override set_frontend to allow rf input path switching on the HVR1275
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes adds IR Rx keypress input event handling to the CX23885 module.
This change specifically only adds input handling for IR devices implemented as
v4l2_subdevices, using only the pulse width mode (for now), and only with
RC-5 remotes. The V4L-DVB infrastructure is missing too much to support RC-6
mode 6A as used in many media center remotes. The grey Hauppauge RC-5 remote
and HVR-1850 IR receiver work now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add integrated IR subdevice interrupt and notification handling. This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change completes the v4l2_subdev implementation for IR receive for the
IR controller built into the CX23888.
This changes almost completes the IR transmit side also, but doesn't. Instead
notes in the comments describe what needs to be done for IR Tx to work in the
subdevice implementation.
The current Tx behavior is skeletal and benign. If left alone, it does nothing.
It will only ever generate a Tx interrupt on Tx init by a caller or when the
tx_write() method is called. The ISR, when called, will then disable the Tx
FIFO service interrupt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prior mechanism wasn't reliable with the cx23887. This new mechanism
tests correctly against cx23885, 7 and 8 based products.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the IR controller on the CX23888 to work for the HVR-1850 and in
general, the A/V core must be initialized to get the VID_CLK going.
The VID_CLK is the timing reference for the CX23888's integrated
IR controller.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SYS and AUX PLLs need to be initialized to different values based on
the chip: CX23885, CX23887, CX23888, as each uses a different crystal
frequency: 28.6363 MHz, 25.0 MHz, 50.0 MHz.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate out the set_audclk_freq() function into separate functions for the
four families of cores. These cores all use slightly different sample clock
schemes and may be assuming slightly (+/- 3 Hz) different reference frequencies.
The code resuse was not worth the maintenance and testing headache of have all
chips use the same function peppered with conditional logic.
Added comments on how PLL and SRC parameters values are computed. Fixed a few
bugs related to the shared code having a large number of conditional statements.
Noted inconsistencies with FIXME in the comments.
This is done in preparation for getting the CX2388[578] PLL/clock setting logic
cleaned up for CX23888 analog video and IR (which need the VID PLL set right).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change logic to check for various chip or core families to inline functions.
Checks for specific chips should be made against the state->id field now. This
is in preparation for chip/core specific code for setting up PLLs for the
CX2388[578] family of cores, that all run with different crystal frequencies.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add improved logic to detect the exact CX2388[578] A/V core that is being
probed. Also cleaned up detection and logging for CX2310[12], CX2583[67],
and CX2584[0123] cores and chips.
Also added code to identify a CX2388[578] A/V decoder core that is not
responding properly. Typical symptoms include registers 0x00-0xff
responding properly but all other registers returning the same value
(0x13 and 0x5 have been observed). This state will cause proper detection of
'885 vs. '887 vs. '888 to fail and the chip won't respond to get configured
properly anyway. I have no method of reseting the core to a working state at
this time; but I didn't try too hard to work one out either. The problem
likely only occurs in development. I suspect configuring the SYS PLL VCO to
oscillate too slowly (286.3 MHz?) before post divide may be the root cause,
when encountered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller. This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.
The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes corrects the ioctl() operations for both the CX2388[578] analog
video and MPEG video device nodes to properly and consistently support
VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s.
This caused some ioctl() support routines to be broken out into a separate
source file.
Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers
including the CX2388[57] functions handled by the cx25840 module.
This was done in anticipation of developing a new v4l2_subdev for the
integrated IR controller of the CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri's patch for the Behold X7 didn't use the #define I had setup for
XC5000_RADIO_FM1, so cut over to using that instead of "1".
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the digital side of the Behold X7
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).
Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros. Between
the two of them, they got all the core functionality working for the device.
Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: Uroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems that the reference design used for the KWorld 2800d switched from the
em2860 to em2862, so we need to add the new USB id (and the i2c hash remains
so all we need is the default em2862 id.
Thanks to Ian Young for reporting the issue and testing the fix.
Cc: Ian Young <ian@duffrecords.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Trivial fix for this compile warning:
v4l/sh_mobile_ceu_camera.c:1789: warning: label 'exit_free_irq' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vpif_config struct was renamed to vpif_display_config, but there
is still a stray vpif_config *config pointer in vpif_display.c, preventing
it from compiling.
Remove this old duplicate pointer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set device GPIOs only once. There is no need for .dvb_gpio to select
between analog and digital because device is digital only.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit ef373189f62413803b7b816c972fc154c488cdc0 "fix use-after-free Oops,
resulting from a driver-core API change" fixed the Oops, but didn't correct
missing device object initialisation. This patch makes unloading and reloading
of soc-camera host- and client-drivers possible again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of the following drivers in media video:
drivers/media/video/ivtv/ivtv-driver.c
drivers/media/video/cx18/cx18-driver.c
drivers/media/video/davinci/dm355_ccdc.c
drivers/media/video/davinci/dm644x_ccdc.c
drivers/media/video/saa7164/saa7164-core.c
drivers/media/video/saa7134/saa7134-core.c
drivers/media/video/cx23885/cx23885-core.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Andy Walls <awalls@radix.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Acked-By: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch was generated by
git grep -E -i -l 's(le|el)ct' | xargs -r perl -p -i -e 's/([Ss])(le|el)ct/$1elect/
with only skipping net/netfilter/xt_SECMARK.c and
include/linux/netfilter/xt_SECMARK.h which have a struct member called
selctx.
