Additional debugging to show xHC USBSTS register when stop endpoint
command watchdog triggers and host is assumed dead.
useful to know the current status before the controller is stopped by
the xhci driver and everything is released and freed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't show the same error message for transaction errors and split
transaction errors. It's very confusing while debugging.
Transaction errors are often due to electrical interference.
Split transaction errors are about xHC not being able to
schedule start and complete split transactions needed to address
low- and full-speed devices behind high-speed hubs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case there are multiple Marvell EHCI blocks in system, we need a
different bus name for each one. Otherwise debugfs gets mildly upset about
a directory name in usb/ehci:
debugfs: Directory 'mv ehci' with parent 'ehci' already present!
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out the undocumented and reserved bits of port status/control
register of the root port need to be set to use the HCI in HSIC mode.
Typically the firmware does this, but that is not always good enough,
because the bits get lost if the HSIC clock is disabled (e.g. when
ehci-mv is build as a module).
This supplements commit 7b104f890a ("USB: EHCI: ehci-mv: add HSIC
support").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for
VirtualLink DP mode and vdo=0x3 for NVIDIA test mode. NVIDIA
test device FTB (Function Test Board) reports altmode list with
vdo=0x3 first and then vdo=0x1. The list is:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x3
0x955 0x1
Current logic to assign mode value is based on order
in altmode list. This causes a mismatch of CON and SOP altmodes
since NVIDIA GPU connector has order of vdo=0x1 first and then
vdo=0x3. Fixing this by changing the order of vdo values
reported by NVIDIA test device. the new list will be:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x1085
0x955 0x3
Also NVIDIA VirtualLink (svid 0x955) uses pin E for display mode.
NVIDIA test device reports vdo of 0x1 so make sure vdo values
always have pin E assignement.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200310121912.57879-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311093003.24604-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel PMC microcontroller on the latest Intel platforms
has a new function that allows configuration of the USB
Multiplexer/DeMultiplexer switches that are under the
control of the PMC.
The Intel PMC mux control (aka. mux-agent) can be used for
swapping the USB data role and for entering alternate modes,
DisplayPort or Thunderbolt3.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-10-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch devices have been named by using the name of the
parent device as base for now, but if for example the
parent device controls multiple muxes, that will not work.
Adding an optional member "name" to the switch descriptor
that can be used for naming the switch during registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding usb_role_switch_get/set_drvdata() functions that the
switch drivers can use for setting and getting private data
pointer that is associated with the switch.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing fwnode_typec_switch_get() and
fwnode_typec_mux_get() functions that work just like
typec_switch_get() and typec_mux_get() but they take struct
fwnode_handle as the first parameter instead of struct
device.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding helpers typec_switch_set() and typec_mux_set() that
simply call the ->set callback function of the mux. These
functions make it possible to set the mux states also from
outside the class code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mux devices have been named by using the name of the
parent device as base until now, but if for example the
parent device has multiple muxes that will not work. This
makes it possible to supply the name for a mux during
registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.
At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.
Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_port_runtime_{resume,suspend}() changes into a
standalone patch to allow conflict-free porting on top of stable v3.9+.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 971fcd492c ("usb: add runtime pm support for usb port device")
Cc: stable@vger.kernel.org # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 253e05724f ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):
*** CID 1458999: Error handling issues (CHECKED_RETURN)
/drivers/usb/core/hub.c: 1869 in hub_probe()
1863
1864 if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
1865 hub->quirk_check_port_auto_suspend = 1;
1866
1867 if (id->driver_info & HUB_QUIRK_DISABLE_AUTOSUSPEND) {
1868 hub->quirk_disable_autosuspend = 1;
>>> CID 1458999: Error handling issues (CHECKED_RETURN)
>>> Calling "usb_autopm_get_interface" without checking return value (as is done elsewhere 97 out of 111 times).
1869 usb_autopm_get_interface(intf);
1870 }
1871
1872 if (hub_configure(hub, &desc->endpoint[0].desc) >= 0)
1873 return 0;
1874
Rather than checking the return value of 'usb_autopm_get_interface()',
switch to the usb_autopm_get_interface_no_resume() API, as per:
On Tue, Feb 25, 2020 at 10:32:32AM -0500, Alan Stern wrote:
------ 8< ------
> This change (i.e. 'ret = usb_autopm_get_interface') is not necessary,
> because the resume operation cannot fail at this point (interfaces
> are always powered-up during probe). A better solution would be to
> call usb_autopm_get_interface_no_resume() instead.
------ 8< ------
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: stable@vger.kernel.org # v4.14+
Reported-by: scan-admin@coverity.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors,
e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors
If data access times out, driver error handling will issue a port
reset.
Sometimes Samsung Fit (090C:1000) flash disk will not respond to
later Set Address or Get Descriptor command.
Adding this quirk to limit max_sectors to 64 sectors to avoid issue
occurring.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.
Signed-off-by: Dan Lazewatsky <dlaz@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4d7201cda2 ("usb: usb251xb: add vdd supply support") didn't
covered the non-DT use-case and so the regualtor_enable() call during
probe will fail on those platforms. Also the commit didn't handled the
error case correctly.
Move devm_regulator_get() out of usb251xb_get_ofdata() to address the
1st issue. This can be done without worries because devm_regulator_get()
handles the non-DT use-case too. Add devm_add_action_or_reset() to
address the 2nd bug.
Fixes: 4d7201cda2 ("usb: usb251xb: add vdd supply support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20200226072644.18490-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.
To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has marked the dequeue trb as link trb, but its next segment
pointer is still itself, it causes the transfer can't go on. Fix
it by set its pointer as the trb address for the next request.
Fixes: f616c3bda4 ("usb: cdns3: Fix dequeue implementation")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per typec spec:
Figure 4-15 Connection State Diagram: DRP
Figure 4-16 Connection State Diagram: DRP with Accessory and Try.SRC
Support
Figure 4-17 Connection State Diagram: DRP with Accessory and Try.SNK
Support
DRP port should move to Unattached.SNK instead of Unattached.SRC if
sink removed.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1582128343-22438-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses only GPIO Descriptor Consumer Interface so include
proper header. This fixes compile test failures (e.g. on i386):
drivers/usb/phy/phy-tegra-usb.c: In function ‘ulpi_phy_power_on’:
drivers/usb/phy/phy-tegra-usb.c:695:2: error:
implicit declaration of function ‘gpiod_set_value_cansleep’ [-Werror=implicit-function-declaration]
drivers/usb/phy/phy-tegra-usb.c: In function ‘tegra_usb_phy_probe’:
drivers/usb/phy/phy-tegra-usb.c:1167:11: error:
implicit declaration of function ‘devm_gpiod_get_from_of_node’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1583234960-24909-1-git-send-email-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
drivers/usb/gadget/udc/net2280.c: In function ‘handle_stat0_irqs_superspeed’:
drivers/usb/gadget/udc/net2280.c:2871:22: warning: statement will never be executed [-Wswitch-unreachable]
2871 | struct net2280_ep *e;
| ^
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/202002201515.DFC51CF@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't confuse user with meaningless warning about the failure in getting
supplies in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200228092808.4580-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200220132017.GA29262@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
udc_name (which is already const char).
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-15-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
udc_name (which is already const char).
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-14-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
driver_name (which is already const char).
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-10-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
driver_name (which is already const char).
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-5-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman