Convert printks to pr_<level> (excludes printk(KERN_DEBUG...)
to be more consistent throughout the xen subsystem.
Add pr_fmt with KBUILD_MODNAME or "xen:" KBUILD_MODNAME
Coalesce formats and add missing word spaces
Add missing newlines
Align arguments and reflow to 80 columns
Remove DRV_NAME from formats as pr_fmt adds the same content
This does change some of the prefixes of these messages
but it also does make them more consistent.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
... as being guest triggerable (e.g. by invoking
XEN_PCI_OP_enable_msi{,x} on a device not being MSI/MSI-X capable).
This is CVE-2013-0231 / XSA-43.
Also make the two messages uniform in both their wording and severity.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This is a minor bugfix and a set of small cleanups; as it is not clear
whether this needs splitting into pieces (and if so, at what
granularity), it is a single combined patch.
- add a missing return statement to an error path in
kill_domain_by_device()
- use pci_is_enabled() rather than raw atomic_read()
- remove a bogus attempt to zero-terminate an already zero-terminated
string
- #define DRV_NAME once uniformly in the shared local header
- make DRIVER_ATTR() variables static
- eliminate a pointless use of list_for_each_entry_safe()
- add MODULE_ALIAS()
- a little bit of constification
- adjust a few messages
- remove stray semicolons from inline function definitions
Signed-off-by: Jan Beulich <jbeulich@suse.com>
[v1: Dropped the resource_size fix, altered the description]
[v2: Fixed cleanpatch.pl comments]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- Remove the slot and controller controller backend as they
are not used.
- Document the find pciback_[read|write]_config_[byte|word|dword]
to make it easier to find.
- Collapse the code from conf_space_capability_msi into pciback_ops.c
- Collapse conf_space_capability_[pm|vpd].c in conf_space_capability.c
[and remove the conf_space_capability.h file]
- Rename all visible functions from pciback to xen_pcibk.
- Rename all the printk/pr_info, etc that use the "pciback" to say
"xen-pciback".
- Convert functions that are not referenced outside the code to be
static to save on name space.
- Do the same thing for structures that are internal to the driver.
- Run checkpatch.pl after the renames and fixup its warnings and
fix any compile errors caused by the variable rename
- Cleanup any structs that checkpath.pl commented about or just
look odd.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we try to setup an fake IRQ handler for legacy interrupts
for devices that only have MSI-X (most if not all SR-IOV cards),
we will fail with this:
pciback[0000:01:10.0]: failed to install fake IRQ handler for IRQ 0! (rc:-38)
Since those cards don't have anything in dev->irq.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the device that is to be shared with a guest is a level device and
the IRQ is shared with the initial domain we need to take actions.
Mainly we install a dummy IRQ handler that will ACK on the interrupt
line so as to not have the initial domain disable the interrupt line.
This dummy IRQ handler is not enabled when the device MSI/MSI-X lines
are set, nor for edge interrupts. And also not for level interrupts
that are not shared amongst devices. Lastly, if the user passes
to the guest all of the PCI devices on the shared line the we won't
install the dummy handler either.
There is also SysFS instrumentation to check its state and turn
IRQ ACKing on/off if necessary.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In cases where the guest is abruptly killed and has not disabled
MSI/MSI-X interrupts we want to do it for it.
Otherwise when the guest is started up and enables MSI, we would
get a WARN() that the device already had been enabled.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This is the host side counterpart to the frontend driver in
drivers/pci/xen-pcifront.c. The PV protocol is also implemented by
frontend drivers in other OSes too, such as the BSDs.
The PV protocol is rather simple. There is page shared with the guest,
which has the 'struct xen_pci_sharedinfo' embossed in it. The backend
has a thread that is kicked every-time the structure is changed and
based on the operation field it performs specific tasks:
XEN_PCI_OP_conf_[read|write]:
Read/Write 0xCF8/0xCFC filtered data. (conf_space*.c)
Based on which field is probed, we either enable/disable the PCI
device, change power state, read VPD, etc. The major goal of this
call is to provide a Physical IRQ (PIRQ) to the guest.
The PIRQ is Xen hypervisor global IRQ value irrespective of the IRQ
is tied in to the IO-APIC, or is a vector. For GSI type
interrupts, the PIRQ==GSI holds. For MSI/MSI-X the
PIRQ value != Linux IRQ number (thought PIRQ==vector).
Please note, that with Xen, all interrupts (except those level shared ones)
are injected directly to the guest - there is no host interaction.
XEN_PCI_OP_[enable|disable]_msi[|x] (pciback_ops.c)
Enables/disables the MSI/MSI-X capability of the device. These operations
setup the MSI/MSI-X vectors for the guest and pass them to the frontend.
When the device is activated, the interrupts are directly injected in the
guest without involving the host.
XEN_PCI_OP_aer_[detected|resume|mmio|slotreset]: In case of failure,
perform the appropriate AER commands on the guest. Right now that is
a cop-out - we just kill the guest.
Besides implementing those commands, it can also
- hide a PCI device from the host. When booting up, the user can specify
xen-pciback.hide=(1:0:0)(BDF..) so that host does not try to use the
device.
The driver was lifted from linux-2.6.18.hg tree and fixed up
so that it could compile under v3.0. Per suggestion from Jesse Barnes
moved the driver to drivers/xen/xen-pciback.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Joe Perches