Commit Graph

3564 Commits

Author SHA1 Message Date
Martin Blumenstingl bf6f146f32 pinctrl: meson: meson8: add the RGMII RXD2/RXD3 and TXD2/TXD3 signals
These are only available on the Meson8m2 SoC (which uses the same
DesignWare Ethernet MAC as Meson8b).
The "eth_tx_clk_50m" signal either provides a 50MHz clock for the RMII
PHYs or the RGMII TX clock (as far as we know the frequency is
controlled by the PRG_ETHERNET registers in the Ethernet MAC "glue" IP
block).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:08 +02:00
Martin Blumenstingl b0d46cb598 pinctrl: meson: meson8: add support for the Meson8m2 SoC
Add Meson8m2 support to the existing Meson8 pinctrl driver. Since there
are only very few changes (Meson8m2 has an extra signal on 10 CBUS pins,
no other differences were found so far).
Add the new compatible strings for Meson8m2 to the existing Meson8
driver so we don't have to duplicate the whole driver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:08 +02:00
Timur Tabi e508099084 pinctrl: qcom: qdf2xxx: add support for new ACPI HID QCOM8002
Newer versions of the firmware for the Qualcomm Datacenter Technologies
QDF2400 restricts access to a subset of the GPIOs on the TLMM.  To
prevent older kernels from accidentally accessing the restricted GPIOs,
we change the ACPI HID for the TLMM block from QCOM8001 to QCOM8002,
and introduce a new property "gpios".  This property is an array of
specific GPIOs that are accessible.  When an older kernel boots on
newer (restricted) firmware, it will fail to probe.

To implement the sparse GPIO map, we register all of the GPIOs, but
fill in the data only for available GPIOs.  This ensures that the driver
cannot accidentally access an unavailable GPIO.

The pinctrl-msm driver also scans the "gpios" property to determine
which pins are available, and ensure that only those can be registered.

Support for QCOM8001 is removed as there is no longer any firmware that
implements it.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:08 +02:00
Timur Tabi f265e8b91b pinctrl: qcom: remove static globals to allow multiple TLMMs
Two data structures are declared as static globals but are intended to
be per-TLMM.  Move them into the msm_pinctrl structure and initialize
them at runtime.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:08 +02:00
Manivannan Sadhasivam 2242ddfbf4 pinctrl: actions: Add Actions S900 pinctrl driver
Add pinctrl driver for Actions Semi S900 SoC. The driver supports
pinctrl, pinmux and pinconf functionalities through a range of registers
common to both gpio driver and pinctrl driver.

Pinmux functionality is available only for the pin groups while the
pinconf functionality is available for both pin groups and individual
pins.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:08 +02:00
Chanho Park 4e21264abb pinctrl: samsung: add pin_dbg_show callback for debugfs
This patch adds a samsung_pin_dbg_show function to implement the
pin_dbg_show callback function which can be used to show pin
confuration values. Basically, it can show pin setting values by
accessing the "pins" node like below:

$ cat pins
pin 0 (gpy7-0)  CON(0x0) DAT(0x1) PUD(0x1) DRV(0x0) CON_PDN(0x0) PUD_PDN(0x0)

Signed-off-by: Chanho Park <parkch98@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:08 +02:00
Mika Westerberg c41eb2c7f9 pinctrl: sunrisepoint: Align GPIO number space with Windows
It turns out that the Windows GPIO driver for Sunrisepoint PCH-H uses
similar bank structure than it does for Cannon Lake with the exception
that here the bank size is always 24 pins. Starting from pad group E the
BIOS/Windows GPIO numbering does not match the hardware anymore but
instead there are gaps to make each pad group ("bank") consume exactly
24 pins. Because of this Linux does not use correct pins for
GpioIo/GpioIo resources exposed by the BIOS.

This patch aligns the GPIO number space with BIOS/Windows to make sure
the same numbering scheme is used in Linux as well following what we did
already for Intel Cannon Lake.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1543769
Reported-by: Vivien FRASCA <vivien.frasca@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:36:00 +02:00
Mika Westerberg 83b9dc1131 pinctrl: cherryview: Associate IRQ descriptors to irqdomain
When we dropped the custom Linux GPIO translation it resulted that the
IRQ numbers changed slightly as well. Normally this would be fine
because everyone is expected to use controller relative GPIO numbers and
ACPI GpioIo/GpioInt resources. However, there is a certain set of
Intel_Strago based Chromebooks where i8042 keyboard controller IRQ
number is hardcoded be 182 (this is corrected with newer coreboot but
the older ones still have the hardcoded Linux IRQ number). Because of
this hardcoded IRQ number keyboard on those systems accidentally broke
again.

Fix this by iteratively associating IRQ descriptors to the chip irqdomain
so that there are no gaps on those systems. Other systems are not
affected.

Fixes: 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199463
Reported-by: Sultan Alsawaf <sultanxda@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:35:59 +02:00
Yixun Lan b84e54616a pinctrl: meson-axg: fix the range of aobus bank
The GPIOAO bank is range from GPIOAO_0 to GPIOAO_13.

Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Reported-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-02 14:35:59 +02:00
Paweł Chmiel 938a10bb49 pinctrl: samsung: Document required order of banks
This patch documents requirement coming from the way
exynos_eint_gpio_irq() is working now, which expects EINTG banks to be
at the beginning of the bank arrays.

Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-04-18 17:48:39 +02:00
Paweł Chmiel 5cf9a338db pinctrl: samsung: Correct EINTG banks order
All banks with GPIO interrupts should be at beginning of bank array and
without any other types of banks between them.  This order is expected
by exynos_eint_gpio_irq, when doing interrupt group to bank translation.
Otherwise, kernel NULL pointer dereference would happen when trying to
handle interrupt, due to wrong bank being looked up.  Observed on
s5pv210, when trying to handle gpj0 interrupt, where kernel was mapping
it to gpi bank.

Cc: stable@vger.kernel.org
Fixes: 023e06dfa6 ("pinctrl: exynos: add exynos5410 SoC specific data")
Fixes: 608a26a7bc ("pinctrl: Add s5pv210 support to pinctrl-exynos)
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-04-18 17:45:08 +02:00
Linus Torvalds 1b2951dd99 This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
 
 - Nintendo Wii GameCube GPIO, known as "Hollywood"
 
 - Raspberry Pi mailbox service GPIO expander
 
 - Spreadtrum main SC9860 SoC and IEC GPIO controllers.
 
 Improvements:
 
 - Implemented .get_multiple() callback for most of the
   high-performance industrial GPIO cards for the ISA bus.
 
 - ISA GPIO drivers now select the ISA_BUS_API instead of
   depending on it. This is merged with the same pattern
   for all the ISA drivers and some other Kconfig cleanups
   related to this.
 
 Cleanup:
 
 - Delete the TZ1090 GPIO drivers following the deletion of
   this SoC from the ARM tree.
 
 - Move the documentation over to driver-api to conform with
   the rest of the kernel documentation build.
 
 - Continue to make the GPIO drivers include only
   <linux/gpio/driver.h> and not the too broad <linux/gpio.h>
   that we want to get rid of.
 
 - Managed to remove VLA allocation from two drivers pending
   more fixes in this area for the next merge window.
 
 - Misc janitorial fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJaxIehAAoJEEEQszewGV1zlEAP/3p3E6J8vPqJNV/C39c40krC
 ajo0ndiTC7cotmCXNQOl9xfMCTgkjBtx3WEKwTDfCsuWW+2YB0DRmMd0Bkf2RWjQ
 nM4rB64FzAu+rdD9jdGtfn24ofylSRFaHNQ/V8Prc2JVAXJt4DS97h+6kwzIAqCm
 A/xXQAx67k5qoTXLvR2n/8LX8TphSe2kwH/f/3/lJpNLfLCRRJ3GqJfpa72jw2eL
 4VIPc6KmttkqzJ1GFtzLPfhkhRr0p4sSzUNydlj5BKhmOSVu6Afv5ylgpK/p38dQ
 mGvNqFnU0lpwelsoZK75YikDFbqQjn4XkXJGvmIRMw4qM7crcw5oSkeMwCrcGqJW
 7Uo7NoQU94wcQSZTppFQdaJs7NHdcnpW7jcfRYYetZL/6eDGBtfxoym90Lyjvaqs
 y+ykofbadI0X/9omO5j+qozvIneLam/CF7iDRUb/5t1LJbNwtXUsVYhz3FuwPDt1
 ZHb6w+np9ZHN6H9jz3b/F9B/uQt54pshm7NorSXrJvZfKrv8kV14MoHgYsuQDDjV
 khbveygB8DwaPeV4XjpLeYhJB1L/Wjf46CVD6tyaCRDByGQmdoJEQF9QB2CxrF2J
 ouaaaS8tSC0IK/mKMMgJxC1Vr2gh0NMlQ3AL9EJDJvX+9RoIA2gwtBAiGnlEcdq3
 GyFAZ0szb5P4BaNnX9qc
 =C5t5
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.17 kernel cycle:

  New drivers:

   - Nintendo Wii GameCube GPIO, known as "Hollywood"

   - Raspberry Pi mailbox service GPIO expander

   - Spreadtrum main SC9860 SoC and IEC GPIO controllers.

  Improvements:

   - Implemented .get_multiple() callback for most of the
     high-performance industrial GPIO cards for the ISA bus.

   - ISA GPIO drivers now select the ISA_BUS_API instead of depending on
     it. This is merged with the same pattern for all the ISA drivers
     and some other Kconfig cleanups related to this.

  Cleanup:

   - Delete the TZ1090 GPIO drivers following the deletion of this SoC
     from the ARM tree.

   - Move the documentation over to driver-api to conform with the rest
     of the kernel documentation build.

   - Continue to make the GPIO drivers include only
     <linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
     want to get rid of.

   - Managed to remove VLA allocation from two drivers pending more
     fixes in this area for the next merge window.

   - Misc janitorial fixes"

* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: Add Spreadtrum PMIC EIC driver support
  gpio: Add Spreadtrum EIC driver support
  dt-bindings: gpio: Add Spreadtrum EIC controller documentation
  gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
  pinctrl: qcom: Don't allow protected pins to be requested
  gpiolib: Support 'gpio-reserved-ranges' property
  gpiolib: Change bitmap allocation to kmalloc_array
  gpiolib: Extract mask allocation into subroutine
  dt-bindings: gpio: Add a gpio-reserved-ranges property
  gpio: mockup: fix a potential crash when creating debugfs entries
  gpio: pca953x: add compatibility for pcal6524 and pcal9555a
  gpio: dwapb: Add support for a bus clock
  gpio: Remove VLA from xra1403 driver
  gpio: Remove VLA from MAX3191X driver
  gpio: ws16c48: Implement get_multiple callback
  gpio: gpio-mm: Implement get_multiple callback
  gpio: 104-idi-48: Implement get_multiple callback
  gpio: 104-dio-48e: Implement get_multiple callback
  gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
  gpio: pci-idio-16: Implement get_multiple callback
  ...
2018-04-05 09:51:41 -07:00
Linus Torvalds 77624cd2a7 Pin control bulk changes for the v4.17 kernel cycle:
New drivers:
 
 - Qualcomm SDM845: this is their new flagship SoC platform
   which seems to be targeted at premium mobile handsets.
 
 - Renesas R-Car M3-N SoC.
 
 - Renesas R8A77980 SoC.
 
 - NXP (ex Freescale) i.MX 6SLL SoC.
 
 - Mediatek MT2712 SoC.
 
 - Allwinner H6 SoC.
 
 Improvements:
 
 - Uniphier adds a few new functions and pins.
 
 - Renesas refactorings and additional pin definitions.
 
 - Improved pin groups for Axis Artpec6.
 
 Cleanup:
 
 - Drop the TZ1090 drivers. This platform is no longer
   maintained and is being deleted.
 
 - Drop ST-Ericsson U8540/U9540 support as this was never
   productified.
 
 - Overall minor fixes and janitorial.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJawz1oAAoJEEEQszewGV1zWUUQAJEIXW0vEsgwwFCIQYrKZBbi
 ovfQtpPgv5wbRmvLy/IaIFvO7eFedlOqjLTU0a3wuFZdHn9y0VkebVOjdG97TTeF
 g4fyqQ7pzdCKmxlDMm4zcOUycho9ZMa8lG3tKdyxI4tal6ygl81BypzKVi/WIxLA
 po2Vr1MHfKicWyPbgD1VRJV6oSzXSOMFkEcPUqx+6m5OM/GTKTKasU/fa4uu12jI
 OHF1TVr9glMbPiU0wC8bvKilgXCxhDYMYf1JCaxojr0Rt/DlR2vBgbfU7dIeRtO1
 MJ1nyJm0yZQfN/bBV1roSg/GGRS3jGbdHDzMnK8pI6LJNJYRa6vfLD/NHKUciSnf
 5cgpWloyvR+rbfObr6CYTirKE7iGBYvAH+do2TwmfvfwUYOI9lnbJrtnqtIovdVA
 R5FxrvI/Ol/j2t4V5wZGC1BBDsC6GH/1YV+W+n9fwKMdDIRgEsOTFsCNEWmSShWP
 Z53NzyZRVL32RK35g3WEqicfXOtmw3XXuHJZqWjlmXyVitEElMAVWySd6oG0HhvU
 sdRaoVGjXL9EVM3iZrqHtaRazRjItBA2CFnloC1PVjwi+dkHDcwWDvtOur+AF3wz
 VORi0xlWXd0Gzolo/ccsk7JUVmrkfCDnZx9uiTKQ+jgiSDfoEuQOvBfTI6LdeoNY
 upTZIfEhR/dMcjcdKIKe
 =IT6S
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control bulk updates from Linus Walleij:
 "New drivers:

   - Qualcomm SDM845: this is their new flagship SoC platform which
     seems to be targeted at premium mobile handsets.

