Remove unnecessary set of flag IFF_MULTICAST, since ether_setup
already does this.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't be within an RCU read-side critical section when deleting
VLANs, as underlying drivers might sleep during the hardware operation.
Therefore, replace the RCU critical section with a mutex. This is
consistent with team_vlan_rx_add_vid.
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the underlying device supports offloads encapulated traffic,
we need to reflect that through the hw_enc_features field of the
team net-device.
This will cause the xmit path in the core networking stack to provide
team with encapsulated GSO frames to offload into the HW etc.
Using this over Mellanox ConnectX3-pro (mlx4 driver) card that supports
VXLAN offloads we got 36.0 Gbits/sec using eight iperf streams.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let netdev notifier listeners know about link-up and port-enable state
changes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During options set, there will be needed to hold rtnl_mutex in order to
safely call netdev notifiers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize netdev_lag_upper_info structure by TX type according to
current team mode and pass it along via netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate netdev_master_upper_dev_link_private and pass priv directly as
a parameter of netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other helpers, caller can use this to find out if device is
team master.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- introduce port fdb obj and generic switchdev_port_fdb_add/del/dump()
- use switchdev_port_fdb_add/del/dump in rocker/team/bonding ndo ops.
- add support for fdb obj in switchdev_port_obj_add/del/dump()
- switch rocker to implement fdb ops via switchdev_ops
v3: updated to sync with named union changes.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa said remove the feature flag for this series and she'll work on
bringing it back if needed at a later date.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker, bonding and team and switch over to the new
switchdev_port_bridge_dellink to avoid duplicating code in each driver.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker, bonding, and team can now use the switchdev bridge setlink to parse
raw netlink; no need to duplicate this code in each driver.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Team devices don't need to segment multiple tagged packets since their
slaves can segment them.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows TSO being set/unset on the master, so that GSO
segmentation is done after team layer.
Similar patch is present for bonding:
b0ce3508b2 ("bonding: allow TSO being set on bonding master")
and bridge:
f902e8812e ("bridge: Add ability to enable TSO")
Suggested-by: Jiri Prochazka <jprochaz@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently following race is possible in team:
CPU0 CPU1
team_port_del
team_upper_dev_unlink
priv_flags &= ~IFF_TEAM_PORT
team_handle_frame
team_port_get_rcu
team_port_exists
priv_flags & IFF_TEAM_PORT == 0
return NULL (instead of port got
from rx_handler_data)
netdev_rx_handler_unregister
The thing is that the flag is removed before rx_handler is unregistered.
If team_handle_frame is called in between, team_port_exists returns 0
and team_port_get_rcu will return NULL.
So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister
that team_handle_frame will always see valid rx_handler_data pointer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ndo_bridge_setlink and ndo_bridge_dellink handlers point
to the default switchdev handlers
This follows my bonding driver changes.
I have only compile tested this patch. However similar
bonding code has been tested.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The deleted lines are called from a function which is called:
1) Only through __team_options_register via team_options_register and
2) Only during initialization / mode initialization when there are no
ports attached.
Therefore the ports list is guarenteed to be empty and this code will
never be executed.
Signed-off-by: Kenneth Williams <ken@williamsclan.us>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large receive offloading is known to cause problems if received packets
are passed to other host. Therefore the kernel disables it by calling
dev_disable_lro() whenever a network device is enslaved in a bridge or
forwarding is enabled for it (or globally). For virtual devices we need
to disable LRO on the underlying physical device (which is actually
receiving the packets).
Current dev_disable_lro() code handles this propagation for a vlan
(including 802.1ad nested vlan), macvlan or a vlan on top of a macvlan.
It doesn't handle other stacked devices and their combinations, in
particular propagation from a bond to its slaves which often causes
problems in virtualization setups.
As we now have generic data structures describing the upper-lower device
relationship, dev_disable_lro() can be generalized to disable LRO also
for all lower devices (if any) once it is disabled for the device
itself.
For bonding and teaming devices, it is necessary to disable LRO not only
on current slaves at the moment when dev_disable_lro() is called but
also on any slave (port) added later.
v2: use lower device links for all devices (including vlan and macvlan)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
When team_notify_peers and team_mcast_rejoin are called, they both reset
their respective .count_pending atomic variable. Then when the actual
worker function is executed, the variable is atomically decremented.
This pattern introduces a potential race condition where the
.count_pending rolls over and the worker function keeps rescheduling
until .count_pending decrements to zero again:
THREAD 1 THREAD 2
======== ========
team_notify_peers(teamX)
atomic_set count_pending = 1
schedule_delayed_work
team_notify_peers(teamX)
atomic_set count_pending = 1
team_notify_peers_work
atomic_dec_and_test
count_pending = 0
(return)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test
count_pending = -1
schedule_delayed_work
(repeat until count_pending = 0)
Instead of assigning a new value to .count_pending, use atomic_add to
tack-on the additional desired worker function invocations.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: David S. Miller <davem@davemloft.net>
When one tries to add eth as a port into team and that eth is already in
use by other rx_handler device (macvlan, bond, bridge, ...) a bug in
team_port_add() causes that IFF_TEAM_PORT flag is set before rx_handler
is registered. In between, netdev nofifier is called and
team_device_event() sees IFF_TEAM_PORT and thinks that rx_handler_data
pointer is set to team_port. But it isn't.
Fix this by reordering rx_handler register and IFF_TEAM_PORT priv flag
set so it is very similar to how bonding does this.
Reported-by: Erik Hugne <erik.hugne@ericsson.com>
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable "err" is not necessary.
Return register_netdevice() directly.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34c5bd66e5 introduced the possibility that an
uninitialized pointer on the stack (orig_fp) can call into
sk_unattached_filter_destroy() when its value is non NULL.
Before that commit orig_fp was only destroyed in the same
block where it was assigned a valid BPF prog before. Fix it
up by initializing it to NULL.
Fixes: 34c5bd66e5 ("net: filter: don't release unattached filter through call_rcu()")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pablo Neira <pablo@netfilter.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.
This is a short summary of clients of this function:
1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
are removed from the packet path before the filter is released. Thus,
the framework makes sure the filter is safely removed.
2) In the ppp driver, the ppp_lock ensures serialization between the
xmit and filter attachment/detachment path. This doesn't use rcu
so deferred release via rcu makes no sense.
3) In the isdn/ppp driver, it is called from isdn_ppp_release()
the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
Thus, deferred rcu makes no sense to me either, the deferred releases
may be just masking the effects of wrong locking strategy, which
should be fixed in the driver itself.
4) In the team driver, this is the only place where the rcu
synchronization with unattached filter is used. Therefore, this
patch introduces synchronize_rcu() which is called from the
genetlink path to make sure the filter doesn't go away while packets
are still walking over it. I think we can revisit this once struct
bpf_prog (that only wraps specific bpf code bits) is in place, then
add some specific struct rcu_head in the scope of the team driver if
Jiri thinks this is needed.
Deferred rcu release for unattached filters was originally introduced
in 302d663 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it is not possible to set mtu to team device which has a port
enslaved to it. The reason is that when team_change_mtu() calls
dev_set_mtu() for port device, notificator for NETDEV_PRECHANGEMTU
event is called and team_device_event() returns NOTIFY_BAD forbidding
the change. So fix this by returning NOTIFY_DONE here in case team is
changing mtu in team_change_mtu().
Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_fprog and sock_fprog_kern are of equal size, however
it's cleaner to just use sizeof(*fprog) instead to always
have correct type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_unattached_filter_create() API is used by BPF filters that
are not directly attached or related to sockets, and are used in
team, ptp, xt_bpf, cls_bpf, etc. As such all users do their own
internal managment of obtaining filter blocks and thus already
have them in kernel memory and set up before calling into
sk_unattached_filter_create(). As a result, due to __user annotation
in sock_fprog, sparse triggers false positives (incorrect type in
assignment [different address space]) when filters are set up before
passing them to sk_unattached_filter_create(). Therefore, let
sk_unattached_filter_create() API use sock_fprog_kern to overcome
this issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__team_compute_features() uses netdev_increment_features() to
combine vlan_features of slaves into vlan_features of the team.
As netdev_increment_features() only adds most features and we
start with TEAM_VLAN_FEATURES, we can end up with features none
of the slaves provided.
Initialize vlan_features only with the flags which are both in
TEAM_VLAN_FEATURES and NETIF_F_ALL_FOR_ALL. Right now there is
no such feature so that we actually initialize vlan_features
with zero but stating it explicitely will make the code more
future proof.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two breaks missing there. The result is that userspace
receives multiple messages which might be confusing.
Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like bonding, team as netdevice doesn't cross netns boundaries.
Team ports and team itself live in same netns.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju