The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Follow-up to commit 294d31e822 ("sony-laptop: don't change keyboard
backlight settings"): avoid messing up the state on resume. Leave it to
what was before suspending as it's anyway likely that we still don't
know what value we should write to the EC registers. This fix is also
required in 3.12
Cc: stable@vger.kernel.org
Tested-by: Karol Babioch <karol@babioch.de>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c284ee2cf1. Turns out
the locking was incorrect.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Header file <acpi/acpi.h> contains environemnt settings and architecture
specific implementation that should be included before any other ACPICA
headers in order to keep a consistent build environment for ACPICA users.
The following internal ACPICA header files should be included from
<acpi/acpi.h> and should not be included by other kernel files:
<acpi/acpiosxf.h>
<acpi/acpixf.h>
Clean up incorrect inclusions of these files from non-ACPICA source
files.
[rjw: Subject and changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
MCPM code was changed in commit 0de0d64675 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
idlestates in sysfs are counted from 0.
This fixes a wrong error message.
Current behavior on a machine with 4 sleep states is:
cpupower idle-set -e 4
Idlestate 4 enabled on CPU 0
-----Wrong---------------------
cpupower idle-set -e 5
Idlestate enabling not supported by kernel
-----Must and now will be -----
cpupower idle-set -e 5
Idlestate 6 not available on CPU 0
-------------------------------
cpupower idle-set -e 6
Idlestate 6 not available on CPU 0
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpupower idle-set subcommand was introduce recently.
This patch provides the missing manpage.
If cpupower is properly installed it will show up automatically
(similar to git), when invoking:
cpupower help idle-set
or
cpupower idle-set --help
Some parts have been taken over and adjusted from
git commit 62d6ae880e
documentation submitted by Carsten Emde.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.
This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:
drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
zsmalloc encodes a handle using the pfn and an object
index. On hardware platforms with physical memory starting
at 0x0 the pfn can be 0. This causes the encoded handle to be
0 and is incorrectly interpreted as an allocation failure.
This issue affects all current and future SoCs with physical
memory starting at 0x0. All MSM8974 SoCs which includes
Google Nexus 5 devices are affected.
To prevent this false error we ensure that the encoded handle
will not be 0 when allocation succeeds.
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was introduced due to a patch hunk when porting
commit 20802057 (staging/lustre/ptlrpc: race in pinger).
Cc: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=cIMc
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 3.13 cycle.
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
A bunch of fixes, a few driver specific ones and a framework fix for
voltage enumeration on fixed voltage regulators which had previously
worked but had been misplaced during some refactoring causing problems
for users that needed to know the voltage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=2BEl
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of fixes, a few driver specific ones and a framework fix for
voltage enumeration on fixed voltage regulators which had previously
worked but had been misplaced during some refactoring causing problems
for users that needed to know the voltage"
* tag 'regulator-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: arizona-micsupp: Correct wm5110 voltage selection
regulator: pfuze100: allow misprogrammed ID
regulator: fixed: fix regulator_list_voltage() for regression
regulator: gpio-regulator: Don't oops on missing regulator-type property
drivers/staging/btmtk_usb/btmtk_usb.c: In function ‘btmtk_usb_probe’:
drivers/staging/btmtk_usb/btmtk_usb.c:1610: warning: assignment from incompatible pointer type
Add the new hdev parameter, cfr. commit
7bd8f09f69 ("Bluetooth: Add hdev parameter to
hdev->send driver callback").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up the remaining "dev is used before it is set" issues in the
go7007 driver that were originally caused by commit
b6ea5ef80a but not fixed up by reverting
it due to other patches later on adding these "fixes".
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Dulshani Gunawardhana <dulshani.gunawardhana89@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8d181e408 (staging: drm/imx: add drm plane support) added a file
to the make target for DRM_IMX_IPUV3 but didn't adjust the objs required
to actually build that as a module. Kbuild got confused and this lead to
link errors like:
ERROR: "ipu_plane_disable" [drivers/staging/imx-drm/ipuv3-crtc.ko] undefined!
ERROR: "ipu_plane_enable" [drivers/staging/imx-drm/ipuv3-crtc.ko] undefined!
Additionally, it added a call to imx_drm_crtc_id which also fails with a
link error as above. To fix this, we adjust the make target with the proper
objs, which will change the name of the resulting .ko. We also add an
EXPORT_SYMBOL_GPL for imx_drm_crtc_id.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Fixes: b8d181e408 '(staging: drm/imx: add drm plane support)'
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b6ea5ef80a.
Turns out to have lots of run-time issues in that the structure is not
initialized before it is used in the debugging messages.
Reported-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Dulshani Gunawardhana <dulshani.gunawardhana89@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With multiple, concurrent readers (each waiting to acquire the
atomic_read_lock mutex), a departing reader may mistakenly reset
minimum_to_wake after a new reader has already set a new value.
Protect the minimum_to_wake reset with the atomic_read_lock critical
section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Minchan Kim and Jerome Marchand "The code in reset_store
get the block device (bdget_disk()) but it does not put it (bdput()) when
it's done using it. The usage count is therefore incremented but never
decremented."
This patch also puts bdput() for all error cases.
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We assume nvec->rx can be NULL earlier so I have added a check here as
well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We fixed this to use free_netdev() instead of kfree() but unfortunately
free_netdev() doesn't accept NULL pointers. Smatch complains about
this, it's not something I discovered through testing.
Fixes: 3030d40b50 ('staging: vt6655: use free_netdev instead of kfree')
Fixes: 0a438d5b38 ('staging: vt6656: use free_netdev instead of kfree')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I broke `s626_set_dac()` by changing the type of the `dacdata` parameter
from `short` to `unsigned short`. It's actually designed to take a
signed value in the range -0x1fff to +0x2000 although values above
0x1fff get clamped to 0x1fff. (We could change the `maxdata` value to
0x1ffe to avoid the clamping, but `maxdata` values are usually a power
of 2 minus 1.) The bug results in all negative values passed to the
function being changed to +0x1fff by the clamp. Change the parameter
type to `int16_t` to fix the problem.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These conditions are never true because they use bitwise AND instead of
logical ands.
Fixes: b3ff824a81 ('staging: comedi: drivers: use comedi_dio_update_state() for complex cases')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If none of the if conditions take a true path, the ret variable will
never be assigned a value.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common security idiom is to hangup the current tty (via vhangup())
after forking but before execing a root shell. This hangs up any
existing opens which other processes may have and ensures subsequent
opens have the necessary permissions to open the root shell tty/pty.
Reset the TTY_HUPPED state after the driver has successfully
returned the opened tty (perform the reset while the tty is locked
to avoid racing with concurrent hangups).
Reported-by: Heorhi Valakhanovich <valahanovich@tut.by>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Tested-by: Heorhi Valakhanovich <valahanovich@tut.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Amiga with
"console=ttyS0" on the kernel command line, it crashes with:
Unable to handle kernel access at virtual address 81dff01c
Oops: 00000000
PC: [<001e09a8>] serial_console_write+0xc/0x70
Add the missing platform check to amiserial_console_init() to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Mac with "console=ttyS0"
on the kernel command line, it crashes with:
Unable to handle kernel NULL pointer dereference at virtual address (null)
Oops: 00000000
PC: [<0013ad28>] __pmz_startup+0x32/0x2a0
...
Call Trace: [<002c5d3e>] pmz_console_setup+0x64/0xe4
The normal tty driver doesn't crash, because init_pmz() checks
pmz_ports_count again after calling pmz_probe().
In the serial console initialization path, pmz_console_init() doesn't do
this, causing the driver to crash later.
Add a check for pmz_ports_count to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are not completed..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm spin lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), which is a tty framework api, and
this is the opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9326b047e4 includes a typo
of "8350_core" instead of "8250_core", so correct it.
Fixes kernel bugzilla #60724:
https://bugzilla.kernel.org/show_bug.cgi?id=60724
Reported-by: Christoph Biedl <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The asynchronous aborts are generally fatal for the kernel but they can
be masked via the pstate A bit. If a system error happens while in
kernel mode, it won't be visible until returning to user space. This
patch enables this kind of abort early to help identifying the cause.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the spin-table SMP booting method, secondary CPUs poll a location
passed in the DT. The foundation-v8.dts file doesn't have this memory
reserved and there is a risk of Linux using it before secondary CPUs are
started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit f27dde8dee (sched: Add NEED_RESCHED to the preempt_count)
introduced the use of bit 31 in preempt_count for obscure scheduling
purposes.
This causes interrupts taken from EL0 to hit the (open coded) BUG when
this flag is flipped while handling the interrupt (we compare the
values before and after, and kill the kernel if they are different).
The fix is to stop messing with the preempt count entirely, as this
is already being dealt with in the generic code (irq_enter/irq_exit).
Tested on a dual A53 FPGA running cyclictest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Although the maximum allowable canonical line is specified to
be 255 bytes (MAX_CANON), the practical limit has actually been
the size of the line discipline read buffer (N_TTY_BUF_SIZE == 4096).
Commit 32f13521ca,
n_tty: Line copy to user buffer in canonical mode, limited the
line copy to 4095 bytes. With a completely full line discipline
read buffer and a userspace buffer > 4095, _no_ data was copied,
and the read() syscall returned 0, indicating EOF.
Fix the interval arithmetic to compute the correct number of bytes
to copy to userspace in the range [1..4096].
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cbfd0340ae,
'n_tty: Process echoes in blocks', introduced an error when
consuming the echo buffer tail to prevent buffer overrun, where
the incorrect operation code byte is checked to determine how
far to advance the tail to the next echo byte.
Check the correct byte for the echo operation code byte.
Cc: <stable@vger.kernel.org> # 3.12.x : c476f65 tty: incorrect test of echo_buf() result for ECHO_OP_START
Cc: <stable@vger.kernel.org> # 3.12.x
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A departing reader must restart a flush_to_ldisc() worker _before_
the next reader enters the read loop; this is to avoid the new reader
concluding no more i/o is available and prematurely exiting, when the
old reader simply hasn't re-started the worker yet.
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change cifs.ko to using CIFS_IOCTL_COPYCHUNK instead
of BTRFS_IOC_CLONE to avoid confusion about whether
copy-on-write is required or optional for this operation.
SMB2/SMB3 copyoffload had used the BTRFS_IOC_CLONE ioctl since
they both speed up copy by offloading the copy rather than
passing many read and write requests back and forth and both have
identical syntax (passing file handles), but for SMB2/SMB3
CopyChunk the server is not required to use copy-on-write
to make a copy of the file (although some do), and Christoph
has commented that since CopyChunk does not require
copy-on-write we should not reuse BTRFS_IOC_CLONE.
This patch renames the ioctl to use a cifs specific IOCTL
CIFS_IOCTL_COPYCHUNK. This ioctl is particularly important
for SMB2/SMB3 since large file copy over the network otherwise
can be very slow, and with this is often more than 100 times
faster putting less load on server and client.
Note that if a copy syscall is ever introduced, depending on
its requirements/format it could end up using one of the other
three methods that CIFS/SMB2/SMB3 can do for copy offload,
but this method is particularly useful for file copy
and broadly supported (not just by Samba server).
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: David Disseldorp <ddiss@samba.org>
This patch defines a new value for the 'ima_show_type' enumerator
(IMA_SHOW_BINARY_NO_FIELD_LEN) to prevent that the field length
is transmitted through the 'binary_runtime_measurements' interface
for the digest field of the 'ima' template.
Fixes commit: 3ce1217 ima: define template fields library and new helpers
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
To maintain compatibility with userspace tools, the field length must not
be included in the template digest calculation for the 'ima' template.
Fixes commit: a71dc65 ima: switch to new template management mechanism
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Git commit 9e34f2686bb088b211b6cac8772e1f644c6180f8
"s390/mm,tlb: tlb flush on page table upgrade fixup" removed the
exception handler for the asce-type exception. This is incorrect
as the user-copy with MVCOS can cause asce-type exceptions in
the kernel if a user pointer is too large. Those need to be
handled with do_no_context to branch to the fixup in the
user-copy code.
The simplest fix for this problem is to call do_dat_exception for
asce-type excpetions, as there is no vma for the address the code
will handle the exception correctly.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git commit 4f37a68cda
"s390: Use direct ktime path for s390 clockevent device" makes use
of the CLOCK_EVT_FEAT_KTIME clockevent option to avoid the delta
calculation with ktime_get() in clockevents_program_event and the
get_tod_clock() in s390_next_event. This is based on the assumption
that the difference between the internal ktime and the hardware
clock is reflected in the wall_to_monotonic delta. But this is not
true, the ntp corrections are applied via changes to the tk->mult
multiplier and this is not reflected in wall_to_monotonic.
In theory this could be solved by using the raw monotonic clock
but it is simpler to switch back to the standard clock delta
calculation.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Switch to the improved update_vsyscall interface that provides
sub-nanosecond precision for gettimeofday and clock_gettime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stephen Warren