This patch causes the proper attribute flags to be set,
in the case that IPv6 UDP checksums are disabled, so that
userspace ie. `ip l2tp show tunnel` knows about it.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only set L2TP_ATTR_UDP_CSUM in l2tp_nl_tunnel_send()
when it's running over IPv4.
This prepares the code to also have IPv6 specific attributes.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving a GSO packet in dev_gro_receive() is not uncommon
in stacked devices, or devices partially implementing LRO/GRO
like bnx2x. GRO is implementing the aggregation the device
was not able to do itself.
Current code causes reorders, like in following case :
For a given flow where sender sent 3 packets P1,P2,P3,P4
Receiver might receive P1 as a single packet, stored in GRO engine.
Then P2-P4 are received as a single GSO packet, immediately given to
upper stack, while P1 is held in GRO engine.
This patch will make sure P1 is given to upper stack, then P2-P4
immediately after.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tunnel set action supports only IP addresses and key
options. Add UDP dst port option.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dst port parameter to __ip_tun_set_dst and __ipv6_tun_set_dst
utility functions.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IP tunneling classification supports only IP addresses and key.
Enhance UDP based IP tunneling classification parameters by adding UDP
src and dst port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When encapsulation field is set, mark it as used key for the flow
dissector. This will be used by offloading drivers.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed for drivers to pick the relevant action when offloading tunnel
key act.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this check, it is not possible to create two rules that
are identical except for their UID ranges. For example:
root@net-test:/# ip rule add prio 1000 lookup 300
root@net-test:/# ip rule add prio 1000 uidrange 100-200 lookup 300
RTNETLINK answers: File exists
root@net-test:/# ip rule add prio 1000 uidrange 100-199 lookup 100
root@net-test:/# ip rule add prio 1000 uidrange 200-299 lookup 200
root@net-test:/# ip rule add prio 1000 uidrange 300-399 lookup 100
RTNETLINK answers: File exists
Tested: https://android-review.googlesource.com/#/c/299980/
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had various problems in the past in tcp_get_info() and used
specific synchronization to avoid deadlocks.
We would like to add more instrumentation points for TCP, and
avoiding grabing socket lock in tcp_getinfo() was too costly.
Being able to lock the socket allows to provide consistent set
of fields.
inet_diag_dump_icsk() can make sure ehash locks are not
held any more when tcp_get_info() is called.
We can remove syncp added in commit d654976cbf
("tcp: fix a potential deadlock in tcp_get_info()"), but we need
to use lock_sock_fast() instead of spin_lock_bh() since TCP input
path can now be run from process context.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being lockless in tcp_get_info() is hard, because we need to add
specific synchronization in TCP fast path, like seqcount.
Following patch will change inet_diag_dump_icsk() to no longer
hold any lock for non listeners, so that we can properly acquire
socket lock in get_tcp_info() and let it return more consistent counters.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The for() loop in rds_tcp_accept_one() assumes that the 0'th
rds_tcp_conn_path is UP and starts multipath accepts at index 1.
But this assumption may not always be true: if the 0'th path
has failed (ERROR or DOWN state) an incoming connection request
should be used to resurrect this path.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket argument passed to rds_tcp_tc_info() is a PF_RDS socket,
so it is incorrect to report the address port info based on
rds_getname() as part of TCP state report.
Invoke inet_getname() for the t_sock associated with the
rds_tcp_connection instead.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set sk_err when dequeuing errors from the error queue.
Doing so results in:
a) Bugs: By overwriting existing sk_err values, it possibly
hides legitimate errors. It is also incorrect when local
errors are queued with ip_local_error. That happens in the
context of a system call, which already returns the error
code.
b) Inconsistent behavior: When there are pending errors on
the error queue, sk_err is sometimes 0 (e.g., for
the first timestamp on the error queue) and sometimes
set to an error code (after dequeuing the first
timestamp).
c) Suboptimality: Setting sk_err to ENOMSG on simple
TX timestamps can abort parallel reads and writes.