   - Renesas R-Car M3-N SoC.

   - Renesas R8A77980 SoC.

   - NXP (ex Freescale) i.MX 6SLL SoC.

   - Mediatek MT2712 SoC.

   - Allwinner H6 SoC.

  Improvements:

   - Uniphier adds a few new functions and pins.

   - Renesas refactorings and additional pin definitions.

   - Improved pin groups for Axis Artpec6.

  Cleanup:

   - Drop the TZ1090 drivers. This platform is no longer maintained and
     is being deleted.

   - Drop ST-Ericsson U8540/U9540 support as this was never
     productified.

   - Overall minor fixes and janitorial"

* tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
  pinctrl: uniphier: add UART hardware flow control pin-mux settings
  pinctrl: sunxi: add support for the Allwinner H6 main pin controller
  pinctrl: sunxi: change irq_bank_base to irq_bank_map
  pinctrl: sunxi: introduce IRQ bank conversion function
  pinctrl: sunxi: refactor irq related register function to have desc
  pinctrl: msm8998: Remove owner assignment from platform_driver
  pinctrl: uniphier: divide I2S and S/PDIF audio out pin-mux group
  pinctrl: uniphier: add PXs2 Audio in/out pin-mux settings
  pinctrl/amd: poll InterruptEnable bits in enable_irq
  pinctrl: ocelot: fix gpio direction
  pinctrl: mtk: fix check warnings.
  pintcrl: mtk: support bias-disable of generic and special pins simultaneously
  pinctrl: add mt2712 pinctrl driver
  pinctrl: pinctrl-single: Fix pcs_request_gpio() when bits_per_mux != 0
  pinctrl: imx: Add pinctrl driver support for imx6sll
  dt-bindings: imx: update pinctrl doc for imx6sll
  pinctrl: intel: Implement intel_gpio_get_direction callback
  pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency
  pinctrl: mediatek: mtk-common: use true and false for boolean values
  pinctrl: sunxi: always look for apb block
  ...
2018-04-03 12:20:54 -07:00
Linus Torvalds f5a8eb632b arch: remove obsolete architecture ports
This removes the entire architecture code for blackfin, cris, frv, m32r,
 metag, mn10300, score, and tile, including the associated device drivers.
 
 I have been working with the (former) maintainers for each one to ensure
 that my interpretation was right and the code is definitely unused in
 mainline kernels. Many had fond memories of working on the respective
 ports to start with and getting them included in upstream, but also saw
 no point in keeping the port alive without any users.
 
 In the end, it seems that while the eight architectures are extremely
 different, they all suffered the same fate: There was one company
 in charge of an SoC line, a CPU microarchitecture and a software
 ecosystem, which was more costly than licensing newer off-the-shelf
 CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
 that all the SoC product lines are still around, but have not used the
 custom CPU architectures for several years at this point. In contrast,
 CPU instruction sets that remain popular and have actively maintained
 kernel ports tend to all be used across multiple licensees.
 
 The removal came out of a discussion that is now documented at
 https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
 marking any ports as deprecated but remove them all at once after I made
 sure that they are all unused. Some architectures (notably tile, mn10300,
 and blackfin) are still being shipped in products with old kernels,
 but those products will never be updated to newer kernel releases.
 
 After this series, we still have a few architectures without mainline
 gcc support:
 
 - unicore32 and hexagon both have very outdated gcc releases, but the
   maintainers promised to work on providing something newer. At least
   in case of hexagon, this will only be llvm, not gcc.
 
 - openrisc, risc-v and nds32 are still in the process of finishing their
   support or getting it added to mainline gcc in the first place.
   They all have patched gcc-7.3 ports that work to some degree, but
   complete upstream support won't happen before gcc-8.1. Csky posted
   their first kernel patch set last week, their situation will be similar.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJawdL2AAoJEGCrR//JCVInuH0P/RJAZh1nTD+TR34ZhJq2TBoo
 PgygwDU7Z2+tQVU+EZ453Gywz9/NMRFk1RWAZqrLix4ZtyIMvC6A1qfT2yH1Y7Fb
 Qh6tccQeLe4ezq5u4S/46R/fQXu3Txr92yVwzJJUuPyU0arF9rv5MmI8e6p7L1en
 yb74kSEaCe+/eMlsEj1Cc1dgthDNXGKIURHkRsILoweysCpesjiTg4qDcL+yTibV
 FP2wjVbniKESMKS6qL71tiT5sexvLsLwMNcGiHPj94qCIQuI7DLhLdBVsL5Su6gI
 sbtgv0dsq4auRYAbQdMaH1hFvu6WptsuttIbOMnz2Yegi2z28H8uVXkbk2WVLbqG
 ZESUwutGh8MzOL2RJ4jyyQq5sfo++CRGlfKjr6ImZRv03dv0pe/W85062cK5cKNs
 cgDDJjGRorOXW7dyU6jG2gRqODOQBObIv3w5efdq5OgzOWlbI4EC+Y5u1Z0JF/76
 pSwtGXA6YhwC+9LLAlnVTHG+yOwuLmAICgoKcTbzTVDKA2YQZG/cYuQfI5S1wD8e
 X6urPx3Md2GCwLXQ9mzKBzKZUpu/Tuhx0NvwF4qVxy6x1PELjn68zuP7abDHr46r
 57/09ooVN+iXXnEGMtQVS/OPvYHSa2NgTSZz6Y86lCRbZmUOOlK31RDNlMvYNA+s
 3iIVHovno/JuJnTOE8LY
 =fQ8z
 -----END PGP SIGNATURE-----

Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic

Pul removal of obsolete architecture ports from Arnd Bergmann:
 "This removes the entire architecture code for blackfin, cris, frv,
  m32r, metag, mn10300, score, and tile, including the associated device
  drivers.

  I have been working with the (former) maintainers for each one to
  ensure that my interpretation was right and the code is definitely
  unused in mainline kernels. Many had fond memories of working on the
  respective ports to start with and getting them included in upstream,
  but also saw no point in keeping the port alive without any users.

  In the end, it seems that while the eight architectures are extremely
  different, they all suffered the same fate: There was one company in
  charge of an SoC line, a CPU microarchitecture and a software
  ecosystem, which was more costly than licensing newer off-the-shelf
  CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
  seems that all the SoC product lines are still around, but have not
  used the custom CPU architectures for several years at this point. In
  contrast, CPU instruction sets that remain popular and have actively
  maintained kernel ports tend to all be used across multiple licensees.

  [ See the new nds32 port merged in the previous commit for the next
    generation of "one company in charge of an SoC line, a CPU
    microarchitecture and a software ecosystem"   - Linus ]

  The removal came out of a discussion that is now documented at
  https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
  marking any ports as deprecated but remove them all at once after I
  made sure that they are all unused. Some architectures (notably tile,
  mn10300, and blackfin) are still being shipped in products with old
  kernels, but those products will never be updated to newer kernel
  releases.

  After this series, we still have a few architectures without mainline
  gcc support:

   - unicore32 and hexagon both have very outdated gcc releases, but the
     maintainers promised to work on providing something newer. At least
     in case of hexagon, this will only be llvm, not gcc.

   - openrisc, risc-v and nds32 are still in the process of finishing
     their support or getting it added to mainline gcc in the first
     place. They all have patched gcc-7.3 ports that work to some
     degree, but complete upstream support won't happen before gcc-8.1.
     Csky posted their first kernel patch set last week, their situation
     will be similar

  [ Palmer Dabbelt points out that RISC-V support is in mainline gcc
    since gcc-7, although gcc-7.3.0 is the recommended minimum  - Linus ]"

This really says it all:

 2498 files changed, 95 insertions(+), 467668 deletions(-)

* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
  MAINTAINERS: UNICORE32: Change email account
  staging: iio: remove iio-trig-bfin-timer driver
  tty: hvc: remove tile driver
  tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
  serial: remove tile uart driver
  serial: remove m32r_sio driver
  serial: remove blackfin drivers
  serial: remove cris/etrax uart drivers
  usb: Remove Blackfin references in USB support
  usb: isp1362: remove blackfin arch glue
  usb: musb: remove blackfin port
  usb: host: remove tilegx platform glue
  pwm: remove pwm-bfin driver
  i2c: remove bfin-twi driver
  spi: remove blackfin related host drivers
  watchdog: remove bfin_wdt driver
  can: remove bfin_can driver
  mmc: remove bfin_sdh driver
  input: misc: remove blackfin rotary driver
  input: keyboard: remove bf54x driver
  ...
2018-04-02 20:20:12 -07:00
Stephen Boyd 691bf5d5a7 pinctrl: qcom: Don't allow protected pins to be requested
Some qcom platforms make some GPIOs or pins unavailable for use
by non-secure operating systems, and thus reading or writing the
registers for those pins will cause access control issues and
reset the device. With a DT/ACPI property to describe the set of
pins that are available for use, parse the available pins and set
the irq valid bits for gpiolib to know what to consider 'valid'.
This should avoid any issues with gpiolib. Furthermore, implement
the pinmux_ops::request function so that pinmux can also make
sure to not use pins that are unavailable.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 15:34:25 +02:00
Kunihiko Hayashi 4fc97ef94b pinctrl: uniphier: add UART hardware flow control pin-mux settings
UniPhier SoCs have the following pins for hardware flow control of UART:
  XRTS, XCTS
and for modem control of UART:
  XDTR, XDSR, XDCD, XRI

The port number with the flow control is SoC-dependent.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 15:14:43 +02:00
Icenowy Zheng c8a8309049 pinctrl: sunxi: add support for the Allwinner H6 main pin controller
The Allwinner H6 SoC has two pin controllers, one main controller
(called CPUX-PORT in user manual) and one controller in CPUs power
domain (called CPUS-PORT in user manual).

This commit introduces support for the main pin controller on H6.

The pin bank A and B are not wired out and hidden from the SoC's
documents, however it's shown that the "ATE" (an AC200 chip
co-packaged with the H6 die) is connected to the main SoC die via these
pin banks. The information about these banks is just copied from the BSP
pinctrl driver, but re-formatted to fit the mainline pinctrl driver
format. The GPIO functions are dropped, as they're impossible to use --
except a GPIO&IRQ only pin (PB20) which might be the IRQ of ATE.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 15:09:42 +02:00
Icenowy Zheng 35817d34bd pinctrl: sunxi: change irq_bank_base to irq_bank_map
The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5.

Change the current code that uses IRQ bank base to a IRQ bank map, in
order to support the case that holes exist among IRQ banks.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 15:07:49 +02:00
Icenowy Zheng 29dfc6bbcc pinctrl: sunxi: introduce IRQ bank conversion function
The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5. Some
refactors in the sunxi pinctrl framework are needed.

This commit introduces a IRQ bank conversion function, which replaces
the "(bank_base + bank)" code in IRQ register access.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 15:06:25 +02:00
Icenowy Zheng 4b0d6c5a00 pinctrl: sunxi: refactor irq related register function to have desc
As the new H6 SoC has holes in the IRQ registers, refactor the IRQ
related register function for getting the full pinctrl desc structure.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 15:04:10 +02:00
Fabio Estevam 27a3ba538b pinctrl: msm8998: Remove owner assignment from platform_driver
platform_driver does not need to set the owner field, as this will
be populated by the driver core.

Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 14:05:11 +02:00
Katsuhiro Suzuki a5af5c9f87 pinctrl: uniphier: divide I2S and S/PDIF audio out pin-mux group
This patch divides large pin-mux group 'aio' of UniPhier LD11/LD20
to 2 groups as following:
  aout1   : 8ch I2S output: AO1DACCK, AO1BCK, AO1LRCK, AO1D[0-2]
  aoutiec1: S/PDIF output : AO1IEC, AO1ARC

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 13:36:15 +02:00
Katsuhiro Suzuki 38eae3fa9d pinctrl: uniphier: add PXs2 Audio in/out pin-mux settings
The UniPhier PXs2 SoC audio core use following 25 pins:
  ain1    : 2ch I2S input : AI1ADCCK, AI1BCK, AI1D0, AI1LRCK
  ain2    : 8ch I2S input : AI2ADCCK, AI2BCK, AI2D[0-3], AI2LRCK
  ainiec1 : S/PDIF input  : XIRQ17 (for AO1IEC)
  aout2   : 8ch I2S output: AO2BCK, AO2D0, AO2DACCK, AO2LRCK
                            PORT226, 227, 230 (for AO2D[1-3])
  aout3   : 2ch I2S output: AO3BCK, AO3DMIX, AO3DACCK, AO3LRCK
  aoutiec1: S/PDIF output : PORT132(for AO1IEC)
  aoutiec2: S/PDIF output : AO2IEC

Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-27 13:35:00 +02:00
Arnd Bergmann f59b2dc2de pinctrl: remove adi2/blackfin drivers
The blackfin architecture is getting removed, so these are
now obsolete.

Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-26 15:56:55 +02:00
Daniel Kurtz 4c1de0414a pinctrl/amd: poll InterruptEnable bits in enable_irq
In certain cases interrupt enablement will be delayed relative to when
the InterruptEnable bits are written.  One example of this is when
a GPIO's "debounce" logice is first enabled.  After enabling debounce,
there is a 900 us "warm up" period during which InterruptEnable[0]
(bit 11) will read as 0 despite being written 1.  During this time
InterruptSts will not be updated, nor will interrupts be delivered, even
if the GPIO's interrupt configuration has been written to the register.

