Some engines optimize operation by reading ahead in the descriptor chain
such that descriptor2 may start execution before descriptor1 completes.
If descriptor2 depends on the result from descriptor1 then a fence is
required (on descriptor2) to disable this optimization. The async_tx
api could implicitly identify dependencies via the 'depend_tx'
parameter, but that would constrain cases where the dependency chain
only specifies a completion order rather than a data dependency. So,
provide an ASYNC_TX_FENCE to explicitly identify data dependencies.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the resources to handle stripe_head operations are allocated
percpu it is possible for raid5d to distribute stripe handling over
multiple cores. This conversion also adds a call to cond_resched() in
the non-multicore case to prevent one core from getting monopolized for
raid operations.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
These routines have been replaced by there asynchronous counterparts.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ Use STRIPE_OP_BIOFILL to offload completion of read requests to
raid_run_ops
2/ Implement a handler for sh->reconstruct_state similar to the raid5 case
(adds handling of Q parity)
3/ Prevent handle_parity_checks6 from running concurrently with 'compute'
operations
4/ Hook up raid_run_ops
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[ Based on an original patch by Yuri Tikhonov ]
Implement the state machine for handling the RAID-6 parities check and
repair functionality. Note that the raid6 case does not need to check
for new failures, like raid5, as it will always writeback the correct
disks. The raid5 case can be updated to check zero_sum_result to avoid
getting confused by new failures rather than retrying the entire check
operation.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the synchronous implementation of stripe dirtying we processed a
degraded stripe with one call to handle_stripe_dirtying6(). I.e.
compute the missing blocks from the other drives, then copy in the new
data and reconstruct the parities.
In the asynchronous case we do not perform stripe operations directly.
Instead, operations are scheduled with flags to be later serviced by
raid_run_ops. So, for the degraded case the final reconstruction step
can only be carried out after all blocks have been brought up to date by
being read, or computed. Like the raid5 case schedule_reconstruction()
sets STRIPE_OP_RECONSTRUCT to request a parity generation pass and
through operation chaining can handle compute and reconstruct in a
single raid_run_ops pass.
[dan.j.williams@intel.com: fixup handle_stripe_dirtying6 gating]
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Modify handle_stripe_fill6 to work asynchronously by introducing
fetch_block6 as the raid6 analog of fetch_block5 (schedule compute
operations for missing/out-of-sync disks).
[dan.j.williams@intel.com: compute D+Q in one pass]
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Extend schedule_reconstruction5 for reuse by the raid6 path. Add
support for generating Q and BUG() if a request is made to perform
'prexor'.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[ Based on an original patch by Yuri Tikhonov ]
The raid_run_ops routine uses the asynchronous offload api and
the stripe_operations member of a stripe_head to carry out xor+pq+copy
operations asynchronously, outside the lock.
The operations performed by RAID-6 are the same as in the RAID-5 case
except for no support of STRIPE_OP_PREXOR operations. All the others
are supported:
STRIPE_OP_BIOFILL
- copy data into request buffers to satisfy a read request
STRIPE_OP_COMPUTE_BLK
- generate missing blocks (1 or 2) in the cache from the other blocks
STRIPE_OP_BIODRAIN
- copy data out of request buffers to satisfy a write request
STRIPE_OP_RECONSTRUCT
- recalculate parity for new data that has entered the cache
STRIPE_OP_CHECK
- verify that the parity is correct
The flow is the same as in the RAID-5 case, and reuses some routines, namely:
1/ ops_complete_postxor (renamed to ops_complete_reconstruct)
2/ ops_complete_compute (updated to set up to 2 targets uptodate)
3/ ops_run_check (renamed to ops_run_check_p for xor parity checks)
[neilb@suse.de: fixes to get it to pass mdadm regression suite]
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ops_complete_compute5 can be reused in the raid6 path if it is updated to
generically handle a second target.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace the flat zero_sum_result with a collection of flags to contain
the P (xor) zero-sum result, and the soon to be utilized Q (raid6 reed
solomon syndrome) zero-sum result. Use the SUM_CHECK_ namespace instead
of DMA_ since these flags will be used on non-dma-zero-sum enabled
platforms.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use percpu memory rather than stack for storing the buffer lists used in
parity calculations. Include space for dma address conversions and pass
that to async_tx via the async_submit_ctl.scribble pointer.
[ Impact: move memory pressure from stack to heap ]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for asynchronous handling of raid6 operations move the
spare page to a percpu allocation to allow multiple simultaneous
synchronous raid6 recovery operations.
Make this allocation cpu hotplug aware to maximize allocation
efficiency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We were removing the drives, from the array, but not
removing symlinks from /sys/.... and not marking the device
as having been removed.
Signed-off-by: NeilBrown <neilb@suse.de>
This "if" don't allow for the possibility that the number of devices
doesn't change, and so sector_nr isn't set correctly in that case.
So change '>' to '>='.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid5 doesn't allow a reshape to restart if it involves writing
over the same part of disk that it would be reading from.
This happens at the beginning of a reshape that increases the number
of devices, at the end of a reshape that decreases the number of
devices, and continuously for a reshape that does not change the
number of devices.
The current code is correct for the "increase number of devices"
case as the critical section at the start is handled by userspace
performing a backup.
It does not work for reducing the number of devices, or the
no-change case.
For 'reducing', we need to invert the test. For no-change we cannot
really be sure things will be safe, so simply require the array
to be read-only, which is how the user-space code which carefully
starts such arrays works.
Signed-off-by: NeilBrown <neilb@suse.de>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
The ->quiesce method is not supposed to stop resync/recovery/reshape,
just normal IO.
But in raid5 we don't have a way to know which stripes are being
used for normal IO and which for resync etc, so we need to wait for
all stripes to be idle to be sure that all writes have completed.
However reshape keeps at least some stripe busy for an extended period
of time, so a call to raid5_quiesce can block for several seconds
needlessly.
So arrange for reshape etc to pause briefly while raid5_quiesce is
trying to quiesce the array so that the active_stripes count can
drop to zero.
Signed-off-by: NeilBrown <neilb@suse.de>
As the internal reshape_progress counter is the main driver
for reshape, the fact that reshape_position sometimes starts with the
wrong value has minimal effect. It is visible in sysfs and that
is all.
Signed-off-by: NeilBrown <neilb@suse.de>
Add missing call to safe_put_page from stop() by unifying open coded
raid5_conf_t de-allocation under free_conf().
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add missing call to safe_put_page from stop() by unifying open coded
raid5_conf_t de-allocation under free_conf().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
User space can set various limits on an md array so that resync waits
when it gets to a certain point, or so that I/O is blocked for a short
while.
When md is waiting against one of these limit, it should use an
interruptible wait so as not to add to the load average, and so are
not to trigger a warning if the wait goes on for too long.
Signed-off-by: NeilBrown <neilb@suse.de>
md allows write to regions on an array to be suspended temporarily.
This allows user-space to participate is aspects of reshape.
In particular, data can be copied with not risk of a race.
We should not be blocking read requests though, so don't.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Switch MD over to the new disk_stack_limits() function which checks for
aligment and adjusts preferred I/O sizes when stacking.
Also indicate preferred I/O sizes where applicable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
At the end of reshape_request we update cyrr_resync_completed
if we are about to pause due to reaching resync_max.
However we update it to the wrong value. We need to add the
"reshape_sectors" that have just been reshaped.
Signed-off-by: NeilBrown <neilb@suse.de>
In the unlikely event that reshape progresses past the current request
while it is waiting for a stripe we need to schedule() before retrying
for 2 reasons:
1/ Prevent list corruption from duplicated list_add() calls without
intervening list_del().
2/ Give the reshape code a chance to make some progress to resolve the
conflict.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).
Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The difference between these two methods is artificial.
Both check that a pending reshape is valid, and perform any
aspect of it that can be done immediately.
'reconfig' handles chunk size and layout.
'check_reshape' handles raid_disks.
So make them just one method.
Signed-off-by: NeilBrown <neilb@suse.de>
Passing the new layout and chunksize as args is not necessary as
the mddev has fields for new_check and new_layout.
This is preparation for combining the check_reshape and reconfig
methods
Signed-off-by: NeilBrown <neilb@suse.de>
In reshape cases that do not change the number of devices,
start_reshape is called without first calling check_reshape.
Currently, the check that the stripe_cache is large enough is
only done in check_reshape. It should be in start_reshape too.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ Raid5 has learned to take over also raid4 and raid6 arrays.
2/ new_chunk in mdp_superblock_1 is in sectors, not bytes.
Signed-off-by: NeilBrown <neilb@suse.de>
A straight-forward conversion which gets rid of some
multiplications/divisions/shifts. The patch also introduces a couple
of new ones, most of which are due to conf->chunk_size still being
represented in bytes. This will be cleaned up in subsequent patches.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics. Since
is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
= is_power_of_2(chunk_sectors)
these bits don't need an adjustment for the shift.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
Now that we support changing the chunksize, we calculate
"reshape_sectors" to be the max of number of sectors in old
and new chunk size.
However there is one please where we still use 'chunksize'
rather than 'reshape_sectors'.
This causes a reshape that reduces the size of chunks to freeze.
Signed-off-by: NeilBrown <neilb@suse.de>
md has functionality to 'quiesce' and array so that all pending
IO completed and no new IO starts. This is used to achieve a
stable state before making internal changes.
Currently this quiescing applies equally to normal IO, resync
IO, and reshape IO.
However there is a problem with applying it to reshape IO.
Reshape can have multiple 'stripe_heads' that must be active together.
If the quiesce come between allocating the first and the last of
such a collection, then we deadlock, as the last will not be allocated
until the quiesce is lifted, the quiesce will not be lifted until the
first (which has been allocated) gets used, and that first cannot be
used until the last is allocated.
It is not necessary to inhibit reshape IO when a quiesce is
requested. Those places in the code that require a full quiesce will
ensure the reshape thread is not running at all.
So allow reshape requests to get access to new stripe_heads without
being blocked by a 'quiesce'.
This only affects in-place reshapes (i.e. where the array does not
grow or shrink) and these are only newly supported. So this patch is
not needed in earlier kernels.
Signed-off-by: NeilBrown <neilb@suse.de>
mddev->raid_disks can be changed and any time by a request from
user-space. It is a suggestion as to what number of raid_disks is
desired.
conf->raid_disks can only be changed by the raid5 module with suitable
locks in place. It is a statement as to the current number of
raid_disks.
There are two places where the latter should be used, but the former
is used. This can lead to a crash when reshaping an array.
This patch changes to mddev-> to conf->
Signed-off-by: NeilBrown <neilb@suse.de>
Prepare the api for the arrival of a new parameter, 'scribble'. This
will allow callers to identify scratchpad memory for dma address or page
address conversions. As this adds yet another parameter, take this
opportunity to convert the common submission parameters (flags,
dependency, callback, and callback argument) into an object that is
passed by reference.
Also, take this opportunity to fix up the kerneldoc and add notes about
the relevant ASYNC_TX_* flags for each routine.
[ Impact: moves api pass-by-value parameters to a pass-by-reference struct ]
Signed-off-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In support of inter-channel chaining async_tx utilizes an ack flag to
gate whether a dependent operation can be chained to another. While the
flag is not set the chain can be considered open for appending. Setting
the ack flag closes the chain and flags the descriptor for garbage
collection. The ASYNC_TX_DEP_ACK flag essentially means "close the
chain after adding this dependency". Since each operation can only have
one child the api now implicitly sets the ack flag at dependency
submission time. This removes an unnecessary management burden from
clients of the api.
[ Impact: clean up and enforce one dependency per operation ]
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A recent patch to raid5.c use min on an int and a sector_t.
This isn't allowed.
So change it to min_t(sector_t,x,y).
Signed-off-by: NeilBrown <neilb@suse.de>
As sector_t in unsigned, we cannot afford to let 'safepos' etc go
negative.
So replace
a -= b;
by
a -= min(b,a);
Signed-off-by: NeilBrown <neilb@suse.de>
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are circumstances when a user-space process might need to
"oversee" a resync/reshape process. For example when doing an
in-place reshape of a raid5, it is prudent to take a backup of each
section before reshaping it as this is the only way to provide
safety against an unplanned shutdown (i.e. crash/power failure).
The sync_max sysfs value can be used to stop the resync from
advancing beyond a particular point.
So user-space can:
suspend IO to the first section and back it up
set 'sync_max' to the end of the section
wait for 'sync_completed' to reach that point
resume IO on the first section and move on to the next section.
However this process requires the kernel and user-space to run in
lock-step which could introduce unnecessary delays.
It would be better if a 'double buffered' approach could be used with
userspace and kernel space working on different sections with the
'next' section always ready when the 'current' section is finished.
One problem with implementing this is that sync_completed is only
guaranteed to be updated when the sync process reaches sync_max.
(it is updated on a time basis at other times, but it is hard to rely
on that). This defeats some of the double buffering.
With this patch, sync_completed (and reshape_position) get updated as
the current position approaches sync_max, so there is room for
userspace to advance sync_max early without losing updates.
To be precise, sync_completed is updated when the current sync
position reaches half way between the current value of sync_completed
and the value of sync_max. This will usually be a good time for user
space to update sync_max.
If sync_max does not get updated, the updates to sync_completed
(together with associated metadata updates) will occur at an
exponentially increasing frequency which will get unreasonably fast
(one update every page) immediately before the process hits sync_max
and stops. So the update rate will be unreasonably fast only for an
insignificant period of time.
Signed-off-by: NeilBrown <neilb@suse.de>
The sync_completed file reports how much of a resync (or recovery or
reshape) has been completed.
However due to the possibility of out-of-order completion of writes,
it is not certain to be accurate.
We have an internal value - mddev->curr_resync_completed - which is an
accurate value (though it might not always be quite so uptodate).
So:
- make curr_resync_completed be uptodate a little more often,
particularly when raid5 reshape updates status in the metadata
- report curr_resync_completed in the sysfs file
- allow poll/select to report all updates to md/sync_completed.
This makes sync_completed completed usable by any external metadata
handler that wants to record this status information in its metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
'zero_sum' does not properly describe the operation of generating parity
and checking that it validates against an existing buffer. Change the
name of the operation to 'val' (for 'validate'). This is in
anticipation of the p+q case where it is a requirement to identify the
target parity buffers separately from the source buffers, because the
target parity buffers will not have corresponding pq coefficients.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We currently update the metadata :
1/ every 3Megabytes
2/ When the place we will write new-layout data to is recorded in
the metadata as still containing old-layout data.
Rule one exists to avoid having to re-do too much reshaping in the
face of a crash/restart. So it should really be time based rather
than size based. So change it to "every 10 seconds".
Rule two turns out to be too harsh when restriping an array
'in-place', as in that case the metadata much be updates for every
stripe.
For the in-place update, it can only possibly be safe from a crash if
some user-space program data a backup of every e.g. few hundred
stripes before allowing them to be reshaped. In that case, the
constant metadata update is pointless.
So only update the metadata if the new metadata will report that the
end of the 'old-layout' data is beyond where we are currently
writing 'new-layout' data.
Signed-off-by: NeilBrown <neilb@suse.de>
... and to be certain the that make_request doesn't wait forever,
add a 'wake_up' when ->reshape_progress has been set to MaxSector
Signed-off-by: NeilBrown <neilb@suse.de>
This was only needed when the code was experimental. Most of it
is well tested now, so the option is no longer useful.
Signed-off-by: NeilBrown <neilb@suse.de>
When we are reshaping an array, it is very important that we read
the data from a particular sector offset before writing new data
at that offset.
In most cases when growing or shrinking an array we read long before
we even consider writing. But when restriping an array without
changing it size, there is a small possibility that we might have
some data to available write before the read has happened at the same
location. This would require some stripes to be in cache already.
To guard against this small possibility, we check, before writing,
that the 'old' stripe at the same location is not in the process of
being read. And we ensure that we mark all 'source' stripes as such
before allowing new 'destination' stripes to proceed.
Signed-off-by: NeilBrown <neilb@suse.de>
If an array has 3 or more devices, we allow the chunksize or layout
to be changed and when a reshape starts, we use these as the 'new'
values.
Signed-off-by: NeilBrown <neilb@suse.de>
This ensures that even when old and new stripes are overlapping,
we will try to read all of the old before having to write any
of the new.
Signed-off-by: NeilBrown <neilb@suse.de>
Add "prev_chunk" to raid5_conf_t, similar to "previous_raid_disks", to
remember what the chunk size was before the reshape that is currently
underway.
This seems like duplication with "chunk_size" and "new_chunk" in
mddev_t, and to some extent it is, but there are differences.
The values in mddev_t are always defined and often the same.
The prev* values are only defined if a reshape is underway.
Also (and more significantly) the raid5_conf_t values will be changed
at the same time (inside an appropriate lock) that the reshape is
started by setting reshape_position. In contrast, the new_chunk value
is set when the sysfs file is written which could be well before the
reshape starts.
Signed-off-by: NeilBrown <neilb@suse.de>
During a raid5 reshape, we have some stripes in the cache that are
'before' the reshape (and are still to be processed) and some that are
'after'. They are currently differentiated by having different
->disks values as the only reshape current supported involves changing
the number of disks.
However we will soon support reshapes that do not change the number
of disks (chunk parity or chunk size). So make the difference more
explicit with a 'generation' number.
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping a raid5 to have fewer devices, we work from the end of
the array to the beginning.
md_do_sync gives addresses to sync_request that go from the beginning
to the end. So largely ignore them use the internal state variable
"reshape_progress" to keep track of what to do next.
Never allow the size to be reduced below the minimum (4 for raid6,
3 otherwise).
We require that the size of the array has already been reduced before
the array is reshaped to a smaller size. This is because simply
reducing the size is an easily reversible operation, while the reshape
is immediately destructive and so is not reversible for the blocks at
the ends of the devices.
Thus to reshape an array to have fewer devices, you must first write
an appropriately small size to md/array_size.
When reshape finished, we remove any drives that are no longer
needed and fix up ->degraded.
Signed-off-by: NeilBrown <neilb@suse.de>
When reducing the number of devices in a raid4/5/6, the reshape
process has to start at the end of the array and work down to the
beginning. So we need to handle expand_progress and expand_lo
differently.
This patch renames "expand_progress" and "expand_lo" to avoid the
implication that anything is getting bigger (expand->reshape) and
every place they are used, we make sure that they are used the right
way depending on whether delta_disks is positive or negative.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently raid5 (the only module that supports restriping)
notices that the reshape has finished be sync_request being
given a large value, and handles any cleanup them.
This patch changes it so md_check_recovery calls into an
explicit finish_reshape method as well.
The clean-up from sync_request can do things that need to be
done promptly, typically things local to the raid5_conf_t
structure.
The "finish_reshape" method is called under the mddev_lock
so it can do things involving reconfiguring the device.
This allows us to get rid of md_set_array_sectors_locked, which
would have caused a deadlock if you tried to stop and array
while a reshape was happening.
Signed-off-by: NeilBrown <neilb@suse.de>
This is the first of four patches which combine to allow md/raid5 to
reduce the number of devices in the array by restriping the data over
a subset of the devices.
If the number of disks in a raid4/5/6 is being reduced, then the
default size must be based on the new number, not the old number
of devices.
In general, it should be based on the smaller of new and old.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the raid6 data processing routines into a standalone module
(raid6_pq) to prepare them to be called from async_tx wrappers and other
non-md drivers/modules. This precludes a circular dependency of raid456
needing the async modules for data processing while those modules in
turn depend on raid456 for the base level synchronous raid6 routines.
To support this move:
1/ The exportable definitions in raid6.h move to include/linux/raid/pq.h
2/ The raid6_call, recovery calls, and table symbols are exported
3/ Extra #ifdef __KERNEL__ statements to enable the userspace raid6test to
compile
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Allow userspace to set the size of the array according to the following
semantics:
1/ size must be <= to the size returned by mddev->pers->size(mddev, 0, 0)
a) If size is set before the array is running, do_md_run will fail
if size is greater than the default size
b) A reshape attempt that reduces the default size to less than the set
array size should be blocked
2/ once userspace sets the size the kernel will not change it
3/ writing 'default' to this attribute returns control of the size to the
kernel and reverts to the size reported by the personality
Also, convert locations that need to know the default size from directly
reading ->array_sectors to <pers>_size. Resync/reshape operations
always follow the default size.
Finally, fixup other locations that read a number of 1k-blocks from
userspace to use strict_blocks_to_sectors() which checks for unsigned
long long to sector_t overflow and blocks to sectors overflow.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Get personalities out of the business of directly modifying
->array_sectors. Lays groundwork to introduce policy on when
->array_sectors can be modified.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for giving userspace control over ->array_sectors we need
to be able to retrieve the 'default' size, and the 'anticipated' size
when a reshape is requested. For personalities that do not reshape emit
a warning if anything but the default size is requested.
In the raid5 case we need to update ->previous_raid_disks to make the
new 'default' size available.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If a raid6 is still in the layout that comes from converting raid5
into a raid6. this will allow us to convert it back again.
Signed-off-by: NeilBrown <neilb@suse.de>
2-drive raid5's aren't very interesting. But if you are converting
a raid1 into a raid5, you will at least temporarily have one. And
that it a good time to set the layout/chunksize for the new RAID5
if you aren't happy with the defaults.
layout and chunksize don't actually affect the placement of data
on a 2-drive raid5, so we just do some internal book-keeping.
Signed-off-by: NeilBrown <neilb@suse.de>
Implement this for RAID6 to be able to 'takeover' a RAID5 array. The
new RAID6 will use a layout which places Q on the last device, and
that device will be missing.
If there are any available spares, one will immediately have Q
recovered onto it.
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly md_unregister_thread is only called when we know that the
thread is NULL, but sometimes we need to check first. It is safer
to put the check inside md_unregister_thread itself.
Signed-off-by: NeilBrown <neilb@suse.de>
.. so that the code to create the private data structures is separate.
This will help with future code to change the level of an active
array.
Signed-off-by: NeilBrown <neilb@suse.de>
DDF requires RAID6 calculations over different devices in a different
order.
For md/raid6, we calculate over just the data devices, starting
immediately after the 'Q' block.
For ddf/raid6 we calculate over all devices, using zeros in place of
the P and Q blocks.
This requires unfortunately complex loops...
Signed-off-by: NeilBrown <neilb@suse.de>
DDF uses different layouts for P and Q blocks than current md/raid6
so add those that are missing.
Also add support for RAID6 layouts that are identical to various
raid5 layouts with the simple addition of one device to hold all of
the 'Q' blocks.
Finally add 'raid5' layouts to match raid4.
These last to will allow online level conversion.
Note that this does not provide correct support for DDF/raid6 yet
as the order in which data blocks are summed to produce the Q block
is significant and different between current md code and DDF
requirements.
Signed-off-by: NeilBrown <neilb@suse.de>
Rather than passing 'pd_idx' and 'qd_idx' to be filled in, pass
a 'struct stripe_head *' and fill in the relevant fields. This is
more extensible.
Signed-off-by: NeilBrown <neilb@suse.de>
Code currently assumes that the devices in a raid6 stripe are
0 1 ... N-1 P Q
in some rotated order. We will shortly add new layouts in which
this strict pattern is broken.
So remove this expectation. We still assume that the data disks
are roughly in-order. However P and Q can be inserted anywhere within
that order.
Signed-off-by: NeilBrown <neilb@suse.de>
This similar to the recent change to get_active_stripe.
There is no functional change, just come rearrangement to make
future patches cleaner.
Signed-off-by: NeilBrown <neilb@suse.de>
Rather than passing 'pd_idx' and 'disks' to these functions, just pass
'previous' which tells whether to use the 'previous' or 'current'
geometry during a reshape, and let init_stripe calculate
disks and pd_idx and anything else it might need.
This is not a substantial simplification and even adds a division.
However we will shortly be adding more complexity to init_stripe
to handle more interesting 'reshape' activities, and without this
change, the interface to these functions would get very complex.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the "size" field of struct mddev_s to "dev_sectors"
and stores the number of 512-byte sectors instead of the number of
1K-blocks in it.
All users of that field, including raid levels 1,4-6,10, are adjusted
accordingly. This simplifies the code a bit because it allows to get
rid of a couple of divisions/multiplications by two.
In order to make checkpatch happy, some minor coding style issues
have also been addressed. In particular, size_store() now uses
strict_strtoull() instead of simple_strtoull().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.
But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.
In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently, the 'chunk_size' of an array must be at-least PAGE_SIZE.
This makes moving an array to a machine with a larger PAGE_SIZE, or
changing the kernel to use a larger PAGE_SIZE, can stop an array from
working.
For RAID10 and RAID4/5/6, this is non-trivial to fix as the resync
process works on whole pages at a time, and assumes them to be wholly
within a stripe. For other raid personalities, this restriction is
not needed at all and can be dropped.
So remove the test on chunk_size from common can, and add it in just
the places where it is needed: raid10 and raid4/5/6.
Signed-off-by: NeilBrown <neilb@suse.de>
Having
function (args)
instead of
function(args)
make is harder to search for calls of particular functions.
So remove all those spaces.
Signed-off-by: NeilBrown <neilb@suse.de>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
raid5 can overflow with more than 255 stripes, and we can increase it
to an int for free on both 32 and 64-bit archs due to the padding.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When we have externally managed metadata, we need to mark a failed
device as 'Blocked' and not allow any writes until that device
have been marked as faulty in the metadata and the Blocked flag has
been removed.
However it is perfectly OK to allow read requests when there is a
Blocked device, and with a readonly array, there may not be any
metadata-handler watching for blocked devices.
So in raid5/raid6 only allow a Blocked device to interfere with
Write request or resync. Read requests go through untouched.
raid1 and raid10 already differentiate between read and write
properly.
Signed-off-by: NeilBrown <neilb@suse.de>
We cannot currently change the size of a write-intent bitmap.
So if we change the size of an array which has such a bitmap, it
tries to set bits beyond the end of the bitmap.
For now, simply reject any request to change the size of an array
which has a bitmap. mdadm can remove the bitmap and add a new one
after the array has changed size.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://neil.brown.name/md:
md: raid10: wake up frozen array
md: do not count blocked devices as spares
md: do not progress the resync process if the stripe was blocked
md: delay notification of 'active_idle' to the recovery thread
md: fix merge error
md: move async_tx_issue_pending_all outside spin_lock_irq
handle_stripe will take no action on a stripe when waiting for userspace
to unblock the array, so do not report completed sectors.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The original STRIPE_OP_IO removal patch had the following hunk:
- for (i = conf->raid_disks; i--; ) {
+ for (i = conf->raid_disks; i--; )
set_bit(R5_Wantwrite, &sh->dev[i].flags);
- if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
- sh->ops.count++;
- }
However it appears the hunk became broken after merging:
- for (i = conf->raid_disks; i--; ) {
+ for (i = conf->raid_disks; i--; )
set_bit(R5_Wantwrite, &sh->dev[i].flags);
set_bit(R5_LOCKED, &dev->flags);
s.locked++;
- if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
- sh->ops.count++;
- }
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some dma drivers need to call spin_lock_bh in their device_issue_pending
routines. This change avoids:
WARNING: at kernel/softirq.c:136 local_bh_enable_ip+0x3a/0x85()
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://neil.brown.name/md: (52 commits)
md: Protect access to mddev->disks list using RCU
md: only count actual openers as access which prevent a 'stop'
md: linear: Make array_size sector-based and rename it to array_sectors.
md: Make mddev->array_size sector-based.
md: Make super_type->rdev_size_change() take sector-based sizes.
md: Fix check for overlapping devices.
md: Tidy up rdev_size_store a bit:
md: Remove some unused macros.
md: Turn rdev->sb_offset into a sector-based quantity.
md: Make calc_dev_sboffset() return a sector count.
md: Replace calc_dev_size() by calc_num_sectors().
md: Make update_size() take the number of sectors.
md: Better control of when do_md_stop is allowed to stop the array.
md: get_disk_info(): Don't convert between signed and unsigned and back.
md: Simplify restart_array().
md: alloc_disk_sb(): Return proper error value.
md: Simplify sb_equal().
md: Simplify uuid_equal().
md: sb_equal(): Fix misleading printk.
md: Fix a typo in the comment to cmd_match().
...
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
splice: fix generic_file_splice_read() race with page invalidation
ramfs: enable splice write
drivers/block/pktcdvd.c: avoid useless memset
cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
scsi: sr avoids useless buffer allocation
block: blk_rq_map_kern uses the bounce buffers for stack buffers
block: add blk_queue_update_dma_pad
DAC960: push down BKL
pktcdvd: push BKL down into driver
paride: push ioctl down into driver
block: use get_unaligned_* helpers
block: extend queue_flag bitops
block: request_module(): use format string
Add bvec_merge_data to handle stacked devices and ->merge_bvec()
block: integrity flags can't use bit ops on unsigned short
cmdfilter: extend default read filter
sg: fix odd style (extra parenthesis) introduced by cmd filter patch
block: add bounce support to blk_rq_map_user_iov
cfq-iosched: get rid of enable_idle being unused warning
allow userspace to modify scsi command filter on per device basis
...
Remove the dubious attempt to prefer 'compute' over 'read'. Not only is it
wrong given commit c337869d (md: do not compute parity unless it is on a failed
drive), but it can trigger a BUG_ON in handle_parity_checks5().
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
When devices are stacked, one device's merge_bvec_fn may need to perform
the mapping and then call one or more functions for its underlying devices.
The following bio fields are used:
bio->bi_sector
bio->bi_bdev
bio->bi_size
bio->bi_rw using bio_data_dir()
This patch creates a new struct bvec_merge_data holding a copy of those
fields to avoid having to change them directly in the struct bio when
going down the stack only to have to change them back again on the way
back up. (And then when the bio gets mapped for real, the whole
exercise gets repeated, but that's a problem for another day...)
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
md_allow_write() marks the metadata dirty while holding mddev->lock and then
waits for the write to complete. For externally managed metadata this causes a
deadlock as userspace needs to take the lock to communicate that the metadata
update has completed.
Change md_allow_write() in the 'external' case to start the 'mark active'
operation and then return -EAGAIN. The expected side effects while waiting for
userspace to write 'active' to 'array_state' are holding off reshape (code
currently handles -ENOMEM), cause some 'stripe_cache_size' change requests to
fail, cause some GET_BITMAP_FILE ioctl requests to fall back to GFP_NOIO, and
cause updates to 'raid_disks' to fail. Except for 'stripe_cache_size' changes
these failures can be mitigated by coordinating with mdmon.
md_write_start() still prevents writes from occurring until the metadata
handler has had a chance to take action as it unconditionally waits for
MD_CHANGE_CLEAN to be cleared.
[neilb@suse.de: return -EAGAIN, try GFP_NOIO]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
From: Dan Williams <dan.j.williams@intel.com>
Commit a4456856 refactored some of the deep code paths in raid5.c into separate
functions. The names chosen at the time do not consistently indicate what is
going to happen to the stripe. So, update the names, and since a stripe is a
cache element use cache semantics like fill, dirty, and clean.
(also, fix up the indentation in fetch_block5)
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
Neil said:
> At the end of ops_run_compute5 you have:
> /* ack now if postxor is not set to be run */
> if (tx && !test_bit(STRIPE_OP_POSTXOR, &s->ops_run))
> async_tx_ack(tx);
>
> It looks odd having that test there. Would it fit in raid5_run_ops
> better?
The intended global interpretation is that raid5_run_ops can build a chain
of xor and memcpy operations. When MD registers the compute-xor it tells
async_tx to keep the operation handle around so that another item in the
dependency chain can be submitted. If we are just computing a block to
satisfy a read then we can terminate the chain immediately. raid5_run_ops
gives a better context for this test since it cares about the entire chain.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
Currently ops_run_biodrain and other locations have extra logic to determine
which blocks are processed in the prexor and non-prexor cases. This can be
eliminated if handle_write_operations5 flags the blocks to be processed in all
cases via R5_Wantdrain. The presence of the prexor operation is tracked in
sh->reconstruct_state.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
Track the state of reconstruct operations (recalculating the parity block
usually due to incoming writes, or as part of array expansion) Reduces the
scope of the STRIPE_OP_{BIODRAIN,PREXOR,POSTXOR} flags to only tracking whether
a reconstruct operation has been requested via the ops_request field of struct
stripe_head_state.
This is the final step in the removal of ops.{pending,ack,complete,count}, i.e.
the STRIPE_OP_{BIODRAIN,PREXOR,POSTXOR} flags only request an operation and do
not track the state of the operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
Track the state of compute operations (recalculating a block from all the other
blocks in a stripe) with a state flag. Reduces the scope of the
STRIPE_OP_COMPUTE_BLK flag to only tracking whether a compute operation has
been requested via the ops_request field of struct stripe_head_state.
Note, the compute operation that is performed in the course of doing a 'repair'
operation (check the parity block, recalculate it and write it back if the
check result is not zero) is tracked separately with the 'check_state'
variable. Compute operations are held off while a 'check' is in progress, and
moving this check out to handle_issuing_new_read_requests5 the helper routine
__handle_issuing_new_read_requests5 can be simplified.
This is another step towards the removal of ops.{pending,ack,complete,count},
i.e. STRIPE_OP_COMPUTE_BLK only requests an operation and does not track the
state of the operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
Track the state of read operations (copying data from the stripe cache to bio
buffers outside the lock) with a state flag. Reduce the scope of the
STRIPE_OP_BIOFILL flag to only tracking whether a biofill operation has been
requested via the ops_request field of struct stripe_head_state.
