPS
All users of pcibios_set_master() include <linux/pci.h>, which already has
a declaration. Remove the unnecessary declarations from the <asm/pci.h>
files.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> # CRIS
Acked-by: Ralf Baechle <ralf@linux-mips.org> # MIPS
The mmap(2) syscall suffers from the ABI anti-pattern of not validating
unknown flags. However, proposals like MAP_SYNC need a mechanism to
define new behavior that is known to fail on older kernels without the
support. Define a new MAP_SHARED_VALIDATE flag pattern that is
guaranteed to fail on all legacy mmap implementations.
It is worth noting that the original proposal was for a standalone
MAP_VALIDATE flag. However, when that could not be supported by all
archs Linus observed:
I see why you *think* you want a bitmap. You think you want
a bitmap because you want to make MAP_VALIDATE be part of MAP_SYNC
etc, so that people can do
ret = mmap(NULL, size, PROT_READ | PROT_WRITE, MAP_SHARED
| MAP_SYNC, fd, 0);
and "know" that MAP_SYNC actually takes.
And I'm saying that whole wish is bogus. You're fundamentally
depending on special semantics, just make it explicit. It's already
not portable, so don't try to make it so.
Rename that MAP_VALIDATE as MAP_SHARED_VALIDATE, make it have a value
of 0x3, and make people do
ret = mmap(NULL, size, PROT_READ | PROT_WRITE, MAP_SHARED_VALIDATE
| MAP_SYNC, fd, 0);
and then the kernel side is easier too (none of that random garbage
playing games with looking at the "MAP_VALIDATE bit", but just another
case statement in that map type thing.
Boom. Done.
Similar to ->fallocate() we also want the ability to validate the
support for new flags on a per ->mmap() 'struct file_operations'
instance basis. Towards that end arrange for flags to be generically
validated against a mmap_supported_flags exported by 'struct
file_operations'. By default all existing flags are implicitly
supported, but new flags require MAP_SHARED_VALIDATE and
per-instance-opt-in.
Cc: Jan Kara <jack@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Suggested-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be. This makes it hard for
compliance tools to determine the correct license.
Update these files with an SPDX license identifier. The identifier was
chosen based on the license information in the file.
GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.
Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier. The format
is:
((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)
SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text. The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After we removed all the dead wood it turns out only two architectures
actually implement dma_cache_sync as a real op: mips and parisc. Add
a cache_sync method to struct dma_map_ops and implement it for the
mips defualt DMA ops, and the parisc pa11 ops.
Note that arm, arc and openrisc support DMA_ATTR_NON_CONSISTENT, but
never provided a functional dma_cache_sync implementations, which
seems somewhat odd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
For CPUs which have an unknown or invalid CPU location (physical location)
assume that their cycle counters aren't syncronized across CPUs.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: c8c3735997 ("parisc: Enhance detection of synchronous cr16 clocksources")
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Helge Deller <deller@gmx.de>
__cmpxchg_u64 is built and used outside CONFIG_64BIT and thus needs to
be exported. This fixes the following build error seen when building
parisc:allmodconfig.
ERROR: "__cmpxchg_u64" [drivers/net/ethernet/intel/i40e/i40e.ko] undefined!
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Helge Deller <deller@gmx.de>
As discussed on the debian-hppa list, double-wordcompare and exchange
operations fail on 32-bit kernels. Looking at the code, I realized that
the ",ma" completer does the wrong thing in the "ldw,ma 4(%r26), %r29"
instruction. This increments %r26 and causes the following store to
write to the wrong location.
Note by Helge Deller:
The patch applies cleanly to stable kernel series if this upstream
commit is merged in advance:
f4125cfdb3 ("parisc: Avoid trashing sr2 and sr3 in LWS code").
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Christoph Biedl <debian.axhn@manchmal.in-ulm.de>
Fixes: 8920649120 ("parisc: Implement new LWS CAS supporting 64 bit operations.")
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>
The arch_{read,spin,write}_lock_flags() macros are simply mapped to the
non-flags versions by the majority of architectures, so do this in core
code and remove the dummy implementations. Also remove the implementation
in spinlock_up.h, since all callers of do_raw_spin_lock_flags() call
local_irq_save(flags) anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: paulmck@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1507055129-12300-4-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Outside of the locking code itself, {read,spin,write}_can_lock() have no
users in tree. Apparmor (the last remaining user of write_can_lock()) got
moved over to lockdep by the previous patch.
This patch removes the use of {read,spin,write}_can_lock() from the
BUILD_LOCK_OPS macro, deferring to the trylock operation for testing the
lock status, and subsequently removes the unused macros altogether. They
aren't guaranteed to work in a concurrent environment and can give
incorrect results in the case of qrwlock.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: paulmck@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1507055129-12300-2-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
gcc-7 optimizes the byte-wise accesses of get_unaligned_le32() into
word-wise accesses if the 32-bit integer output_len is declared as
external. This panics then the bootloader since we don't have the
unaligned access fault trap handler installed during boot time.
Avoid this optimization by declaring output_len as byte-aligned and thus
unbreak the bootloader code.
Additionally, compile the boot code optimized for size.
Signed-off-by: Helge Deller <deller@gmx.de>
By adding the feature to build the kernel as self-extracting
executeable, the possibility to simply compress the kernel with gzip was
lost.
This patch now reintroduces this possibilty again and leaves it up to
the user to decide how the kernel should be built.
The palo bootloader is able to natively load both formats.
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 24587380f6 ("parisc: Add MADV_HWPOISON and MADV_SOFT_OFFLINE") added
the necessary constants to handle hardware-poisoning. Those were needed to
support the page deallocation feature from firmware.
But I completely missed to add the relevant fault handler code. This now
showed up when I ran the madvise07 testcase from the Linux Test Project,
which failed with a kernel BUG at arch/parisc/mm/fault.c:320.
With this patch the parisc kernel now behaves like other platforms and
gives the same kernel syslog warnings when poisoning pages.
Signed-off-by: Helge Deller <deller@gmx.de>
While scanning the PDT for reported broken memory modules, warn if the
initrd was coincidentally loaded into bad memory.
Signed-off-by: Helge Deller <deller@gmx.de>
According to the programming note at page 1-31 of the PA 1.1 Firmware
Architecture document, one should use the PDC_INSTR firmware function to
get the instruction that invokes a PDCE_CHECK in the HPMC handler. This
patch follows this note and sets the instruction which has been a nop up
until now.
Testing on a C3000 and C8000 showed that this firmware call isn't
implemented on those machines, so maybe it's only needed on older ones.
Signed-off-by: Helge Deller <deller@gmx.de>
Check stack pointer if we are reaching the stack end and stop unwinding
if we do. This fixes early backtraces and avoids showing unrealistic
call stacks.
Signed-off-by: Helge Deller <deller@gmx.de>
The broken lockup_detector_suspend/resume() interface is going away. Use
the new lockup_detector_soft_poweroff() interface to stop the watchdog from
the busy looping power off routine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: linux-parisc@vger.kernel.org
Link: http://lkml.kernel.org/r/20170912194146.407385557@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull namespace updates from Eric Biederman:
"Life has been busy and I have not gotten half as much done this round
as I would have liked. I delayed it so that a minor conflict
resolution with the mips tree could spend a little time in linux-next
before I sent this pull request.
This includes two long delayed user namespace changes from Kirill
Tkhai. It also includes a very useful change from Serge Hallyn that
allows the security capability attribute to be used inside of user
namespaces. The practical effect of this is people can now untar
tarballs and install rpms in user namespaces. It had been suggested to
generalize this and encode some of the namespace information
information in the xattr name. Upon close inspection that makes the
things that should be hard easy and the things that should be easy
more expensive.
Then there is my bugfix/cleanup for signal injection that removes the
magic encoding of the siginfo union member from the kernel internal
si_code. The mips folks reported the case where I had used FPE_FIXME
me is impossible so I have remove FPE_FIXME from mips, while at the
same time including a return statement in that case to keep gcc from
complaining about unitialized variables.
