The UART3 is assigned with IRQ 29 for old SoCs, IRQ 177 for new ones,
and PH1-Pro4 is on the boundary.
PH1-sLD3: UART3 is unavailable
PH1-LD4, PH1-sLD8: only IRQ 29 is supported
PH1-Pro4: both IRQ 29 and 177 are supported
PH1-Pro5, ProXstream2, PH1-LD6b: only IRQ 177 is supported
This SoC can choose either IRQ 29 or IRQ 177, but the former is shared
with another hardware (low speed serial0). The latter is dedicated
for this hardware and more recommended.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SQuE
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500" from Linus Walleij:
- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure the sensors on the TVK board correctly
ARM: u300: remove regulator-compatible usage
ARM: ux500: remove regulator-compatible usage
ARM: ux500: replace legacy *,wakeup property with wakeup-source
ARM: ux500: Assign proper sensor IRQs for Snowball
ARM: ux500: push down Rohm TS to STUIB
The card detect pin is currently called sdmcc-cd.
This patch fixes the typo and renames the pin to sdmmc-cd.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In general, the logic voltage is affected by ddr frequency factors.
We should fix the correct voltage range since assuemd that we have the
ddr frequency driver in mainline in the future.
AFAIK, the 1.8v voltage is used by the SD3.0 card.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rk3288-evb-act8846 and rk3288-evb-rk808 are the power boards of
rk3288-evb, they provide the same power supply interface to the
motherboard. Sort out them, put the public part to rk3288-evb.dtsi,
such as gmac and cpu-supply, leaving only the power section.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
vcc_wl and vcc_lcd are 2 gpio switches for rk3288-evb-act8846 board.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the schematic, the name of REG8 should be vcc_tp, rather
than vcca_tp.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. The baseboard provides a full-size SD
socket (connected to mmc3) in addition to the micro-SD socket on
the SOM itself (which is connected to mmc0).
Enable the mmc3 controller in the dts.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. It provides a set of android-style
buttons (labeled "VOL+", "VOL-", "MENU", "SEARCH", "HOME", "ESC"
and "ENTER") which are connected to a low-resolution ADC via a
resistor network.
This patch adds appropriate button definitions to the board
dts. The voltages assigned to the keys are specified in the
board schematics published by the manufacturer.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Based on similar work for the r8a7791 by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2YO/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nvkl
-----END PGP SIGNATURE-----
Merge tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Reduced Serial Bus (RSB) controller is used to talk to the 3
companion ICs (2 PMICs, 1 RTC/codec IC) on the board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubieboard4 has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* henninger: Remove as it is now replaced by silk
* koelsch: Move SPI partitions to subnode
* porter: Add CAN0 and HS-USB support
* r8a7793/gose: Add QSPI, PFC support
* r8a7793: Add GPIO, DMAC, theral, IPMMU support
* r8a7794/alt: Add DU support
* r8a7794: Disable all IPMMU nodes by default
* r8a779[0134]: Use Use SoC specific binding for rcar-dmac
* r8a779[01], r8a73a4, r8a7740, sh73a0: replace gpio-key, wakeup with
wakeup-source property
* r8a779[14]: Correct "gpio-ranges" properties
* r8a779[14]: Remove bogus imp_clk node
* silk: Add SDHI1 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=snxp
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.5" from Simon Horman:
* henninger: Remove as it is now replaced by silk
* koelsch: Move SPI partitions to subnode
* porter: Add CAN0 and HS-USB support
* r8a7793/gose: Add QSPI, PFC support
* r8a7793: Add GPIO, DMAC, theral, IPMMU support
* r8a7794/alt: Add DU support
* r8a7794: Disable all IPMMU nodes by default
* r8a779[0134]: Use Use SoC specific binding for rcar-dmac
* r8a779[01], r8a73a4, r8a7740, sh73a0: replace gpio-key, wakeup with
wakeup-source property
* r8a779[14]: Correct "gpio-ranges" properties
* r8a779[14]: Remove bogus imp_clk node
* silk: Add SDHI1 support
* tag 'renesas-dt-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
ARM: shmobile: alt: add VIN0, ADV7180 DT support
ARM: shmobile: alt: add I2C1 DT support
ARM: shmobile: alt: Add pfc pins to DT
ARM: shmobile: r8a7794: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7793: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7791: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7790: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7793: Add GPIO nodes to device tree
ARM: shmobile: r8a7794: alt: Enable VGA port
ARM: shmobile: r8a7794: Add DU node to device tree
ARM: shmobile: r8a7794: Add DU0 clock
ARM: shmobile: gose: Add QSPI device to DT
ARM: shmobile: r8a7793: Add QSPI device to DT
ARM: shmobile: r8a7793: Add DMAC devices to DT
ARM: shmobile: koelsch: Move SPI FLASH partitions to subnode
ARM: shmobile: gose: Configure PFC in DT
ARM: shmobile: r8a7793: Add PFC to DT
ARM: shmobile: r8a7793: Add thermal device to DT
ARM: shmobile: henninger: remove board DT
ARM: shmobile: porter: add CAN0 DT support
...
Merge LPC32xx DTS changes for v4.5 from Vladimir Zapolskiy:
Main changes in the series:
- Added description of the second PWM controller device
- Added External Memory Controller device tree node (Primecell PL175)
- Added device tree nodes for standard timer controllers
- USB controllers are grouped
- Various minor clean-ups needed for further development of LPC32xx
* 'lpc32xx-dts' of https://github.com/vzapolskiy/linux:
arm: dts: lpc32xx: move USB controller subdevices into own device node
arm: dts: lpc32xx: add device nodes for standard timers
arm: dts: lpc32xx: add external memory controller device node
arm: dts: ea3250/phy3250: specify phys memory offset for lpc32xx boards
arm: dts: lpc32xx: add device node for the second pwm controller
arm: dts: lpc32xx: add reg property to cpu device node
arm: dts: lpc32xx: add labels to all defined peripheral nodes
arm: dts: lpc32xx: change include syntax to be C preprocessor friendly
Instantiate all serial devices in r8a7793 device tree
and set them as disabled by default.
Based on similar work for the r8a7791 by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Add serial port config to chosen/stdout-path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Otherwise pinctrl won't work. Because of silicon errata for some dm814x
versions, let's also keep bit 18 out of the function-mask and rely on
the bootloader configuration for bit 18 as suggested by
Matthijs van Duin <matthijsvanduin@gmail.com>.
Devices with that need to use bit 18 can override the function-mask in
the board specific dts file if really needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The control module is at offset 0x14000 with size 0x20000, not 0x16000.
This causes the pinctrl driver to not work.
Let's also fix the comments related to the TRM "L4LS Instance Summary"
table as that's what's causing the bad entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although we have hp t410 booting, I noticed that dm814x-evm does not boot
after I got one. This is because we don't have the clocks yet configured
properly. Let's start configuring proper clocks starting with the system
timers and clocks that work with existing mux and divider clock drivers.
Note that the oscillator speed register is different from am335x, dm814x
has only one bit that shows the BTMODE[6] at CONTROL_STATUS[21].
Also note that this only gets the system timers working with the defined
clocks. The PLL clocks are still missing and and the devices may or may
not work depending on what the bootloader has enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The properties specified in the wled node could harm connected hardware,
so move the properties to Honami and disable the platform node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add the generic compatible strings for the PMIC gpio and MPP
modules found on qcom based PMICs.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add an alias for the PMICs found on qcom based SoCs so that the
newly updated dtbTool can find the PMIC compatible string and add
the pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The ifc6540 is an sbc (single board computer) board, so update
the compatible field accordingly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
These clocks are fixed rate board sources that should be in DT.
Add them.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This introduces initial support for the Sony Xperia Z smartphone, including
support for UART, MMC, USB gadget and physical buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Consolidate all labeling of regulators into the core 8064 dtsi file to
make them available from all other dts files.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add devicetree data to add support for hw_rng support
to the apq8064 dts.
Tested on the Nexus7 (2013).
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add and enable the sdhci2 slot, the pinctrl configuration and card
detect.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Introduce the eMMC sdhci node and its pinctrl state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Introduce a gpio-keys node defining the physical keys of the Honami and
the associated pinctrl state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Make sure the blsp1_uart2 pins are in the correct state for the uart.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add support for the SolidRun Armada 388 Clearfog A1 board. This board
has an Armada 388 microsom, dedicated gigabit ethernet, six switched
gigabit ethernet ports, SFP cage, two Mini-PCIe/mSATA slots, a m.2 SATA
slot, and a MikroBUS connector to allow MikroBUS modules to be added.
This DT file adds support for all board facilities with the exception
of full SFP support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The default value of #sound-dai-cells in r8a7778.dtsi is one, while
the /sound/simple-audio-card,cpu device node in r8a7778-bockw.dts uses a
phandle without any extra cells ("<&rcar_sound>"), causing:
/sound/simple-audio-card,cpu: arguments longer than property
asoc-simple-card sound: parse error -22
asoc-simple-card: probe of sound failed with error -22
Override #sound-dai-cells to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When the WiFi support was added to the IGEP0030 board, the MMC subsystem
did not provide a mechanism to define power sequence providers. So a DT
hack was used to toggle the WiFi chip reset and power down pins by using
fake fixed regulators whose enable GPIO was the GPIOs connected to these
pins.
But now the simple MMC power sequence provider can be used for this and
the workaround removed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the WiFi support was added to the IGEP0020 board, the MMC subsystem
did not provide a mechanism to define power sequence providers. So a DT
hack was used to toggle the WiFi chip reset and power down pins by using
fake fixed regulators whose enable GPIO was the GPIOs connected to these
pins.
But now the simple MMC power sequence provider can be used for this and
the workaround removed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These changes cleans up SMP implementaion for Broadcom's
Kona SoC which are required for handling SMP for iProc
family of SoCs at a single place for BCM NSP and BCM Kona.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add device tree changes required for providing SMP support
for Broadcom Northstar Plus SoC.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the Dove divider clocks to the Dove dtsi file.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 388 GP Device Tree file describes two times a regulator
named 'reg_usb2_1_vbus', with the exact same description. This has
been wrong since Armada 388 GP support was introduced.
Fixes: 928413bd85 ("ARM: mvebu: Add Armada 388 General Purpose Development Board support")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit a1bc260bb5 ("gpio: clean up gpio-ranges documentation")
declares the above property deprecated. That was more than 2 years ago.
Remove it, so it doesn't get copied around needlessly.
Based on similar work for the r8a7791 and r8a7794 by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Define the generic R8A7791 part of the EtherAVB device node.
Based on the commit f25d6b9772 ("ARM: shmobile: r8a7790: add EtherAVB DT
support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB clock to the R8A7791 device tree.
Based on the commit 63d2d750c9 ("ARM: shmobile: r8a7790: add EtherAVB
clocks").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the pinctrl support for Broadcom NSP SoC
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yrdreddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable PCIe PHY for both PCIe root complexes on Cygnus
Signed-off-by: Ray Jui <rjui@broadcom.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
[florian: Fix missing #address-cells and #size-cells properties]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a bunch of LEDs missing for the Netgear R8000: wireless, wps, 5Ghz radio
and USB LEDs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the ARM PLL controller which comes standard with the Cortex-A9 found
on the BCM63138 SoCs. This is the same controller as the one found in
the Broadcom iProc architecture, however, we have a separate compatible
string to indicate the integration difference, since the hardware is
different.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
have gpios for card detection, write-protect, vqmmc and vmmc.
This patch adds pinmux for this sdcard interface, then adds regulators
for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
ETH PHYs setup on CL-SOM-AM57X is established in U-Boot along with
bringing them out of reset. This is done by toggling GPIOs belonging
to GPIO2/3 controllers on AM57xx.
Skip resetting ETH PHYs, by adding "ti,no-reset-on-init" to GPIO2/3
controllers DT nodes.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add HDMI connector node without a valid input endpoint.
CompuLab SB-SOM is a carrier board, hence the endpoint
should be added in the board DT with a valid HDMI output.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Startek-kd050c 800x480 LCD panel timings are described in
compulab-sb-som.dtsi.
Add appropriate DT endpoints to connect DPI output and LCD.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On-board EEPROM chip is used for storing a board production info.
Add carrier board EEPROM support (over I2C5 bus).
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
usb1_drvvbus pin is used to Drive-VBUS enable to external charge
pump/power switch.
Add a pinmux for that pin.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add MMC1 support, used for SD/MMC card.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SBC-AM57x is a single board computer designed for industrial and
embedded applications. It is based on the Texas Instruments Sitara AM57x
system-on-chip family. SBC-AM57x is implemented with the CL-SOM-AM57x
computer-on-module providing most of the functions, and SB-SOM-AM57x
carrier board providing additional peripheral functions and connectors.
https://www.compulab.co.il/products/sbcs/sbc-am57x-ti-am5728-am5718-single-board-computer/https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/
Add basic board support, including UART3, used as a serial console.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB support.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On-board spi-flash chip is used as a main boot device.
Add spi-flash chip support (over QSPI bus).
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-SOM-AM57X has two options of main storage devices - eMMC or NAND.
Add eMMC chip support (over MMC2 bus).
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On-board EEPROM chip is used for storing a board production
info.
Add module EEPROM support (over I2C4 bus).
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable I2C3 bus and add appropriate pinmux.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CompuLab CM-SOM-AM57X board.
CL-SOM-AM57x is a miniature System-on-Module (SoM) based on
TI Sitara AM57x ARM Cortex-A15 System-on-Chip family.
https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/
Add basic DT support for standalone module (without a carrier board):
* Memory configuration
* Heartbeat led
* I2C1 and I2C4
* PMIC
* SATA
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On SBC-T43 the mmc1 interface is connected to an SD-Card slot.
Add the necessary muxing and configuration to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CompuLab SB-SOM baseboard is a carrier board for multiple arm-based SoMs.
It currently supports (with minor adjustments to assembly) CM-T43, CM-T54,
and CM-QS600 modules. It is a building block in the SBC-T43 single board
computer, which consists of cm-t43 on top of sb-som-t43.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SB-SOM baseboard comes with an on-board EEPROM. On SBC-T43 this EEPROM
resides on the i2c1 bus. Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SB-SOM comes with a PCA9555 GPIO extender. On SBC-T43 this resides on the
i2c1 bus. Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x has an internal touchscreen controller. Add support for it
on cm-t43.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One of the CompuLab cm-t43 configurations comes with on-board eMMC as
primary storage, residing on the mmc2 interface. Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB support for CompuLab sbc-t43 single board computer,
defaulting to host mode.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T43 comes with 2 ethernet ports connected to the cpsw subsystem, which
has 2 modes of operation: switch mode and dual emac mode.
Add the relevant muxing and set it up to work in dual emac mode by
default.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One of the CompuLab cm-t43 configurations comes with on-board NAND flash as
primary storage. It is partitioned into kernel, dtb, and rootfs partitions.
Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T43 has an on-board 2MB SPI-flash which stores U-Boot and the U-Boot
environment. Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PMIC support for CompuLab cm-t43 module. For now we keep all regulators
enabled until this could be refined with power management support.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T43 has an on-board EEPROM on i2c bus 0. Add it to the device tree.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for SBC-T43: a CM-T43 based single board computer.
CM-T43 is an AM437x based System-on-Module designed to serve as a building
block in embedded applications. SBC-T43 is composed of CM-T43 module on
top of the SB-SOM-T43 baseboard.
Basic support includes UART, GPIO, and I2C.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Minnie provides an elan,ekth3500 touchscreen over the display,
so add the necessary node to enable it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Also known as the Asus Chromebit.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Similar to pinky, brain is a development model and probably also
nearing extinction. But to keep pinky from being lonely I'll keep
the two brain boards around as well, especially as they as well
have easily accessible dut-connectors.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>
The edp-24m clock has two possible sources: the 24MHz oscillator as well
as an external 27MHz input. The power-on-default is the 27MHz clock which
is not supplied on all Rockchip boards. While on all current boards and
also all Veyron Chromebooks the bootloader seems to adapt the muxing to
the internal source, this doesn't seem to be the case on headless veyron
devices like brain and mickey making the edp-24m clock an orphan.
On the hardware side the 27m input also is not connected at all.
With the upcoming deferral of orphan-clocks this results in the power-
domain code deferring, as it cannot request the needed clock and if the
synchronous reset is sucessfullat all in this case is also unknown.
So fix that by making sure, the edp-24m clock is muxed to the internal
24MHz oscillator at all times.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
The Allwinner A80 SoC has an NMI controller. NMI is an external
interrupt pin exclusely used with PMICs and other system critical
peripherals (such as RTC) in Allwinner's reference designs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Ethernet controller found in the Armada 38x SoC's family support
TCP/IP checksumming with frame sizes larger than 1600 bytes, however
only on port 0.
This commit enables it by setting 'tx-csum-limit' to 9800B in
'ethernet@70000' node.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only the bus clock has been assigned, but in reality the
SAI IP has for clock inputs. The driver has been updated to
make use of the additional clock inputs by c3ecef21c3 ("ASoC:
fsl_sai: add sai master mode support"). Due to a bug in the
clock tree, the audio clock has been enabled none the less by
the specified bus clock (see "ARM: imx: clk-vf610: fix SAI
clock tree"), which made master mode even without the proper
clock assigned working.
This patch completes the clock definition for SAI2. On Vybrid,
only two MCLK out of the four options are available (the first
being the bus clock itself). See chapter 8.10.1.2.3 of the
Vybrid Reference manual ("SAI transmitter and receiver options
for MCLK selection"). Note: The audio clocks are only required
in master mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Uart1 rxd is wakeup capable on DRA72 EVM. Hence, mark rxd line as
wakeup capable. This is similar to commit 66b0436977 ("ARM: dts:
dra7-evm: Mark uart1 rxd as wakeup capable") for DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set the alias for qspi to spi0
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The U8500 HREF TVK board actually has a large set of sensors, with
their interrupt lines connected using open drain electronics.
Configure the two accelerometers and two magnetometers so we get
all sensors to actually probe on boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to a commit on the ChromeOS kernel, the temperature of the Speedy
surface is over skin temperature spec. So adjust the thermal settings
to mimic the ChromeOS tree to stay within these spec limits.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
In some cases the machine radiating is very poor,sometime the temperature
is rising very quickly on heavy loading.So we need have more frequent
polling and better granularity.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A80 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A80 SoC has a consumer IR receiver, which is the same as
older SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 has a secondary pin controller. Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The main (24MHz) clock on the A80 is configurable via the PRCM address
space. The low power/speed (32kHz) clock is from an external chip, the
AC100.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the supported PRCM clocks and reset controls to the A80 dtsi.
The DAUDIO module clocks are not supported yet.
Also update clock and reset phandles for r_uart.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sh73a0 has 4 MSIOF devices, located in the A3SP power area.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The 4 MSIOF clocks are MSTP clocks, and children of the SUB clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the alias for qspi to spi0
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree entry for the error location module.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove tps65217.dtsi and adapt all boards, which
used it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for ECAP0 pin.
Add node for PWM backlight device.
Use PWM output from ecap0 as backlight source.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configurations for RGMII1 based CPSW Ethernet pins and
MDIO pins:
- default configuration required for module in active state,
- sleep configuration required for module in inactive state.
Add mac node with single slave device. Add nodes for davinci_mdio and
cpsw_emac0.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for NAND specific GPMC pins.
Add description for GPMC controller. Add child node for NAND flash
including CM-T335 specific partition table to GPMC node.
Enable error-location module (ELM).
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for I2C0 and I2C1 pins.
Add description for I2C0 bus, set clock frequency to 400kHz.
Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for CompuLab cm-t335 module based on AM335X SoC.
CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM)
The module is built around the Texas Instruments Sitara AM3352/4
system-on-chip.
The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board
NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit
Ethernet, CAN bus.
Current patch adds support:
UART0 and GPIO LED
Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
[uri.mashiach@compulab.co.il: the default RAM amount reduced to
128MB to support also the minimal module configuration]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The schematic expects VAUX1 to be 3.0V attached to the debug port.
The schematic expects VAUX4 to be 1.8V.
VAUX4 powers VDDS_CSI2 on processor.
Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When used with the Logic PD development kit, this makes the I2C buses match
the BSP released by Logic PD.
Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup UART2 for communication at 3MBps with flow control.