To work around this delay, poll the InterruptEnable bits after setting
them to ensure interrupts have truly been enabled in hardware before
returning from the irq_enable handler.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26 11:09:49 +02:00
Alexandre Belloni 44edff1bbc pinctrl: ocelot: fix gpio direction
Bits have to be cleared in DEVCPU_GCB:GPIO:GPIO_OE for input and set for
output. ocelot_gpio_set_direction() got it wrong and this went unnoticed
when the driver was reworked.

Reported-by: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26 11:04:48 +02:00
Zhiyong Tao e6c462d3ec pinctrl: mtk: fix check warnings.
This patch fixes check warnings.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26 10:58:33 +02:00
Zhiyong Tao 6af8df4c67 pintcrl: mtk: support bias-disable of generic and special pins simultaneously
For generic pins, parameter "arg" is 0 or 1.
For special pins, bias-disable is set by R0R1,
so we need transmited "00" to set bias-disable
When we set "bias-disable" as high-z property,
the parameter should be "MTK_PUPD_SET_R1R0_00".

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26 10:56:54 +02:00
Zhiyong Tao 8670710ff8 pinctrl: add mt2712 pinctrl driver
The commit includes mt2712 pinctrl driver.

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26 10:53:39 +02:00
David Lechner 45dcb54f01 pinctrl: pinctrl-single: Fix pcs_request_gpio() when bits_per_mux != 0
This fixes pcs_request_gpio() in the pinctrl-single driver when
bits_per_mux != 0. It appears this was overlooked when the multiple
pins per register feature was added.

Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-26 10:48:17 +02:00
Bai Ping 864670d534 pinctrl: imx: Add pinctrl driver support for imx6sll
Add pinctrl driver support for imx6sll.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 04:16:10 +01:00
Javier Arteaga 67e6d3e83c pinctrl: intel: Implement intel_gpio_get_direction callback
Allows querying GPIO direction from the pad config register.
If the pad is not in GPIO mode, return an error.

Signed-off-by: Javier Arteaga <javier@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 04:07:22 +01:00
Masahiro Yamada 86822c2f3a pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.

Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.

Detected by "make ARCH=score allyesconfig".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 04:04:40 +01:00
Gustavo A. R. Silva b2f78906d5 pinctrl: mediatek: mtk-common: use true and false for boolean values
Assign true or false to boolean variables instead of an integer value.

This issue was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 04:02:40 +01:00
Andre Przywara a34ea4b40f pinctrl: sunxi: always look for apb block
The Allwinner pinctrl device tree binding suggests that a clock named
"apb" would drive the pin controller IP. However (for legacy reasons) we
rely on this clock actually being the first clock defined.
Since named clocks can be in any order, let's explicitly check for a
clock called "apb" if there is more than one clock referenced.

Kudo to Maxime for suggesting this much more elegant approach.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 03:43:48 +01:00
Linus Walleij b6d09f7807 pinctrl: nomadik: Drop U8540/9540 support
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.

Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-23 03:38:14 +01:00
Linus Walleij 76a16885a7 pinctrl: sh-pfc: Updates for v4.17 (take two)
- Add USB pin groups on R-Car M3-N,
   - Add support for the new R-Car V3H SoC,
   - Add EtherAVB pin groups on R-Car V3M,
   - Miscellaneous fixes and cleanups.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJas+IJAAoJEEgEtLw/Ve77034P/037wFBewWZSj1+/5cGMQ9Cm
 NJtWyPMXlmTW7pzT59Q6rErePnC21oCp33tYAeC3+Pja3IbCj2UDHStravEFRlXb
 0n7caWWudHl4aPmDWhtzfDs6+NSUWaFCrz8kbwQVHrYU1RhAMtP2vZVFV0af/5EB
 paQkUItYDYGG5Rjc9Sz/L3PegvAbJ8Wt+61jETLU4DMTa1ZGDWXL7YC8DTAkULGM
 xCCNoj5x3UJfbY6MhqmPG5EOmjEOUvi8cQcW/Ch2JQkojNf1U1WnsRUL5DNkBHiE
 Zrttn8+y02ssIpjYdpmw/KU/tpMGdtoRnhGrBfeeb9HDOqw3q8Lb7XDR7/wVxdKD
 nvbb8urWj3UiHCVlAebqu3vAuhFPR2wq3LXMv5/7/BJRjAjhQRtkLiEJl41WGQlZ
 BIITfcQ7Yv2EZ+6fahmZHQ2BcEoTBfOg8Y6yEjmRHXV6gO27IIx0cjp8xKbLjGWz
 a3zyT+LYSNJhO47QpgOCwHbuXiiExAoRiUChLDhrgd75s6qFQ5kX0gtWyTGUNgam
 Q60zD1Vx2+LXD0B4K1gYkrMqLZy081sxinRC7I7B0xKPU/gXz8yvGhZW8cQpunRd
 VOb9rkYu5ec51/7oRuwb4aoHtV5IGDxri5T/8R/0zpwVZwJJ4YWS0OJuYufVS3hX
 6bWdE9+32/c8CVfHt5zX
 =swQl
 -----END PGP SIGNATURE-----

Merge tag 'sh-pfc-for-v4.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.17 (take two)

  - Add USB pin groups on R-Car M3-N,
  - Add support for the new R-Car V3H SoC,
  - Add EtherAVB pin groups on R-Car V3M,
  - Miscellaneous fixes and cleanups.
2018-03-23 03:36:48 +01:00
Ulrich Hecht a6fff41f41 pinctrl: sh-pfc: r8a77995: Deduplicate VIN4 pin definitions
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-21 18:25:48 +01:00
Ulrich Hecht a5c2949ff7 pinctrl: sh-pfc: r8a7796: Deduplicate VIN4 pin definitions
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-21 18:25:48 +01:00
Ulrich Hecht 9942a5b529 pinctrl: sh-pfc: r8a7795: Deduplicate VIN4 pin definitions
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-21 18:25:47 +01:00
Ulrich Hecht 4fd82963e1 pinctrl: sh-pfc: r8a77995: Correct VIN4 18-bit pins
RGB666 has a pin assignment that differs from the other formats.

Fixes: fbd452aeb4 ("pinctrl: sh-pfc: r8a77995: Add VIN4 pins, groups and function")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-21 18:25:22 +01:00
Ulrich Hecht a66b68ba7f pinctrl: sh-pfc: r8a7796: Correct VIN4 18-bit pins
RGB666 has a pin assignment that differs from the other formats.

Fixes: 8db6cbabac ("pinctrl: sh-pfc: r8a7796: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-21 18:25:01 +01:00
Ulrich Hecht b538dc5bbb pinctrl: sh-pfc: r8a7795: Correct VIN4 18-bit pins
RGB666 has a pin assignment that differs from the other formats.

Fixes: 6b4de40810 ("pinctrl: sh-pfc: r8a7795: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-21 18:24:16 +01:00
Geert Uytterhoeven 3b047a9597 pinctrl: sh-pfc: r8a77995: Rename EtherAVB "mdc" pin group to "mdio"
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.

Fixes: 66abd968d0 ("pinctrl: sh-pfc: r8a77995: Add EthernetAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
2018-03-21 18:18:32 +01:00
Geert Uytterhoeven f7ce295cfd pinctrl: sh-pfc: r8a77965: Rename EtherAVB "mdc" pin group to "mdio"
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.

Fixes: fa3e8b71b9 ("pinctrl: sh-pfc: r8a77965: Add EtherAVB groups/functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
2018-03-21 18:18:30 +01:00
Geert Uytterhoeven 350aba9a74 pinctrl: sh-pfc: r8a7796: Rename EtherAVB "mdc" pin group to "mdio"
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.

Fixes: 41397032c4 ("pinctrl: sh-pfc: r8a7796: Add group for AVB MDIO and MII pins")
Fixes: 9c99a63ec7 ("pinctrl: sh-pfc: r8a7796: Add EtherAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
2018-03-21 18:18:25 +01:00
Geert Uytterhoeven 24cfe1a970 pinctrl: sh-pfc: r8a7795-es1: Rename EtherAVB "mdc" pin group to "mdio"
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.

Fixes: b25719eb93 ("pinctrl: sh-pfc: r8a7795: Add group for AVB MDIO and MII pins")
Fixes: 819fd4bfcc ("pinctrl: sh-pfc: r8a7795: add EtherAVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
2018-03-21 18:18:23 +01:00
Geert Uytterhoeven cbe0dd9ad5 pinctrl: sh-pfc: r8a7795: Rename EtherAVB "mdc" pin group to "mdio"
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.

Fixes: 30c078de6f ("pinctrl: sh-pfc: r8a7795: Add EtherAVB pins, groups and function")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
2018-03-21 18:18:18 +01:00
Geert Uytterhoeven 43a51cd5d6 pinctrl: sh-pfc: Add SH_PFC_PIN_GROUP_ALIAS()
Add a macro to refer to another pin group with a different name.

This will be used to rename wrongly-named pin groups, while retaining
backwards compatibility with old DTBs.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
2018-03-21 18:18:05 +01:00
Geert Uytterhoeven 66e9fe1ec7 pinctrl: sh-pfc: r8a7790: Add missing TX_ER pin to avb_mii group
The pin controller drivers for all R-Car Gen2 SoCs have entries for the
EtherAVB TX_ER pins in their EtherAVB MII groups, except on R-Car H2.

Add the missing pin to restore consistency.

Note that technically TX_ER is an optional signal in the MII bus, and
thus could have its own group, but this is currently not supported by
any R-Car Gen2 pin controller driver.

Fixes: 19ef697d1e ("sh-pfc: r8a7790: add EtherAVB pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-21 18:16:51 +01:00
Sergei Shtylyov b3cbd8a567 pinctrl: sh-pfc: r8a77970: Add EtherAVB pin groups
Add the EtherAVB pin groups to the R8A77970 PFC driver.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-14 14:39:52 +01:00
Sergei Shtylyov f59125248a pinctrl: sh-pfc: Add R8A77980 PFC support
Add the PFC support for the R8A77980 SoC including pin groups for some
on-chip devices such as AVB, CAN-FD, GETHER, [H]SCIF, I2C, INTC-EX, MMC,
MSIOF, PWM, and VIN...

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-09 13:55:30 +01:00
Sergei Shtylyov c21a3e30e8 pinctrl: sh-pfc: Add PORT_GP_CFG_25() helper macro
They follow the style of the existing PORT_GP_CFG_<n>() macros and
will be used by a follow-up patch for the R8A77980 SoC.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-09 13:55:26 +01:00
Krzysztof Kozlowski 93b0beae72 pinctrl: samsung: Validate alias coming from DT
Driver uses alias from Device Tree as an index of pin controller data
array.  In case of a wrong DTB or an out-of-tree DTB, the alias could be
outside of this data array leading to out-of-bounds access.

Depending on binary and memory layout, this could be handled properly
(showing error like "samsung-pinctrl 3860000.pinctrl: driver data not
available") or could lead to exceptions.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org>
Fixes: 30574f0db1 ("pinctrl: add samsung pinctrl and gpiolib driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-08 13:02:26 +01:00
Niklas Söderlund 625504aeff pinctrl: sh-pfc: r8a7795: remove duplicate of CLKOUT pin in pinmux_pins[]
When adding GP-1-28 port pin support it was forgotten to remove the
CLKOUT pin from the list of pins that are not associated with a GPIO
port in pinmux_pins[]. This results in a warning when reading the
pinctrl files in sysfs as the CLKOUT pin is still added as a none GPIO
pin. Fix this by removing the duplicated entry which is no longer
needed.

~ # cat /sys/kernel/debug/pinctrl/e6060000.pin-controller/pinconf-pins
[   89.432081] ------------[ cut here ]------------
[   89.436904] Pin 496 is not in bias info list
[   89.441252] WARNING: CPU: 1 PID: 456 at drivers/pinctrl/sh-pfc/core.c:408 sh_pfc_pin_to_bias_reg+0xb0/0xb8
[   89.451002] CPU: 1 PID: 456 Comm: cat Not tainted 4.16.0-rc1-arm64-renesas-00048-gdfafc344a4f24dde #12
[   89.460394] Hardware name: Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+ (DT)
[   89.468910] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[   89.473747] pc : sh_pfc_pin_to_bias_reg+0xb0/0xb8
[   89.478495] lr : sh_pfc_pin_to_bias_reg+0xb0/0xb8
[   89.483241] sp : ffff00000aff3ab0
[   89.486587] x29: ffff00000aff3ab0 x28: ffff00000893c698
[   89.491955] x27: ffff000008ad7d98 x26: 0000000000000000
[   89.497323] x25: ffff8006fb3f5028 x24: ffff8006fb3f5018
[   89.502690] x23: 0000000000000001 x22: 00000000000001f0
[   89.508057] x21: ffff8006fb3f5018 x20: ffff000008bef000
[   89.513423] x19: 0000000000000000 x18: ffffffffffffffff
[   89.518790] x17: 0000000000006c4a x16: ffff000008d67c98
[   89.524157] x15: 0000000000000001 x14: ffff00000896ca98
[   89.529524] x13: 00000000cce5f611 x12: ffff8006f8d3b5a8
[   89.534891] x11: ffff00000981e000 x10: ffff000008befa08
[   89.540258] x9 : ffff8006f9b987a0 x8 : ffff000008befa08
[   89.545625] x7 : ffff000008137094 x6 : 0000000000000000
[   89.550991] x5 : 0000000000000000 x4 : 0000000000000001
[   89.556357] x3 : 0000000000000007 x2 : 0000000000000007
[   89.561723] x1 : 1ff24f80f1818600 x0 : 0000000000000000
[   89.567091] Call trace:
[   89.569561]  sh_pfc_pin_to_bias_reg+0xb0/0xb8
[   89.573960]  r8a7795_pinmux_get_bias+0x30/0xc0
[   89.578445]  sh_pfc_pinconf_get+0x1e0/0x2d8
[   89.582669]  pin_config_get_for_pin+0x20/0x30
[   89.587067]  pinconf_generic_dump_one+0x180/0x1c8
[   89.591815]  pinconf_generic_dump_pins+0x84/0xd8
[   89.596476]  pinconf_pins_show+0xc8/0x130
[   89.600528]  seq_read+0xe4/0x510
[   89.603789]  full_proxy_read+0x60/0x90
[   89.607576]  __vfs_read+0x30/0x140
[   89.611010]  vfs_read+0x90/0x170
[   89.614269]  SyS_read+0x60/0xd8
[   89.617443]  __sys_trace_return+0x0/0x4
[   89.621314] ---[ end trace 99c8d0d39c13e794 ]---

Fixes: 82d2de5a4f ("pinctrl: sh-pfc: r8a7795: Add GP-1-28 port pin support")
Reviewed-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-08 13:02:01 +01:00
Takeshi Kihara c490b28f36 pinctrl: sh-pfc: r8a77965: Add USB3.0 host pins, groups and functions
This patch adds USB30 (USB3.0 host) pin, group and function to
the R8A77965 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-05 11:03:47 +01:00
Takeshi Kihara 0d75f8dae3 pinctrl: sh-pfc: r8a77965: Add USB2.0 host pins, groups and functions
This patch adds USB{0,1} (USB2.0 host) pins, groups and functions to
the R8A77965 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-03-05 11:02:32 +01:00
Linus Walleij e024484a86 pinctrl: sh-pfc: Updates for v4.17
- Add DU and VIN pin groups on R-Car D3,
   - Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
   - Add support for the new R-Car M3-N SoC,
   - Small fixes and cleanups.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJamSLtAAoJEEgEtLw/Ve77Qb0QAIaVFrBq4OAfQGTU5wYrJvl2
 OMNjt7oPf4LHxqlo979peJ3nxfMZxMCZ1MCIzHEF1hKaOb+PJMrWILt71UJwNnUY
 TSAgtZUtl6LUxl2F/ZJ7DiqUTKog8m/jfYwgbdva+FlSNd3pWUYCNFX00SGDtonR
 E/hrx4XYFM+EBuIVrccw/U1u1Cx6FjSEbG7QjBLXlu8ZxBAvHI3V8lyOv0p1jzBt
 hqNQHsa6O/D2NDypTUCL8Bqe+otZvfnJwQvrNWF7pZBF3m/vaWOROBecZ/QajpPf
 RftyFEVvtoyeViG7cD0P6h7G0I8kEbzNFODIfLYXjgsNJt88BtotyRTZI/vRG5Ob
 BSFfkAe4JkRux/7Ry6y/ptMJSZUJcjXo3w8xFXj/DqpA6A+1EyKCypGil6eiGH9q
 5kJHpYVDtoQSINWKmOTlu1MQXOo1P+IpYJDgYDOLOHxurRyRQWVW8htRe8zh8WTu
 4ikvP8s0kAv7MupISsNUTnwuVD2IdJyaKoMDh6stZOKu0cWzV/+tUOefEZ0xx0HF
 OeYll9iNrJh0OmIj+wyN770BbaR2q8Gq6W26dxJRAhupGVJw/PrmzDMdqb2FTASp
 20Xrjo2ppIZ4AlWgN8Mx5ZPIaVhLS5pmZ2O1CrFQI34a8ZjO3GA72Jx8dUYNh1lS
 7Kyn6eCXLbkVbfx9UMUV
 =mYK2
 -----END PGP SIGNATURE-----

Merge tag 'sh-pfc-for-v4.17-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.17

  - Add DU and VIN pin groups on R-Car D3,
  - Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
  - Add support for the new R-Car M3-N SoC,
  - Small fixes and cleanups.
2018-03-02 13:38:12 +01:00
Richard Fitzgerald 8b1b2dc7b4 pinctrl: core: Add missing EXPORT on pinctrl_register_mappings
Systems that don't have devicetree need pinctrl_register_mappings.
It should be EXPORT_SYMBOL_GPL so that it can be called from
pinctrl drivers built as modules.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-02 11:05:35 +01:00
Martin Blumenstingl 55af415b42 pinctrl: meson: meson8b: fix requesting GPIOs greater than GPIOZ_3
Meson8b is a cost reduced variant of the Meson8 SoC. It's package size
is smaller than Meson8.
Unfortunately there are a few key differences which cannot be seen
without close inspection of the code and the public S805 datasheet:
- the GPIOX bank is missing the GPIOX_12, GPIOX_13, GPIOX_14 and
  GPIOX_15 GPIOs
- the GPIOY bank is missing the GPIOY_2, GPIOY_4, GPIOY_5, GPIOY_15 and
  GPIOY_16 GPIOs
- the GPIODV bank is missing all GPIOs except GPIODV_9, GPIODV_24,
  GPIODV_25, GPIODV_26, GPIODV_27, GPIODV_28 and GPIODV_29
- the GPIOZ bank is missing completely
- there is a new GPIO bank called "DIF"

This means that Meson8b only has 83 actual GPIO lines. Without any holes
there would be 130 GPIO lines in total (120 are inherited from Meson8
plus 10 new from the DIF bank).

GPIOs greater GPIOZ_3 (whose ID is 83 - as a reminder: this is exactly
the number of actual GPIO lines on Meson8b and also the value of
meson8b_cbus_pinctrl_data.num_pins) cannot berequested. Using CARD_6
(which used ID 100 prior to this patch, "base of the GPIO controller was
382) as an example:
$ echo 482 > /sys/class/gpio/export
export_store: invalid GPIO 482

This removes all non-existing pins from to dt-bindings header file
(include/dt-bindings/gpio/meson8b-gpio.h). This allows us to have a
consecutive numbering for the GPIO #defines (GPIOY_2 doesn't exist for
example, so previously the GPIOY_3 ID was "GPIOY_1 + 2", after this
patch it is "GPIOY_1 + 1"). As a nice side-effect this means that we get
compile-time (instead of runtime) errors if Meson8b .dts uses a pin that
only exists on Meson8.

Additionally the pinctrl-meson8b driver has to be updated to handle this
new GPIO numbering. By default a struct meson_bank only handles GPIO
banks where the pins are numbered consecutively because it calculates
the bit offsets based on the GPIO IDs.
This is solved by  taking the original BANK() definition and splitting it
into consecutive subsets (X0..11 and X16..21). The bit offsets for each
new bank includes the skipped GPIOs (the definition of the "X0..11" bank
is identical to the old "X" bank apart from the "last IRQ" field, the
definition of the new, split "X16..21" bank takes the original "X" bank
and adds 16 - the start of the new split bank - to the "first IRQ",
pullen bit, pull bit, dir bit, out bit and in bit).

Commit 984cffdeae ("pinctrl: Fix gpio/pin mapping for Meson8b")
fixed the same issue by setting "ngpio" (of the gpio_chip) to 130.
Unfortunately this broke in db80f0e158 ("pinctrl: meson: get rid of
unneeded domain structures").
The solution from this patch was considered to be better than the
previous attempt at fixing this because it provides compile-time error
checking for the GPIOs that exist on Meson8 but don't exist on Meson8b.

The following pins were tested on an Odroid-C1 using the sysfs GPIO
interface checking that their value (high or low) could be read:
- GPIOX_0, GPIOX_1, GPIOX_2, GPIOX_3, GPIOX_4, GPIOX_5, GPIOX_6,
  GPIOX_7, GPIOX_8, GPIOX_9, GPIOX_10, GPIOX_11, GPIOX_18, GPIOX_19,
  GPIOX_20, GPIOX_21
- GPIOY_3, GPIOY_7, GPIOY_8
(some of these had to be pulled up because they were low by default,
others were high by default so these had to be pulled down)

Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-02 10:46:42 +01:00
Richard Fitzgerald b89405b610 pinctrl: devicetree: Fix dt_to_map_one_config handling of hogs
When dt_to_map_one_config() is called with a pinctrl_dev passed
in, it should only be using this if the node being looked up
is a hog. The code was always using the passed pinctrl_dev
without checking whether the dt node referred to it.

A pin controller can have pinctrl-n dependencies on other pin
controllers in these cases:

- the pin controller hardware is external, for example I2C, so
  needs other pin controller(s) to be setup to communicate with
  the hardware device.

- it is a child of a composite MFD so its of_node is shared with
  the parent MFD and other children of that MFD. Any part of that
  MFD could have dependencies on other pin controllers.

Because of this, dt_to_map_one_config() can't assume that if it
has a pinctrl_dev passed in then the node it looks up must be
a hog. It could be a reference to some other pin controller.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-02 09:41:21 +01:00
Radoslaw Pietrzyk 430a2a5945 pinctrl: stm32: Optimizes and enhances stm32gpio irqchip
- removes unneeded irq_chip.irq_eoi callback
- adds irq_chip.irq_set_wake callback for possible
  in the future GPIO wakeup
- adds irq_chip.irq_ack callback

Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-02 08:40:31 +01:00
Jesper Nilsson 41e009b2b5 pinctrl: artpec-6: Add smaller groups for uarts
Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.

This allows us to be more precise in which pins we're
actually using.

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-01 17:04:09 +01:00
James Hogan 4a7cba71ca pinctrl: Drop TZ1090 drivers
Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 pinctrl drivers. They are of no value without the
architecture and SoC platform code.

Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-01 15:34:15 +01:00
Takeshi Kihara a8ab4f2bd8 pinctrl: sh-pfc: r8a77965: Add support for INTC-EX IRQ pins
Most pins on the R8A77965 SoC can be configured in GPIO mode for
interrupt and GPIO functionality, while a couple of them can also
be routed to the INTC-EX hardware block (formerly known as IRQC).

On R8A77965 the INTC-EX hardware handles pins IRQ0 -> IRQ5 and
this patch adds support for them to the PFC driver as "intc_ex_irqN".

Based on a similar patch for the R8A7795 PFC driver by Magnus Damm
<damm+renesas@opensource.se>.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-28 09:17:54 +01:00
Ulrich Hecht fbd452aeb4 pinctrl: sh-pfc: r8a77995: Add VIN4 pins, groups and function
This patch adds VIN4 pins, groups and function for the
R8A77995 (D3) SoC.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-26 10:19:03 +01:00
Ulrich Hecht 6b4de40810 pinctrl: sh-pfc: r8a7795: Add VIN4, VIN5 pins, groups and functions
This patch adds VIN4 and VIN5 pins, groups and functions for the
R8A7795 SoC.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-26 10:19:03 +01:00
Ulrich Hecht 8db6cbabac pinctrl: sh-pfc: r8a7796: Add VIN4, VIN5 pins, groups and functions
This patch adds VIN4 and VIN5 pins, groups and functions for the
R8A7796 SoC.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-26 10:19:03 +01:00
Phil Reid fa2b7fae84 pinctrl: mcp23s08: add open drain configuration for irq output
The mcp23s08 series device can be configured for wired and interrupts
using an external pull-up and open drain output via the IOCON_ODR bit.
And "drive-open-drain" property to enable this.

Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 16:08:59 +01:00
Phil Reid d9f50048dc pinctrl: mcp23s08: fix probing of mcp23s18
one_regmap_config is always null if mcp type is MCP_TYPE_S18.
Remove the null check so that the mcp23s18 will probe.

Fixes: 1781af563a ("pinctrl: mcp23s08: spi: Fix duplicate pinctrl debugfs entries")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 16:04:26 +01:00
Daniel Kurtz 12b10f47e5 pinctrl/amd: add get_direction handler
On boot, gpiochip_add_data() initializes the FLAG_IS_OUT bit in
desc->flags iff its gpio_chip does not have ->direction_input() handler,
else it is initialized to 0, which implies the GPIO is an "input".

Later, the sysfs "direction" handler will use gpiod_get_direction() to
get the current direction, but if no ->get_direction() handler is
installed, the result will just be the current (initial) value of flags,
which will always be OUT irregardless of the initial register value.

Add a get_direction() handler to pinctrl-amd to fix this and always
provide the correct value for direction.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 15:52:19 +01:00
Andy Shevchenko b5520891a3 pinctrl: Re-use DEFINE_SHOW_ATTRIBUTE() macro
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 15:36:03 +01:00
Colin Ian King ce3e7f0ee9 pinctrl: ocelot: make function ocelot_pinctrl_probe static
The function ocelot_pinctrl_probe is local to the source and does not
need to be in global scope, so make it static.

Cleans up sparse warning:
drivers/pinctrl/pinctrl-ocelot.c:465:5: warning: symbol
'ocelot_pinctrl_probe' was not declared. Should it be static?

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-22 14:02:18 +01:00
Jacopo Mondi fa3e8b71b9 pinctrl: sh-pfc: r8a77965: Add EtherAVB groups/functions
Add EtherAVB groups and functions definitions for R-Car M3-N.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:33:02 +01:00
Jacopo Mondi 58cfd7f37e pinctrl: sh-pfc: r8a77965: Add SCIFs groups/functions
Add SCIF[0-5] groups and pin function definitions for R-Car M3-N.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:32:59 +01:00
Jacopo Mondi 490e687eb8 pinctrl: sh-pfc: Initial R-Car M3-N support
Add initial PFC support for R-Car M3-N (r8a77965) SoC.
No groups or functions defined, just pin and registers enumeration.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:32:58 +01:00
Takeshi Kihara 74965de1ca pinctrl: sh-pfc: r8a7796: Add TMU pins, groups and functions
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7796 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:03:29 +01:00
Takeshi Kihara f0442cf27c pinctrl: sh-pfc: r8a7795-es1: Add TMU pins, groups and functions
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7795 ES1.x SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:03:26 +01:00
Takeshi Kihara edcc14c82d pinctrl: sh-pfc: r8a7795: Add TMU pins, groups and functions
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7795 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:03:23 +01:00
Takeshi Kihara 71c236adf0 pinctrl: sh-pfc: r8a7796: Add HDMI pins, groups and functions
This patch adds HDMI0 CEC pin, group and function to the R8A7796 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:03:18 +01:00
Takeshi Kihara 1240414859 pinctrl: sh-pfc: r8a7795-es1: Add HDMI pins, groups and functions
This patch adds HDMI0 CEC pin, group and function to
the R8A7795 ES1.x SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: fixed typo in comment]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:03:15 +01:00
Takeshi Kihara 5722110e2f pinctrl: sh-pfc: r8a7795: Add HDMI pins, groups and functions
This patch adds HDMI0 CEC pin, group and function to the R8A7795 SoC.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: fixed typo in comment]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:02:56 +01:00
Takeshi Kihara 8b446c4d38 pinctrl: sh-pfc: r8a7796: Fix IPSR and MOD_SEL register pin assignment for NDFC pins group
This patch fixes to set IPSR and MOD_SEL when using NFDATA{14,15}_A and
NF{RB,WP}_N_A pin function is selected. And renamess MOD_SEL2 bit22 value
definition name to SEL_NDFC.

This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.53E.

Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:02:20 +01:00
Takeshi Kihara b418c4609d pinctrl: sh-pfc: r8a7796: Fix MOD_SEL register pin assignment for SSI pins group
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.

This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.

Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:02:16 +01:00
Takeshi Kihara 740a4a3aa7 pinctrl: sh-pfc: r8a7795: Fix MOD_SEL register pin assignment for SSI pins group
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.

This is a correction because MOD_SEL register specification for R8A7795
ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.

Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 19:02:10 +01:00
Ulrich Hecht 65a90f046b pinctrl: sh-pfc: r8a77995: Add DU pins, groups and function
This patch adds DU pins, groups and function for the R8A77995 (D3) SoC.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-20 16:19:03 +01:00
Linus Walleij 5da2bd5ad5 pinctrl: nomadik: add USB functions for STn8815
The MUSB block in the Nomadik has two pin settings: high speed or
full speed. These correspond to two unique pin group settings: all
pins set to function B for high speed and all set to function C
for full speed. Full speed uses more pins than high speed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-13 08:18:17 +01:00
Markus Elfring 2580b1ceb7 pinctrl: sh-pfc: Use seq_puts() in sh_pfc_pin_dbg_show()
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2018-02-12 15:27:58 +01:00
Yixun Lan 49527bc0e8 pinctrl: meson-axg: adjust uart_ao_b pin group naming
Simply adjust the pin group to _x _y _z style, as to
keep the consistency in DT with previous naming scheme.

Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12 10:47:36 +01:00
Bjorn Andersson a7aa75a2a7 pinctrl: msm: Use dynamic GPIO numbering
The base of the TLMM gpiochip should not be statically defined as 0, fix
this to not artificially restrict the existence of multiple pinctrl-msm
devices.

Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12 10:47:24 +01:00
Jan Kundrát 1781af563a pinctrl: mcp23s08: spi: Fix duplicate pinctrl debugfs entries
This is a bit more involved because the pinctrl core so far always
assumed that one device (with a unique dev_name) only contains a single
pinctrl thing. This is not true for the mcp23s08 driver for chips
connected over SPI. They have a "logical address" which means that
several chips can share one physical CS signal.

A downside of this patch are some possibly ugly names for the debugfs
entries, such as "spi1.1-mcp23xxx-pinctrl.2", etc.

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12 10:47:24 +01:00
Jan Kundrát ed23175141 pinctrl: mcp23s08: spi: Add HW address to gpio_chip.label
When several devices are sharing one hardware SPI CS, there is no visual
clue in `lsgpio` or in /sys/kernel/debug/gpio about which one is which
one. Stuff depends on the enumeration order, and therefore lower chip
addresses always go first, but that's just an implementation detail.
This change includes the device-specific address in the debug output:

  gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17.2, can sleep:
  gpiochip3: GPIOs 480-495, parent: spi/spi1.1, mcp23s17.1, can sleep:

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12 10:47:24 +01:00
Jan Kundrát 9b3e420766 pinctrl: mcp23s08: spi: Fix regmap debugfs entries
The SPI version of this chip allows several devices to be present on the
same SPI bus via a local address. If this is in action and if the kernel
has debugfs, however, the code attempts to create duplicate entries for
the regmap's debugfs:

  mcp23s08 spi1.1: Failed to create debugfs directory

This patch simply assigns a local name matching the device logical
address to the `struct regmap_config`.

No changes are needed for MCP23S18 because that device does not support
any logical addressing. Similarly, I2C devices do not need any action,
either, because they are already different in their I2C address.

A similar problem is present for the pinctrl debugfs instance, but that
one is not addressed by this patch.

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12 10:47:23 +01:00
Kyle Yan 184f3448f6 pinctrl: qcom: Add sdm845 pinctrl driver
This adds the pinctrl definitions for the TLMM of SDM845.

Signed-off-by: Kyle Yan <kyan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-02-12 10:47:23 +01:00
Linus Torvalds ef991796be This is the bulk of pin control changes for the v4.16 kernel cycle:
Core changes:
 
 - After lengthy discussions and partly due to my ignorance, we have
   merged a patch making pinctrl_force_default() and pinctrl_force_sleep()
   reprogram the states into the hardware of any hogged pins, even
   if they are already in the desired state. This only apply to hogged
   pins since groups of pins owned by drivers need to be managed by
   each driver, lest they could not do things like runtime PM and
   put pins to sleeping state even if the system as a whole is not
   in sleep.
 
 New drivers:
 
 - New driver for the Microsemi Ocelot SoC. This is used in ethernet
   switches.
 
 - The X-Powers AXP209 GPIO driver was extended to also deal with pin
   control and moved over from the GPIO subsystem. This circuit is
   a mixed-mode integrated circuit which is part of AllWinner designs.
 
 - New subdriver for the Qualcomm MSM8998 SoC, core of a high end
   mobile devices (phones) chipset.
 
 - New subdriver for the ST Microelectronics STM32MP157 MPU and
   STM32F769 MCU from the STM32 family.
 
 - New subdriver for the MediaTek MT7622 SoC. This is used for routers,
   repeater, gateways and such network infrastructure.
 
 - New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC has
   multimedia features and target "smart devices", I guess in-car
   entertainment, in-flight entertainment, industrial control panels etc.
 
 General improvements:
 
 - Incremental improvements on the SH-PFC subdrivers for things like
   the CAN bus.
 
 - Enable the glitch filter on Baytrail GPIOs used for interrupts.
 
 - Proper handling of pins to GPIO ranges on the Semtec SX150X
 
 - An IRQ setup ordering fix on MCP23S08.
 
 - A good set of janitorial coding style fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJadGEKAAoJEEEQszewGV1zA4QQALs8edxhv4qV5vm50mTdrO3n
 QtRhJNb53j6MIKtjFnazMvh6MXRIP+08SyX9sDLi5AxINIVuyQh3mrcB6Zc9zN58
 +6jFFOIbfm5E8by4n3wnKm3F/WAbNBZph9eT2Rn3cDv9o9hQbyNJ50sQkQMCjd9X
 WGR353c3OL4zb3vU8t72G/RPYUY1w1SkG9bGzRuSif8LawDcN6v6MMo2XhZA6RqM
 3qYIG29vJ1n0weggUIBeSAJIzk4eMwcoWCbVWxhns5JGxw5VPES1zbSp1D+mbzRC
 01i5Pt/gD+cWN/Kk/zKIMo1OqLAl+uLr6hzepj6W+5wu9CcQz/BgvRx7HUqnqgyh
 S8cN4AOgWmW+T75pHypd1WVic3q0RCXkFY8jjHpCATDY+Z+js0lZRs3y4DBiJ2ys
 DMVBeumDINKqaZ6aLH6lVkm+SxXOUy143arQQIzi0/F7fAp68i+9ofIO8B5smEmd
 0S+3sT0sO5QXVgZJ0t0iGUUG5irXi8XtF5qvRmuFZUe0OLGgKX20oCdC0pH0WU4M
 OZO1Bvb8vmn1tddogO2WlHeg6amWdwxtDuBsLRO3YILLu3jwPjhNqNmErXzXEmWt
 TY9l2M1uQmoJibNpmTjOzSfj4OtUHMwkDrFRJHAcUPcKwdEy4MyzFL16ATnIwgY9
 AmyMLNWJd8Wazgc6BK6w
 =gLY/
 -----END PGP SIGNATURE-----

Merge tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.16 kernel cycle.
  Like with GPIO it is actually a bit calm this time.

  Core changes:

   - After lengthy discussions and partly due to my ignorance, we have
     merged a patch making pinctrl_force_default() and
     pinctrl_force_sleep() reprogram the states into the hardware of any
     hogged pins, even if they are already in the desired state.

     This only apply to hogged pins since groups of pins owned by
     drivers need to be managed by each driver, lest they could not do
     things like runtime PM and put pins to sleeping state even if the
     system as a whole is not in sleep.

  New drivers:

   - New driver for the Microsemi Ocelot SoC. This is used in ethernet
     switches.

   - The X-Powers AXP209 GPIO driver was extended to also deal with pin
     control and moved over from the GPIO subsystem. This circuit is a
     mixed-mode integrated circuit which is part of AllWinner designs.

   - New subdriver for the Qualcomm MSM8998 SoC, core of a high end
     mobile devices (phones) chipset.

   - New subdriver for the ST Microelectronics STM32MP157 MPU and
     STM32F769 MCU from the STM32 family.

   - New subdriver for the MediaTek MT7622 SoC. This is used for
     routers, repeater, gateways and such network infrastructure.

   - New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
     has multimedia features and target "smart devices", I guess in-car
     entertainment, in-flight entertainment, industrial control panels
     etc.

  General improvements:

   - Incremental improvements on the SH-PFC subdrivers for things like
     the CAN bus.

   - Enable the glitch filter on Baytrail GPIOs used for interrupts.

   - Proper handling of pins to GPIO ranges on the Semtec SX150X

   - An IRQ setup ordering fix on MCP23S08.

   - A good set of janitorial coding style fixes"

* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
  pinctrl: mcp23s08: fix irq setup order
  pinctrl: Forward declare struct device
  pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
  pinctrl: stm32: add STM32F769 MCU support
  pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
  pinctrl: sx150x: Register pinctrl before adding the gpiochip
  pinctrl: sx150x: Unregister the pinctrl on release
  pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
  pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
  pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
  pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
  pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
  pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
  pinctrl: uniphier: refactor drive strength get/set functions
  pinctrl: imx7ulp: constify struct imx_cfg_params_decode
  pinctrl: imx: constify struct imx_pinctrl_soc_info
  pinctrl: imx7d: simplify imx7d_pinctrl_probe
  pinctrl: imx: use struct imx_pinctrl_soc_info as a const
  pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
  pinctrl: qcom: Add msm8998 pinctrl driver
  ...
2018-02-02 14:22:53 -08:00
Linus Torvalds 9798f5178f The is the bulk of GPIO changes for the v4.16 kernel cycle.
Core changes:
 
 - Disallow open drain and open source flags to be set
   simultaneously. This doesn't make electrical sense, and would
   the hardware actually respond to this setting, the result
   would be short circuit.
 
 - ACPI GPIO has a new core infrastructure for handling quirks.
   The quirks are there to deal with broken ACPI tables centrally
   instead of pushing the work to individual drivers. In the world
   of BIOS writers, the ACPI tables are perfect. Until they find a
   mistake in it. When such a mistake is found, we can patch it
   with a quirk. It should never happen, the problem is that it
   happens. So we accomodate for it.
 
 - Several documentation updates.
 
 - Revert the patch setting up initial direction state from
   reading the device. This was causing bad things for drivers
   that can't read status on all its pins. It is only affecting
   debugfs information quality.
 
 - Label descriptors with the device name if no explicit label is
   passed in.
 
 - Pave the ground for transitioning SPI and regulators to use
   GPIO descriptors by implementing some quirks in the device tree
   GPIO parsing code.
 
 New drivers:
 
 - New driver for the Access PCIe IDIO 24 family.
 
 Other:
 
 - Major refactorings and improvements to the GPIO mockup driver
   used for test and verification.
 
 - Moved the AXP209 driver over to pin control since it gained a
   pin control back-end. These patches will appear (with the same
   hashes) in the pin control pull request as well.
 
 - Convert the onewire GPIO driver w1-gpio to use descriptors.
   This is merged here since the W1 maintainers send very few
   pull requests and he ACKed it.
 