Signed-off-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Hauppauge WinTV HVR-1150 retail boards require the FORCE_TS_VALID bit
to be set in order to function properly. This change will work on the early
revisions on the board as well, but the final revision will not function
without this change.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When FORCE_TS_VALID mode is enabled, the saa713x will accept MPEG TS input
without requiring TS_VALID set high. This is required for some new boards
to function properly, due to the hardware design implementation.
The configuration is toggled within the board setup configuration. Boards
that do not have this bit set will function as before with no change.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The abs() macro has changed in 2.6.32 and returns a long instead of an
int. Fix the driver to avoid compilation warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FIX_BANDWIDTH quirk tries to work around cameras requesting the
maximum bandwidth regardless of the image size by computing a bandwidth
estimate. This works only for uncompressed frames.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Cc: Antti Palosaari <crope@iki.fi>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Change vstart for CIF sensor type 1 cams
This fixes the distortion at the end of the frame, and avoids the bad frame
dropping done because of this distortion, trippling the framerate!
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a vflip quirk for the Fujitsu Amilo Xi 2528. Thanks to Evgeny for the report.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds another vflip quirk for the MSI GX700.
Thanks to John Katzmaier for reporting.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a vflip quirk for the Bruneinit laptop. Thanks to Jörg for the report
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s2255 driver had logic which aborted processing of a video frame
if there was no process waiting on the video buffer in question. That
simply doesn't work when the application is doing things in an
asynchronous manner. If the application went to the trouble to queue
the buffer in the first place, then the driver should always attempt
to complete it - even if the application at that moment has its
attention turned elsewhere. Applications which always blocked waiting
for I/O on the capture device would not have been affected by this.
Applications which *mostly* blocked waiting for I/O on the capture
device probably only would have been somewhat affected (frame lossage,
at a rate which goes up as the application blocks less). Applications
which never blocked on the capture device (e.g. polling only) however
would never have been able to receive any video frames, since in that
case this "is anyone waiting on this?" check on the buffer never would
have evalutated true. This patch just deletes that harmful check
against the buffer's wait queue.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: stable@kernel.org
Because the counters were not reset when starting up streaming, they would
be reused from the previous run. This can result in cases such that when the
second instance of streaming starts up, the "cnt" variable in
em28xx_audio_isocirq() can end up being negative, resulting in attempting to
write to memory before the start of runtime->dma_area (as well as having a
negative number of bytes to copy).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bttv driver function which handles switching of the video standard
(set_tvnorm() in bttv-driver.c) includes a check which can optionally
also reset the cropping configuration to a default value. It is
"optional" based on a comparison of the cropcap parameters of the
previous vs the newly requested video standard. The comparison is
being done with a memcmp(), a function which only returns a true value
if the comparison actually fails.
This if-statement appears to have been written to assume wrong
memcmp() semantics. That is, it was re-initializing the cropping
configuration only if the new video standard did NOT have different
cropcap values. That doesn't make any sense. One definitely should
reset things if the cropcap parameters are different - if there's any
comparison to made at all.
The effect of this problem was that a transition from, say, PAL to
NTSC would leave in place old cropping setup that made sense for the
PAL geometry but not for NTSC. If the application doesn't care about
cropping it also won't try to reset the cropping configuration,
resulting in an improperly cropped video frame. In the case I was
testing this actually caused black video frames to be displayed.
Another interesting effect of this bug is that if one does something
which does NOT change the video standard and this function is run,
then the cropping setup gets reset anyway - again because of the
backwards comparison. It turns out that just running anything which
merely opens and closes the video device node (e.g. v4l-info) will
cause this to happen. One can argue that simply opening the device
node and not doing anything to it should not mess with any of its
state - but because of this behavior, any TV app which does such
things (e.g. xawtv) probably therefore doesn't see the problem.
The solution is to fix the sense of the if-statement. It's easy to
see how this mistake could have been made given how memcmp() works.
The patch is therefore removal of a single "!" character from the
if-statement in set_tvnorm in bttv-driver.c.
Signed-off-by: Mike Isely <isely@pobox.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a subtle interaction in the bttv driver which can result in
fields being repeatedly processed out of order. This is a problem
specifically when running in V4L2_FIELD_ALTERNATE mode (probably the
most common case).
1. The determination of which fields are associated with which buffers
happens in videobuf, before the bttv driver gets a chance to queue the
corresponding DMA. Thus by the point when the DMA is queued for a
given buffer, the algorithm has to do the queuing based on the
buffer's already assigned field type - not based on which field is
"next" in the video stream.
2. The driver normally tries to queue both the top and bottom fields
at the same time (see bttv_irq_next_video()). It tries to sort out
top vs bottom by looking at the field type for the next 2 available
buffers and assigning them appropriately.
3. However the bttv driver *always* actually processes the top field
first. There's even an interrupt set aside for specifically
recognizing when the top field has been processed so that it can be
marked done even while the bottom field is still being DMAed.
Given all of the above, if one gets into a situation where
bttv_irq_next_video() gets entered when the first available buffer has
been pre-associated as a bottom field, then the function is going to
process the buffers out of order. That first available buffer will be
put into the bottom field slot and the buffer after that will be put
into the top field slot. Problem is, since the top field is always
processed first by the driver, then that second buffer (the one after
the first available buffer) will be the first one to be finished.
Because of the strict fifo handling of all video buffers, then that
top field won't be seen by the app until after the bottom field is
also processed. Worse still, the app will get back the
chronologically later bottom field first, *before* the top field is
received. The buffer's timestamps will even be backwards.
While not fatal to most TV apps, this behavior can subtlely degrade
userspace deinterlacing (probably will cause jitter). That's probably
why it has gone unnoticed. But it will also cause serious problems if
the app in question discards all but the latest received buffer (a
latency minimizing tactic) - causing one field to only ever be
displayed since the other is now always late. Unfortunately once you
get into this state, you're stuck this way - because having consumed
two buffers, now the next time around the "first" available buffer
will again be a bottom field and the same thing happens.
How can we get into this state? In a perfect world, where there's
always a few free buffers queued to the driver, it should be
impossible. However if something disrupts streaming, e.g. if the
userspace app can't queue free buffers fast enough for a moment due
perhaps to a CPU scheduling glitch, then the driver can get
momentarily starved and some number of fields will be dropped. That's
OK. But if an odd number of fields get dropped, then that "first"
available buffer might be the bottom field and now we're stuck...
This patch fixes that problem by deliberately only setting up a single
field for one frame if we don't get a top field as the first available
buffer. By purposely skipping the other field, then we only handle a
single buffer thus bringing things back into proper sync (i.e. top
field first) for the next frame. To do this we just drop the few
lines in bttv_irq_next_video() that attempt to set up the second
buffer when that second buffer isn't for the bottom field.
This is definitely a problem in when in V4L2_FIELD_ALTERNATE mode. In
the other modes this change either has no effect or doesn't harm
things any further anyway.
Signed-off-by: Mike Isely <isely@pobox.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b402843787 has broken again re-use of
device objects across device_register() / device_unregister() cycles. Fix
soc-camera by nullifying the struct after device_unregister().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in cropping calculation, when the client is also scaling the image.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When we call gspca_frame_add, it returns a pointer to the frame passed in,
unless we call it with LAST_PACKET, when it will return a pointer to a
new frame in which to store the frame data for the next frame.
The frame pointer was not updated in stv06xx and ov518.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (13039): dib0700: not building CONFIG_DVB_TUNER_DIB0070 breaks compilation
V4L/DVB (13038): dvbdev: Remove an anoying/uneeded warning
V4L/DVB (13037): go7007: Revert compatibility code added at the wrong place
media: video: Fix build in saa7164
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-tip testing found that the x86 build (64-bit allyesconfig) fails due to:
LD vmlinux.o
drivers/built-in.o:(.bss+0x4b648): multiple definition of `debug'
arch/x86/built-in.o:(.kprobes.text+0x88): first defined here
ld: Warning: size of symbol `debug' changed from 90 in
arch/x86/built-in.o to 4 in drivers/built-in.o
make: *** [vmlinux.o] Error 1
This is because recent saa7164 changes introduced a global symbol
named 'debug'. The x86 platform code already defines a 'debug'
symbol. (which is named in a too generic way as well - but it
can be used nicely to weed out too generic symbols in drivers ;-)
Rename it to saa_debug.
[mchehab@redhat.com: use module_param_named to preserve old name]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
The build of the dabusb driver broke:
drivers/media/video/dabusb.c:758: error: unknown field 'nodename' specified in initializer
drivers/media/video/dabusb.c:758: warning: initialization from incompatible pointer type
make[3]: *** wait: No child processes. Stop.
Due to this commit:
e454cea: Driver-Core: extend devnode callbacks to provide permissions
Missing the dabusb driver's dabusb_nodename() callback.
Similar issues with the iio/industrialio driver in staging, pointed out
and patched by Jean Delvare.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Industrialio-parts-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to several files in drivers/media/video/cx88/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is an initial driver for Analog Devices ADV7180 Video Decoder.
So far it only supports query standard.
[akpm@linux-foundation.org: remove unneeded cast]
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the kzalloc and associated test after the stream/query test, to avoid
the need to free the allocated if the stream/query test fails.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to rounding and clipping, exposure and gain settings do not map to
unique register values. Rather than read the registers and report gain
and exposure that may be different than the values that were set, just
cache the latest values that were set and report them. Reduce exposure
range from 0-65535 to 0-255 so libv4l's autogain doesn't take forever.
Remove vestiges of driver signal processing that is now handled by
libv4l.
Signed-off-by: James Blanford <jhblanford@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize image size before it's used to initialize exposure.
Work around lack of exposure set hardware latch with a sequence of
register writes in a single I2C command packet.
Signed-off-by: James Blanford <jhblanford@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
http://linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
test status analog (PAL-B):
- Sometimes picture is noisy, but it becomes crystal clear after
switching between channels. (happens for example at 687.25 Mhz)
- On a lower frequency (511.25 Mhz) the picture is always sharp, but
lacks colour.
- No sound problems.
- radio untested.
Digital:
- DVB-T/H stream reception works.
- Would expect to see some more channels in the higher frequency region.
Overall is the impression that sensitivity still needs improvement
both in analog and digital modes.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When fast push-pull button of remote control we can received incorrect
key code 0x00. Key information from IR decoder has ID of remote control 2 bytes,
byte of key code and byte of mirror key code.
Correct data
0x86 0x6B 0x00 0xFF
Wrong data
0x86 0x6B 0x00 0x00
This patch added additional test of mirror byte for filtering.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/gspca/gl860/gl860.c: In function ‘gl860_build_control_table’:
drivers/media/video/gspca/gl860/gl860.c:119: warning: ‘sd_ctrls’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/saa7164/saa7164-buffer.c: In function ‘saa7164_buffer_alloc’:
drivers/media/video/saa7164/saa7164-buffer.c:110: warning: cast to pointer from integer of different size
drivers/media/video/saa7164/saa7164-buffer.c:112: warning: cast to pointer from integer of different size
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Following changes done for vpif driver to support vpif capture:-
1) Current version of display driver defined vpif register
space as part for vpif display platform driver resource
This is not correct since vpif is common across capture
and display drivers. So the resource iomap function is
moved to this module
2) Since there are common registers, a spinlock is added for
mutual exclusion.
This has incorporated comments against version v0 of the patch series
Resending to merge to V4L linux-next
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the vpif capture bridge driver for DM6467. This video
supports two video channels each having a tvp5147 device at
the input. This allows simultaneous capture of NTSC/PAL video
in each of this channel. Both MMAP and USERPTR io mechanism
are supported. Currently buffer allocation happens at REQBUF
ioctl request. Since USERPTR IO is supported, this is not an
issue since user applications can allocate buffers and pass
the user space address to the driver. Following are TODOs :-
1) Adding support for allocation of buffers at init
2) VBI/HBI data service
This has incorporated comments received against version v0
of the patch series.
Resending to merge V4l linux-next
create mode 100644 drivers/media/video/davinci/vpif_capture.c
create mode 100644 drivers/media/video/davinci/vpif_capture.h
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The structure name for vpif display driver changed since it was not unique. So this
update is done to reflect the same. Also removed the code related to register
address space iomap. Uses v4l2_i2c_new_subdev_board() instead of
v4l2_i2c_new_probed_subdev() so that platform data can be added for subdevice
configuration for polarities.
This has incorporated comments against version v0 of the patch series.
Resending the original patch for merge to V4L linux-next
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warn when the desired device node number is already in use, except when
the new video_register_device_no_warn function is called since in some
use-cases that warning is not relevant.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some subtle differences in the way the devnode numbers are
handled depending on whether the FIXED_MINOR_RANGES config option is
set. Add some simple wrapper functions to handle that correctly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The term 'kernel number' is very vague, so replace it with the somewhat more
descriptive term 'device node number'.
In one place the local variable 'nr' was used to create the device node number
of the new device name. This has been replaced with the vdev->num field to
more clearly mark this as being the device node number and not the minor
number.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_register_device_index is never actually called, instead the
stream index number is always calculated automatically.
This patch removes this function and simplifies the internal get_index
function since that can now always just return the first free index.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite v4l2_i2c_new_subdev as a simplified version of v4l2_i2c_new_subdev_cfg
and remove v4l2_i2c_new_probed_subdev and v4l2_i2c_new_probed_subdev_addr.
This simplifies this API substantially.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we are not using v4l2_device_call_* calls any more, we don't need to
initialise subdevice .grp_id any more. This also fixes compiler warnings on
64-bit platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the soc-camera interface for V4L2 subdevices thinner yet. Handle
gain and exposure internally in each driver just like all other controls.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unneeded soc-camera operations, this also makes the soc-camera API to
v4l2 subdevices thinner.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial soc-camera scaling and cropping implementation turned out to be
incompliant with the V4L2 API, e.g., it expected the user to specify cropping
in output window pixels, instead of input window pixels. This patch converts
the soc-camera core and all drivers to comply with the standard.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_subdev_call() instead of v4l2_device_call_until_err() in all host
drivers and in soc-camera core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove set_crop soc-camera device method and switch to s_crop from v4l2-subdev
video operations. Also extend non-i2c drivers to also hold a pointer to their
v4l2-subdev instance in control device driver-data, i.e., in
dev_get_drvdata((struct device *)to_soc_camera_control(icd))
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use host-side image scaling when the client fails to set the requested format.
We also have to take scaling into account when performing host-side cropping.
Similar to cropping we try to use client-side scaling as much as possible to
preserve bus bandwidth and optimise the frame-rate.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current tw9910 driver does not implement cropping correctly. Therefore, and
also because various rectangles in struct soc_camera_device are in user scale,
we cannot and shall not use rect_current as window location.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OV772x sensors cannot crop, they only support two fixed formats: VGA and QVGA.
We should not change the format when requested to crop, only S_FMT can do this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prohibit S_FMT and S_CROP with a different window width or height after video
buffer initialisation. This simplifies the work to be done in specific host and
client drivers, and it doesn't seem to make much sense to allow these changes.
We do however allow S_CROP with equal width and height to just move the window,
this doesn't affect video buffer management and is usually easy enough to
implement.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API mandates, that drivers do not update the argument of the S_CROP
ioctl() with the actual geometry. Comply.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all video capture devices can configure arbitrary cropping, whereas the
CEU module on SuperH CPUs can crop with pixel precision. However, we want to
use camera cropping if possible to save bandwidth and increase the frame-rate.
This patch verifies whether the camera managed to crop exactly the requested
rectangle, and if not, uses host-side cropping. To be able to crop on CEU we
have to preserve camera rectangle too, for which the host_priv member in
struct soc_camera_device is used. We now allocate memory dynamically, thus we
have to use the .put_formats() method from struct soc_camera_host_ops to free
it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch
[PATCH] video: use videobuf_waiton() in sh_mobile_ceu free_buffer()
was not quite correct. It closed a race, but introduced a potential
lock-up, if for some reason an interrupt does not come. This has been
observed in tests with tw9910. This patch safely dequeues buffers without
waiting for their completion. It also moves a buffer state assignment
under a spinlock to make it atomic with queuing of the buffer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The move of format translation initialisation into soc_camera_open() was
temporary for the soc-camera as platform driver intermediate step, put it back
into soc_camera_probe(). Also add a .put_formats() method to
soc_camera_host_ops to free any resources host driver might have allocated in
.get_formats().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 drivers are allowed to configure a geometry different than what has been
requested by the user with S_CROP, but then they have to adjust the input
rectangle accordingly. Fix ov772x to comply with this requirement.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. soc-camera always requests a valid rectangle, when calling .s_fmt(), no need
to check and adjust
2. in .s_crop(), if the rectangle exceeds sensor limits, push it to the
respective border instead of centering
3. take into account left and top borders when checking
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to using struct v4l2_rect in struct soc_camera_device for uniformity and
simplicity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the V4L2_CID_SHARPNESS control to switch SH-mobile camera low-pass filter.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now soc-camera only supported client (sensor) controls. This patch
enables camera-host drivers to implement their own controls too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_BAND_STOP_FILTER control is used to switch the "Banding Filter" on
OV772x cameras on and off and to set the minimum AEC value in BDBASE register.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the soc-camera framework to use the v4l2-(sub)dev API. Start using
v4l2-subdev operations. Only a part of the interface between the
soc_camera core, soc_camera host drivers on one side and soc_camera device
drivers on the other side is replaced so far. The rest of the interface
will be replaced in incremental steps, and will require extensions and,
possibly, modifications to the v4l2-subdev code.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all drivers to platform device API. We already
converted platforms to register a platform device for each soc-camera client,
now we remove the compatibility code and switch completely to the new scheme.
This is a preparatory step for the v4l2-subdev conversion.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_platform.c is only used by y SuperH ap325rxa board. This patch
converts soc_camera_platform.c and its users for the soc-camera platform-
device conversion and also extends soc-camera core to handle non-I2C cameras.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the platform header file, the subdev_info structure name has been changed
to vpif_subdev_info. Update this change in the driver too.
Applies to v4l-dvb repository.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new module added for vpss library functions that are
used for configuring vpss system module. All video drivers will
include vpss.h header file and call functions defined in this
module to configure vpss system module.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the hw module for DM644x CCDC. This registers with the
vpfe capture driver and provides a set of hw_ops to configure
CCDC for a specific decoder device connected to the VPFE.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds ccdc hw module for DM355 CCDC. This registers with the bridge
driver a set of hw_ops for configuring the CCDC for a specific
decoder device connected to vpfe.
Reviewed by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This the vpfe capture bridge driver for doing video
capture on DM355 and DM6446 evms. The ccdc hw modules register with the
driver and are used for configuring the CCD Controller for a specific
decoder interface. The driver also registers the sub devices required
for a specific evm. More than one sub devices can be registered.
This allows driver to switch dynamically to capture video from
any sub device that is registered. Currently only one sub device
(tvp5146) is supported. But in future this driver is expected
to do capture from sensor devices such as Micron's MT9T001, MT9T031
and MT9P031 etc. The driver currently supports MMAP based IO.
Reviewed by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mutex_lock_interruptible return value has to be handled properly to indicate
the status to the higher layers of the kernel.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makefile and Kconfig changes for DM646x Video Display device, using
davinci/vpif, adv7343 and ths7303 drivers.
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code be used by the display and capture drivers.
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Red and blue gain isn't handled in conformance with the v4l2 specification. Disable them for now.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't set blue and red gain during init as we manuall set it later
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We manually set the gain later, no need to do it during init
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that the default exposure value is set at startup
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7164: Remove the SAA7164 bus id, no longer required.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following build warning:
CC [M] saa7164-core.o
saa7164-core.c: In function 'saa7164_buffer_deliver':
saa7164-core.c:113: warning: passing argument 2 of 'dvb_dmx_swfilter_packets'
from incompatible pointer type
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for NXP TDA18271 as a standalone tuner, allowing the use of
analog demodulators other than the Philips/NXP TDA829x.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card uses the same cx23885 gpio lines for two adapters.
In case of there is several cards in system we must implement
gpio mutex per cx23885 chip.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for Reddo DVB-C USB TV Box device. Remote is not working yet.
Thanks to Benjamin Larsson <banan@ludd.ltu.se>
Cc: Benjamin Larsson <banan@ludd.ltu.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_G_STD ioctl may not be present in the case of radio receivers.
In that case G_STD will return an error. The v4l1-compat layer should not
attempt to propagate that error to the caller, instead it should be
ignored.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7164: Add support for a new HVR-2250 hardware revision
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7164: Ensure the HVR-2200 second tuner is configured in slave mode.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that by default all tuners are set correctly to master/slave mode.
For all HVR2250's, ensure slave based tuners are caliberated during attach
to avoid locking problems on tuner# above channel 91.
HVR2200 tuner attach time to be reviewed in a future patch.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases we're seeing large timeouts on commands. I'm changing the
implementation so that the deferred worker checks the PCI bus for
any messages and signals the waiting caller accordingly. The previous
mechanism was too unreliable.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firmware typically responds in < 50ms and, via the interrupts and
deferred work queue the caller (blocked in the driver) is signalled very
efficiently. In a highly stressed system this can take many multiples
of seconds. So, we need a larger maximum timeout for busy systems.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup a printk and output two helpful driver params in debug mode.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's timing out and aborting firmware load too quickly on some
platforms, this increases the upper limit.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for all of the known shipping Hauppauge HVR-2200
and HVR-2250 boards. Digital TV ATSC/QAM and DVB-T is enabled at this
time. Both tuners are supported.
Volatiles and typedefs need rework, the rest is coding style compliant.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c-kbd-i2c allows a bridge driver to pass information about IR configuration,
but uses a "void *" to pass along what is essentially constant data. This
change casts a const * to a void * to remove the warning.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some emacs tags from em28xx-vbi.c, which were copied from cx88-vbi.c,
per Mauro Carvalho Chehab's request.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some codingstyle issues introduced during the addition of em28xx VBI
support. The patch makes no functional changes other than converting a few
debug printk() statements to em28xx_isocdbg.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a few codingstyle issues introduced when I was adding the VBI support to
the em28xx driver.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MSI GX700 is a tricky machine to support. Some revisions do need the sensor flipped, but not all.
Add another quirk, distinguished by its BIOS date.
Signed-off-by: Brian Kloppenborg <bkloppenborg@gmail.com>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add vflip quirk for the Fujitsu Siemens Amilo Pa 2548
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unused variable from when I introduced the g_std() function.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove redundant call to set the vinctrl register. This eliminates any
ambiguity as to how the register is configured (since it is now always set in
em28xx_set_outfmt).
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to implement the g_std call, or else the default norm always gets
returned, which breaks VBI capturing if you had changed the standard to NTSC
using s_std.
I had temporarily changed the default norm to NTSC so that zvbi-ntsc-cc
wouldn't choke, so now that we are returning the correct value, switch it back
to PAL as the default.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the code so we only claim to support VBI if the underlying chipset
actually has the support.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not create the VBI device in cases where VBI is not supported on the target
em28xx chip.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current locking infrastructure didn't support having multiple fds accessing
the device (such as video and vbi). Rework the locking infrastructure,
borrowing the design from cx88.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When adding support for both video and VBI, I missed the mmap ioctl. Add
the missing call.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC. Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).
Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly). The default norm really should
be moved into a board-level parameter.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).
Note that this version just drops the actual VBI data onto the floor as
opposed to processing it. The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.
We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data. In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly document the video input control register, in preparation for the
addition of VBI support. Note this patch makes no functional changes.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added Kworld DVD Maker 2
Thanks to C Western <l@c-m-w.me.uk> for reporting this board.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some extra parenthesis at the clauses, and some switch() tests
for boards that don't have i2c ir. Remove those extra code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the logic to load ir i2c ancillary module is broken. It is
associated to Hauppauge devices with IR flag on their eeprom, no matter
if the device uses i2c or em28xx direct IR support. That's wrong.
Instead, add a flag to the boards that use i2c IR chips and load the
module only for those devices and if ir is not disabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.
Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.
Before this patch, if ir-kbd-i2c were probed after SAA7134, trash data
were used.
Compile tested only, but the patch is identical to em28xx one. So, it
should work properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at ir-kbd-i2c
module load), than the lifetime of a struct IR_i2c_init_data allocated off of
the stack in cx18_i2c_new_ir() at registration time. Make sure we pass
a pointer to a persistent IR_i2c_init_data object at i2c registration time.
