The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_TPS65090
drivers/mfd/Kconfig: bool "TI TPS65090 Power Management chips"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_SYSCON
drivers/mfd/Kconfig: bool "System Controller Register R/W Based on Regmap"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_STA2X11
drivers/mfd/Kconfig: bool "STMicroelectronics STA2X11"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_RC5T583
drivers/mfd/Kconfig: bool "Ricoh RC5T583 Power Management system device"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_MAX8925
drivers/mfd/Kconfig: bool "Maxim Semiconductor MAX8925 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig for this option is currently:
config HTC_I2CPLD
bool "HTC I2C PLD chip support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_DB8500_PRCMU
drivers/mfd/Kconfig: bool "ST-Ericsson DB8500 Power Reset Control Management Unit"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_AS3711
drivers/mfd/Kconfig: bool "AMS AS3711"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Makefile/Kconfig currently controlling compilation of this code is:
drivers/mfd/Makefile:obj-$(CONFIG_PMIC_ADP5520) += adp5520.o
drivers/mfd/Kconfig:config PMIC_ADP5520
drivers/mfd/Kconfig: bool "Analog Devices ADP5520/01 MFD PMIC Core Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_AAT2870_CORE
drivers/mfd/Kconfig: bool "AnalogicTech AAT2870"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros-ec-vbc driver is DT-only and there is a DT property that
indicates if the EC has the VCB NVRAM, in such case instantiate the
driver but don't instantiate on the other cases.
To do this move the check code to its parent instead of play with the
attribute group visibility. This changes a bit the actual behaviour.
Before the patch if an EC doesn't have a VBC NVRAM an empty vbc folder
is created in /sys/class/chromeos/<ec-device-name>, after the patch the
empty folder is not created, so, the folder is only created if the vbc
is set.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros debugfs attibutes are created is broken.
cros_ec_sysfs should be its own driver and its attributes should be
associated with the sysfs driver not the mfd driver.
The patch also adds the sysfs documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros debugfs attibutes are created is broken.
cros_ec_debugfs should be its own driver and its attributes should be
associated with a debugfs driver not the mfd driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros sysfs attibutes are created is broken.
cros_ec_vbc should be its own driver and its attributes should be
associated with a vbc driver not the mfd driver. In order to retain
the path, the vbc attributes are attached to the cros_class.
The patch also adds the sysfs documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros sysfs attibutes are created is broken.
cros_ec_lightbar should be its own driver and its attributes should be
associated with a lightbar driver not the mfd driver. In order to retain
the path, the lightbar attributes are attached to the cros_class.
The patch also adds the sysfs documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() for adding cros-ec core MFD child devices. This
reduces the need of remove callback from platform/chrome for removing the
MFD child devices.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After commit 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set") dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly.
WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
Selected by [y]:
- MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y
MFD_TPS68470 is an ACPI only device and selects I2C_DESIGNWARE_PLATFORM.
I2C_DESIGNWARE_PLATFORM does not have any configuration today for ACPI
support without CONFIG_PCI set.
For sake of a quick fix this introduces a new mandatory dependency to
the driver which may survive without it. Otherwise we need to revisit
the driver architecture to address this properly.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
STPMIC1 is a PMIC from STMicroelectronics. The STPMIC1 integrates 10
regulators, 3 power switches, a watchdog and an input for a power on key.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This prepares the MFD for the STMPE ADC driver. This commit introduces
devicetree settings that are used by the ADC and adds an init function.
Common ADC settings that are shared with the touchscreen driver can now
reside in the overlying MFD.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
- Fix-ups
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
- Bug Fixes
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev
-----BEGIN PGP SIGNATURE-----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=BwG/
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
Fix-ups:
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
Bug Fixes:
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev"
* tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (25 commits)
mfd: exynos-lpass: Enable UART module support
mfd: mc13xxx: Fix a missing check of a register-read failure
mfd: cros_ec: Add commands to control codec
mfd: madera: Remove spurious semicolon in while loop
mfd: rave-sp: Fix typo in rave_sp_checksum comment
mfd: ingenic-tcu: Fix bit field description in header
mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()
mfd: Use of_node_name_eq() for node name comparisons
mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove
mfd: axp20x: Add supported cells for AXP803
mfd: axp20x: Re-align MFD cell entries
mfd: axp20x: Add AC power supply cell for AXP813
mfd: wm5110: Add missing ASRC rate register
mfd: qcom_rpm: write fw_version to CTRL_REG
mfd: tps6586x: Handle interrupts on suspend
mfd: madera: Add shared data for accessory detection
mfd: at91-usart: Add platform dependency
mfd: bd9571mwv: Add volatile register to make DVFS work
mfd: ab8500-core: Return zero in get_register_interruptible()
mfd: tmio: Typo s/use use/use/
...
This provides a free software alternative to raspberrypi-power.c's
firmware calls to manage power domains. It also exposes a reset line,
where previously the vc4 driver had to try to force power off the
domain in order to trigger a reset.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
The PM block that the wdt driver was binding to actually has multiple
features we want to expose (power domains, reset, watchdog). Move the
DT attachment to a MFD driver and make WDT probe against MFD.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
This patch enables proper interrupts routing between UART module
in Exynos Audio SubSystem and the rest of the SoC. This routing is
completely transparent for UART device and CPU/GIC. UART driver requests
interrupts from the respective controller and enables/masks/handles it
by itself via standard methods.
There are boards (for example TM2), which use UART module in Exynos Audio
SubStem for communication with BlueTooth chip.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
[mszyprow: rephrased commit message, added UART reset]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When mc13xxx_reg_read() fails, "old_adc0" is uninitialized and will
contain random value. Further execution uses "old_adc0" even when
mc13xxx_reg_read() fails.
The fix checks the return value of mc13xxx_reg_read(), and exits
the execution when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Coccinelle warning of a spurious semicolon on the closing brace
of a while loop.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_regmap_add_irq_chip and clean up error path in probe
and also the remove function.
Reported-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert string compares of DT node names to use of_node_name_eq() helper
instead. This removes direct access to the node name pointer.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver adds different MFD child devices via mfd_add_devices() and
hence it is required to call mfd_remove_devices() to remove MFD child
devices.
Fixes: 5e0115581b ("cros_ec: Move cros_ec_dev module to drivers/mfd")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Parts of the AXP803 are compatible with their counterparts on the AXP813.
These include the GPIO, ADC, AC and battery power supplies.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the axp20x driver, the various mfd_cell lists had varying amounts
of indentation, sometimes even within the same list. For the axp288,
there's no alignment at all.
Re-align the right hand side of the assignments with the least amount
of tabs possible. Also collapse the closing bracket and the opening
bracket of the next entry onto the same line for the axp288, to be
consistent with all the other mfd_cell lists.
This patch is whitespace change only. No functionality is modified.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As axp20x-ac-power-supply now supports AXP813, add a cell for it.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is required as part of the initialization sequence on certain SoCs.
If these registers are not initialized, the hardware can be unresponsive.
This fixes the driver on apq8060 (HP TouchPad device).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The tps6586x driver creates an irqchip that is used by its various child
devices for managing interrupts. The tps6586x-rtc device is one of its
children that uses the tps6586x irqchip. When using the tps6586x-rtc as
a wake-up device from suspend, the following is seen:
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
Disabling non-boot CPUs ...
Entering suspend state LP1
Enabling non-boot CPUs ...
CPU1 is up
tps6586x 3-0034: failed to read interrupt status
tps6586x 3-0034: failed to read interrupt status
The reason why the tps6586x interrupt status cannot be read is because
the tps6586x interrupt is not masked during suspend and when the
tps6586x-rtc interrupt occurs, to wake-up the device, the interrupt is
seen before the i2c controller has been resumed in order to read the
tps6586x interrupt status.
The tps6586x-rtc driver sets it's interrupt as a wake-up source during
suspend, which gets propagated to the parent tps6586x interrupt.
However, the tps6586x-rtc driver cannot disable it's interrupt during
suspend otherwise we would never be woken up and so the tps6586x must
disable it's interrupt instead.
Prevent the tps6586x interrupt handler from executing on exiting suspend
before the i2c controller has been resumed by disabling the tps6586x
interrupt on entering suspend and re-enabling it on resuming from
suspend.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add variables to struct madera that will be shared by the
extcon and audio codec drivers to synchronize output state
during accessory detection. Also add a mutex to protect
the DAPM pointer.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It doesn't make sense to present option MFD_AT91_USART by default if
not building an AT91 kernel, as the drivers which depend on it are
not available.
Fixes: 7d3aa342ce ("mfd: at91-usart: Add MFD driver for USART")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Because BD9571MWV_DVFS_MONIVDAC is not defined in the volatile table,
the physical register value is not updated by regmap and DVFS doesn't
work as expected. Fix it!
Fixes: d3ea212720 ("mfd: Add ROHM BD9571MWV-M MFD PMIC driver")
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[wsa: rebase, add 'Fixes', reword commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This function is supposed to return zero on success or negative error
codes on error. Unfortunately, there is a bug so it sometimes returns
non-zero, positive numbers on success.
I noticed this bug during review and I can't test it. It does appear
that the return is sometimes propogated back to _regmap_read() where all
non-zero returns are treated as failure so this may affect run time.
Fixes: 47c1697508 ("mfd: Align ab8500 with the abx500 interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the PMIC ID is unknown, the current code would call
irq_domain_remove and panic, as pmic->irq_domain is only
initialized by mt6397_irq_init.
Return immediately with an error, if the chip ID is unsupported.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building the kernel with Clang, the following section mismatch
warnings appear:
WARNING: vmlinux.o(.text+0x7239cc): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:init_prcm_registers()
The function db8500_prcmu_probe() references
the function __init init_prcm_registers().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of init_prcm_registers is wrong.
WARNING: vmlinux.o(.text+0x723e28): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:fw_project_name()
The function db8500_prcmu_probe() references
the function __init fw_project_name().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of fw_project_name is wrong.
db8500_prcmu_probe should not be marked as __init so remove the __init
annotation from fw_project_name and init_prcm_registers.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3d84a3b): Section mismatch in reference from
the function twl_probe() to the function
.init.text:unprotect_pm_master()
The function twl_probe() references
the function __init unprotect_pm_master().
This is often because twl_probe lacks a __init
annotation or the annotation of unprotect_pm_master is wrong.
Remove the __init annotation on the *protect_pm_master functions so
there is no more mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP20X_OFF define is an actual specific bit, define it as such.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the bitops.h header as we need it, alphabetize header order.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3aa2177e47.
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
------------[ cut here ]------------
Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
Modules linked in: btusb btrtl btintel btbcm bluetooth ...
CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
Hardware name: Google Kevin (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : device_release+0x80/0x90
lr : device_release+0x80/0x90
sp : ffff00000c47bc70
x29: ffff00000c47bc70 x28: ffff8000e86b0d40
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000056000000 x24: 0000000000000015
x23: ffff8000f0bbf860 x22: ffff000000d320a0
x21: ffff8000ee93e100 x20: ffff8000ed931428
x19: ffff8000ed931418 x18: 0000000000000020
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000400 x14: 0000000000000143
x13: 0000000000000000 x12: 0000000000000400
x11: 0000000000000157 x10: 0000000000000960
x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
x7 : 0000000000000000 x6 : ffff8000f7d520b8
x5 : ffff8000f7d520b8 x4 : 0000000000000000
x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
x1 : 37d859939c964800 x0 : 0000000000000000
Call trace:
device_release+0x80/0x90
kobject_put+0x74/0xe8
device_unregister+0x20/0x30
ec_device_remove+0x34/0x48 [cros_ec_dev]
platform_drv_remove+0x28/0x48
device_release_driver_internal+0x1a8/0x240
driver_detach+0x40/0x80
bus_remove_driver+0x54/0xa8
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
__arm64_sys_delete_module+0x16c/0x1f8
el0_svc_common+0x84/0xd8
el0_svc_handler+0x2c/0x80
el0_svc+0x8/0xc
---[ end trace a57c4625f3c60ae8 ]---
Cc: stable@vger.kernel.org
Fixes: 3aa2177e47 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use PLATFORM_DEVID_AUTO to number mfd cells while registering, so that
different instances are uniquely identified. This is required in order
to support registering of multiple instances of same ti_am335x_tscadc IP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Cc: patches@opensource.cirrus.com
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
* Move mfd/cros_ec_lpc* includes to drivers/platform from mfd
* Adding a new interrupt path for cros_ec_lpc
-----BEGIN PGP SIGNATURE-----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=cmQo
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome-platform updates from Benson Leung:
- Move mfd/cros_ec_lpc* includes to drivers/platform from mfd
- Adding a new interrupt path for cros_ec_lpc
* tag 'tag-chrome-platform-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: chromeos_tbmc - Remove unneeded const
platform/chrome: Add a new interrupt path for cros_ec_lpc
mfd: cros_ec: Fix and improve kerneldoc comments.
platform/chrome: Move mfd/cros_ec_lpc* includes to drivers/platform.
Clang warns:
drivers/mfd/cros_ec_dev.c:509:40: warning: variable 'cros_ec_id' is not
needed and will not be emitted [-Wunneeded-internal-declaration]
static const struct platform_device_id cros_ec_id[] = {
^
1 warning generated.
Avoid this warning by adding it to the cros_ec_dev_driver definition
under the id_table member like all other platform drivers.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace of_match_device() with of_device_get_match_data(), which
slightly decreases lines of code and allows to move the DT table
next to the I2C table.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This replaces all remaining unmanaged resources with device
managed ones, so that the remove function is no longer needed.
This makes the code slightly shorter and fixes two problems:
1. The hardware is disabled after the child devices have
been removed. Previously there was a potential race
condition.
2. The hardware is disabled when mfd_add_devices fails
during probe.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use new descriptor based API instead of the legacy one.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add const attribute to all mfd_cell structures.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Disable IRQs during suspend/resume cycle to ensure handling of wakeup
interrupts (i.e. RTC wake alarm) after max8997_resume(). This way it can
be properly handled when I2C bus is finally available. This pattern is
also used in other MAX PMIC MFD drivers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
IRQ wake up support for MAX8997 driver was initially configured by
respective property in pdata. However, after the driver conversion to
device-tree, setting it was left as 'todo'. Nowadays most of other PMIC MFD
drivers initialized from device-tree assume that they can be an irq wakeup
source, so enable it also for MAX8997. This fixes support for wakeup from
MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't populate the array mclk_name on the stack but instead make it
static. Makes the object code smaller by 23 bytes:
Before:
text data bss dec hex filename
38050 11604 64 49718 c236 linux/drivers/mfd/arizona-core.o
After:
text data bss dec hex filename
38027 11604 64 49695 c21f linux/drivers/mfd/arizona-core.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
1;5201;0c
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Sort headers alphabetically for better maintenance.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Power button IRQ actually has a second level of interrupts to
distinguish between UI and POWER buttons. Moreover, current
implementation looks awkward in approach to handle second level IRQs by
first level related IRQ chip.
To address above issues, split power button IRQ to be chained as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of open coding each data structure with regmap IRQresources,
use dedicated macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of open coding each data structure with IRQ resources,
use dedicated macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of open coding each data structure with IRQ resources,
use dedicated macro.
In one case use DEFINE_RES_IRQ_NAMED() and DEFINE_RES_MEM_NAMED().
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the audio-codec node by converting from
devm_of_platform_populate() to devm_mfd_add_devices().
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When trying to read any MC13892 ADC channel on a imx51-babbage board:
The MC13892 PMIC shutdowns completely.
After debugging this issue and comparing the MC13892 and MC13783
initializations done in the vendor kernel, it was noticed that the
CHRGRAWDIV bit of the ADC0 register was not being set.
This bit is set by default after power on, but the driver was
clearing it.
After setting this bit it is possible to read the ADC values correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
While polling for BOOT_DONE the chip could NAK a read because it is
still booting, which would terminate the regmap_read_poll_timeout()
with an error.
Instead implement a polling loop that ignores read errors so we
always poll until the chip signals boot or the loop times out.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't call runtime_put_sync when clk32k_ref is ARIZONA_32KZ_MCLK2
as there is no corresponding runtime_get_sync call.
MCLK1 is not in the AoD power domain so if it is used as 32kHz clock
source we need to hold a runtime PM reference to keep the device from
going into low power mode.
Fixes: cdd8da8cc6 ("mfd: arizona: Add gating of external MCLKn clocks")
Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently on every resume we check for mkbp events and notify the
clients. This helps in identifying the wakeup sources. But on devices
that do not support mkbp protocol, we might end up querying key state of
the keyboard in a loop which blocks the resume. Instead check for events
only if mkbp is supported.
Signed-off-by: RaviChandra Sadineni <ravisadineni@chromium.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The main MFD driver for Samsung PMICs (S2MPSXX, S5M876X) used with
Exynos SoCs can be compiled and used as a module. The dependent clock,
regulator and RTC drivers already can be built as a module.
Building entire set of drivers as modules might require using initial
ramdisk and can make booting process longer (due to probe deferrals).
However adding such option is useful for testing and for multi-platform
configurations.
This also add required module authors to sec-irq.c file based on recent
main contributors.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The indentation should be a tab followed by two spaces.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the GPIO
descriptor API, there's a small addition to the GPIO API plus a bunch of
updates to board files to implement it. This is some really welcome
work from Linus Walleij that's had a bunch of review and has been
sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvNyl0THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DubB/4nWL/XSUb7qIm2fjjMUffelfk4/viB
MZg3JPEMr7ahK+QC1RQ5nOmkuACSU3Uij8RE1omLp5isfCiSa+e17f9uQx4Cn/pw
9DsIeJUEC4LvZ9gA9pDf0313B/0BIYfOMJToyLgwTNmJl+T+0e59RcS4TTCEqxwD
PmpPakOvCTD6YuVI7HhYL/HXJK1buvrAiENSjCyfyJTDaMSzJl6WMn+eibFaZbDn
NXwj2W+QyuiFCdl/7/4NWaqhlyOvM05ivnnLM/SPMBj+Iu4gSZ0PX81z98eZ3M66
YSPhF2o5SkhhffFx5xjpgR3VquXDVb0oefzhvJmZYHXi7ZKKMruoYaGB
=Ztu3
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the
GPIO descriptor API, there's a small addition to the GPIO API plus a
bunch of updates to board files to implement it. This is some really
welcome work from Linus Walleij that's had a bunch of review and has
been sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices"
* tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: lochnagar: Use a consisent comment style for SPDX header
regulator: bd718x7: Remove struct bd718xx_pmic
regulator: Fetch enable gpiods nonexclusive
regulator/gpio: Allow nonexclusive GPIO access
regulator: lochnagar: Add support for the Cirrus Logic Lochnagar
regulator: stpmic1: Return REGULATOR_MODE_INVALID for invalid mode
regulator: stpmic1: add stpmic1 regulator driver
dt-bindings: regulator: document stpmic1 pmic regulators
regulator: axp20x: Mark expected switch fall-throughs
regulator: bd718xx: fix build warning on x86_64
regulator: fixed: Default enable high on DT regulators
regulator: bd718xx: rename bd71837 to 718xx
regulator: bd718XX use pickable ranges
regulator/mfd: bd718xx: rename bd71837/bd71847 common instances
regulator: Support regulators where voltage ranges are selectable
mfd: dt bindings: add BD71847 device-tree binding documentation
regulator: dt bindings: add BD71847 device-tree binding documentation
regulator/mfd: Support ROHM BD71847 power management IC
regulator: da905{2,5}: Remove unnecessary array check
regulator: qcom: Add PMS405 regulators
...
If a child device like touchscreen is wakeup capable, then keep ADC
interface on, so that a touching resistive screen will generate wakeup
event to the system.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently tscadc MFD is marked as wakeup capable which incorrect
because, its actually touch event by child TSC device that wakes up the
system. Therefore, remove device_init_wakeup() call that marks TSCADC
device as wakeup capable in favor of moving to mark TSC input device as
wakeup capable later.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Casting address to unsigned int causes a warning on some 64 bit
architectures. Fix the cast.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename parts of code that support both BD71837 and BD71847 to BD718XX.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD71847 is reduced version of BD71837. DVS bucks 3 and 4 are
removed as is LDO7. Voltage ranges of some regulators are
expanded.
Add initial support for BD71847 with BD71837 driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.
I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IRQ work is added before the struct rtc is allocated and registered,
but this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before calling menelaus_add_irq_work.
Also, this solves a possible leak as the RTC is never released.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This MFD driver is just a wrapper over atmel_serial driver and
spi-at91-usart driver. Selection of one of the drivers is based on a
property from device tree. If the property is not specified, the default
driver is atmel_serial.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cros-ec includes inside the MFD subsystem, specially the file
cros_ec_commands.h, has been modified several times and it has grown a
lot, unfortunately, we didn't have care too much about the documentation.
This patch tries to improve the documentation and also fixes all the
issues reported by kerneldoc script.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
ROHM BD71837 PMIC MFD driver providing interrupts and support
for three subsystems:
- clk
- Regulators
- input/power-key
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of Device Tree platforms, even though the Samsung PMIC sec
device is instantiated from DT, the driver is still matched through I2C
module alias. That is because I2C core always reports an I2C module
alias instead of DT one.
This could change in the future so export DT module alias.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On ams AS3722, power on when AC OK is enabled by default.
Making this option as disable by default and enable only
when platform need this explicitly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
Tested-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Pine64 H64 board uses an AXP806 PMIC in I2C and self-working mode.
The H64 SoC does not have the usual RSB controller.
This patch adds AXP806 to the list of devices supported in I2C mode.
In theory, all RSB-based PMICs can also be used in I2C mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 can operate in a standalone "self-working" mode, in which it
is also responsible for power control of the overall system. This mode
is similar to the master mode, but the EN/PWRON pin functions as a power
button, instead of a level-triggered enable switch.
This patch adds code checking for the new "x-powers,self-working-mode"
property, and a separate mfd_cell list that includes the power button
(PEK) sub-device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For designs where CS/ADDR pin is floating, it is useful to
allow dts to define whether to keep internal pull down or not.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Configuring Speaker Mode Pullup was already supported in pdata, but not
in the dts.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CMD_GET_STATUS is not supported by some devices implementing
RDU2-compatible ICD as well as "legacy" devices. To account for that
fact, add code that obtains the same information (app/bootloader FW
version) using several different commands.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-wdt driver to properly ping the
watchdog on "legacy" firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-eeprom driver work on "legacy"
firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Relying on serial port defaults for flow control and parity can result
in complete breakdown of communication with RAVE SP on some platforms
where defaults are not what we need them to be. One such case is
VF610-base ZII SPU3 board (not supported upstream). To avoid this
problem in the future, add code to explicitly configure both.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove unusded defines that are a leftover from earlier iterations of
the driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes https://bugs.linaro.org/show_bug.cgi?id=3903
LTP Functional tests have caused a bad paging request when triggering
the regmap_read_debugfs() logic of the device PMIC Hi6553 (reading
regmap/f8000000.pmic/registers file during read_all test):
Unable to handle kernel paging request at virtual address ffff0
[ffff00000984e000] pgd=0000000077ffe803, pud=0000000077ffd803,0
Internal error: Oops: 96000007 [#1] SMP
...
Hardware name: HiKey Development Board (DT)
...
Call trace:
regmap_mmio_read8+0x24/0x40
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x170
regmap_read+0x50/0x78
regmap_read_debugfs+0x1a0/0x308
regmap_map_read_file+0x48/0x58
full_proxy_read+0x68/0x98
__vfs_read+0x48/0x80
vfs_read+0x94/0x150
SyS_read+0x6c/0xd8
el0_svc_naked+0x30/0x34
Code: aa1e03e0 d503201f f9400280 8b334000 (39400000)
Investigations have showed that, when triggered by debugfs read()
handler, the mmio regmap logic was reading a bigger (16k) register area
than the one mapped by devm_ioremap_resource() during hi655x-pmic probe
time (4k).
This commit changes hi655x's max register, according to HW specs, to be
the same as the one declared in the pmic device in hi6220's dts, fixing
the issue.
Cc: <stable@vger.kernel.org> #v4.9 #v4.14 #v4.16 #v4.17
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona CODECs have a small timing window where they will
NAK an I2C transaction if it happens before the boot done bit is
set. This can cause the read of the register containing the boot
done bit to fail until it is set. Since regmap_read_poll_timeout
will abort polling if a read fails it can't be reliably used to
poll the boot done bit over I2C.
Do a partial revert of ef84f885e0 ("mfd: arizona: Refactor
arizona_poll_reg"), removing the regmap_read_poll_timeout but
leaving the refactoring to make the arizona_poll_reg take more
sensible arguments.
Fixes: ef84f885e0 ("mfd: arizona: Refactor arizona_poll_reg")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Ice Lake has the same LPSS than Intel Cannon Lake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For some errors, the wm8994_device_init function was returning or
jumping to the wrong point in the error path.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add const to the declaration of various local variables of type
kempld_platform_data for which the referenced value is always only
dereferenced or passed to a const parameter, to record the fact that
kempld_platform_data_generic is declared as const.
The semantic match that finds this issue is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,j;
@@
const struct i j = { ... };
@ok@
identifier r.i;
position p;
@@
const struct i@p *
@@
identifier r.i;
position p != ok.p;
@@
* struct i@p *
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6gYDF28Li+nEiKLaHwn1ewov5lgFAltCtRsACgkQHwn1ewov
5lhIQg//fEoZkDIjFsWIDn2WB1brLS2q7Wnv01NJR3/ZxzA29JYQ1lNA3nCM5mVS
Bf1RqPfVwIO6/d+QA5AnxLBRpRYJ7F7NKwvTvrqQ9QpFPNOLk0m7uUNYSsWTOqlA
uoReeFfJ2/UuUavd04KJRPv1ilCjoki2Wyc4lqVFSJSGZZjDWUOASAiOd666h26F
avW4qBUpJm7mmAfOFh76g6c/Jq713fJkqfdRcstRajB13oLjotfRxa/Rhxb+y8aX
RrlNz8PChIjpYTQ7yDwfLU8u5TDg2sEtz8529YaddDNBWkRyC2BIrKrkev+GIiUx
SZiPT7nmvpEOGJoPQodUa5bgE/9db7pPKb7XqUNmYQIS71jtLaOXMNje9uLn2NHo
CJtoVHJXZ9YWyODn1NPvFM28aysis14PWQGWK1HRq5PCfb8TpZ8W0QTaJV18pUBe
vdrmgxPcdnkAn0Tbt92oBiUrsVT3zoSQuLw9FPuy3ne9Oz+TKHa6kKzjcMMkynwb
mFmDhf822mfbUVkjUpNTtLJ0UMsNtd/tphDUmv1OQDRNStZS/MI4+xr23bPZbf/X
blrIjz5fM6uhUbHSKztWnntGAtzbEy75zzyhh2w99JVzJtK4UK+3ET40Kko4KUIx
1ppYa2wOJVVSvd733O8mYGmzQotKuFc5lyNozlB4EUT8ro/zW1Q=
=EhHj
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
The EC can expose a CEC bus, thus add the cros-ec-cec MFD sub-device
when the CEC feature bit is present.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DA9063L, which is a reduced variant of the DA9063
with less regulators and without RTC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not contain RTC block, unlike the full DA9063.
Split the RTC block into separate mfd cell and register it only
on DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not have an RTC. Add custom IRQ map for DA9063L to
ignore the Alarm and Tick IRQs from the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not have an RTC. Add custom regmap for DA9063L to
prevent access into that register block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The model number stored in the struct da9063 is the same for all
variants of the da9063 since it is the chip ID, which is always
the same. Replace that with a separate identifier instead, which
allows us to discern the DA9063 variants by setting the type
based on either DT match or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC_DA9063 is a complete misnomer, it denotes the value of the
DA9063 chip ID register, so rename it as such. It is also the value
of chip ID register of DA9063L though, so drop the enum as all the
DA9063 "models" share the same chip ID and thus the distinction will
have to be made using DT or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace DA9063_NUM_IRQ macro which is not used anywhere with
plain ARRAY_SIZE().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use PLATFORM_DEVID_NONE instead of -1 in mfd_add_devices.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the regmap_irq table to use REGMAP_IRQ_REG().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the regmap_range tables to use regmap_reg_range() macro.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() instead of plain mfd_add_devices(), which
removes the need for da9063_device_exit() altogether and also for the
.remove callback in da9063-i2c.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_regmap_add_irq_chip() instead of plain regmap_add_irq_chip(),
which removes the need for da9063_irq_exit() altogether and also
fixes a bug in da9063_device_init() where the da9063_irq_exit() was
not called in a failpath.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Check whether this EC instance has USBPD host command support and
instatiate the cros_usbpd-charger driver as a subdevice in such case.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are some cros-ec transport drivers (I2C, SPI) living in MFD, while
others (LPC) living in drivers/platform. The transport drivers are more
platform specific. So, move the I2C and SPI transport drivers to the
platform/chrome directory. The patch also removes the MFD_ prefix of
their Kconfig symbols.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull i2c updates from Wolfram Sang:
- mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...)
- conversion to use the i2c_8bit_addr_from_msg macro consistently
- move includes to platform_data
- core updates to allow the (still in review) I3C subsystem to connect
- and the regular share of smaller driver updates
* 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits)
i2c: qup: fix building without CONFIG_ACPI
i2c: tegra: Remove suspend-resume
i2c: imx-lpi2c: Switch to SPDX identifier
i2c: mxs: Switch to SPDX identifier
i2c: busses: make use of i2c_8bit_addr_from_msg
i2c: algos: make use of i2c_8bit_addr_from_msg
i2c: rcar: document R8A77980 bindings
i2c: qup: Add command-line parameter to override SCL frequency
i2c: qup: Correct duty cycle for FM and FM+
i2c: qup: Add support for Fast Mode Plus
i2c: qup: add probe path for Centriq ACPI devices
i2c: robotfuzz-osif: drop pointless test
i2c: robotfuzz-osif: remove pointless local variable
i2c: rk3x: Don't print visible virtual mapping MMIO address
i2c: opal: don't check number of messages in the driver
i2c: ibm_iic: don't check number of messages in the driver
i2c: imx: Switch to SPDX identifier
i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data
i2c: mux: demux-pinctrl: use proper parent device for demux adapter
i2c: mux: improve error message for failed symlink
...
This function is no longer called, so we get a harmless
warning until it is removed as well:
drivers/mfd/cros_ec_dev.c:265:13: error: '__remove' defined but not used [-Werror=unused-function]
Fixes: 3aa2177e47 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is not mandatory that platform data is passed along the ac97
codec. Actually there are configuration without a battery connected to
the ADC of the codec.
This is for example the case for the PXA zylonite platform, so fix the
NULL dereferencing by adding a test.
Fixes: a5c6951c49 ("mfd: wm97xx-core: core support for wm97xx Codec")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned out
to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from Maciej
Purski, unfortunately there are further problems there so the last
couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW regulators
on Qualcomm SPMI and dropped support for some preproduction chips
that never made it to market from the AB8500 driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlsarcETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B4HB/9MFV/MK7Hw2hsVCX3qWTiH4tJ/X0MG
tGz1PfmbH0CJ9ly5g+rvCoT+1/s7BydKzi1cd1RHnimBv2U1XagwSny3LNEcJs2Q
pmhpGViakkQI/Y2h+u/j0Jk1nE+jTiKk+1ozUB7YnPekrGyQlf7TMhvKOLTvLKyX
56jdNxcW0MgSnXV2N6y4NpWhgvrQwvKjacTxV5iX7WP2rnK2WNFeG7Q859buhtI0
znRi+tO5hZsw5T44ickdPfotZn+i5o7MYLCkkaA2h1EwtpbYwVINfUjp3KtuyFhH
3B9GmCsjjN2Z2eInnkpzWfVXK2S1Vlp6+ka2FSs+U/4rVdd3Bw2KkblS
=Ftua
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned
out to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from
Maciej Purski, unfortunately there are further problems there so the
last couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW
regulators on Qualcomm SPMI and dropped support for some preproduction
chips that never made it to market from the AB8500 driver"
* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
regulator: gpio: Revert
ARM: pxa, regulator: fix building ezx e680
regulator: Revert coupled regulator support again
regulator: wm8994: Fix shared GPIOs
regulator: max77686: Fix shared GPIOs
regulator: bd71837: BD71837 PMIC regulator driver
regulator: bd71837: Devicetree bindings for BD71837 regulators
regulator: gpio: Get enable GPIO using GPIO descriptor
regulator: fixed: Convert to use GPIO descriptor only
regulator: s2mps11: Fix boot on Odroid XU3
dt-bindings: qcom_spmi: Document SAW support
regulator: qcom_spmi: Add support for SAW
regulator: tps65090: Pass descriptor instead of GPIO number
regulator: s5m8767: Pass descriptor instead of GPIO number
regulator: pfuze100: Delete reference to ena_gpio
regulator: max8952: Pass descriptor instead of GPIO number
regulator: lp8788-ldo: Pass descriptor instead of GPIO number
regulator: lm363x: Pass descriptor instead of GPIO number
regulator: max8973: Pass descriptor instead of GPIO number
regulator: mc13xxx-core: Switch to SPDX identifier
...
cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with.
Kudos to Laura Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare
dwapb driver.
Misc:
- Random cleanups, right header files in the drivers, some
size optimizations etc.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbGOMeAAoJEEEQszewGV1zGR0P/Rq/Mh6BRum7kZee8v22aKJE
imtSamaVk7eOSdLC00VLvJ5QYJBMWz2GV5ZJkaxAwHBh1GhfddTDj35uXoOkRRWs
vRXSYthujluGJ5YYfRNrXZhD4ahVYPnJV5XxLy4OF+aQBAd4jjRAqXLhQT1PVK9Q
AQD/BOjToxrjgPREaLX9sQTW8DbICmjRhEWieJoQab2mZC+qD/aCen0rkj+UD0Qu
wQRk5mSEsrC0qmWNS/rhzFa7/nRa4qWOMkHxim7/GqwGzgOTpv+TctmQOqMUjHqq
k0ikVgBfZbaz3MqcuqLbKJ00mRK6G/yQIlECP4xcMbxKRxXucJj1ytOedIdG4nJE
5porXbW1d1bIhv3Zv8tt7vh00x+mEF+hv6p8DUa9ppe7qwsdbhUdzeczeyR8eM7U
ZBi80jMJfp9wEugZ0F8syIUs3PPgp7y461hJDbZRuHp4P4jmpdUBMAF4XvWl6XPy
DAlPHnSc2ZNaqWJtfc1ja4e6DlwltEV81Sd9Y0clLhkD95k95gZ7EzoyGPAIO4FG
ir0getZE1mfh9K/EfkTOkcKHJh3b5rA5TiSbTVVaPO9SzqPtIK+xhDJI0r9IJkW1
XKgScOaJqpYEe2Y/Y/ezfnjxDLVxwOz6R77GsZCle1uPevOcxqN9fmjEn7gGYzmX
PDf5pOuRrWApqix4a3Jr
=Ly/0
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.18 development cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with. Kudos to Laura
Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare dwapb
driver.