 - Start to clean up driver headers using <linux/gpio.h> to just
   use <linux/gpio/driver.h> as appropriate.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJacIW6AAoJEEEQszewGV1z9b0P/jxWKaCAGFTTu/HZQ79RBAFq
 w33nIazzoh+88sN7A9xKexpr4ibOxiCvOwkTtrUBNaxGGy5fslj4+OY5BzunEfBK
 1vYxyEqtenvvZK03pOd6CSfHKV+vD5ngnVHGdtGzRvtmDDiSgtzqyEyUhQcXM+l7
 PrEh6qrd4TBZezlVR8kn5eqcmclkCBVSQCuLSq+ThMmCKRZuOdf1Im3D6eBzh1/N
 P81HdcglqbSsfUl1RcFiHs9Z+KcZOq83CNl2Ej1LePK2JBZbmkx9dR+WSJmV1u4P
 6wvzFcQDhfGEiiteg2BS5c+o6aAyShpuRNut+2MLre8icmdfpqUEqFotHbfQjW5y
 sqaejGsJ5aHcRBq7UUM+F9s1R0iN3tlafi3L0WEhl0Tn5huRQq3Uqcw6e5l+XrWd
 0h+b5PbKJZO/iqzRhSl+rhc0V2CFDJOCwvY+JX6356fvrcF0T6LhvKfDYtKU3Iyb
 HB0RG1OcYe228f96azvafCkFyBIYX9mqHBvOXpQQgrZQYXfN1rupLvpOhxC+Wbvn
 nsGE2bdD6HA1bytTbkxbL+QWP7faHf5YVcZpaN7UWbO3sOzL46fj8eHwHUim95Tr
 pR5kDZRhZd8+9SCNZ/ttpaEbis9MOqS/3Mlxrj4GXtfFFmR53hjFy2bG/Z7R2RB0
 MlSEJRc8iDIs+1j3D2RR
 =k5nL
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "The is the bulk of GPIO changes for the v4.16 kernel cycle. It is
  pretty calm this time around I think. I even got time to get to things
  like starting to clean up header includes.

  Core changes:

   - Disallow open drain and open source flags to be set simultaneously.
     This doesn't make electrical sense, and would the hardware actually
     respond to this setting, the result would be short circuit.

   - ACPI GPIO has a new core infrastructure for handling quirks. The
     quirks are there to deal with broken ACPI tables centrally instead
     of pushing the work to individual drivers. In the world of BIOS
     writers, the ACPI tables are perfect. Until they find a mistake in
     it. When such a mistake is found, we can patch it with a quirk. It
     should never happen, the problem is that it happens. So we
     accomodate for it.

   - Several documentation updates.

   - Revert the patch setting up initial direction state from reading
     the device. This was causing bad things for drivers that can't read
     status on all its pins. It is only affecting debugfs information
     quality.

   - Label descriptors with the device name if no explicit label is
     passed in.

   - Pave the ground for transitioning SPI and regulators to use GPIO
     descriptors by implementing some quirks in the device tree GPIO
     parsing code.

  New drivers:

   - New driver for the Access PCIe IDIO 24 family.

  Other:

   - Major refactorings and improvements to the GPIO mockup driver used
     for test and verification.

   - Moved the AXP209 driver over to pin control since it gained a pin
     control back-end. These patches will appear (with the same hashes)
     in the pin control pull request as well.

   - Convert the onewire GPIO driver w1-gpio to use descriptors. This is
     merged here since the W1 maintainers send very few pull requests
     and he ACKed it.

   - Start to clean up driver headers using <linux/gpio.h> to just use
     <linux/gpio/driver.h> as appropriate"

* tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (103 commits)
  gpio: Timestamp events in hardirq handler
  gpio: Fix kernel stack leak to userspace
  gpio: Fix a documentation spelling mistake
  gpio: Documentation update
  gpiolib: remove redundant initialization of pointer desc
  gpio: of: Fix NPE from OF flags
  gpio: stmpe: Delete an unnecessary variable initialisation in stmpe_gpio_probe()
  gpio: stmpe: Move an assignment in stmpe_gpio_probe()
  gpio: stmpe: Improve a size determination in stmpe_gpio_probe()
  gpio: stmpe: Use seq_putc() in stmpe_dbg_show()
  gpio: No NULL owner
  gpio: stmpe: i2c transfer are forbiden in atomic context
  gpio: davinci: Include proper header
  gpio: da905x: Include proper header
  gpio: cs5535: Include proper header
  gpio: crystalcove: Include proper header
  gpio: bt8xx: Include proper header
  gpio: bcm-kona: Include proper header
  gpio: arizona: Include proper header
  gpio: amd8111: Include proper header
  ...
2018-01-31 12:25:27 -08:00
Dmitry Mastykin 02e389e63e pinctrl: mcp23s08: fix irq setup order
When using mcp23s08 module with gpio-keys, often (50% of boots)
it fails to get irq numbers with message:
"gpio-keys keys: Unable to get irq number for GPIO 0, error -6".
Seems that irqs must be setup before devm_gpiochip_add_data().

Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-30 15:17:14 +01:00
Geert Uytterhoeven 470b73a384 pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-22 09:55:05 +01:00
Alexandre Torgue f90160fc95 pinctrl: stm32: add STM32F769 MCU support
This patch which adds STM32F769 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Patrice CHOTARD <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-22 09:28:08 +01:00
Peter Rosin b930151e5b pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
Without such a range, gpiolib fails with -EPROBE_DEFER, pending the
addition of the range. So, without a range, gpiolib will keep
deferring indefinitely.

Cc: stable@vger.kernel.org
Fixes: 9e80f9064e ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver")
Fixes: e10f72bf4b ("gpio: gpiolib: Generalise state persistence beyond sleep")
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-18 11:04:47 +01:00
Peter Rosin 1a1d39e1b8 pinctrl: sx150x: Register pinctrl before adding the gpiochip
Various gpiolib activity depend on the pinctrl to be up and kicking.
Therefore, register the pinctrl before adding a gpiochip.

Cc: stable@vger.kernel.org
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-18 11:04:43 +01:00
Peter Rosin 0657cb50b5 pinctrl: sx150x: Unregister the pinctrl on release
There is no matching call to pinctrl_unregister, so switch to the
managed devm_pinctrl_register to clean up properly when done.

Cc: stable@vger.kernel.org
Fixes: 9e80f9064e ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-18 11:04:30 +01:00
Wei Yongjun 119fcf47fd pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-18 08:51:32 +01:00
Markus Elfring 9d2fc7c370 pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-16 11:08:24 +01:00
Markus Elfring ffd10c2ec7 pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-16 11:07:18 +01:00
Markus Elfring 02c9d285ff pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-16 11:06:13 +01:00
Sean Wang 8b3d9cd48d pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
Make consistent error handling of all mtk_hw_get_value occurrences using
propagating error code from the internal instead of creating a new one.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:43:24 +01:00
Sean Wang 181cdac02c pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
commit d6ed935513 ("pinctrl: mediatek: add pinctrl driver for MT7622
SoC") leads to the following static checker warning:

drivers/pinctrl/mediatek/pinctrl-mt7622.c:1419 mtk_gpio_get()
error: uninitialized symbol 'value'.
1412  static int mtk_gpio_get(struct gpio_chip *chip, unsigned int gpio)
1413  {
1414          struct mtk_pinctrl *hw = dev_get_drvdata(chip->parent);
1415          int value;
1416
1417          mtk_hw_get_value(hw, gpio, PINCTRL_PIN_REG_DI, &value);
^^^^^^^^^^^^^^^^
1418
1419          return !!value;
1420  }

The appropriate error handling must be added to avoid the potential error
caused by uninitialized value being returned.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:42:12 +01:00
Masahiro Yamada fb36a7b07d pinctrl: uniphier: refactor drive strength get/set functions
There is code duplication between uniphier_conf_pin_drive_get() and
uniphier_conf_pin_drive_set().  Factor out the common code into
uniphier_conf_get_drvctrl_data().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:40:23 +01:00
Stefan Agner d6093367bc pinctrl: imx7ulp: constify struct imx_cfg_params_decode
The decode parameters are constant mark them const.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:29:40 +01:00
Stefan Agner 7c017687f8 pinctrl: imx: constify struct imx_pinctrl_soc_info
Now that imx_pinctrl_probe accepts const struct imx_pinctrl_soc_info
we can constify all declarations of struct imx_pinctrl_soc_info.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:29:37 +01:00
Stefan Agner 7372077542 pinctrl: imx7d: simplify imx7d_pinctrl_probe
Using of_device_get_match_data in imx7d_pinctrl_probe simplifies
the function. Also get rid of the void pointer cast since
imx_pinctrl_probe now accepts const struct imx_pinctrl_soc_info.

Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:29:32 +01:00
Stefan Agner f5843492ec pinctrl: imx: use struct imx_pinctrl_soc_info as a const
For some SoCs the struct imx_pinctrl_soc_info is passed through
of_device_id.data which is const. Most variables are already const
or otherwise not written. However, some fields are modified at
runtime. Move those fields to the dynamically allocated struct
imx_pinctrl.

Fixes: b3060044e4 ("pinctrl: freescale: imx7d: make of_device_ids const")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-11 10:29:18 +01:00
hao_zhang 32e21f084f pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
Pin function can not be match correctly when SUNXI_PIN describe with
mutiple variant and same function.

such as:
on pinctrl-sun4i-a10.c

SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
		SUNXI_FUNCTION(0x0, "gpio_in"),
		SUNXI_FUNCTION(0x1, "gpio_out"),
		SUNXI_FUNCTION_VARIANT(0x2, "pwm",    /* PWM0 */
			PINCTRL_SUN4I_A10 |
			PINCTRL_SUN7I_A20),
		SUNXI_FUNCTION_VARIANT(0x3, "pwm",    /* PWM0 */
			PINCTRL_SUN8I_R40)),

it would always match to the first variant function
(PINCTRL_SUN4I_A10, PINCTRL_SUN7I_A20)

so we should add variant compare on it.

Signed-off-by: hao_zhang <hao5781286@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-10 14:44:20 +01:00
Khan, Imran a3a093ae02 pinctrl: qcom: Add msm8998 pinctrl driver
Add initial pinctrl driver to support pin configuration with
pinctrl framework for msm8998.

Signed-off-by: Imran Khan <kimran@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
[bjorn: Consolidated function groups]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 15:30:20 +01:00
Markus Elfring 7c3012c855 pinctrl: mcp23s08: Combine two function calls into one in mcp23s08_dbg_show()
* Print a line break together with other data in a single function call.

* Adjust indentation.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 15:10:02 +01:00
Bai Ping ba33f4f42e pinctrl: imx6ul: add IOMUXC SNVS pinctrl driver for i.MX 6ULL
On i.MX 6ULL, the BOOT_MODEx and TAMPERx pin MUX and CTRL registers
are available in a separate IOMUXC_SNVS module. Add support for the
IOMUXC_SNVS module to the i.MX 6UL pinctrl driver.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 14:59:17 +01:00
Alexandre Belloni ce8dc09433 pinctrl: Add Microsemi Ocelot SoC driver
The Microsemi Ocelot SoC has a few pins that can be used as GPIOs or take
multiple other functions. Add a driver for the pinmuxing and the GPIOs.

There is currently no support for interrupts.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 14:54:59 +01:00
Masahiro Yamada b67ecdec45 pinctrl: remove redundant mux_setting clear in pinmux_disable_setting()
desc->mux_setting is set to NULL in pin_free() called just below.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-09 14:48:34 +01:00
Linus Walleij 55b6986ca1 pinctrl: sh-pfc: Updates for v4.16 (take two)
- Add PWM pin groups on various R-Car Gen2 and RZ/G1 SoCs,
   - Add missing I2C5 pin groups on R-Car E2 and RZ/G1E,
   - Add SATA pin groups on R-Car H3 ES2.0.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaT1M+AAoJEEgEtLw/Ve77BkwP/jR3qNvbAW6Ur5bQvl5rVJcc
 +OoSZU0ULXP6kwk0KxMcddpAWyCYKsy+lbQaIAnjJlZa/JCr4Am7A42OB/lTfDo1
 EQmt9aWA8RAGvsLOZwsfP/FCw8o3BpYOjS1EhoXi+Y91VHfSehCrZiPRs/2AkVZb
 cWntYOw5EJXwKcAH7gL4dhE93vSVyKTs8uimdZ+NlNDT3Z42vUckdGXqPjKYT/OB
 wNFk/u/bZ5iOR9b7K8UQFZ255Yzp8rIfFUsXUBUGBgN0DKjsbppYd2qV6JZoGC78
 LW2kewGXLHk1zuSnveY+AbEQKz/hKlPIviW0QoQ9nJwsMthTUf/OOZFTPuryuNLc
 jtUzlqNfEHS/fbLqii8ey3VourrI3vLGZ8jaXT0k33CK9cx8bY33g103oUpUBk0w
 HXy+I9DrvE74aEf2oqW+oHOjIRp4RPsVVtgbvw2wdDcroHtNcxYLjeEaujEjDNxm
 9yslzlNSt9R9O1J/c4gPfM90laOOr8By6nA98igQykDlGEyzLZnEsqD7pmMVOhYx
 Nh6mpw4J9IRy/6lHoMc9SWPeodEvDer7XDZI69gU1jNkanTiWb8ZPn498UP9p9WH
 ytN3yxaqqAFb60oQhKw1b5a9kCjbmzX+J4qirffIcw4XT9R9CO20IGwUeyPagkVs
 dSrdEmHEfwnufmjyMC8J
 =EJKS
 -----END PGP SIGNATURE-----

Merge tag 'sh-pfc-for-v4.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.16 (take two)

  - Add PWM pin groups on various R-Car Gen2 and RZ/G1 SoCs,
  - Add missing I2C5 pin groups on R-Car E2 and RZ/G1E,
  - Add SATA pin groups on R-Car H3 ES2.0.
2018-01-08 08:17:10 +01:00
Julia Lawall 924f5494da pinctrl: armada-37xx: account for const type of of_device_id.data
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.

Done using Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-08 08:15:48 +01:00
Julia Lawall 9b8ee3c0f6 pinctrl: axp209: account for const type of of_device_id.data
The return value of of_device_get_match_data has type const void *.
The desc field of the pctl structure also has a const type, so there
is no need for the const-discarding cast between them.

Done using Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-08 08:15:47 +01:00
Julia Lawall 8b74c7d3e3 pinctrl: at91-pio4: account for const type of of_device_id.data
This driver creates a const structure that it stores in the data field
of an of_device_id array.

Adding const to the declaration of the location that receives the
const value from the data field ensures that the compiler will
continue to check that the value is not modified.  Furthermore, the
const-discarding cast on the extraction from the data field is no
longer needed.

Done using Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-08 08:15:47 +01:00
Hans de Goede 9291c65b01 pinctrl: baytrail: Enable glitch filter for GPIOs used as interrupts
On some systems, some PCB traces attached to GpioInts are routed in such
a way that they pick up enough interference to constantly (many times per
second) trigger.

Enabling glitch-filtering fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-08 08:15:46 +01:00
Markus Elfring 659e7142bd pinctrl: vt8500: Delete an error message for a failed memory allocation in five functions
Omit an extra message for a memory allocation failure in these functions.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-08 08:15:46 +01:00
Markus Elfring b18b2e7759 pinctrl: tegra: Delete two error messages for a failed memory allocation in tegra_pinctrl_probe()
Omit extra messages for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:55 +01:00
Markus Elfring 51d7a036a6 pinctrl: spear: Delete an error message for a failed memory allocation in spear_pinctrl_probe()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:55 +01:00
Markus Elfring b5623acb8d pinctrl/spear/plgpio: Delete two error messages for a failed memory allocation in plgpio_probe()
Omit extra messages for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:54 +01:00
Krzysztof Kozlowski 221173a3fc pinctrl: samsung: Add SPDX license identifiers
Replace GPL license statements with SPDX GPL-2.0+ license identifiers.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:54 +01:00
Markus Elfring e423f0ceef pinctrl: xway: Delete two error messages for a failed memory allocation in pinmux_xway_probe()
Omit extra messages for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:53 +01:00
Markus Elfring 86f75c65ff pinctrl: utils: Delete an error message for a failed memory allocation in pinctrl_utils_add_map_configs()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:53 +01:00
Markus Elfring 405e64a1cd pinctrl: tz1090-pdc: Delete an error message for a failed memory allocation in two functions
Omit an extra message for a memory allocation failure in these functions.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:52 +01:00
Markus Elfring 8c017679ab pinctrl: tz1090: Delete an error message for a failed memory allocation in two functions
Omit an extra message for a memory allocation failure in these functions.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:52 +01:00
Markus Elfring 7598160d7d pinctrl: single: Delete an unnecessary return statement in pcs_irq_chain_handler()
The script "checkpatch.pl" pointed information out like the following.

WARNING: void function return statements are not generally useful

Thus remove such a statement in the affected function.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:51 +01:00
Markus Elfring a14aa2716b pinctrl: single: Delete an error message for a failed memory allocation in pcs_probe()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:51 +01:00
Markus Elfring 85dc397a24 pinctrl: rockchip: Fix a typo in four comment lines
Adjust words in these descriptions.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:51 +01:00
Markus Elfring 283b7ac92b pinctrl: rockchip: Improve a size determination in rockchip_pinctrl_probe()
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:50 +01:00
Markus Elfring 98c8ee73fe pinctrl: rockchip: Delete error messages for a failed memory allocation in two functions
Omit extra messages for a memory allocation failure in these functions.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:50 +01:00
Markus Elfring 5896c8d7c8 pinctrl: palmas: Delete an error message for a failed memory allocation in palmas_pinctrl_probe()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:49 +01:00
Markus Elfring 3da941b048 pinctrl: at91: Delete an error message for a failed memory allocation in at91_pinctrl_mux_mask()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-01-03 08:46:49 +01:00
Thomas Gleixner 702cb0a028 genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.

No functional change.

Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
2017-12-29 21:13:04 +01:00
Icenowy Zheng e210a0a948 pinctrl: sunxi: fix a typo when merging A20 support to A10 driver
When merging A20 pinctrl support to A10 pinctrl driver, the I2C function
of PI3 is wrongly written as "i2c3" (it should be "i2c4").

Fix this typo.

Fixes: cad4e209c1 ("pinctrl: sunxi: add support of R40 to A10 pinctrl driver")
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-28 15:06:01 +01:00
Markus Elfring 203f4b0651 pinctrl: msm: Delete an error message for a failed memory allocation in msm_pinctrl_probe()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-28 13:41:02 +01:00
Linus Walleij bd8ed930af Revert "pinctrl: qcom: disable GPIO groups with no pins"
This reverts commit 93ebe8636b.

After discussion and review of the v11 patchset, a new approach
was found so that this patch is not needed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-28 13:32:53 +01:00
Andrew Lunn 39c3fd5895 kernel/irq: Extend lockdep class for request mutex
The IRQ code already has support for lockdep class for the lock mutex
in an interrupt descriptor. Extend this to add a second class for the
request mutex in the descriptor. Not having a class is resulting in
false positive splats in some code paths.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: linus.walleij@linaro.org
Cc: grygorii.strashko@ti.com
Cc: f.fainelli@gmail.com
Link: https://lkml.kernel.org/r/1512234664-21555-1-git-send-email-andrew@lunn.ch
2017-12-28 12:26:35 +01:00
Timur Tabi 93ebe8636b pinctrl: qcom: disable GPIO groups with no pins
pinctrl-msm only accepts an array of GPIOs from 0 to n-1, and it expects
each group to support have only one pin (npins == 1).

We can support "sparse" GPIO maps if we allow for some groups to have zero
pins (npins == 0).  These pins are "hidden" from the rest of the driver
and gpiolib.

Access to unavailable GPIOs is blocked via a request callback.  If the
requested GPIO is unavailable, -EACCES is returned, which prevents
further access to that GPIO.

Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-21 13:04:35 +01:00
Markus Elfring ce8b8d70d4 pinctrl: adi2: Improve a size determination in two functions
Replace the specification of data structures by variable references
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-21 10:22:41 +01:00
Markus Elfring 419517f15d pinctrl: adi2: Delete an error message for a failed memory allocation in two functions
Omit an extra message for a memory allocation failure in these functions.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-21 10:21:56 +01:00
Markus Elfring cb1a42d5fa pinctrl/nomadik/abx500: Improve a size determination in abx500_gpio_probe()
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-21 10:20:29 +01:00
Markus Elfring 8931dc0804 pinctrl/nomadik/abx500: Delete an error message for a failed memory allocation in abx500_gpio_probe()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-21 10:19:26 +01:00
Wolfram Sang 297e5b2b7a pinctrl: sh-pfc: r8a7795: Add SATA pins, groups, and functions
Tested with a Salvator-XS and H3 ES2.0.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-21 10:08:23 +01:00
Markus Elfring bca50ce005 pinctrl: mvebu: Delete an error message for a failed memory allocation in mvebu_pinctrl_probe()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 13:20:27 +01:00
Tony Lindgren c2584927b7 pinctrl: single: Remove invalid message
Pinctrl single should just show how many pins were found, the physical
address is already in the dev information. So let's remove the wrong
information that claims to show the physical address but really prints
a virtual address that is now hashed.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 12:38:46 +01:00
Linus Walleij 723dd2f0de pinctrl: sh-pfc: Updates for v4.16
- Add CAN pin groups on RZ/G1E,
   - Add CAN and CAN FD pin groups on R-Car H3 ES2.0, and R-Car D3,
   - Add support for the new R-Car V3M SoC,
   - Add support for I2C on R-Car D3,
   - Small fixes and cleanups.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaM5QbAAoJEEgEtLw/Ve77DL0QAK5qKY/9Jt9PASqIvEJMsc5U
 Ns8ULXaynLSvOLHWNCFN0MD53gnKsQVOFMynsf1NWJ5j2fqCCu5nkrxoZKTTxMWs
 1TJGXBrCqQLzQspUXxdjFwJHIOeXCDQllw5Xsdq4MbzmlDRr+G9jj7CxLK5pjk1B
 jUZ+cfDBwuSWlDymrwcEAREBQtg7HYBlkt1zyFXPJYu5R/iGdE1ih39yBqTPka1/
 ua+d2FdGOUeOXoqqAkkJZ9+8YsITAoU+YoriKgf2I/vLiovBCBSdfenJZ5He+Hth
 7EWaIiK1Y/zdwadUtzC6/FGckkn4kj6+t5koLrXaSXce/TO4uWN6iIAiWATd26CY
 sxv1+likNAN5rGXtowXiyyOo26bZ/nFchgT4JC8FZdG0DeseOAFYE8pn8TKvDdSZ
 RTPmo6r/CiFsyn3oAzOjSMbafEvXJBZX/QQDgsS1orboWAbi8YtswacIPc/GGBhr
 iCc28erUks2fSq4+3W64Q+s/061I7NiES13ry9o3srfjWb45PEdjO+FUMN8chazt
 sNrWWrRB6HEs9N5/jGA6ZRPnbZnJnl8d1sxY/Tpj32To0kDWn3CVlGwLZDDaRIJf
 Zs/q8i/2D97RyiXtTtKacO2fZpHWQl+9kDKXOEjVcLZh5utkKM+L2cBSHoG5cCRn
 XsPp6HLHI4BdJnap4+La
 =dwjl
 -----END PGP SIGNATURE-----

Merge tag 'sh-pfc-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v4.16

  - Add CAN pin groups on RZ/G1E,
  - Add CAN and CAN FD pin groups on R-Car H3 ES2.0, and R-Car D3,
  - Add support for the new R-Car V3M SoC,
  - Add support for I2C on R-Car D3,
  - Small fixes and cleanups.
2017-12-20 10:37:46 +01:00
Quentin Schulz 971f1b38f9 pinctrl: axp209: add missing Kconfig dependencies
This fixes some compilation issues.

GENERIC_PINCONF and OF at least for pinconf_generic_dt_*, PINMUX at
least for pinmux_ops and GPIOLIB for at least gpio_chip.

Fixes: 23f75d7dfa ("pinctrl: axp209: add pinctrl features")

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 09:13:14 +01:00
Quentin Schulz a049815229 pinctrl: axp209: dereference pointer after it's been set
The number of GPIOs is gotten from a field within the structure
referenced in the of_device.data but it was actually read before it was
retrieved, thus it was dereferencing a null pointer.

Set the number of GPIOs after retrieving of_device.data.

Fixes: e1190083b8 ("pinctrl: axp209: add support for AXP813 GPIOs")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Tested-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 09:06:29 +01:00
Brian Norris 5c9d8c4f6b pinctrl: rockchip: enable clock when reading pin direction register
We generally leave the GPIO clock disabled, unless an interrupt is
requested or we're accessing IO registers. We forgot to do this for the
->get_direction() callback, which means we can sometimes [1] get
incorrect results [2] from, e.g., /sys/kernel/debug/gpio.

Enable the clock, so we get the right results!

[1] Sometimes, because many systems have 1 or mor interrupt requested on
each GPIO bank, so they always leave their clock on.

[2] Incorrect, meaning the register returns 0, and so we interpret that
as "input".

Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 09:00:13 +01:00
Sean Wang d6ed935513 pinctrl: mediatek: add pinctrl driver for MT7622 SoC
Add support for pinctrl on MT7622 SoC. The IO core found on the SoC has
the registers for pinctrl, pinconf and gpio mixed up in the same register
range. However, the IO core for the MT7622 SoC is completely distinct from
anyone of previous MediaTek SoCs which already had support, such as
the hardware internal, register address map and register detailed
definition for each pin.

Therefore, instead, the driver is being newly implemented by reusing
generic methods provided from the core layer with GENERIC_PINCONF,
GENERIC_PINCTRL_GROUPS, and GENERIC_PINMUX_FUNCTIONS for the sake of code
simplicity and rid of superfluous code. Where the function of pins
determined by groups is utilized in this driver which can help developers
less confused with what combinations of pins effective on the SoC and even
reducing the mistakes during the integration of those relevant boards.

As the gpio_chip handling is also only a few lines, the driver also
implements the gpio functionality directly through GPIOLIB.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 08:49:41 +01:00
Sean Wang e3fd24a574 pinctrl: mediatek: cleanup for placing all drivers under the menu
Since lots of MediaTek drivers had been added, it seems slightly better
for that adding cleanup for placing MediaTek pinctrl drivers under the
independent menu as other kinds of drivers usually was done.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 08:47:56 +01:00
Ludovic Barre 4ef4cc13ea pinctrl: stm32: Add STM32MP157 MPU support
This driver consists of 2 controllers due to a hole in mapping:
-1 controller for GPIO bankA to K.
-1 controller for GPIO bankZ.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 08:36:22 +01:00
Florian Fainelli 981ed1bfbc pinctrl: Really force states during suspend/resume
In case a platform only defaults a "default" set of pins, but not a
"sleep" set of pins, and this particular platform suspends and resumes
in a way that the pin states are not preserved by the hardware, when we
resume, we would call pinctrl_single_resume() -> pinctrl_force_default()
-> pinctrl_select_state() and the first thing we do is check that the
pins state is the same as before, and do nothing.