Removing this line doesn't break userspace. This is because
userspace code cannot rely on sk_err for detecting whether
there is something on the error queue. Except for ICMP messages
received for UDP and RAW, sk_err is not set at enqueue time,
and as a result sk_err can be 0 while there are plenty of
errors on the error queue.
For ICMP packets in UDP and RAW, sk_err is set when they are
enqueued on the error queue, but that does not result in aborting
reads and writes. For such cases, sk_err is only readable via
getsockopt(SO_ERROR) which will reset the value of sk_err on
its own. More importantly, prior to this patch,
recvmsg(MSG_ERRQUEUE) has a race on setting sk_err (i.e.,
sk_err is set by sock_dequeue_err_skb without atomic ops or
locks) which can store 0 in sk_err even when we have ICMP
messages pending. Removing this line from sock_dequeue_err_skb
eliminates that race.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a clear misconfiguration to attach a qdisc to a device with
tx_queue_len zero, because some qdisc's (namely, pfifo, bfifo, gred,
htb, plug and sfb) inherit/copy this value as their queue length.
Why should the kernel catch such a misconfiguration? Because prior to
introducing the IFF_NO_QUEUE device flag, userspace found a loophole
in the qdisc config system that allowed them to achieve the equivalent
of IFF_NO_QUEUE, which is to remove the qdisc code path entirely from
a device. The loophole on older kernels is setting tx_queue_len=0,
*prior* to device qdisc init (the config time is significant, simply
setting tx_queue_len=0 doesn't trigger the loophole).
This loophole is currently used by Docker[1] to get better performance
and scalability out of the veth device. The Docker developers were
warned[1] that they needed to adjust the tx_queue_len if ever
attaching a qdisc. The OpenShift project didn't remember this warning
and attached a qdisc, this were caught and fixed in[2].
[1] https://github.com/docker/libcontainer/pull/193
[2] https://github.com/openshift/origin/pull/11126
Instead of fixing every userspace program that used this loophole, and
forgot to reset the tx_queue_len, prior to attaching a qdisc. Let's
catch the misconfiguration on the kernel side.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag IFF_NO_QUEUE marks virtual device drivers that doesn't need a
default qdisc attached, given they will be backed by physical device,
that already have a qdisc attached for pushback.
It is still supported to attach a qdisc to a IFF_NO_QUEUE device, as
this can be useful for difference policy reasons (e.g. bandwidth
limiting containers). For this to work, the tx_queue_len need to have
a sane value, because some qdiscs inherit/copy the tx_queue_len
(namely, pfifo, bfifo, gred, htb, plug and sfb).
Commit a813104d92 ("IFF_NO_QUEUE: Fix for drivers not calling
ether_setup()") caught situations where some drivers didn't initialize
tx_queue_len. The problem with the commit was choosing 1 as the
fallback value.
A qdisc queue length of 1 causes more harm than good, because it
creates hard to debug situations for userspace. It gives userspace a
false sense of a working config after attaching a qdisc. As low
volume traffic (that doesn't activate the qdisc policy) works,
like ping, while traffic that e.g. needs shaping cannot reach the
configured policy levels, given the queue length is too small.
This patch change the value to DEFAULT_TX_QUEUE_LEN, given other
IFF_NO_QUEUE devices (that call ether_setup()) also use this value.
Fixes: a813104d92 ("IFF_NO_QUEUE: Fix for drivers not calling ether_setup()")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default TX queue length of Ethernet devices have been a magic
constant of 1000, ever since the initial git import.
Looking back in historical trees[1][2] the value used to be 100,
with the same comment "Ethernet wants good queues". The commit[3]
that changed this from 100 to 1000 didn't describe why, but from
conversations with Robert Olsson it seems that it was changed
when Ethernet devices went from 100Mbit/s to 1Gbit/s, because the
link speed increased x10 the queue size were also adjusted. This
value later caused much heartache for the bufferbloat community.
This patch merely moves the value into a defined constant.
[1] https://git.kernel.org/cgit/linux/kernel/git/davem/netdev-vger-cvs.git/
[2] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/
[3] https://git.kernel.org/tglx/history/c/98921832c232
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new argument is added to __skb_recv_datagram to provide
an explicit skb destructor, invoked under the receive queue
lock.
The UDP protocol uses such argument to perform memory
reclaiming on dequeue, so that the UDP protocol does not
set anymore skb->desctructor.
Instead explicit memory reclaiming is performed at close() time and
when skbs are removed from the receive queue.
The in kernel UDP protocol users now need to call a
skb_recv_udp() variant instead of skb_recv_datagram() to
properly perform memory accounting on dequeue.
Overall, this allows acquiring only once the receive queue
lock on dequeue.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr sinks vanilla patched
1 440 560
3 2150 2300
6 3650 3800
9 4450 4600
12 6250 6450
v1 -> v2:
- do rmem and allocated memory scheduling under the receive lock
- do bulk scheduling in first_packet_length() and in udp_destruct_sock()
- avoid the typdef for the dequeue callback
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it even after orphaining the skbuff.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding a raw socket to a local address fails if the socket is bound
to an L3 domain:
$ vrf-test -s -l 10.100.1.2 -R -I red
error binding socket: 99: Cannot assign requested address
Update raw_bind to look consider if sk_bound_dev_if is bound to an L3
domain and use inet_addr_type_table to lookup the address.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Define a new FIB rule attributes, FRA_UID_RANGE, to describe a
range of UIDs.
- Define a RTA_UID attribute for per-UID route lookups and dumps.
- Support passing these attributes to and from userspace via
rtnetlink. The value INVALID_UID indicates no UID was
specified.
- Add a UID field to the flow structures.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol sockets (struct sock) don't have UIDs, but most of the
time, they map 1:1 to userspace sockets (struct socket) which do.
Various operations such as the iptables xt_owner match need
access to the "UID of a socket", and do so by following the
backpointer to the struct socket. This involves taking
sk_callback_lock and doesn't work when there is no socket
because userspace has already called close().
Simplify this by adding a sk_uid field to struct sock whose value
matches the UID of the corresponding struct socket. The semantics
are as follows:
1. Whenever sk_socket is non-null: sk_uid is the same as the UID
in sk_socket, i.e., matches the return value of sock_i_uid.
Specifically, the UID is set when userspace calls socket(),
fchown(), or accept().
2. When sk_socket is NULL, sk_uid is defined as follows:
- For a socket that no longer has a sk_socket because
userspace has called close(): the previous UID.
- For a cloned socket (e.g., an incoming connection that is
established but on which userspace has not yet called
accept): the UID of the socket it was cloned from.
- For a socket that has never had an sk_socket: UID 0 inside
the user namespace corresponding to the network namespace
the socket belongs to.
Kernel sockets created by sock_create_kern are a special case
of #1 and sk_uid is the user that created them. For kernel
sockets created at network namespace creation time, such as the
per-processor ICMP and TCP sockets, this is the user that created
the network namespace.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support matching on SCTP ports in the same way that matching
on TCP and UDP ports is already supported.
Example usage:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 ip_proto sctp dst_port 80 \
action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP6CB and IPCB have a frag_max_size field. In IPv6 this field is
filled in when packets are reassembled by the connection tracking
code. Also fill in when reassembling in the input path, to expose
it through cmsg IPV6_RECVFRAGSIZE in all cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading a datagram or raw packet that arrived fragmented, expose
the maximum fragment size if recorded to allow applications to
estimate receive path MTU.
At this point, the field is only recorded when ipv6 connection
tracking is enabled. A follow-up patch will record this field also
in the ipv6 input path.
Tested using the test for IP_RECVFRAGSIZE plus
ip netns exec to ip addr add dev veth1 fc07::1/64
ip netns exec from ip addr add dev veth0 fc07::2/64
ip netns exec to ./recv_cmsg_recvfragsize -6 -u -p 6000 &
ip netns exec from nc -q 1 -u fc07::1 6000 < payload
Both with and without enabling connection tracking
ip6tables -A INPUT -m state --state NEW -p udp -j LOG
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP stack records the largest fragment of a reassembled packet
in IPCB(skb)->frag_max_size. When reading a datagram or raw packet
that arrived fragmented, expose the value to allow applications to
estimate receive path MTU.
Tested:
Sent data over a veth pair of which the source has a small mtu.
Sent data using netcat, received using a dedicated process.
Verified that the cmsg IP_RECVFRAGSIZE is returned only when
data arrives fragmented, and in that cases matches the veth mtu.
ip link add veth0 type veth peer name veth1
ip netns add from
ip netns add to
ip link set dev veth1 netns to
ip netns exec to ip addr add dev veth1 192.168.10.1/24
ip netns exec to ip link set dev veth1 up
ip link set dev veth0 netns from
ip netns exec from ip addr add dev veth0 192.168.10.2/24
ip netns exec from ip link set dev veth0 up
ip netns exec from ip link set dev veth0 mtu 1300
ip netns exec from ethtool -K veth0 ufo off
dd if=/dev/zero bs=1 count=1400 2>/dev/null > payload
ip netns exec to ./recv_cmsg_recvfragsize -4 -u -p 6000 &
ip netns exec from nc -q 1 -u 192.168.10.1 6000 < payload
using github.com/wdebruij/kerneltools/blob/master/tests/recvfragsize.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I managed to miss that sk_for_each is called under "for"
cycle so need to use goto here to return matching socket.
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Ahern <dsa@cumulusnetworks.com>
CC: Andrey Vagin <avagin@openvz.org>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In raw_diag_destroy the helper raw_sock_get returns
with sock_hold call, so we have to put it then.
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Ahern <dsa@cumulusnetworks.com>
CC: Andrey Vagin <avagin@openvz.org>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit ca26893f05 ("rhashtable: Add rhlist interface")
added a field to rhashtable_iter so that length became 56 bytes
and would exceed the size of args in netlink_callback (which is
48 bytes). The netlink diag dump function already has been
allocating a iter structure and storing the pointed to that
in the args of netlink_callback. ila_xlat also uses
rhahstable_iter but is still putting that directly in
the arg block. Now since rhashtable_iter size is increased
we are overwriting beyond the structure. The next field
happens to be cb_mutex pointer in netlink_sock and hence the crash.
Fix is to alloc the rhashtable_iter and save it as pointer
in arg.
Tested:
modprobe ila
./ip ila add loc 3333:0:0:0 loc_match 2222:0:0:1,
./ip ila list # NO crash now
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While being preparing patches for killing raw sockets via
diag netlink interface I noticed that my runs are stuck:
| [root@pcs7 ~]# cat /proc/`pidof ss`/stack
| [<ffffffff816d1a76>] __lock_sock+0x80/0xc4
| [<ffffffff816d206a>] lock_sock_nested+0x47/0x95
| [<ffffffff8179ded6>] udp_disconnect+0x19/0x33
| [<ffffffff8179b517>] raw_abort+0x33/0x42
| [<ffffffff81702322>] sock_diag_destroy+0x4d/0x52
which has not been the case before. I narrowed it down to the commit
| commit 286c72deab
| Author: Eric Dumazet <edumazet@google.com>
| Date: Thu Oct 20 09:39:40 2016 -0700
|
| udp: must lock the socket in udp_disconnect()
where we start locking the socket for different reason.
So the raw_abort escaped the renaming and we have to
fix this typo using __udp_disconnect instead.
Fixes: 286c72deab ("udp: must lock the socket in udp_disconnect()")
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Ahern <dsa@cumulusnetworks.com>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrey Vagin <avagin@openvz.org>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding sctp gso, sctp_packet_transmit is a quite big function now.