I almost finished the work to get make copy_siginfo_to_user a trivial
copy to user. The code is available at:
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace.git neuter-copy_siginfo_to_user-v3
But I did not have time/energy to get the code posted and reviewed
before the merge window opened.
I was able to see that the security excuse for just copying fields
that we know are initialized doesn't work in practice there are buggy
initializations that don't initialize the proper fields in siginfo. So
we still sometimes copy unitialized data to userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
Introduce v3 namespaced file capabilities
mips/signal: In force_fcr31_sig return in the impossible case
signal: Remove kernel interal si_code magic
fcntl: Don't use ambiguous SIG_POLL si_codes
prctl: Allow local CAP_SYS_ADMIN changing exe_file
security: Use user_namespace::level to avoid redundant iterations in cap_capable()
userns,pidns: Verify the userns for new pid namespaces
signal/testing: Don't look for __SI_FAULT in userspace
signal/mips: Document a conflict with SI_USER with SIGFPE
signal/sparc: Document a conflict with SI_USER with SIGFPE
signal/ia64: Document a conflict with SI_USER with SIGFPE
signal/alpha: Document a conflict with SI_USER for SIGTRAP
Patch series "Define CPU_BIG_ENDIAN or warn for inconsistencies", v3.
While working on enabling queued rwlock on SPARC, found this following
code in include/asm-generic/qrwlock.h which uses CONFIG_CPU_BIG_ENDIAN to
clear a byte.
static inline u8 *__qrwlock_write_byte(struct qrwlock *lock)
{
return (u8 *)lock + 3 * IS_BUILTIN(CONFIG_CPU_BIG_ENDIAN);
}
Problem is many of the fixed big endian architectures don't define
CPU_BIG_ENDIAN and clears the wrong byte.
Define CPU_BIG_ENDIAN for all the fixed big endian architecture to fix it.
Also found few more references of this config parameter in
drivers/of/base.c
drivers/of/fdt.c
drivers/tty/serial/earlycon.c
drivers/tty/serial/serial_core.c
Be aware that this may cause regressions if someone has worked-around
problems in the above code already. Remove the work-around.
Here is our original discussion
https://lkml.org/lkml/2017/5/24/620
Link: http://lkml.kernel.org/r/1499358861-179979-2-git-send-email-babu.moger@oracle.com
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge updates from Andrew Morton:
- various misc bits
- DAX updates
- OCFS2
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (119 commits)
mm,fork: introduce MADV_WIPEONFORK
x86,mpx: make mpx depend on x86-64 to free up VMA flag
mm: add /proc/pid/smaps_rollup
mm: hugetlb: clear target sub-page last when clearing huge page
mm: oom: let oom_reap_task and exit_mmap run concurrently
swap: choose swap device according to numa node
mm: replace TIF_MEMDIE checks by tsk_is_oom_victim
mm, oom: do not rely on TIF_MEMDIE for memory reserves access
z3fold: use per-cpu unbuddied lists
mm, swap: don't use VMA based swap readahead if HDD is used as swap
mm, swap: add sysfs interface for VMA based swap readahead
mm, swap: VMA based swap readahead
mm, swap: fix swap readahead marking
mm, swap: add swap readahead hit statistics
mm/vmalloc.c: don't reinvent the wheel but use existing llist API
mm/vmstat.c: fix wrong comment
selftests/memfd: add memfd_create hugetlbfs selftest
mm/shmem: add hugetlbfs support to memfd_create()
mm, devm_memremap_pages: use multi-order radix for ZONE_DEVICE lookups
mm/vmalloc.c: halve the number of comparisons performed in pcpu_get_vm_areas()
...
Introduce MADV_WIPEONFORK semantics, which result in a VMA being empty
in the child process after fork. This differs from MADV_DONTFORK in one
important way.
If a child process accesses memory that was MADV_WIPEONFORK, it will get
zeroes. The address ranges are still valid, they are just empty.
If a child process accesses memory that was MADV_DONTFORK, it will get a
segmentation fault, since those address ranges are no longer valid in
the child after fork.
Since MADV_DONTFORK also seems to be used to allow very large programs
to fork in systems with strict memory overcommit restrictions, changing
the semantics of MADV_DONTFORK might break existing programs.
MADV_WIPEONFORK only works on private, anonymous VMAs.
The use case is libraries that store or cache information, and want to
know that they need to regenerate it in the child process after fork.
Examples of this would be:
- systemd/pulseaudio API checks (fail after fork) (replacing a getpid
check, which is too slow without a PID cache)
- PKCS#11 API reinitialization check (mandated by specification)
- glibc's upcoming PRNG (reseed after fork)
- OpenSSL PRNG (reseed after fork)
The security benefits of a forking server having a re-inialized PRNG in
every child process are pretty obvious. However, due to libraries
having all kinds of internal state, and programs getting compiled with
many different versions of each library, it is unreasonable to expect
calling programs to re-initialize everything manually after fork.
A further complication is the proliferation of clone flags, programs
bypassing glibc's functions to call clone directly, and programs calling
unshare, causing the glibc pthread_atfork hook to not get called.
It would be better to have the kernel take care of this automatically.
The patch also adds MADV_KEEPONFORK, to undo the effects of a prior
MADV_WIPEONFORK.
This is similar to the OpenBSD minherit syscall with MAP_INHERIT_ZERO:
https://man.openbsd.org/minherit.2
[akpm@linux-foundation.org: numerically order arch/parisc/include/uapi/asm/mman.h #defines]
Link: http://lkml.kernel.org/r/20170811212829.29186-3-riel@redhat.com
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: Colm MacCártaigh <colm@allcosts.net>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Cc: <linux-api@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A non-default huge page size can be encoded in the flags argument of the
mmap system call. The definitions for these encodings are in arch
specific header files. However, all architectures use the same values.
Consolidate all the definitions in the primary user header file
(uapi/linux/mman.h). Include definitions for all known huge page sizes.
Use the generic encoding definitions in hugetlb_encode.h as the basis
for these definitions.
Link: http://lkml.kernel.org/r/1501527386-10736-3-git-send-email-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
Pull parisc updates from Helge Deller:
"Major changes include:
- Full support of the firmware Page Deallocation Table with
MADV_HWPOISON and MADV_SOFT_OFFLINE. A kernel thread scans
regularily for new bad memory pages.
- Full support for self-extracting kernel.
- Added UBSAN support.
- Lots of section mismatch fixes across all parisc drivers.
- Added examples for %pF and %pS usage in printk-formats.txt"
* 'parisc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (28 commits)
printk-formats.txt: Add examples for %pF and %pS usage
parisc: Fix up devices below a PCI-PCI MegaRAID controller bridge
parisc/core: Fix section mismatches
parisc/ipmi_si_intf: Fix section mismatches on parisc platform
parisc/input/hilkbd: Fix section mismatches
parisc/net/lasi_82596: Fix section mismatches
parisc/serio: Fix section mismatches in gscps2 and hp_sdc drivers
parisc: Fix section mismatches in parisc core drivers
parisc/parport_gsc: Fix section mismatches
parisc/scsi/lasi700: Fix section mismatches
parisc/scsi/zalon: Fix section mismatches
parisc/8250_gsc: Fix section mismatches
parisc/mux: Fix section mismatches
parisc/sticore: Fix section mismatches
parisc/harmony: Fix section mismatches
parisc: Wire up support for self-extracting kernel
parisc: Make existing core files reuseable for bootloader
parisc: Add core code for self-extracting kernel
parisc: Enable UBSAN support
parisc/random: Add machine specific randomness
...
Pull locking updates from Ingo Molnar:
- Add 'cross-release' support to lockdep, which allows APIs like
completions, where it's not the 'owner' who releases the lock, to be
tracked. It's all activated automatically under
CONFIG_PROVE_LOCKING=y.