In order to fix this, decouple the actual state change from
pinctrl_select_state() and move it pinctrl_commit_state(), while keeping
the p->state == state check in pinctrl_select_state() not to change the
caller assumptions. pinctrl_force_sleep() and pinctrl_force_default()
are updated to bypass the state check by calling pinctrl_commit_state().

[Linus Walleij]
The forced pin control states are currently only used in some pin
controller drivers that grab their own reference to their own pins.
This is equal to the pin control hogs: pins taken by pin control
devices since there are no corresponding device in the Linux device
hierarchy, such as memory controller lines or unused GPIO lines,
or GPIO lines that are used orthogonally from the GPIO subsystem
but pincontrol-wise managed as hogs (non-strict mode, allowing
simultaneous use by GPIO and pin control). For this case forcing
the state from the drivers' suspend()/resume() callbacks makes
sense and should semantically match the name of the function.

Fixes: 6e5e959dde ("pinctrl: API changes to support multiple states per device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-20 08:24:13 +01:00
Fabrizio Castro 21047d5736 pinctrl: sh-pfc: r8a7791: Add tpu groups and function
This patch adds tpu groups and function to r8a7743/r8a7791/r8a7793.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-19 11:04:49 +01:00
Biju Das 0d68d46035 pinctrl: sh-pfc: r8a7794: Add i2c5 pin groups and function
Add i2c5 pin groups and function to r8a7745 PFC driver.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-19 11:04:48 +01:00
Fabrizio Castro 64dbebc87d pinctrl: sh-pfc: r8a7794: Add tpu groups and function
This patch adds tpu groups and function to r8a7745/r8a7794.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-19 10:20:05 +01:00
Fabrizio Castro 20796a2caf pinctrl: sh-pfc: r8a7794: Add PWM[0123456] support
This patch adds PFC PWM[0123456] pin groups and functions, enabling
PWM on the r8a7794 and r8a7745.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-19 10:19:47 +01:00
Yixun Lan d72ebbcc44 pinctrl: meson-axg: adjust spicc pin naming
According to datasheet, we should use numbers for the pin naming
instead of letters. The patch here try to fix this to keep
the consistency.

This patch should not bring any functional change.

Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-13 00:52:49 +01:00
Mika Westerberg d2b3c35359 pinctrl: cherryview: Mask all interrupts on Intel_Strago based systems
Guenter Roeck reported an interrupt storm on a prototype system which is
based on Cyan Chromebook. The root cause turned out to be a incorrectly
configured pin that triggers spurious interrupts. This will be fixed in
coreboot but currently we need to prevent the interrupt storm from
happening by masking all interrupts (but not GPEs) on those systems.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Fixes: bcb48cca23 ("pinctrl: cherryview: Do not mask all interrupts in probe")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-12 09:51:38 +01:00
Linus Walleij c6e40f9639 Merge branch 'ib-move-axp209' of /home/linus/linux-gpio into devel 2017-12-07 10:10:24 +01:00
Quentin Schulz e1190083b8 pinctrl: axp209: add support for AXP813 GPIOs
The AXP813 has only two GPIOs. GPIO0 can either be used as a GPIO, an
LDO regulator or an ADC. GPIO1 can be used either as a GPIO or an LDO
regulator.

Moreover, the status bit of the GPIOs when in input mode is not offset
by 4 unlike the AXP209.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 10:08:12 +01:00
Quentin Schulz a0a4b4c242 pinctrl: axp209: add programmable ADC muxing value
To prepare for patches that will add support for a new PMIC that has a
different GPIO adc muxing value, add an adc_mux within axp20x_pctl
structure and use it.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 10:07:45 +01:00
Quentin Schulz 48e706fbc5 pinctrl: axp209: add programmable gpio_status_offset
To prepare for patches that will add support for a new PMIC that has a
different GPIO input status register, add a gpio_status_offset within
axp20x_pctl structure and use it.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 10:07:19 +01:00
Quentin Schulz d242e60c7d pinctrl: axp209: rename everything from gpio to pctl
This driver used to do only GPIO features of the GPIOs in X-Powers
AXP20X. Now that we have migrated everything to the pinctrl subsystem
and added pinctrl features, rename everything related to pinctrl from
gpio to pctl to ease the understanding of differences between GPIO
and pinctrl features.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 10:06:57 +01:00
Quentin Schulz 23f75d7dfa pinctrl: axp209: add pinctrl features
The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.

This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 10:05:58 +01:00
Quentin Schulz 449317a8b4 pinctrl: move gpio-axp209 to pinctrl
To prepare the driver for the upcoming pinctrl features, move the GPIO
driver AXP209 from GPIO to pinctrl subsystem.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 10:05:30 +01:00
Colin Ian King 33b6cb58cb pinctrl: intel: ensure error return ret is initialized
In the (unlikely) event that community->ngpps is zero, or if every
gpp->gpio_base is less than zero, then an ininitialized value in
ret is returned by function intel_gpio_add_pin_ranges. Fix this by
ensuring ret is initialized to zero.  It's a moot point, but I think
it is worthwhile ensuring this corner case is fixed.

Detected by CoverityScan, CID#1462415 ("Uninitialized scalar variable")

Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 09:59:39 +01:00
Linus Walleij ad63da85f4 pinctrl: gemini: Support drive strength setting
The Gemini pin controller can set drive strength for a few
select groups of pins (not individually). Implement this
for GMAC0 and 1 (ethernet ports), IDE and PCI.

Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-07 09:59:26 +01:00
Ulrich Hecht 527890f728 pinctrl: sh-pfc: r8a77995: Add CAN FD support
This patch adds CAN FD[0-1] pinmux support to the r8a77995 SoC.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:56 +01:00
Ulrich Hecht c45985d359 pinctrl: sh-pfc: r8a77995: Add CAN support
This patch adds CAN[0-1] pinmux support to the r8a77995 SoC.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:55 +01:00
Takeshi Kihara 0f4713d71f pinctrl: sh-pfc: r8a7796: Rename RTS{0,1,3,4}# pin function definitions
This patch renames the pin function macro definitions of the GPSR5 and
IPSR{0,3,5,6,12} registers value for the RTS{0,1,3,4}# pin.

This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:55 +01:00
Takeshi Kihara 8714a9c1bd pinctrl: sh-pfc: r8a7795: Rename RTS{0,1,3,4}# pin function definitions
This patch renames the pin function macro definitions of the GPSR and
IPSR registers value for the RTS{0,1,3,4}# pin.

This is a correction because GPSR and IPSR register specification for
R8A7795 ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual
Rev.0.54E.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Drop remaining "_TANS" from comments]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:54 +01:00
Takeshi Kihara fbd81e345c pinctrl: sh-pfc: r8a7796: Fix to delete A20..A25 pins function definitions
This patch fixes the macro definitions of A20..A25 pins function deleted.

This is a correction because IPSR register specification for R8A7796 SoC
was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.

Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:53 +01:00
Takeshi Kihara 7716c51b5e pinctrl: sh-pfc: r8a7795: Fix to delete A20..A25 pins function definitions
This patch fixes the macro definitions of A20..A25 pins function deleted.

This is a correction because IPSR register specification for R8A7795 ES2.0
SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.

Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:53 +01:00
Takeshi Kihara b16cd900de pinctrl: sh-pfc: r8a7795-es1: Fix MOD_SEL1 bit[25:24] to 0x3 when using STP_ISEN_1_D
This patch fixes the implementation incorrect of MOD_SEL1 bit[25:24]
value when STP_ISEN_1_D pin function is selected for IPSR16 bit[27:24].

This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7795 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E.

Fixes: 0b0ffc96db ("pinctrl: sh-pfc: Initial R8A7795 PFC support)
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:52 +01:00
Takeshi Kihara 82d2de5a4f pinctrl: sh-pfc: r8a7795: Add GP-1-28 port pin support
This patch supports GP-1-28 port pin of R8A7795 ES2.0 SoC added in
Rev.0.54E of the R-Car Gen3 Hardware User's Manual or later version.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Update forgotten PUEN2 entry]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:51 +01:00
Ulrich Hecht af4b609e6f pinctrl: sh-pfc: r8a77995: Add missing pins SCL0 and SDA0 to pinmux data
Required for I2C0 operation.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:51 +01:00
Fabrizio Castro 57eec02cae pinctrl: sh-pfc: r8a7791: Add can_clk function
This patch adds can_clk function to r8a7743/r8a7791 which is cleaner,
and allows for independent configuration.
We keep the can_clk* pins definitions from within can0_groups and
can1_groups for uniformity and backwards compatibility.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:50 +01:00
Fabrizio Castro 7c4a390647 pinctrl: sh-pfc: r8a7794: Add can_clk function
This patch adds can_clk function to r8a7745/r8a7794 which is cleaner,
and allows for independent configuration.
We keep the can_clk* pins definitions from within can0_groups and
can1_groups for uniformity and backwards compatibility.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:49 +01:00
Sergei Shtylyov b92ac66a18 pinctrl: sh-pfc: Add R8A77970 PFC support
Add the PFC support for the R8A77970 SoC including pin groups for some
on-chip devices such as CAN-FD, [H]SCIF, I2C, INTC-EX, MMC, MSIOF, PWM,
VIN...

Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Drop EtherAVB for now]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2017-12-05 14:14:39 +01:00
Benjamin Gaignard e7c0e2f372 pinctrl: stm32: Fix copyright
Uniformize STMicroelectronics copyrights header
Add SPDX identifier

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-02 16:23:08 +01:00
Mika Westerberg f5a26acf01 pinctrl: intel: Initialize GPIO properly when used through irqchip
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.

When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.

Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.

Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-and-tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-12-02 13:11:04 +01:00
Andre Przywara 07c43a382d pinctrl: sunxi: Disable strict mode for H5 driver
All of the H5 boards in the kernel reference the MMC0 CD pin twice in
their DT, so strict mode will make the MMC driver fail to load.
To keep existing DTs working, disable strict mode in the H5 driver.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Chris Obbard <obbardc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 16:50:43 +01:00
Andre Przywara 7c5c2c2d18 pinctrl: sunxi: Fix A64 UART mux value
To use pin PF4 as the RX signal of UART0, we have to write 0b011 into
the respective pin controller register.
Fix the wrong value we had in our table so far.

Fixes: 96851d391d ("drivers: pinctrl: add driver for Allwinner A64 SoC")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 16:48:54 +01:00
Andre Przywara 6ad4cc8d1a pinctrl: sunxi: Fix A80 interrupt pin bank
On the A80 the pins on port B can trigger interrupts, and those are
assigned to the second interrupt bank.
Having two pins assigned to the same interrupt bank/pin combination does
not look healthy (instead more like a copy&paste bug from pins PA14-PA16),
so fix the interrupt bank for pins PB14-PB16, which is actually 1.

I don't have any A80 board, so could not test this.

Fixes: d5e9fb31ba ("pinctrl: sunxi: Add A80 pinctrl muxing options")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 16:47:37 +01:00
Linus Walleij 793b918404 pinctrl: gemini: Fix usage of 3512 groups
The pin config lookup function was still hardcoding the
3516 pin set, which is obviously wrong. Use the pointer
in the state container.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 15:36:34 +01:00
Jesse Chan 0b9335cbd3 pinctrl: pxa: pxa2xx: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/pinctrl/pxa/pinctrl-pxa2xx.o
see include/linux/module.h for more information

This adds the license as "GPL v2", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.

Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 14:42:04 +01:00
Linus Walleij 9c957fcecb pinctrl: gemini: Add two missing GPIO groups
The 3512 has two more GPIO groups on GPIO area 0, so let's
make it possible to combine these with the function.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 14:35:01 +01:00
Xingyu Chen 83c566806a pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC
Add new pinctrl driver for Amlogic's Meson-AXG SoC.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 14:29:38 +01:00
Xingyu Chen 0fabe43f3f pinctrl: meson-axg: Introduce a pinctrl pinmux ops for Meson-AXG SoC
The pin controller has been updated in the Amlogic Meson AXG series,
which use continuous 4-bit register to select function for each pin.
In order to support this, a new pinmux operations "meson_axg_pmx_ops"
has been added.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-30 14:28:16 +01:00
Gregory CLEMENT 6702abb3bf pinctrl: armada-37xx: Fix direction_output() callback behavior
The direction_output callback of the gpio_chip structure is supposed to
set the output direction but also to set the value of the gpio. For the
armada-37xx driver this callback acted as the gpio_set_direction callback
for the pinctrl.

This patch fixes the behavior of the direction_output callback by also
applying the value received as parameter.

Cc: stable@vger.kernel.org
Fixes: 5715092a45 ("pinctrl: armada-37xx: Add gpio support")
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-29 14:09:23 +01:00
Markus Elfring 7f6f50dfb5 pinctrl: mcp23s08: Improve unlocking of a mutex in mcp23s08_irq()
* Add a jump target so that a call of the function "mutex_unlock" is stored
  only twice in this function implementation.

* Replace five calls by goto statements.

* Adjust five condition checks.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-29 13:51:10 +01:00