Misc:
- Random cleanups, right header files in the drivers, some size
optimizations etc"
* tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpio: davinci: fix build warning when !CONFIG_OF
gpio: dwapb: Fix rework support for 1 interrupt per port A GPIO
gpio: pxa: Include the right header
gpio: pl061: Include the right header
gpio: pch: Include the right header
gpio: pcf857x: Include the right header
gpio: pca953x: Include the right header
gpio: palmas: Include the right header
gpio: omap: Include the right header
gpio: octeon: Include the right header
gpio: mxs: Switch to SPDX identifier
gpio: Remove VLA from stmpe driver
gpio: mxc: Switch to SPDX identifier
gpio: mxc: add clock operation
gpio: Remove VLA from gpiolib
gpio: aspeed: Use a cache of output data registers
gpio: aspeed: Set output latch before changing direction
gpio: pca953x: fix address calculation for pcal6524
gpio: pca953x: define masks for addressing common and extended registers
gpio: pca953x: set the PCA_PCAL flag also when matching by DT
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
Pull input updates from Dmitry Torokhov:
- a new driver to ChipOne icn8505 based touchscreens
- on certain systems with Elan touch controllers they will be switched
away form PS/2 emulation and over to native SMbus mode
- assorted driver fixups and improvements
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: elan_i2c - add ELAN0612 (Lenovo v330 14IKB) ACPI ID
Input: goodix - add new ACPI id for GPD Win 2 touch screen
Input: xpad - add GPD Win 2 Controller USB IDs
Input: ti_am335x_tsc - prevent system suspend when TSC is in use
Input: ti_am335x_tsc - ack pending IRQs at probe and before suspend
Input: cros_ec_keyb - mark cros_ec_keyb driver as wake enabled device.
Input: mk712 - update documentation web link
Input: atmel_mxt_ts - fix reset-gpio for level based irqs
Input: atmel_mxt_ts - require device properties present when probing
Input: psmouse-smbus - allow to control psmouse_deactivate
Input: elantech - detect new ICs and setup Host Notify for them
Input: elantech - add support for SMBus devices
Input: elantech - query the resolution in query_info
Input: elantech - split device info into a separate structure
Input: elan_i2c - add trackstick report
Input: usbtouchscreen - add sysfs attribute for 3M MTouch firmware rev
Input: ati_remote2 - fix typo 'can by' to 'can be'
Input: replace hard coded string with __func__ in pr_err()
Input: add support for ChipOne icn8505 based touchscreens
Input: gamecon - avoid using __set_bit() for capabilities
...
Regmap configuration tables for Cirrus Logic CS47L90 and CS47L91 codecs.
Signed-off-by: Nikesh Oswal <nikesh@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap configuration tables for Cirrus Logic CS47L85 codecs.
Signed-off-by: Nariman Poushin <nariman@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap configuration tables for Cirrus Logic CS47L35 codecs.
Signed-off-by: Piotr Stankiewicz <piotrs@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the generic core support for Cirrus Logic "Madera" class codecs.
These are complex audio codec SoCs with a variety of digital and analogue
I/O, onboard audio processing and DSPs, and other features.
These codecs are all based off a common set of hardware IP so can be
supported by a core of common code (with a few minor device-to-device
variations).
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- asus_atk0110 driver modified to use new API
- k10temp supports new CPUs and reports both Tctl and Tdie
- minor fixes in gpio-fan, ltc2990, fschmd, and mc13783 drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3w3p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- asus_atk0110 driver modified to use new API
- k10temp supports new CPUs and reports both Tctl and Tdie
- minor fixes in gpio-fan, ltc2990, fschmd, and mc13783 drivers
* tag 'hwmon-for-linus-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (asus_atk0110) Make use of device managed memory
hwmon: (asus_atk0110) Replace deprecated device register call
hwmon: (k10temp) Make function get_raw_temp static
hwmon: (gpio-fan) Fix "#cooling-cells" property name in bindings
MAINTAINERS: hwmon: Add Documentation/devicetree/bindings/hwmon
hwmon: (ltc2990) support all measurement modes
hwmon: (ltc2990) add devicetree binding
hwmon: (ltc2990) Fix incorrect conversion of negative temperatures
hwmon: (core) check parent dev != NULL when chip != NULL
hwmon: (fschmd) fix typo 'can by' to 'can be'
hwmon: (k10temp) Display both Tctl and Tdie
hwmon: (k10temp) Add support for Stoney Ridge and Bristol Ridge CPUs
hwmon: MC13783: Add uid and die temperature sensor inputs
Paul Gortmaker