Signed-off-by: Adam Ford <adam.ford@logicpd.com>
[tony@atomide.com: dropped the kim changes, that binding has been removed]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The development kit schematic expects VAUX1 to be 3.0V. Most users use the development kit as a reference.
The development kit schematic expects VAUX4 to be 1.8V. VAUX4 powers VDDS_CSI2 on processor. If the voltage is too high it could damage the processor.
If it's too low, it won't work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
When used with the Logic PD development kit, this makes the I2C buses match
the BSP released by Logic PD.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add dma channel information to the gpmc. Although not enabled by
default this will allow prefetch-dma to be used.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the missing SPI controller DMA handler in the dm816x DT
node, only properties for the two channels on four were present.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #mbox-cells for dm816x mbox DT node.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add dm816x DT entries for omap4-hwspinlock support as hwmod spinbox.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds ti,timer-pwm property to timers 4 to 7 to permit usage of their
PWM output fonctionnality via the dmtimer driver.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using constants for pinctrl allows better readability and removes
redundancy with comments. AM33XX_IOPAD allows us to use part of the
pinctrl physical address as in the TRM instead of an offset.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the Device Tree source file got merged, some commented pinctrl lines
were left in the file. These are already defined so seems to be a cleanup
that was missed. Delete the unneeded lines from the file.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prefix all partition reg properties to 32-bit to ease readability.
While at it, also remove a stale x in front of boot partition
offset and make some upper-case hex numbers lower-case.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
NAND flash partitions should be part of a partitions sub-node
not the flash node itself. Move the partitions which will also
allow different bootloaders get rid of the stock partitions
easily by removing the partitions node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Current NAND node has an additional flash partition for the whole
flash overlapping with real partitions. Remove this partition as
the whole flash is already represented by the NAND device itself.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Two fixes for the ds1307 alarm and wakeup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6IeZ
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
The Marvell Berlin BG2 has 3 watchdogs which are compatible with the
snps,dw-wdt driver sit in the sysmgr domain. This patch adds the
corresponding device tree nodes.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Marvell Berlin BG2CD has 3 watchdogs which are compatible with the
snps,dw-wdt driver sit in the sysmgr domain. This patch adds the
corresponding device tree nodes.
NOTE: although BG2CD doesn't have a HW sysmgr, but the sysmgr domain
exists.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Marvell Berlin BG2Q has 3 watchdogs which are compatible with the
snps,dw-wdt driver sit in the sysmgr domain. This patch adds the
corresponding device tree nodes.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
on the veyron-minnie board for now and adding the init state for
the over-temperature-protection to prevent glitches making the
system reboot sometimes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWUwH+AAoJEPOmecmc0R2B+mgH+gO2h7FwAa4bv8HcbapZDawX
Pzhu41YxaTZHQEh73waRnGpSVpx5w4r2+pF/fWDC3bRco2zbzAyycPbRwE/9Y7k3
JUzsu7TaiEqxnxEzqdORoilzlRyqMkgR/bV7Tyj8FaxtH/oKu/1b46A5zVhjcdGt
zMHAPtapHAWK1ZfdVBzUjUQQ6uoH0v6nx1CaCteU2/an8BiE/kAV+h6tHgv5YXZh
+cfDChlOYkRO5n+XmUU0Vmq6OKxgJ2N4Rty74aObtLtYzPZZ2PaechUOXRtemWAb
XZ6E5TCS4DhYOpWVPQZ38DDT/v6YDW17dIx7/hKvWnxvtYE9ILgpYDfx6QGuPx4=
=Fiye
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-dts32-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: devicetree fixes for 4.4" from Heiko Stuebner:
Two fixes to Rockchip devicetree files, disabling the mmc-tuning
on the veyron-minnie board for now and adding the init state for
the over-temperature-protection to prevent glitches making the
system reboot sometimes.
* tag 'v4.4-rockchip-dts32-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
- A series of audio changes for dra7 that missed the merge window but turned
out to be necessary to fix a boot time imprecise external abort error and to
getaudio working
- Fix l4 related boot time errors for dm81xx
- Use lockless cldm/pwrdm api in omap4_boot_secondary
- Remove t410 custom abort handler that is no longer needed and may
hide other critical errors
- Mark cpuidle tracepoints as _rcuidle
- Fix module alias for omap-ocp2scp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=G8ox
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Fixes for omaps for v4.4-rc cycle" from Tony Lindgren:
- A series of audio changes for dra7 that missed the merge window but turned
out to be necessary to fix a boot time imprecise external abort error and to
getaudio working
- Fix l4 related boot time errors for dm81xx
- Use lockless cldm/pwrdm api in omap4_boot_secondary
- Remove t410 custom abort handler that is no longer needed and may
hide other critical errors
- Mark cpuidle tracepoints as _rcuidle
- Fix module alias for omap-ocp2scp
* tag 'omap-for-v4.4/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: OMAP2+: remove custom abort handler for t410
ARM: OMAP: DRA7: hwmod: Add data for McASP3
ARM: OMAP2+: hwmod: Add hwmod flag for HWMOD_OPT_CLKS_NEEDED
ARM: dts: dra7: Fix McASP3 node regarding to clocks
bus: omap-ocp2scp: Fix module alias
ARM: OMAP2+: PM: Denote the cpuidle tracepoints as _rcuidle()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into fixes
Linux 4.4-rc2 is backmerged from the keystone fixes.
- Add missing .irq_set_type for i.MX GPC irq_chip. It fixes an issue
that device IRQ type setting doesn't match the one specified in device
tree, since stacked IRQ domain is adopted in GPC driver.
- Fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
- Fix a merge error in Vybrid dts regarding to ADC device property
fsl,adck-max-frequency
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWVbYUAAoJEFBXWFqHsHzOUGwH/1leThviODjyQpau7fEP0qQs
/yfdo+QSKDA/qsv3PK0yyqI1W+eVnlt0EtW38fgnpmgK53dML4eneK5qFTCFJlqp
9+lZAw+yyip3AOK5Cfpr6GnzB5JS60JWotUvrT+ZFIWycL/foGB7By9F7r4KBNWT
P9Lz6bqYVVh/qPAAvWF8Xq0BW8CSdyRkUrjCWJoZjiXRTCxRP4bSF0FYiFw51qMv
x1PZf79ANAsKUtfT8wh71Iiiq10dJqSdmvmnIs1Kk2jfv0fvVz4YKGodNCX/nZdO
xozx+SMcb0j2iefRMoS/wHNFpHAcJC4nnostS9Dk47oFzaatNqELqwBXhxKIJe0=
=ExDB
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "The i.MX fixes for 4.4" from Shawn Guo:
- Add missing .irq_set_type for i.MX GPC irq_chip. It fixes an issue
that device IRQ type setting doesn't match the one specified in device
tree, since stacked IRQ domain is adopted in GPC driver.
- Fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
- Fix a merge error in Vybrid dts regarding to ADC device property
fsl,adck-max-frequency
* tag 'imx-fixes-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
ARM: imx: add platform irq type setting in gpc
ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
Since commit 3fffd12839 ("i2c: allow specifying
separate wakeup interrupt in device tree") we have
automatic wakeup irq support for i2c devices. That
commit missed the fact that rtc-1307 had its own
wakeup irq handling and ended up introducing a
kernel splat for at least Beagle x15 boards.
Fix that by reverting original commit _and_ passing
correct interrupt names on DTS so i2c-core can
choose correct IRQ as wakeup.
Now that we have automatic wakeirq support, we can
revert the original commit which did it manually.
Fixes the following warning:
[ 10.346582] WARNING: CPU: 1 PID: 263 at linux/drivers/base/power/wakeirq.c:43 dev_pm_attach_wake_irq+0xbc/0xd4()
[ 10.359244] rtc-ds1307 2-006f: wake irq already initialized
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the missing L2 cache-controller node, and link the CPU nodes to it.
This will allow migration to the generic l2c OF initialization.
The L2 cache is an ARM L2C-310 (r3p1), of size 512 KiB (64 KiB x 8
ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing L2 cache-controller node, and link the CPU node to it.
This will allow migration to the generic l2c OF initialization.
The L2 cache is an ARM L2C-310 (r3p1-150rel0), of size 256 KiB (32 KiB x
8 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
22b160713c ("ARM: shmobile: alt: Add pfc pins to DT") introduced pfc pins
to the alt device tree but did not reference them. This patch fixes ether
pfc by:
* Referencing ether pins
* Adding and referencing phy1 pins
* Removing ether b pins. These are not used in the configuration
of the alt board used for testing and empirically their presence
prevents ethernet from functioning correctly in that environment.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
22b160713c ("ARM: shmobile: alt: Add pfc pins to DT") introduced pfc pins
to the alt device tree but did not reference them. This patch fixes scif2
pfc by adding references to the scif2 pins.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partitions to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partitions to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partitions to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partition to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The signals output by the DU to the HDMI transmitter use full 24-bit
RGB. Make sure all pins are properly muxed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit a1bc260bb5 ("gpio: clean up gpio-ranges documentation")
declares the above property deprecated. That was more than 2 years ago.
Remove it, so it doesn't get copied around needlessly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit a1bc260bb5 ("gpio: clean up gpio-ranges documentation")
declares the above property deprecated. That was more than 2 years ago.
Remove it, so it doesn't get copied around needlessly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By popular vote, the DT binding includes for reset controllers are located
in include/dt-bindings/reset/. Move the mediatek reset constants in there,
too, to avoid confusion.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Per the Vybrid Reference Manual (section 3.8.6.1), dspi0 has 6 chip
select signals associated with it, while dspi1 has only 4.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a node describing the touchscreen found on the pov protab2-ips9
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the touchscreen controller used on the iNet1 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tie in r8a7794 PFC DU support to the VGA port on the
r8a7794 ALT board.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ensures that the pull-ups for pins SD0_CD and SD0_WP are enabled.
This is one of two features from the DT reference platform that are
still missing in MP.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The boot loader uses scif0, and so must we if we want earlycon to work.
Partially reverts 7c0558941 ("ARM: shmobile: r8a7790: switch from scif
to scifa").
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
OPP bindings got updated to name OPP nodes this way, make changes
according to that.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable the on-chip audio codec
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the on-chip audio codec
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently kernel crash randomly when K2L EVM is booted without
clk_ignore_unused in the bootargs. This workaround is not needed
on other K2 devices such as K2HK and K2E and with this fix, we can
remove the workaround altogether. netcp driver on K2L uses linked
ram on OSR (On chip Static RAM) and requires the clock to this peripheral
enabled for proper functioning. This is the reason for the kernel crash.
So add the clock node to fix this issue.
While at it, remove the workaround documentation as well.
With the fix applied, clk_summary dump shows the clock to OSR enabled.
cat /sys/kernel/debug/clk/clk_summary
------cut--------------
tcp3d-1 0 0 399360000 0 0
tcp3d-0 0 0 399360000 0 0
osr 1 1 399360000 0 0
fftc-0 0 0 399360000 0 0
-----cut----------------
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add support for the IR receiver as present on the Radxa Rock 2 Square
board.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into patchwork
Linux 4.4-rc2
Several PCI media drivers got broken on Kernel 4.4-rc1, due to
pci_set_dma_mask() regressions. So, we need to add those fixes back
for the media drivers to work again.
* tag 'v4.4-rc2': (335 commits)
Linux 4.4-rc2
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
...
Something seems to have gone wrong during the merging of the device
tree changes with the following patch
"ARM: dts: add property for maximum ADC clock frequencies"
The property "fsl,adck-max-frequency" instead of being applied for
the ADC1 node got applied to the esdhc0 node. This patch fixes it.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Fixes: def0641e2f ("ARM: dts: add property for maximum ADC clock frequencies")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace current device tree dummy clocks with real clock support for
Broadcom Northstar Plus SoC
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Replace current device tree dummy clocks with real clock support for
Broadcom Northstar SoCs.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a node describing the AXP152 pmic used on Auxtek T004 boards.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the lcd panel backlight on the pov protab2 ips9
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the lcd panel backlight on the UTOO P66 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the lcd panel backlight on the iNet1 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The iNet1 tablet uses the A10's integrated audio codec, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds basic chip support for Mediatek 2701.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
[matthias.bgg@gmail.com: Fixed reg address of mt2701-timer]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.
Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds syscon-{reboot, poweroff} nodes to allow the
generic syscon-{reboot, poweroff} driver to reset/poweroff exynos5410 SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds syscon-{reboot, poweroff} nodes to allow the
generic syscon-{reboot, poweroff} driver to reset/poweroff exynos5 SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds syscon-{reboot, poweroff} nodes to allow the
generic syscon-{reboot, poweroff} driver to reset/poweroff exynos4 SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds syscon-{reboot, poweroff} nodes to allow the
generic syscon-{reboot, poweroff} driver to reset/poweroff exynos3250 SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add I2C support to the Broadcom Northstar Plus Device Tree. Since no
driver changes are needed to enable this hardware, only the device tree
changes are required to make this functional.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Minor changes to the Broadcom Northstar Plus device tree to make it more
organized and clean. Firstly, move the GIC and L2 cache entries to be
sequential with respect to the memory addresses. Secondly, modify the
address portion of the entry names to reflect the difference from the
range modification.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The act8846 on rock2 boards controls the system power, so add the
appropriate property to allow turning off the board.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The default interrupt-parent has been set in the upper layer, apb@e80000
and apb@fc0000 for example. So if the interrupt-parent isn't changed, we
don't need to set it again. This patch removes the dumplicated
interrupt-parent settings.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The eMMC is non-removable so is marked with the non-removable DT
property to avoid having to redetect it after a suspend/resume.
But it also has the broken-cd property which is wrong since only
one of the DT properties for card detection should be used
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add support for the DENX MCV SoM and MCVEVK baseboard. The SoM contains
eMMC, DRAM, Altera Cyclone V SoC. The baseboard contains CAN ports, UART
ports, STMPE811 touchscreen controller, USB OTG port, ethernet port and
a lot of IO pins.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Cc: Alan Tull <atull@altera.com>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The "reg" entry in the "poweroff" section of "kirkwood-ts219.dtsi"
addressed the wrong uart (0 = console). This patch changes the address
to select uart 1, which is the uart connected to the pic
microcontroller, which can switch the device off.
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 4350a47bba ("ARM: Kirkwood: Make use of the QNAP Power off driver.")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add an ethernet0 alias for the RK3066/RK3188 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an ethernet0 alias for the RK3288 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the "init" anf "sleep" pinctrl as the OTP gpio state.
We need the OTP pin is gpio state before resetting the TSADC controller,
since the tshut polarity will generate a high signal.
"init" pinctrl property is defined by Doug's Patch[0].
Patch[0]:
https://patchwork.kernel.org/patch/7454311/
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The eMMC of the minnie Chromebook doesn't like our current method of
tuning and while there are solutions on the horizon, they still need
investigating. Other Chromebooks tune just fine with the emmc, so
simply disable tuning on Minnie for now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adds the device board-dependent part of the VIN0 device and its ADV7180
video decoder on I2C1, and the interconnection between them.
Based on silk patch by Sergei Shtylyov.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Defines the board-dependent part of the I2C1 device.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PFC is already enabled on the r8a7794.
This adds pins for devices already enabled in DT on
the r8a7794 based alt board.
