Atlas Scientific DO-SM OEM sensor reads disolved oxygen in
a solution. This is reported back as mg/L which maps directly
to ppm and so the IIO_CONCENTRATION channel type can be used.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensors don't actually need a interrupt line to give valid readings,
and can triggered with CONFIG_IIO_HRTIMER_TRIGGER as well. Remove
the required check for interrupt, and continue along in the probe
function.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
SPS30 uses triggered buffer, but the dependency is not specified in the
Kconfig file. Fix this by selecting IIO_BUFFER and IIO_TRIGGERED_BUFFER
config symbols.
Cc: stable@vger.kernel.org
Fixes: 232e0f6dde ("iio: chemical: add support for Sensirion SPS30 sensor")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO triggered buffer depends on IIO buffer which is missing from Kconfig
file. This should go unnoticed most of the time because there's a
chance something else has already enabled buffers. In some rare cases
though one might experience kbuild warnings about unmet direct
dependencies and build failures due to missing symbols.
Fix this by selecting IIO_BUFFER explicitly.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Fixes: a1d642266c ("iio: chemical: add support for Plantower PMS7003 sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function to detect the number of channels to output
in trigger handler. This is based on IIO_TIMESTAMP channel being the
delimiter between input and output channels.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the orginal scope of the driver was to only support
the pH product from Atlas it has evolved to other sensors.
Rename the file, driver name, and regmap to atlas-sensor which
reflects this, although keep CONFIG_ATLAS_PH_SENSOR to not cause
regressions with current configurations.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver includes <linux/gpio.h> yet fails to use symbols
from any the header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When breaking up a constant to write to two 8 bit registers
it isn't obvious to sparse that it was intentional.
CHECK drivers/iio/chemical/sps30.c
drivers/iio/chemical/sps30.c:120:30: warning: cast truncates bits from constant value (8004 becomes 4)
So in the interests of minimising noisy warnings, let us add
a mask.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_predisable() should be called last, to detach the
poll func after the devices has been suspended.
The position of iio_triggered_buffer_postenable() is correct.
Note this is not stable material. It's a fix in the logical
model rather fixing an actual bug. These are being tidied up
throughout the subsystem to allow more substantial rework that
was blocked by variations in how things were done.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Formatting of Kconfig files doesn't look so pretty, so just
take damp cloth and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add other sensors to the compatible list.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Without IIO_TRIGGERED_BUFFER, this driver fails to link:
drivers/iio/chemical/pms7003.o: In function `pms7003_probe':
pms7003.c:(.text+0x21c): undefined reference to `devm_iio_triggered_buffer_setup'
pms7003.c:(.text+0x21c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_iio_triggered_buffer_setup'
Fixes: a1d642266c ("iio: chemical: add support for Plantower PMS7003 sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SPI interface implementation was completely broken.
When using the SPI interface, there are only 7 address bits, the upper bit
is controlled by a page select register. The core needs access to both
ranges, so implement register read/write for both regions. The regmap
paging functionality didn't agree with a register that needs to be read
and modified, so I implemented a custom paging algorithm.
This fixes that the device wouldn't even probe in SPI mode.
The SPI interface then isn't different from I2C, merged them into the core,
and the I2C/SPI named registers are no longer needed.
Implemented register value caching for the registers to reduce the I2C/SPI
data transfers considerably.
The calibration set reads as all zeroes until some undefined point in time,
and I couldn't determine what makes it valid. The datasheet mentions these
registers but does not provide any hints on when they become valid, and they
aren't even enumerated in the memory map. So check the calibration and
retry reading it from the device after each measurement until it provides
something valid.
Despite the size this is suitable for a stable backport given that
it seems the SPI support never worked.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The standard unit for temperature is millidegrees Celcius. Adapt the
driver to report in millidegrees instead of degrees.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I clearly messed up applying this patch. Not sure
how but the entire Kconfig block is missing. This
patch puts it back as it was in the original patch.
Reported-by: Andreas Brauchli <a.brauchli@elementarea.net>
Fixes: ce51412416 ("iio: chemical: sgp30: Support Sensirion SGP30/SGPC3 sensors")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
-----BEGIN PGP SIGNATURE-----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=Se+F
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for IIO in the 5.1 cycle.
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
* tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (26 commits)
iio: adc: exynos-adc: Use proper number of channels for Exynos4x12
dt-binding: iio: remove rst node from NPCM ADC document
dt-bindings: iio: chemical: pms7003: add device tree support
dt-bindings: add Plantower to the vendor prefixes
iio: chemical: add support for Plantower PMS7003 sensor
iio:chemical:sps30 Supress some switch fallthrough warnings.
iio:adc:lpc32xx use SPDX-License-Identifier
dt-bindings: iio: adc: move lpc32xx-adc out of staging
iio: adc: ads124s08: fix spelling mistake "converions" -> "conversions"
iio: adc: exynos-adc: Fix NULL pointer exception on unbind
iio: chemical: sps30: fix a loop timeout test
iio:accel:adxl345: Change alignment to match paranthesis
iio:dac:dac7612: device tree bindings
iio:dac:ti-dac7612: Add driver for Texas Instruments DAC7612
iio: adc: ad7476: Add support for TI ADS786X ADCs
iio: adc: ad7768-1: Add support for setting the sampling frequency
drivers: iio: dac: Fix wrong license for ADI drivers
IIO: add Ingenic JZ47xx ADC driver.
dt-bindings: iio/adc: Add bindings for Ingenic JZ47xx SoCs ADC.
dt-bindings: iio/adc: Add docs for Ingenic JZ47xx SoCs ADC.
...
Add support for Plantower PMS7003 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes warnings reported on linux-next but marking one path
and adding an explicit return in the other.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Brauchli <a.brauchli@elementarea.net>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
The "while (tries--) {" loop is a postop so it exits with "tries" set
to -1.
Fixes: 232e0f6dde ("iio: chemical: add support for Sensirion SPS30 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pr_fmt is used by printk wrappers. There are not any in the driver
code so remove the format specifier.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensor can periodically trigger self cleaning. Period can be changed by
writing a new value to a dedicated attribute. Upon attribute read
current period gets returned.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit allow the driver to work with device-tree.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@gmail.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO_TEMP scale value for temperature was incorrect and not in millicelsius
as required by the ABI documentation.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Fixes: 27dec00ecf (iio: chemical: add Atlas pH-SM sensor support)
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Self cleaning is especially useful in cases where sensor undergoes
frequent power on/off cycles. In such scenarios it is recommended to
turn self cleaning at least once per week in order to maintain reliable
measurements.
Self cleaning is activated by writing 1 to a dedicated attribute.
Internal fan accelerates to its maximum speed and keeps spinning
for about 10 seconds blowing out accumulated dust.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Tested-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support Sensirion SGP30 and SGPC3 multi-pixel I2C gas sensors
Supported Features:
* Indoor Air Quality (IAQ) concentrations for
- tVOC (in_concentration_voc_input)
- CO2eq (in_concentration_co2_input) - SGP30 only
IAQ concentrations are periodically read out by a background thread
to allow the sensor to maintain its internal baseline.
* Gas concentration signals
- Ethanol (in_concentration_ethanol_raw)
- H2 (in_concentration_h2_raw) - SGP30 only
https://www.sensirion.com/file/datasheet_sgp30https://www.sensirion.com/file/datasheet_sgpc3
Signed-off-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Sensirion SPS30 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove BME680_RUN_GAS_EN_BIT and BME680_NB_CONV_0_VAL field value
definitions because the fields are simply boolean and integer
respectively.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
val2 is responsible for the floating part of the number to be
written to the device. We don't need the floating part
while writing the oversampling ratio for BME680 since the
available oversampling ratios are pure natural numbers.
So, add a sanity check to make sure val2 is 0.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Temperature, pressure and humidity all expose and oversampling setting
that works in the same way. Provide common handling for the
oversampling sysfs attributes.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the FIELD_GET macro instead of explicit mask and shift.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert all defines to use "MASK" instead of a mix of "MSK" and "MASK"
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the full 80 char width to reduce the number of lines taken
by function calls.
Remove blank lines where it aids clarity by bringing together related
code blocks (such as read hi and low bytes and then combine them into
one value).
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Tested-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
fix spelling mistake in dev_err error message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Bosch BME680 is a 4-in-1 sensor with temperature, pressure, humidity
and gas sensing capability. It supports both I2C and SPI communication
protocol for effective data communication.
The device supports two modes:
1. Sleep mode
2. Forced mode
The measurements only takes place when forced mode is triggered and a
single TPHG cycle is performed by the sensor. The sensor automatically
goes to sleep after afterwards.
The device has various calibration constants/parameters programmed into
devices' non-volatile memory(NVM) during production and can't be altered
by the user. These constants are used in the compensation functions to
get the required compensated readings along with the raw data. The
compensation functions/algorithms are provided by Bosch Sensortec GmbH
via their API[1]. As these don't change during the measurement cycle,
therefore we read and store them at the probe. The default configs
supplied by Bosch are also set at probe.
0-day tested with build success.
GSoC-2018: https://summerofcode.withgoogle.com/projects/#6691473790074880
Mentor: Daniel Baluta
[1] https://github.com/BoschSensortec/BME680_driver
Datasheet:
https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BME680-DS001-00.pdf
Note from Jonathan: The compensation functions are 'interesting' and
could do with a tidy up in future. However, they work so we can leave that
for another day.
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
-----BEGIN PGP SIGNATURE-----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=egCX
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st round of IIO new device support, features and cleanup for the 4.18 cycle
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
usleep_range() uses hrtimers and provides no advantage over msleep()
for larger delays.
Cc: Nicholas Mc Guire <hofrat@osadl.org>
Link: http://lkml.org/lkml/2017/1/11/377
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
CCS811 has different I2C register maps in boot and application mode. When
CCS811 is in boot mode, register APP_START (0xF4) is used to transit the
firmware state from boot to application mode. However, APP_START is not a
valid register location when CCS811 is in application mode (refer to
"CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in
CCS811 datasheet). The driver should not attempt to perform a write to
APP_START while CCS811 is in application mode, as this is not a valid or
documented register location.
When prob function is being called, the driver assumes the CCS811 sensor
is in boot mode, and attempts to perform a write to APP_START. Although
CCS811 powers-up in boot mode, it may have already been transited to
application mode by previous instances, e.g. unload and reload device
driver by the system, or explicitly by user. Depending on the system
design, CCS811 sensor may be permanently connected to system power source
rather than power controlled by GPIO, hence it is possible that the sensor
is never power reset, thus the firmware could be in either boot or
application mode at any given time when driver prob function is being
called.
This patch checks the STATUS register before attempting to send a write to
APP_START. Only if the firmware is not in application mode and has valid
firmware application loaded, then it will continue to start transiting the
firmware boot to application mode.
Signed-off-by: Richard Lai <richard@richardman.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The resistance member in ccs811_reading struct is an unsigned 16-bit
integer variable used to store RAW_DATA register bytes read from CCS811.
It is kind of misleading to name this struct member as resistance.
About the RAW_DATA register bytes, the CCS811 datasheet states that:
-----
Two byte read only register which contains the latest readings from the
sense resistor.
The most significant 6 bits of the Byte 0 contain the value of the current
through the sensor (0μA to 63μA).
The lower 10 bits contain (as computed from the ADC) the readings of the
voltage across the sensor with the selected current (1023 = 1.65V)"
-----
Hence, the RAW_DATA register byte contains information about electric
current and voltage of the CCS811 sensor. Calling this struct member
'resistance' is kind of misleading, although both electric current and
voltage are needed to calculate the electrical resistance of the sensor
using Ohm's law, V = I x R, in which a new channel type of IIO_RESISTANCE
may be added to the driver in the future.
Signed-off-by: Richard Lai <richard@richardman.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add GPLv2+ SPDX identifier and update email for author's drivers.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Greg Kroah-Hartman