dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fd ("usb: dwc3: exynos: add nop transceiver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
that message is informing that the clock is missing.
However, that's a valid condition for some setups; driver
even ignores the error and continues just fine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller on Exynos7 SoC has separate control for
AXI UpScaler which connects DWC3 DRD controller to AXI bus.
Get the gate clock for the same to control it across power
cycles.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller on Exynos SoC series have separate control for
suspend clock which replaces pipe3_rx_pclk as clock source to
a small part of DWC3 core that operates when SS PHY is in its
lowest power state (P3) in states SS.disabled and U3.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to keep one local variable for clock, and
then assign the same to 'clk' member of dwc3_exynos.
Just cleaning it up.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
First usage of ret variable will re-write initial value. Thus, there is no need
to initialize it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Facilitate getting required 3.3V and 1.0V VDD supply for
DWC3 controller on Exynos.
With patches for regulators' nodes merged in 3.15:
c8c253f ARM: dts: Add regulator entries to smdk5420
275dcd2 ARM: dts: add max77686 pmic node for smdk5250,
certain perripherals will now need to ensure that,
they request VDD regulators in their drivers, and enable
them so as to make them working.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The reset_gpio member of the usb_phy_gen_xceiv_platform_data
structure needs the have negative value or phy-generic's
probe will fail unless DT is used. 0 is a valid gpio number.
This fixes an issue where phy-generic fails to probe with
message: "usb_phy_gen_xceiv.0: Error requesting RESET GPIO 0".
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "nop" driver isn't a do-nothing-stub but supports a couple functions
like clock on/off or is able to use a voltage regulator. This patch
simply renames the driver to "generic" since it is easy possible to
extend it by a simple function istead of writing a complete driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.
Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Many USB host drivers contain code such as:
if (!pdev->dev.dma_mask)
pdev->dev.dma_mask = &tegra_ehci_dma_mask;
... where tegra_ehci_dma_mask is a global. I suspect this code originated
in commit 4a53f4e "USB: ehci-tegra: add probing through device tree" and
was simply copied everywhere else.
This works fine when the code is built-in, but can cause a crash when the
code is in a module. The first module load sets up the dma_mask pointer,
but if the module is removed and re-inserted, the value is now non-NULL,
and hence is not updated to point at the new location, and hence points
at a stale location within the previous module load address, which in
turn causes a crash if the pointer is de-referenced.
The simplest way of solving this seems to be to copy the code from
ehci-platform.c, which uses the coherent_dma_mask as the target for the
dma_mask pointer.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs
are removed.
drivers/usb/dwc3/core.c:682:12: warning: 'dwc3_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/core.c:709:12: warning: 'dwc3_resume' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-omap.c:430:12: warning: 'dwc3_omap_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-omap.c:440:12: warning: 'dwc3_omap_resume' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-exynos.c:185:12: warning: 'dwc3_exynos_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc3/dwc3-exynos.c:194:12: warning: 'dwc3_exynos_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
CC: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used of_platform_populate() to create dwc3 core platform_device
from device tree data. Additionally some cleanup is also done.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds suspend and resume callbacks to exynos dwc3 driver as part of
power management support.
This change does gating of dwc3 clock during suspend/resume cycles.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Vikas C Sajjan <vikas.sajjan@linaro.org>
CC: Doug Anderson <dianders@chromium.org>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
[ balbi@ti.com : refreshed to current linus/master ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Multiple dwc3 probe calls try to allocate no_op_xceive platform
device. Having static IDs for these will throw sysfs error -EEXIST.
Changing these static platform device IDs to AUTO to enable
multiple dwc3 controller support on a SoC.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using specific chip in compatible strings. Newer SOCs can claim
device by using older string in the compatible list.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are removing plat data which was used till now to init and
exit phy. We no longer need this since dwc3-core takes care of
initializing and shutting-down the phy using usb_phy_init()
and usb_phy_shutdown().
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support to parse probe data for
dwc3-exynos driver using device tree.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The lockless implementation of the unique id is quite impressive (:P)
but dirver's core can handle it, we can remove it and make our code a
little smaller.
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We will be adding support for transceivers on
dwc3 driver but not all boards have controllable
transceivers.
For those which don't provide controllable transceivers
we will register nop transceivers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds Exynos Specific Glue layer to support USB peripherals
on Samsung Exynos5 chips.
[ balbi@ti.com : prevent compilation of Exynos glue layer
on platforms which don't provide clk API implementation ]
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Steinar H. Gunderson