- Clean up (restructure) the x86 atomics op implementation to be more
readable, in preparation of KASAN annotations. (Dmitry Vyukov)
- Fix static keys (Paolo Bonzini)
- Add killable versions of down_read() et al (Kirill Tkhai)
- Rework and fix jump_label locking (Marc Zyngier, Paolo Bonzini)
- Rework (and fix) tlb_flush_pending() barriers (Peter Zijlstra)
- Remove smp_mb__before_spinlock() and convert its usages, introduce
smp_mb__after_spinlock() (Peter Zijlstra)
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
locking/lockdep/selftests: Fix mixed read-write ABBA tests
sched/completion: Avoid unnecessary stack allocation for COMPLETION_INITIALIZER_ONSTACK()
acpi/nfit: Fix COMPLETION_INITIALIZER_ONSTACK() abuse
locking/pvqspinlock: Relax cmpxchg's to improve performance on some architectures
smp: Avoid using two cache lines for struct call_single_data
locking/lockdep: Untangle xhlock history save/restore from task independence
locking/refcounts, x86/asm: Disable CONFIG_ARCH_HAS_REFCOUNT for the time being
futex: Remove duplicated code and fix undefined behaviour
Documentation/locking/atomic: Finish the document...
locking/lockdep: Fix workqueue crossrelease annotation
workqueue/lockdep: 'Fix' flush_work() annotation
locking/lockdep/selftests: Add mixed read-write ABBA tests
mm, locking/barriers: Clarify tlb_flush_pending() barriers
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE and CONFIG_LOCKDEP_COMPLETIONS truly non-interactive
locking/lockdep: Explicitly initialize wq_barrier::done::map
locking/lockdep: Rename CONFIG_LOCKDEP_COMPLETE to CONFIG_LOCKDEP_COMPLETIONS
locking/lockdep: Reword title of LOCKDEP_CROSSRELEASE config
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE part of CONFIG_PROVE_LOCKING
locking/refcounts, x86/asm: Implement fast refcount overflow protection
locking/lockdep: Fix the rollback and overwrite detection logic in crossrelease
...
This patch removes CONFIG_NETFILTER_DEBUG and _ASSERT() macros as they
are no longer required. Replace _ASSERT() macros with WARN_ON().
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is code duplicated over all architecture's headers for
futex_atomic_op_inuser. Namely op decoding, access_ok check for uaddr,
and comparison of the result.
Remove this duplication and leave up to the arches only the needed
assembly which is now in arch_futex_atomic_op_inuser.
This effectively distributes the Will Deacon's arm64 fix for undefined
behaviour reported by UBSAN to all architectures. The fix was done in
commit 5f16a046f8 (arm64: futex: Fix undefined behaviour with
FUTEX_OP_OPARG_SHIFT usage). Look there for an example dump.
And as suggested by Thomas, check for negative oparg too, because it was
also reported to cause undefined behaviour report.
Note that s390 removed access_ok check in d12a29703 ("s390/uaccess:
remove pointless access_ok() checks") as access_ok there returns true.
We introduce it back to the helper for the sake of simplicity (it gets
optimized away anyway).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Acked-by: Chris Metcalf <cmetcalf@mellanox.com> [for tile]
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Reviewed-by: Will Deacon <will.deacon@arm.com> [core/arm64]
Cc: linux-mips@linux-mips.org
Cc: Rich Felker <dalias@libc.org>
Cc: linux-ia64@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: peterz@infradead.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: sparclinux@vger.kernel.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux-s390@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: linux-hexagon@vger.kernel.org
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-xtensa@linux-xtensa.org
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: openrisc@lists.librecores.org
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Stafford Horne <shorne@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-parisc@vger.kernel.org
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-alpha@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20170824073105.3901-1-jslaby@suse.cz
Add some machine-specific information like values of cr16 cycle counter,
machine-specific software ID and machine model to the random generator.
Signed-off-by: Helge Deller <deller@gmx.de>
We only need to switch contexts when prev != next, and we don't need to
disable interrupts to do the check.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds