This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this function is used by most ath driver, so it can be moved here.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While registering the driver with cfg80211, update the threshold
value and retry limit to cfg80211.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes bug found by the kbuild test robot:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 1e2f9295f4
commit: 1cbbcb08c7 [135/140] wil6210: prefetch head of packet
config: make ARCH=microblaze allyesconfig
All error/warnings:
drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx':
>> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data);
^
cc1: some warnings being treated as errors
vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c
375 wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
376 kfree_skb(skb);
377 return NULL;
378 }
379 skb_trim(skb, dmalen);
380
> 381 prefetch(skb->data);
382
383 wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1,
384 skb->data, skb_headlen(skb), false);
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a possible overflow condition which results in occasional
bad IQ coefficients and EVM numbers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in the TX IQ calibration post
processing routine because of which the driver disables
TX IQ correction even though the calibration results
are valid. This fix is applicable for all chips in the
AR9003 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing the card the driver still tries to access registers
in the device. This patch adds another state for the bus that
indicates the device is no longer reachable. This avoids errors
accessing it while cleaning up the driver.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For scheduled scan results the driver does a escan to obtain BSS
details from the firmware. However, the escan uses a dynamically
determined function. This needs to be set appropriately when handling
scheduled scan results to avoid NULL pointer access.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework function to allow only bcm4329 in case of chip backplane
type being sonics sillicon backplane.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware download code has been restructured so the reset vector
does not need to be stored in a structure, but keep it on the stack
to be passed to exit download function.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original core reset and disable routines do not work always
on running system. These routines were updated to properly reset
a core. When module is unloaded the device is put into download
state where all necessary cores have been reset. This will make
sure the device is in idle mode after module unload.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New bus layers like pcie require nvram parsing routines which are
the same routines as being used by sdio. Make these routines common
in the new file nvram.c. Update sdio to use these routines and
simplify the nvram upload process. Also add memory validation check
for downloaded firmware and nvram in debug mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Discovered by klocwork
Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
* rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
* rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
* rs.c:2565: Array 'iwl_rate_mcs' size is 15.
* rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.
While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.
Fix it by incrementing the seq_number only later,
before saving it.
Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd471423 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: Alex Gal <a.gal@motsai.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new device IDs and assigning generic function/variable
names instead of using device-id specific names.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.
This fixes this warning:
[ 5.488733] ath: phy0: ASPM enabled: 0x43
[ 5.488735] ath: EEPROM regdomain: 0x0
[ 5.488736] ath: EEPROM indicates default country code should be used
[ 5.488736] ath: doing EEPROM country->regdmn map search
[ 5.488737] ath: country maps to regdmn code: 0x3a
[ 5.488737] ath: Country alpha2 being used: US
[ 5.488738] ath: Regpair used: 0x3a
[ 5.488738] ------------[ cut here ]------------
[ 5.488745] WARNING: CPU: 0 PID: 161 at
/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[ 5.488746] wiphy should have REGULATORY_CUSTOM_REG
The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we disassociate in managed mode, we flush the queues
after mac80211 has already removed the station.
During that time, the pointer to ieee80211_sta to the
fw_id_to_mac_id map is -EINVAL. In that case we should not
set the station as being drained when the last Tx of this
station has exited the shared Tx queue since we are
flushing all the queues anyway.
The draining logic is meant to be used in GO / AP mode only.
In GO / AP mode, we set -EBUSY in the fw_id_to_mac_id map.
This is why testing the ieee80211_sta pointer in the
fw_id_to_mac_id map with IS_ERR isn't enough to set the
station as draining, we need to check that it is -EBUSY.
The only impact of the bug was a print:
Drained sta 1, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
If we can't switch to a column because no rates are supported
in that column this led to a state where the search cycle
got stuck and never ended. This in turn also led to aggregation
not being turned on. Fix this by marking a column as
visited if we can't switch to it.
Reported-and-tested-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The power settings need to be updated after a binding flow is done
and before quota calculations. This was missing in the start_ap_ibss()
flow. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The state variable was not set to false in case of a failure to
complete the start_ap_ibss() flow.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Restore the original regulatory testing functionality and also
make it more flexible by allowing the parameters to be specified
when creating a dynamic radio.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new commands to the hwsim generic netlink family to allow
creating and destroying radios on the fly. The number of channels
a radio supports can be specified when it's created, if it isn't
the module parameter will be used as default.
This should be extended in the future to allow other parameters
to be specified, e.g.
* list of channels
* interface combinations, particularly P2P_DEVICE support
* regtest
* and pretty much all other hardware capabilities
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reject wmediumd registrations when any devices have multi-channel
capability, but register the generic netlink family unconditionally
to make it possible to add new commands that shouldn't depend on
the number of (default) channels.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There can't be two wmediumd instances controlling hwsim,
so reject registration from a second one and verify in
the commands that it's the correct instance calling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will make the next patch, adding support for netlink,
smaller and more readable. The code is not modified here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To later allow dynamic registration, assign the index for the
struct device and MAC address from a new free-running counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the flag that the module parameter sets instead, so
later radios can use different parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the radio cleanup into a new function to later
allow deleting a single radio from the list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support dynamic radio registration in the future,
refactor the actual registration into a new function with only
minor cleanups. Since it had to change anyway, also clean up
the init error paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regtest thing worked based on the radio loop, but with
more dynamic radio registration that loop won't really exist
as is. We can add it back later with proper dynamic code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepare the code to support, in theory, different devices
with a different number of channels supported. Right now
this doesn't really change anything, but will allow for
dynamic device registration in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to print a message, and genl_unregister_family()
can't really fail so remove the error message there as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.
Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9
iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps
iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add Kconfig option that allow DFS functionality.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add new AR9565 1.0/1.0.1/1.1 IDs
* Change Dell/Lenovo/Samsung cards to 2-Antenna with diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having two copies of the code for device tree cfgdata
downloading, add a function to improve the code.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfgdata length exceeds the command buffer size we will end up
getting buffer overflow problem. Fix it by checking the buffer
size less the command header length.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for the bcm43362 1x1 11n chipset. This
chipset is used in AP6210 wifi module found on Cubieboard [1].
[1] http://cubieboard.org/
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nvs file name to module firmware list
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Oleksij Rempel