Thanks to Brian Rogers for pointing out a solution, and Dustin Mitchell for
testing against a 2.6.30 kernel.
Reported-by: Dustin Mitchell <soxslayer@gmail.com>
Reported-by: Brian Rogers <brian@xyzw.org>
Tested-by: Dustin Mitchell <soxslayer@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.
Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.
Before this patch, if ir-kbd-i2c were probed after em28xx, trash data
were used. After the patch, no matter what order, it is properly
reported as tested by me:
input: i2c IR (i2c IR (EM2840 Hauppaug as /class/input/input10
ir-kbd-i2c: i2c IR (i2c IR (EM2840 Hauppaug detected at i2c-4/4-0030/ir0 [em28xx #0]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the MT9M111's IFP to handle exposure/gain gives better results.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use s16 instead of int where possible.
Use struct instead of arrays
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes broken exposure on SOI968 webcams that was causing
the camera to display a black screen
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let 0c45:60fc in sn9c102 and 0c45:613e in gspca-sonixj (sensor not supported).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new exchanges are taken from the information file of the ms-win driver
(usbvm326.inf - webcam 15b8:6002).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Add one more vivitar mini cam to the list of CIF cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Allow overriding of detected sensor type
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Use correct register for CIF type 1 sensor gain settings
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Add controls for CIF type 0 sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: make the probing a bit less chatty
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Move detection of CIF sensor type to probe() function,
so that the right controls are set to disabled from the start, rather then
having them disappear all of a sudden when the stream is started.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: cleanup/fixup control handling
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca: mr97310a fix detection of sensortype for vivicam with id byte of 0x53
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds supports for mr97310a camera's with CIF sensors (2 different
types) and for VGA mr97310a camera with a different sensor then supported
until now.
This patch also add support for controls for one of the 2 CIF sensors, this
was written by Thomas Kaiser <thomas@kaiser-linux.li>
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Thomas Kaiser <thomas@kaiser-linux.li>
Signed-off-by: Hans de Goede <hdgoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we've figured out the higher compression settings (supported in
libv4l-0.6.0 and later, so after this patch the driver should be used with
libv4l-0.6.0 or higher only!), we can enable higher framerates. Which
means lower exposure times, which is important for the use of the pac207
in full daylight.
This patch also tweakes the brightness default and the per color gain
balances to use the values which are adviced by Pixart in the pac207
application note.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_pac207: remove a number of unneeded (repeated) register writes
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the model there are three different firmwares to choose from.
Unfortunately if a cx23885 is loaded first, then the global firmware name
is overwritten with that firmware and if ivtv is loaded next, then it
tries to load the wrong firmware. In addition, the original approach would
also overwrite any firmware that the user specified explicitly.
Cc: Jarod Wilson <jarod@wilsonet.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- bad sensor power
- bad edge gain/threshold
- set back the auto gain
- light frequency filter inverted
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support for RoverMedia TV Link Pro FM (LR138 REV:I) card
based on saa7134.
Signed-off-by: Eugene Yudin <Eugene.Yudin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support our new TV card based on xc5000 and saa7134.
Analog TV works well.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch introduces new snd_saa7134_capsrc_set (code taken from
snd_saa7134_capsrc_put) that updates also the ALSA capture controls during
snd_card_saa7134_capture_prepare and snd_saa7134_capsrc_put.
There can be much more work done in order to unify the control of the card
(now the card's capture source is tuned/switched in saa7134-video.c too), but
I don't have enough time. This work could be a starting point, but it can be
applied as-is too (it doesn't need any further work to make it working).
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hello kernel developers.
I found a bug report from an user in launchpad. I just copy it here. It
includes patch.
I don't own the necessary hardware to test it but the patch looks
trivial.
I'm not subscribed to this list, so please CC me. Thanks!
Here is the text:
"""
remote control for my tv card doesnt work
I have Askey CPH03x TV Capturer.
When I load bttv module with "card=59" option which is proper for this
tv card,
I can watch tv with sound but my remote control doesnt work. There is no
ir
event in /proc/bus/input/device .
When bttv module is loaded with "card=137" option remote control works
very
well.
$ cat /proc/bus/input/devices
.......
........
: Bus=0001 Vendor=109e Product=0350 Version=0001
N: Name="bttv IR (card=137)"
P: Phys=pci-0000:00:0d.0/ir0
S: Sysfs=/devices/pci0000:00/0000:00:0d.0/input/input144
U: Uniq=
H: Handlers=kbd event6
B: EV=100003
B: KEY=2c0814 100004 0 0 0 4 2008000 2090 2001 1e0000 4400 0 ffc
Unfortunately there is no sound.
"""
https://bugs.launchpad.net/ubuntu/+bug/239733http://bugzilla.kernel.org/show_bug.cgi?id=11995
--
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support to AverMedia Studio 505
[dougsland@redhat.com: fixed rejects and removed the change to add dk as default secam variant]
[mchehab@redhat.com: fix a few CodingStyle issues]
Signed-off-by: Vasiliy Temnikov <vaka@newmail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds basic configurations for FM TX extended controls.
That includes controls names, menu strings, pointer identification,
type classification and flags configuration.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The upcoming RDS encoder needs support for string controls. This patch
implements the core implementation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the recent improvements we don't need to probe anymore, if we know
the i2c address of the receiver.
The address of the receiver for the remote with the gray buttons is not
confirmed anywhere, but it is very unlikely to see it on something else.
We want to have that information anyway.
BTW, those remaining still probing, please join.
Signed-off-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes an unneeded power management primitive.
Power management is automatically enabled as probe ends.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several reasons:
- SAA7133/35 uses DDEP (DemDec Easy Programming mode), which works in 32kHz
only
- SAA7134 for TV mode uses DemDec mode (32kHz)
- Radio works in 32kHz only
- When recording 48kHz from Line1/Line2, switching of capture source to TV
means switching to 32kHz without any frequency translation
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Acked-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I just happen to peek inside the PWC driver and did not like what I saw
there. Please consider applying the patch below.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It does matter to set explicitly gpio0 value in
cx88_board structure for TBS 8920 card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The changeset 0b17d0ed that aded ASUSTeK P7131 Analog were using
7 spaces instead of tab, probably due to some bad cut-and-paste.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On VIDEO_M52790 and USB_GSPCA_SN9C20X, instead of tab, it were
using 7 whitespaces at the beginning, probably due to some
cut-and-paste trouble.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch solves problem of missed keystrokes on some remote controls,
as reported on http://bugzilla.kernel.org/show_bug.cgi?id=9637 .
Signed-off-by: Andrzej Hajda <andrzej.hajda@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I updated and simplyfied patch from Zbynek Hrabovsky for recent kernel.
It enables autodetection of card, sound in analog TV , sound in FM radio
and switching between antenna and cable RF input. Radio tuner still
doesn't work, I don't even know how it works. Some guys wrote me that FM
radio works with TV tuner used instead of radio part (symlink video0 ->
radio0).
Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Vlastimil Labsky <vlasta.labsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error handling code following a kmalloc should free the allocated data.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have support for radio on saa7133/35/31e cards with tda8290/8275(a)
and 5.5MHz ceramic filter on the bridge chips since a while.
It was previously not tested, if this card supports it too, but the old
"ghost" radio with wrong filters doesn't work anymore.
Thanks go to Pham Thanh Nam and Laszlo Kustan for reporting it working
on that input.
Signed-off-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Define correct tuner in config. Radio now works fine
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restructure the UVC descriptors parsing code to handle multiple streaming
interfaces. The driver now creates a uvc_video_chain instance for each chain
detected in the UVC control interface descriptors, and tries to register one
video device per streaming endpoint.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards multiple streaming interfaces support, reorganize the
driver's data structures to cleanly separate video control and video streaming
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 API (chapter 1.5) states that:
Drivers must implement all input ioctls when the device has one
or more inputs, all output ioctls when the device has one or more outputs.
When the device has any audio inputs or outputs the driver must set the
V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
VIDIOC_QUERYCAP ioctl.
So, devices without audio input should return -EINVAL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are many lock imbalances in this driver. Fix all found.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There seems to be one superfluos unlock in a poll function. Remove it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The irq handler will touch memory. Even in the error case some URBs may
complete. Thus no memory must be kfreed before all URBs are killed.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Zilog Z8F0811 IR transceiver chips on
CX2341[68] based boards to ir-kbd-i2c for both the old i2c binding model
and the new i2c binding model.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support to the cx18 driver for setting up the
Z8F0811/Hauppauge IR Tx/Rx chip with the i2c binding model in newer
kernels.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functions which are referenced by their address can't be inlined by
definition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au0828-dvb driver uses bulk usb transfers for digital transport,
but the debug reports, "iso xfer already running!\n".
Fix this to report bulk instead of isoc.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents a loop if a permanent error occurs in usb_set_interface().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patches
gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.
gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.
will make the preview function not work, so I disable the 1280x1024 resolution
and revert back to the origin mi1310_soc settings.
And, using USB snoop tool on Windows to get the correct i2c commands to
turn on/off the LED flash.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* use i2c_w instead of reg_w
* return error on failure
* read the correct number of bytes
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the i2c subdev changes the ordering of initialization changed,
causing a total loss of previous GPIO settings and a loss of DTV.
The generic firmware loading routine has now changed to preserve
GPIO values if the device is cx23885 based (safety) and I've
moved the GPIO configuration from probe() into the cx23885 init
func which is a little clearer and fixes the bug.
Tested-by: Sohail Syyed <linuxtv@hubstar.net>
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.
Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the subdev_s_std() method from the GPIO subdev. It appears it was
used in the past to effect the switch back from radio mode to tuner mode,
but it had a side effect that is improper and against the V4L2 spec, when
you were not in radio mode. Whenever the video stanadrd was changed, the
GPIO audio mux was set back to the tuner audio input, even if you were set
to a Line In input.
Thanks to Ravi A. for doing the troubleshooting to point me right to the
problem.
Reported-by: Ravi A <asvravi@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Marton Nemeth