This is another step towards the removal of ops.{pending,ack,complete,count},
i.e. STRIPE_OP_BIOFILL only requests an operation and does not track the state
of the operation.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
The STRIPE_OP_* flags record the state of stripe operations which are
performed outside the stripe lock. Their use in indicating which
operations need to be run is straightforward; however, interpolating what
the next state of the stripe should be based on a given combination of
these flags is not straightforward, and has led to bugs. An easier to read
implementation with minimal degrees of freedom is needed.
Towards this goal, this patch introduces explicit states to replace what was
previously interpolated from the STRIPE_OP_* flags. For now this only converts
the handle_parity_checks5 path, removing a user of the
ops.{pending,ack,complete,count} fields of struct stripe_operations.
This conversion also found a remaining issue with the current code. There is
a small window for a drive to fail between when we schedule a repair and when
the parity calculation for that repair completes. When this happens we will
writeback to 'failed_num' when we really want to write back to 'pd_idx'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
Let the raid6 path call ops_run_io to get pending i/o submitted.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
In handle_stripe after taking sh->lock we sample some bits into 's' (struct
stripe_head_state):
s.syncing = test_bit(STRIPE_SYNCING, &sh->state);
s.expanding = test_bit(STRIPE_EXPAND_SOURCE, &sh->state);
s.expanded = test_bit(STRIPE_EXPAND_READY, &sh->state);
Use these values from 's' in ops_run_io() rather than re-sampling the bits.
This ensures a consistent snapshot (as seen under sh->lock) is used.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
The R5_Want{Read,Write} flags already gate i/o. So, this flag is
superfluous and we can unconditionally call ops_run_io().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
From: Dan Williams <dan.j.williams@intel.com>
This micro-optimization allowed the raid code to skip a re-read of the
parity block after checking parity. It took advantage of the fact that
xor-offload-engines have their own internal result buffer and can check
parity without writing to memory. Remove it for the following reasons:
1/ It is a layering violation for MD to need to manage the DMA and
non-DMA paths within async_xor_zero_sum
2/ Bad precedent to toggle the 'ops' flags outside the lock
3/ Hard to realize a performance gain as reads will not need an updated
parity block and writes will dirty it anyways.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
For all array types but linear, ->hot_add_disk returns 1 on
success, 0 on failure.
For linear, it returns 0 on success and -errno on failure.
This doesn't cause a functional problem because the ->hot_add_disk
function of linear is used quite differently to the others.
However it is confusing.
So convert all to return 0 for success or -errno on failure
and fix call sites to match.
Signed-off-by: Neil Brown <neilb@suse.de>
i.e. extend the 'md/dev-XXX/slot' attribute so that you can
tell a device to fill an vacant slot in an and md array.
Signed-off-by: Neil Brown <neilb@suse.de>
Turn calls to bi->bi_end_io() into bio_endio(). Apparently bio_endio does
exactly the same error processing as is hardcoded at these places.
bio_endio() avoids recursion (or will soon), so it should be used.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
We shouldn't acknowledge that a stripe has been expanded (When
reshaping a raid5 by adding a device) until the moved data has
actually been written out. However we are currently
acknowledging (by calling md_done_sync) when the POST_XOR
is complete and before the write.
So track in s.locked whether there are pending writes, and don't
call md_done_sync yet if there are.
Note: we all set R5_LOCKED on devices which are are about to
read from. This probably isn't technically necessary, but is
usually done when writing a block, and justifies the use of
s.locked here.
This bug can lead to a crash if an array is stopped while an reshape
is in progress.
Cc: <stable@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
If, while assembling an array, we find a device which is not fully
in-sync with the array, it is important to set the "fullsync" flags.
This is an exact analog to the setting of this flag in hot_add_disk
methods.
Currently, only v1.x metadata supports having devices in an array
which are not fully in-sync (it keep track of how in sync they are).
The 'fullsync' flag only makes a difference when a write-intent bitmap
is being used. In this case it tells recovery to ignore the bitmap
and recovery all blocks.
This fix is already in place for raid1, but not raid5/6 or raid10.
So without this fix, a raid1 ir raid4/5/6 array with version 1.x
metadata and a write intent bitmaps, that is stopped in the middle
of a recovery, will appear to complete the recovery instantly
after it is reassembled, but the recovery will not be correct.
If you might have an array like that, issueing
echo repair > /sys/block/mdXX/md/sync_action
will make sure recovery completes properly.
Cc: <stable@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
If a block is computed (rather than read) then a check/repair operation
may be lead to believe that the data on disk is correct, when infact it
isn't. So only compute blocks for failed devices.
This issue has been around since at least 2.6.12, but has become harder to
hit in recent kernels since most reads bypass the cache.
echo repair > /sys/block/mdN/md/sync_action will set the parity blocks to the
correct state.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the initial array synchronization process there is a window between
when a prexor operation is scheduled to a specific stripe and when it
completes for a sync_request to be scheduled to the same stripe. When
this happens the prexor completes and the stripe is unconditionally marked
"insync", effectively canceling the sync_request for the stripe. Prior to
2.6.23 this was not a problem because the prexor operation was done under
sh->lock. The effect in older kernels being that the prexor would still
erroneously mark the stripe "insync", but sync_request would be held off
and re-mark the stripe as "!in_sync".
Change the write completion logic to not mark the stripe "in_sync" if a
prexor was performed. The effect of the change is to sometimes not set
STRIPE_INSYNC. The worst this can do is cause the resync to stall waiting
for STRIPE_INSYNC to be set. If this were happening, then STRIPE_SYNCING
would be set and handle_issuing_new_read_requests would cause all
available blocks to eventually be read, at which point prexor would never
be used on that stripe any more and STRIPE_INSYNC would eventually be set.
echo repair > /sys/block/mdN/md/sync_action will correct arrays that may
have lost this race.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.
For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.
We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
- We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
which causes the recovery not be be checkpointed.
- We remove spares and then re-added them which loses important state
information.
The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed. If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error. So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.
Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded). Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.
Issue: If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available, do we want to:
1/ complete the current rebuild, then go back and rebuild the new spare or
2/ restart the rebuild from the start and rebuild both devices in
parallel.
Both options can be argued for. The code currently takes option 2 as
a/ this requires least code change
b/ this results in a minimally-degraded array in minimal time.
Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Last night we had scsi problems and a hardware raid unit was offlined
during heavy i/o. While this happened we got for about 3 minutes a huge
number messages like these
Apr 12 03:36:07 pfs1n14 kernel: [197510.696595] raid5:md7: read error not correctable (sector 2993096568 on sdj2).
I guess the high error rate is responsible for not scheduling other events
- during this time the system was not pingable and in the end also other
devices run into scsi command timeouts causing problems on these unrelated
devices as well.
Signed-off-by: Bernd Schubert <bernd-schubert@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.
For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock. So always initialise that lock when allocated.
With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.
Thanks to Dan Williams for review and fixing the silly bugs.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit bd2ab67030 "md: close a livelock window
in handle_parity_checks5" introduced a bug in handling 'repair' operations.
After a repair operation completes we clear the state bits tracking this
operation. However, they are cleared too early and this results in the code
deciding to re-run the parity check operation. Since we have done the repair
in memory the second check does not find a mismatch and thus does not do a
writeback.
Test results:
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
51072
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
0
(also fix incorrect indentation)
Cc: <stable@kernel.org>
Tested-by: George Spelvin <linux@horizon.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allows a userspace metadata handler to take action upon detecting a device
failure.
Based on an original patch by Neil Brown.
Changes:
-added blocked_wait waitqueue to rdev
-don't qualify Blocked with Faulty always let userspace block writes
-added md_wait_for_blocked_rdev to wait for the block device to be clear, if
userspace misses the notification another one is sent every 5 seconds
-set MD_RECOVERY_NEEDED after clearing "blocked"
-kill DoBlock flag, just test mddev->external
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character. It may also output a trailing space
before newline. klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file. This looks ugly.
Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar. Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
strict_strtoul handles the open-coded sanity checks in
raid5_store_stripe_cache_size and raid5_store_preread_threshold
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve write performance by preventing the delayed_list from dumping all its
stripes onto the handle_list in one shot. Delayed stripes are now further
delayed by being held on the 'hold_list'. The 'hold_list' is bypassed when:
* a STRIPE_IO_STARTED stripe is found at the head of 'handle_list'
* 'handle_list' is empty and i/o is being done to satisfy full stripe-width
write requests
* 'bypass_count' is less than 'bypass_threshold'. By default the threshold
is 1, i.e. every other stripe handled is a preread stripe provided the
top two conditions are false.