This patch is to extract the codes for packing packet to sctp_packet_pack
from sctp_packet_transmit, and add some comments, simplify the err path by
freeing auth chunk when freeing packet chunk_list in out path and freeing
head skb early if it fails to pack packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move common code from fl_delete and fl_detroy to __fl_delete.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_unbind was called in fl_delete but was missing in fl_destroy when
force deleting flows.
Fixes: 77b9900ef5 ('tc: introduce Flower classifier')
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. This includes better integration with the routing subsystem for
nf_tables, explicit notrack support and smaller updates. More
specifically, they are:
1) Add fib lookup expression for nf_tables, from Florian Westphal. This
new expression provides a native replacement for iptables addrtype
and rp_filter matches. This is more flexible though, since we can
populate the kernel flowi representation to inquire fib to
accomodate new usecases, such as RTBH through skb mark.
2) Introduce rt expression for nf_tables, from Anders K. Pedersen. This
new expression allow you to access skbuff route metadata, more
specifically nexthop and classid fields.
3) Add notrack support for nf_tables, to skip conntracking, requested by
many users already.
4) Add boilerplate code to allow to use nf_log infrastructure from
nf_tables ingress.
5) Allow to mangle pkttype from nf_tables prerouting chain, to emulate
the xtables cluster match, from Liping Zhang.
6) Move socket lookup code into generic nf_socket_* infrastructure so
we can provide a native replacement for the xtables socket match.
7) Make sure nfnetlink_queue data that is updated on every packets is
placed in a different cache from read-only data, from Florian Westphal.
8) Handle NF_STOLEN from nf_tables core, also from Florian Westphal.
9) Start round robin number generation in nft_numgen from zero,
instead of n-1, for consistency with xtables statistics match,
patch from Liping Zhang.
10) Set GFP_NOWARN flag in skbuff netlink allocations in nfnetlink_log,
given we retry with a smaller allocation on failure, from Calvin Owens.
11) Cleanup xt_multiport to use switch(), from Gao feng.
12) Remove superfluous check in nft_immediate and nft_cmp, from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment indicates, the data at the end of nfqnl_instance struct is
written on every queue/dequeue, so it should reside in its own cacheline.
Before this change, 'lock' was in first cacheline so we dirtied both.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After call nft_data_init, size is already validated and desc.len will
not exceed the sizeof(struct nft_data), i.e. 16 bytes. So it will never
exceed U8_MAX.
Furthermore, in nft_immediate_init, we forget to call nft_data_uninit
when desc.len exceeds U8_MAX, although this will not happen, but it's
a logical mistake.
Now remove these redundant validation introduced by commit 36b701fae1
("netfilter: nf_tables: validate maximum value of u32 netlink attributes")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduces an nftables rt expression for routing related data with support
for nexthop (i.e. the directly connected IP address that an outgoing packet
is sent to), which can be used either for matching or accounting, eg.
# nft add rule filter postrouting \
ip daddr 192.168.1.0/24 rt nexthop != 192.168.0.1 drop
This will drop any traffic to 192.168.1.0/24 that is not routed via
192.168.0.1.
# nft add rule filter postrouting \
flow table acct { rt nexthop timeout 600s counter }
# nft add rule ip6 filter postrouting \
flow table acct { rt nexthop timeout 600s counter }
These rules count outgoing traffic per nexthop. Note that the timeout
releases an entry if no traffic is seen for this nexthop within 10 minutes.
# nft add rule inet filter postrouting \
ether type ip \
flow table acct { rt nexthop timeout 600s counter }
# nft add rule inet filter postrouting \
ether type ip6 \
flow table acct { rt nexthop timeout 600s counter }
Same as above, but via the inet family, where the ether type must be
specified explicitly.
"rt classid" is also implemented identical to "meta rtclassid", since it
is more logical to have this match in the routing expression going forward.