Benchmark data:
System: 2x Xeon 5150, 4x SATA, mem=1GB
Baseline: 2.6.24-rc7
Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean
Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
* patched: +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512)
Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS)
* patched: +13%
* patched + preread_bypass_threshold = 0: +37%
Changes since v1:
* reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and
make it configurable. This defaults to fairness and modest performance
gains out of the box.
Changes since v2:
* [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not
necessary, the important change was clearing STRIPE_DELAYED in
add_stripe_bio and this has been moved out to make_request for the hang
fix.
* [neilb@suse.de]: simplify get_priority_stripe
* [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is
sampled empty (+11%)
* [dan.j.williams@intel.com]: decrement the bypass_count at the detection
of stripes being naturally promoted off of hold_list +2%. Note, resetting
bypass_count instead of decrementing on these events yields +4% but that is
probably too aggressive.
Changes since v3:
* cosmetic fixups
Tested-by: James W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a failure is detected after a parity check operation has been initiated,
but before it completes handle_parity_checks5 will never quiesce operations on
the stripe.
Explicitly handle this case by "canceling" the parity check, i.e. clear the
STRIPE_OP_CHECK flags and queue the stripe on the handle list again to refresh
any non-uptodate blocks.
Kernel versions >= 2.6.23 are susceptible.
Cc: <stable@kernel.org>
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-3.4.5 on sparc64:
drivers/md/raid5.c: In function `raid5_end_read_request':
drivers/md/raid5.c:1147: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid5.c:1164: warning: long long unsigned int format, long unsigned int arg (arg 3)
drivers/md/raid5.c:1170: warning: long long unsigned int format, long unsigned int arg (arg 3)
sector_t is u64, and we don't know what type the architecture uses to
implement u64 (on some it is unsigned long).
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
raid5's 'make_request' function calls generic_make_request on underlying
devices and if we run out of stripe heads, it could end up waiting for one of
those requests to complete. This is bad as recursive calls to
generic_make_request go on a queue and are not even attempted until
make_request completes.
So: don't make any generic_make_request calls in raid5 make_request until all
waiting has been done. We do this by simply setting STRIPE_HANDLE instead of
calling handle_stripe().
If we need more stripe_heads, raid5d will get called to process the pending
stripe_heads which will call generic_make_request from a
This change by itself causes a performance hit. So add a change so that
raid5_activate_delayed is only called at unplug time, never in raid5. This
seems to bring back the performance numbers. Calling it in raid5d was
sometimes too soon...
Neil said:
How about we queue it for 2.6.25-rc1 and then about when -rc2 comes out,
we queue it for 2.6.24.y?
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Tested-by: dean gaudet <dean@arctic.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As this is more in line with common practice in the kernel. Also swap the
args around to be more like list_for_each.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.
Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync. Rather the entire bitmap is updated
when the resync completes.
This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.
However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap. Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.
[snitzer@gmail.com: export bitmap_cond_end_sync]
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently do not wait for the block from the missing device to be
computed from parity before copying data to the new stripe layout.
The change in the raid6 code is not techincally needed as we don't delay
data block recovery in the same way for raid6 yet. But making the change
now is safer long-term.
This bug exists in 2.6.23 and 2.6.24-rc
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<debug output from Joel's system>
handling stripe 7629696, state=0x14 cnt=1, pd_idx=2 ops=0:0:0
check 5: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ffcffcc0 written 0000000000000000
check 4: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fdd4e360 written 0000000000000000
check 3: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 2: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 1: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ff517e40 written 0000000000000000
check 0: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fd4cae60 written 0000000000000000
locked=4 uptodate=2 to_read=0 to_write=4 failed=0 failed_num=0
for sector 7629696, rmw=0 rcw=0
</debug>
These blocks were prepared to be written out, but were never handled in
ops_run_biodrain(), so they remain locked forever. The operations flags
are all clear which means handle_stripe() thinks nothing else needs to be
done.
This state suggests that the STRIPE_OP_PREXOR bit was sampled 'set' when it
should not have been. This patch cleans up cases where the code looks at
sh->ops.pending when it should be looking at the consistent stack-based
snapshot of the operations flags.
Report from Joel:
Resync done. Patch fix this bug.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Cc: <stable@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
commit 4ae3f847e4 ("md: raid5: fix
clearing of biofill operations") did not get applied correctly,
presumably due to substantial similarities between handle_stripe5 and
handle_stripe6.
This patch moves the chunk of new code from handle_stripe6 (where it isn't
needed (yet)) to handle_stripe5.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Dan Williams" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ops_complete_biofill() runs outside of spin_lock(&sh->lock) and clears the
'pending' and 'ack' bits. Since the test_and_ack_op() macro only checks
against 'complete' it can get an inconsistent snapshot of pending work.
Move the clearing of these bits to handle_stripe5(), under the lock.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant. Remove it.
Now there is no need for bio_endio to subtract the size completed
from bi_size. So don't do that either.
While we are at it, change bi_end_io to return void.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
1/ ops_complete_biofill tried to avoid calling handle_stripe since all the
state necessary to return read completions is available. However the
process of determining whether more read requests are pending requires
locking the stripe (to block add_stripe_bio from updating dev->toead).
ops_complete_biofill can run in tasklet context, so rather than upgrading
all the stripe locks from spin_lock to spin_lock_bh this patch just
unconditionally reschedules handle_stripe after completing the read
request.
2/ ops_complete_biofill needlessly qualified processing R5_Wantfill with
dev->toread. The result being that the 'biofill' pending bit is cleared
before handling the pending read-completions on dev->read. R5_Wantfill can
be unconditionally handled because the 'biofill' pending bit prevents new
R5_Wantfill requests from being seen by ops_run_biofill and
ops_complete_biofill.
Found-by: Yuri Tikhonov <yur@emcraft.com>
[neilb@suse.de: simpler fix for bug 1 than moving code]
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The recent changed to raid5 to allow offload of parity calculation etc
introduced some bugs in the code for growing (i.e. adding a disk to) raid5
and raid6. This fixes them
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Andrew Morton:
[async_memcpy] is very wrong if both ASYNC_TX_KMAP_DST and
ASYNC_TX_KMAP_SRC can ever be set. We'll end up using the same kmap
slot for both src add dest and we get either corrupted data or a BUG.
Evgeniy Polyakov:
Btw, shouldn't it always be kmap_atomic() even if flag is not set.
That pages are usual one returned by alloc_page().
So fix the usage of kmap_atomic and kill the ASYNC_TX_KMAP_DST and
ASYNC_TX_KMAP_SRC flags.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I/O submission requests were already handled outside of the stripe lock in
handle_stripe. Now that handle_stripe is only tasked with finding work,
this logic belongs in raid5_run_ops.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
When a stripe is being expanded bulk copying takes place to move the data
from the old stripe to the new. Since raid5_run_ops only operates on one
stripe at a time these bulk copies are handled in-line under the stripe
lock. In the dma offload case we poll for the completion of the operation.
After the data has been copied into the new stripe the parity needs to be
recalculated across the new disks. We reuse the existing postxor
functionality to carry out this calculation. By setting STRIPE_OP_POSTXOR
without setting STRIPE_OP_BIODRAIN the completion path in handle stripe
can differentiate expand operations from normal write operations.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
When a read bio is attached to the stripe and the corresponding block is
marked R5_UPTODATE, then a read (biofill) operation is scheduled to copy
the data from the stripe cache to the bio buffer. handle_stripe flags the
blocks to be operated on with the R5_Wantfill flag. If new read requests
arrive while raid5_run_ops is running they will not be handled until
handle_stripe is scheduled to run again.
Changelog:
* cleanup to_read and to_fill accounting
* do not fail reads that have reached the cache
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
Check operations are scheduled when the array is being resynced or an
explicit 'check/repair' command was sent to the array. Previously check
operations would destroy the parity block in the cache such that even if
parity turned out to be correct the parity block would be marked
!R5_UPTODATE at the completion of the check. When the operation can be
carried out by a dma engine the assumption is that it can check parity as a
read-only operation. If raid5_run_ops notices that the check was handled
by hardware it will preserve the R5_UPTODATE status of the parity disk.
When a check operation determines that the parity needs to be repaired we
reuse the existing compute block infrastructure to carry out the operation.
Repair operations imply an immediate write back of the data, so to
differentiate a repair from a normal compute operation the
STRIPE_OP_MOD_REPAIR_PD flag is added.
Changelog:
* remove test_and_set/test_and_clear BUG_ONs, Neil Brown
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
handle_stripe will compute a block when a backing disk has failed, or when
it determines it can save a disk read by computing the block from all the
other up-to-date blocks.
Previously a block would be computed under the lock and subsequent logic in
handle_stripe could use the newly up-to-date block. With the raid5_run_ops
implementation the compute operation is carried out a later time outside
the lock. To preserve the old functionality we take advantage of the
dependency chain feature of async_tx to flag the block as R5_Wantcompute
and then let other parts of handle_stripe operate on the block as if it
were up-to-date. raid5_run_ops guarantees that the block will be ready
before it is used in another operation.
However, this only works in cases where the compute and the dependent
operation are scheduled at the same time. If a previous call to
handle_stripe sets the R5_Wantcompute flag there is no facility to pass the
async_tx dependency chain across successive calls to raid5_run_ops. The
req_compute variable protects against this case.
Changelog:
* remove the req_compute BUG_ON
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
After handle_stripe5 decides whether it wants to perform a
read-modify-write, or a reconstruct write it calls
handle_write_operations5. A read-modify-write operation will perform an
xor subtraction of the blocks marked with the R5_Wantprexor flag, copy the
new data into the stripe (biodrain) and perform a postxor operation across
all up-to-date blocks to generate the new parity. A reconstruct write is run
when all blocks are already up-to-date in the cache so all that is needed
is a biodrain and postxor.
On the completion path STRIPE_OP_PREXOR will be set if the operation was a
read-modify-write. The STRIPE_OP_BIODRAIN flag is used in the completion
path to differentiate write-initiated postxor operations versus
expansion-initiated postxor operations. Completion of a write triggers i/o
to the drives.
Changelog:
* make the 'rcw' parameter to handle_write_operations5 a simple flag, Neil Brown
* remove test_and_set/test_and_clear BUG_ONs, Neil Brown
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
All the handle_stripe operations that are to be transitioned to use
raid5_run_ops need a method to coherently gather work under the stripe-lock
and hand that work off to raid5_run_ops. The 'get_stripe_work' routine
runs under the lock to read all the bits in sh->ops.pending that do not
have the corresponding bit set in sh->ops.ack. This modified 'pending'
bitmap is then passed to raid5_run_ops for processing.
The transition from 'ack' to 'completion' does not need similar protection
as the existing release_stripe infrastructure will guarantee that
handle_stripe will run again after a completion bit is set, and
handle_stripe can tolerate a sh->ops.completed bit being set while the lock
is held.
A call to async_tx_issue_pending_all() is added to raid5d to kick the
offload engines once all pending stripe operations work has been submitted.
This enables batching of the submission and completion of operations.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
When the raid acceleration work was proposed, Neil laid out the following
attack plan:
1/ move the xor and copy operations outside spin_lock(&sh->lock)
2/ find/implement an asynchronous offload api
The raid5_run_ops routine uses the asynchronous offload api (async_tx) and
the stripe_operations member of a stripe_head to carry out xor+copy
operations asynchronously, outside the lock.
To perform operations outside the lock a new set of state flags is needed
to track new requests, in-flight requests, and completed requests. In this
new model handle_stripe is tasked with scanning the stripe_head for work,
updating the stripe_operations structure, and finally dropping the lock and
calling raid5_run_ops for processing. The following flags outline the
requests that handle_stripe can make of raid5_run_ops:
STRIPE_OP_BIOFILL
- copy data into request buffers to satisfy a read request
STRIPE_OP_COMPUTE_BLK
- generate a missing block in the cache from the other blocks
STRIPE_OP_PREXOR
- subtract existing data as part of the read-modify-write process
STRIPE_OP_BIODRAIN
- copy data out of request buffers to satisfy a write request
STRIPE_OP_POSTXOR
- recalculate parity for new data that has entered the cache
STRIPE_OP_CHECK
- verify that the parity is correct
STRIPE_OP_IO
- submit i/o to the member disks (note this was already performed outside
the stripe lock, but it made sense to add it as an operation type
The flow is:
1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending
2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the
operation to the async_tx api
3/ async_tx triggers the completion callback routine to set
sh->ops.complete and release the stripe
4/ handle_stripe runs again to finish the operation and optionally submit
new operations that were previously blocked
Note this patch just defines raid5_run_ops, subsequent commits (one per
major operation type) modify handle_stripe to take advantage of this
routine.
Changelog:
* removed ops_complete_biodrain in favor of ops_complete_postxor and
ops_complete_write.
* removed the raid5_run_ops workqueue
* call bi_end_io for reads in ops_complete_biofill, saves a call to
handle_stripe
* explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown
* fix race between async engines and bi_end_io call for reads, Neil Brown
* remove unnecessary spin_lock from ops_complete_biofill
* remove test_and_set/test_and_clear BUG_ONs, Neil Brown
* remove explicit interrupt handling for channel switching, this feature
was absorbed (i.e. it is now implicit) by the async_tx api
* use return_io in ops_complete_biofill
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
Replaces PRINTK with pr_debug, and kills the RAID5_DEBUG definition in
favor of the global DEBUG definition. To get local debug messages just add
'#define DEBUG' to the top of the file.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
handle_stripe5 and handle_stripe6 have very deep logic paths handling the
various states of a stripe_head. By introducing the 'stripe_head_state'
and 'r6_state' objects, large portions of the logic can be moved to
sub-routines.
'struct stripe_head_state' consumes all of the automatic variables that previously
stood alone in handle_stripe5,6. 'struct r6_state' contains the handle_stripe6
specific variables like p_failed and q_failed.
One of the nice side effects of the 'stripe_head_state' change is that it
allows for further reductions in code duplication between raid5 and raid6.
The following new routines are shared between raid5 and raid6:
handle_completed_write_requests
handle_requests_to_failed_array
handle_stripe_expansion
Changes:
* v2: fixed 'conf->raid_disk-1' for the raid6 'handle_stripe_expansion' path
* v3: removed the unused 'dirty' field from struct stripe_head_state
* v3: coalesced open coded bi_end_io routines into return_io()
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
The async_tx api provides methods for describing a chain of asynchronous
bulk memory transfers/transforms with support for inter-transactional
dependencies. It is implemented as a dmaengine client that smooths over
the details of different hardware offload engine implementations. Code
that is written to the api can optimize for asynchronous operation and the
api will fit the chain of operations to the available offload resources.
I imagine that any piece of ADMA hardware would register with the
'async_*' subsystem, and a call to async_X would be routed as
appropriate, or be run in-line. - Neil Brown
async_tx exploits the capabilities of struct dma_async_tx_descriptor to
provide an api of the following general format:
struct dma_async_tx_descriptor *
async_<operation>(..., struct dma_async_tx_descriptor *depend_tx,
dma_async_tx_callback cb_fn, void *cb_param)
{
struct dma_chan *chan = async_tx_find_channel(depend_tx, <operation>);
struct dma_device *device = chan ? chan->device : NULL;
int int_en = cb_fn ? 1 : 0;
struct dma_async_tx_descriptor *tx = device ?
device->device_prep_dma_<operation>(chan, len, int_en) : NULL;
if (tx) { /* run <operation> asynchronously */
...
tx->tx_set_dest(addr, tx, index);
...
tx->tx_set_src(addr, tx, index);
...
async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
} else { /* run <operation> synchronously */
...
<operation>
...
async_tx_sync_epilog(flags, depend_tx, cb_fn, cb_param);
}
return tx;
}
async_tx_find_channel() returns a capable channel from its pool. The
channel pool is organized as a per-cpu array of channel pointers. The
async_tx_rebalance() routine is tasked with managing these arrays. In the
uniprocessor case async_tx_rebalance() tries to spread responsibility
evenly over channels of similar capabilities. For example if there are two
copy+xor channels, one will handle copy operations and the other will
handle xor. In the SMP case async_tx_rebalance() attempts to spread the
operations evenly over the cpus, e.g. cpu0 gets copy channel0 and xor
channel0 while cpu1 gets copy channel 1 and xor channel 1. When a
dependency is specified async_tx_find_channel defaults to keeping the
operation on the same channel. A xor->copy->xor chain will stay on one
channel if it supports both operation types, otherwise the transaction will
transition between a copy and a xor resource.
Currently the raid5 implementation in the MD raid456 driver has been
converted to the async_tx api. A driver for the offload engines on the
Intel Xscale series of I/O processors, iop-adma, is provided in a later
commit. With the iop-adma driver and async_tx, raid456 is able to offload
copy, xor, and xor-zero-sum operations to hardware engines.