Signed-off-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move layer 2 packet logging into nf_log_l2packet() that resides in
nf_log_common.c, so this can be shared by both bridge and netdev
families.
This patch adds the boiler plate code to register the netdev logging
family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add FIB expression, supported for ipv4, ipv6 and inet family (the latter
just dispatches to ipv4 or ipv6 one based on nfproto).
Currently supports fetching output interface index/name and the
rtm_type associated with an address.
This can be used for adding path filtering. rtm_type is useful
to e.g. enforce a strong-end host model where packets
are only accepted if daddr is configured on the interface the
packet arrived on.
The fib expression is a native nftables alternative to the
xtables addrtype and rp_filter matches.
FIB result order for oif/oifname retrieval is as follows:
- if packet is local (skb has rtable, RTF_LOCAL set, this
will also catch looped-back multicast packets), set oif to
the loopback interface.
- if fib lookup returns an error, or result points to local,
store zero result. This means '--local' option of -m rpfilter
is not supported. It is possible to use 'fib type local' or add
explicit saddr/daddr matching rules to create exceptions if this
is really needed.
- store result in the destination register.
In case of multiple routes, search set for desired oif in case
strict matching is requested.
ipv4 and ipv6 behave fib expressions are supposed to behave the same.
[ I have collapsed Arnd Bergmann's ("netfilter: nf_tables: fib warnings")
http://patchwork.ozlabs.org/patch/688615/
to address fallout from this patch after rebasing nf-next, that was
posted to address compilation warnings. --pablo ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix to return a negative error code from the idr_alloc() error handling
case instead of 0, as done elsewhere in this function.
Also fix the return value check of idr_alloc() since idr_alloc return
negative errors on failure, not zero.
Fixes: 2ae0f17df1 ("genetlink: use idr to track families")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable support for IPv4 multicast:
- similar to unicast the flow struct is updated to L3 master device
if relevant prior to calling fib_rules_lookup. The table id is saved
to the lookup arg so the rule action for ipmr can return the table
associated with the device.
- ip_mr_forward needs to check for master device mismatch as well
since the skb->dev is set to it
- allow multicast address on VRF device for Rx by checking for the
daddr in the VRF device as well as the original ingress device
- on Tx need to drop to __mkroute_output when FIB lookup fails for
multicast destination address.
- if CONFIG_IP_MROUTE_MULTIPLE_TABLES is enabled VRF driver creates
IPMR FIB rules on first device create similar to FIB rules. In
addition the VRF driver does not divert IPv4 multicast packets:
it breaks on Tx since the fib lookup fails on the mcast address.
With this patch, ipmr forwarding and local rx/tx work.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we create a new tipc socket state TIPC_CONNECTING
by primarily replacing the SS_CONNECTING with TIPC_CONNECTING.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we replace the references to SS_DISCONNECTING with
the combination of sk_state TIPC_DISCONNECTING and flags set in
sk_shutdown.
We introduce a new function _tipc_shutdown(), which provides
the common code required by tipc_release() and tipc_shutdown().
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we create a new tipc socket state TIPC_DISCONNECTING in
sk_state. TIPC_DISCONNECTING is replacing the socket connection status
update using SS_DISCONNECTING.
TIPC_DISCONNECTING is set for connection oriented sockets at:
- tipc_shutdown()
- connection probe timeout
- when we receive an error message on the connection.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we create a new tipc socket state TIPC_OPEN in
sk_state. We primarily replace the SS_UNCONNECTED sock->state with
TIPC_OPEN.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, tipc maintains probing state for connected sockets in
tsk->probing_state variable.
In this commit, we express this information as socket states and
this remove the variable. We set probe_unacked flag when a probe
is sent out and reset it if we receive a reply. Instead of the
probing state TIPC_CONN_OK, we create a new state TIPC_ESTABLISHED.
There is no functional change in this commit.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Asbjørn Sloth Tønnesen