On iop342 tiobench showed higher throughput for sequential writes (20 - 30%
improvement) and sequential reads to a degraded array (40 - 55%
improvement). For the other cases performance was roughly equal, +/- a few
percentage points. On a x86-smp platform the performance of the async_tx
implementation (in synchronous mode) was also +/- a few percentage points
of the original implementation. According to 'top' on iop342 CPU
utilization drops from ~50% to ~15% during a 'resync' while the speed
according to /proc/mdstat doubles from ~25 MB/s to ~50 MB/s.
The tiobench command line used for testing was: tiobench --size 2048
--block 4096 --block 131072 --dir /mnt/raid --numruns 5
* iop342 had 1GB of memory available
Details:
* if CONFIG_DMA_ENGINE=n the asynchronous path is compiled away by making
async_tx_find_channel a static inline routine that always returns NULL
* when a callback is specified for a given transaction an interrupt will
fire at operation completion time and the callback will occur in a
tasklet. if the the channel does not support interrupts then a live
polling wait will be performed
* the api is written as a dmaengine client that requests all available
channels
* In support of dependencies the api implicitly schedules channel-switch
interrupts. The interrupt triggers the cleanup tasklet which causes
pending operations to be scheduled on the next channel
* Xor engines treat an xor destination address differently than a software
xor routine. To the software routine the destination address is an implied
source, whereas engines treat it as a write-only destination. This patch
modifies the xor_blocks routine to take a an explicit destination address
to mirror the hardware.
Changelog:
* fixed a leftover debug print
* don't allow callbacks in async_interrupt_cond
* fixed xor_block changes
* fixed usage of ASYNC_TX_XOR_DROP_DEST
* drop dma mapping methods, suggested by Chris Leech
* printk warning fixups from Andrew Morton
* don't use inline in C files, Adrian Bunk
* select the API when MD is enabled
* BUG_ON xor source counts <= 1
* implicitly handle hardware concerns like channel switching and
interrupts, Neil Brown
* remove the per operation type list, and distribute operation capabilities
evenly amongst the available channels
* simplify async_tx_find_channel to optimize the fast path
* introduce the channel_table_initialized flag to prevent early calls to
the api
* reorganize the code to mimic crypto
* include mm.h as not all archs include it in dma-mapping.h
* make the Kconfig options non-user visible, Adrian Bunk
* move async_tx under crypto since it is meant as 'core' functionality, and
the two may share algorithms in the future
* move large inline functions into c files
* checkpatch.pl fixes
* gpl v2 only correction
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
The async_tx api tries to use a dma engine for an operation, but will fall
back to an optimized software routine otherwise. Xor support is
implemented using the raid5 xor routines. For organizational purposes this
routine is moved to a common area.
The following fixes are also made:
* rename xor_block => xor_blocks, suggested by Adrian Bunk
* ensure that xor.o initializes before md.o in the built-in case
* checkpatch.pl fixes
* mark calibrate_xor_blocks __init, Adrian Bunk
Cc: Adrian Bunk <bunk@stusta.de>
Cc: NeilBrown <neilb@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit 5b479c91da.
Quoth Neil Brown:
"It causes an oops when auto-detecting raid arrays, and it doesn't
seem easy to fix.
The array may not be 'open' when do_md_run is called, so
bdev->bd_disk might be NULL, so bd_set_size can oops.
This whole approach of opening an md device before it has been
assembled just seems to get more and more painful. I think I'm going
to have to come up with something clever to provide both backward
comparability with usage expectation, and sane integration into the
rest of the kernel."
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md currently uses ->media_changed to make sure rescan_partitions
is call on md array after they are assembled.
However that doesn't happen until the array is opened, which is later
than some people would like.
So use blkdev_ioctl to do the rescan immediately that the
array has been assembled.
This means we can remove all the ->change infrastructure as it was only used
to trigger a partition rescan.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB doesn't like slashes as it wants to use the cache name as the name of a
directory (or symlink) in sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... still not sure why we need this ....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All that is missing the the function pointers in raid4_pers.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.
Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks". With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar. One place was missed.
This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong. On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. one or more drives can be added and the array will re-stripe
while on-line.
Most of the interesting work was already done for raid5. This just extends it
to raid6.
mdadm newer than 2.6 is needed for complete safety, however any version of
mdadm which support raid5 reshape will do a good enough job in almost all
cases (an 'echo repair > /sys/block/mdX/md/sync_action' is recommended after a
reshape that was aborted and had to be restarted with an such a version of
mdadm).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An error always aborts any resync/recovery/reshape on the understanding that
it will immediately be restarted if that still makes sense. However a reshape
currently doesn't get restarted. With this patch it does.
To avoid restarting when it is not possible to do work, we call into the
personality to check that a reshape is ok, and strengthen raid5_check_reshape
to fail if there are too many failed devices.
We also break some code out into a separate function: remove_and_add_spares as
the indent level for that code was getting crazy.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible for raid5 to be sent a bio that is too big for an underlying
device. So if it is a READ that we pass stright down to a device, it will
fail and confuse RAID5.
So in 'chunk_aligned_read' we check that the bio fits within the parameters
for the target device and if it doesn't fit, fall back on reading through
the stripe cache and making lots of one-page requests.
Note that this is the earliest time we can check against the device because
earlier we don't have a lock on the device, so it could change underneath
us.
Also, the code for handling a retry through the cache when a read fails has
not been tested and was badly broken. This patch fixes that code.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Kai" <epimetreus@fastmail.fm>
Cc: <stable@suse.de>
Cc: <org@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
raid5_mergeable_bvec tries to ensure that raid5 never sees a read request
that does not fit within just one chunk. However as we must always accept
a single-page read, that is not always possible.
So when "in_chunk_boundary" fails, it might be unusual, but it is not a
problem and printing a message every time is a bad idea.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks Jens for alerting me to this.
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <raziebe@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently raid5 depends on clearing the BIO_UPTODATE flag to signal an error
to higher levels. While this should be sufficient, it is safer to explicitly
set the error code as well - less room for confusion.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some vestiges of old code that was used for bypassing the stripe
cache on reads in raid5.c. This was never updated after the change from
buffer_heads to bios, but was left as a reminder.
That functionality has nowe been implemented in a completely different way, so
the old code can go.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stripe_to_pdidx finds the index of the parity disk for a given stripe. It
assumes raid5 in that it uses "disks-1" to determine the number of data disks.
This is incorrect for raid6 but fortunately the two usages cancel each other
out. The only way that 'data_disks' affects the calculation of pd_idx in
raid5_compute_sector is when it is divided into the sector number. But as
that sector number is calculated by multiplying in the wrong value of
'data_disks' the division produces the right value.
So it is innocuous but needs to be fixed.
Also change the calculation of raid_disks in compute_blocknr to make it
more obviously correct (it seems at first to always use disks-1 too).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call the chunk_aligned_read where appropriate.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a bypass-the-cache read fails, we simply try again through the cache. If
it fails again it will trigger normal recovery precedures.
update 1:
From: NeilBrown <neilb@suse.de>
1/
chunk_aligned_read and retry_aligned_read assume that
data_disks == raid_disks - 1
which is not true for raid6.
So when an aligned read request bypasses the cache, we can get the wrong data.
2/ The cloned bio is being used-after-free in raid5_align_endio
(to test BIO_UPTODATE).
3/ We forgot to add rdev->data_offset when submitting
a bio for aligned-read
4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
so we need to invalidate the segment counts.
5/ We don't de-reference the rdev when the read completes.
This means we need to record the rdev to so it is still
available in the end_io routine. Fortunately
bi_next in the original bio is unused at this point so
we can stuff it in there.
6/ We leak a cloned bio if the target rdev is not usable.
From: NeilBrown <neilb@suse.de>
update 2:
1/ When aligned requests fail (read error) they need to be retried
via the normal method (stripe cache). As we cannot be sure that
we can process a single read in one go (we may not be able to
allocate all the stripes needed) we store a bio-being-retried
and a list of bioes-that-still-need-to-be-retried.
When find a bio that needs to be retried, we should add it to
the list, not to single-bio...
2/ We were never incrementing 'scnt' when resubmitting failed
aligned requests.
[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will encourage read request to be on only one device, so we will often be
able to bypass the cache for read requests.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes two if() BUG(); usages to BUG_ON(); so people
can disable it safely.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This is very different from other raid levels and all requests go through a
'stripe cache', and it has congestion management already.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.
So:
- use test-and-set and test-and-clear to synchonise
the In_sync bits with the ->degraded count
- use the spinlock to protect updates to the
degraded count (could use an atomic_t but that
would be a bigger change in code, and isn't
really justified)
- remove un-necessary locking in raid5
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They are not needed. conf->failed_disks is the same as mddev->degraded and
conf->working_disks is conf->raid_disks - mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dan Williams