Based on work by Mitsuhiro Kimura and Hisashi Nakamura.
Cc: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Cc: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
NXP LPC32xx SoC has one USB OTG controller, which is supposed to work
with an external phy (default is NXP ISP1301).
Practically the USB controller contains 5 subdevices:
- host controller 0x3102 0000 -- 0x3102 00FF
- OTG controller 0x3102 0100 -- 0x3102 01FF
- device controller 0x3102 0200 -- 0x3102 02FF
- I2C controller 0x3102 0300 -- 0x3102 03FF
- clock controller 0x3102 0F00 -- 0x3102 0FFF
The USB controller can be considered as a "bus", because the
subdevices above are relatively independent, for example I2C
controller is the same as other two general purpose I2C controllers
found on SoC.
The change is not intended to modify any logic, but it rearranges
existing device nodes, in future it is planned to add a USB clock
controller device node into the same group.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a description of ARM PrimeCell PL175 memory
controller, which is found on NXP LPC32xx SoCs.
The controller supports up to 4 static memory devices mapped to
0xE000 0000 - 0xE3FF FFFF physical memory area.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
In case if SDRAM memory region is not populated by a bootloader,
provide this value in device trees for EA3250 and PHY3250 boards.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
LPC32xx SoCs have two independent PWM controllers, they have different
clock parents, clock gates and even slightly different controls,
each of these two PWM controllers has one output channel. Due to
almost similar controls arranged in a row it is incorrectly assumed
that there is one PWM controller with two channels, fix this problem
in lpc32xx.dtsi, which at the moment prevents separate configuration
of different clock parents and gates for both PWM controllers.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
According to device tree bindings for ARM cpus cpu node must contain a
reg property for enumeration scheme.
The change adds reg = <0x0> indicating that the processor does not
have CPU identification register and updates cell settings.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To simplify writing of dts files for all lpc32xx.dtsi users who adjust
device node properties, add labels to all defined peripheral device
nodes in lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change replaces /include/ to #include in lpc32xx.dtsi and
derivatives, it is required, if C preprocessor is intended to be used
over dtsi/dts files, otherwise errors like one below are generated:
Error: ea3250.dts:15.1-9 syntax error
FATAL ERROR: Unable to parse input tree
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding these properties makes the I2C bus to the demodulators much
more reliable, and we no longer suffer from I2C errors when tuning.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For imx27, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock handling
code any more. Without this patch, it will cause below data
abort when accessing usbmisc registers.
usbcore: registered new interface driver usb-storage
Unhandled fault: external abort on non-linefetch (0x008) at 0xf4424600
pgd = c0004000
[f4424600] *pgd=10000452(bad)
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.1.0-next-20150701-dirty #3089
Hardware name: Freescale i.MX27 (Device Tree Support)
task: c7832b60 ti: c783e000 task.ti: c783e000
PC is at usbmisc_imx27_init+0x4c/0xbc
LR is at usbmisc_imx27_init+0x40/0xbc
pc : [<c03cb5c0>] lr : [<c03cb5b4>] psr: 60000093
sp : c783fe08 ip : 00000000 fp : 00000000
r10: c0576434 r9 : 0000009c r8 : c7a773a0
r7 : 01000000 r6 : 60000013 r5 : c7a776f0 r4 : c7a773f0
r3 : f4424600 r2 : 00000000 r1 : 00000001 r0 : 00000001
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: a0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc783e190)
Stack: (0xc783fe08 to 0xc7840000)
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
Acked-by: Shawn Guo <shawnguo@kernel.org>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7794 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7793 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7791 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7790 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7793 GPIO device nodes that are assumed to be identical
to r8a7791. This matches the data sheet for GPIO and MSTP bits.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the DU device and the VGA port available on the r8a7794
ALT board. The VGA portion of the ALT board is somewhat similar
to the Lager board but in case of ALT the DU1 pins are used
and the X2 clock has a reduced frequency.
This patch does not include any pinctrl (PFC) settings due to lack
of PFC DT integration on r8a7794. At this point the default state
of the boot loader is enough to keep the VGA port working without
changing any pinctrl settings.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0 clock is an MSTP clock, child of the CPG ZX clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The regulator-compatible property from the regulator DT binding was
deprecated and the correct approach is to use the node's name.
This patch has no functional changes since the values of the node's
name and the regulator-compatible match for all the regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The regulator-compatible property from the regulator DT binding was
deprecated and the correct approach is to use the node's name.
This patch has no functional changes since the values of the node's
name and the regulator-compatible match for all the regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MSI Primo81 has a display in portrait mode but a touchscreen
in landscape mode. To have both of them use the same coordinate
system, the touchscreen-swapped-x-y property has to be set
for the touchscreen.
Signed-off-by: Karsten Merker <merker@debian.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Gemei G9 has internal speakers and headphone jack. Audio switching
from internal speakers to headphones is automatically handled by
extra FT2012Q audio amplifier chip that works out of the box.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
ADC seems to be using ldo2 for reference voltage.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add regulator nodes for axp209 using the axp209.dtsi include.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet9f-rev03 tablet has multiple fire-buttons / direction controls,
add support for these using the same axis mapping as ps2 compatible game
controllers with the same stick / button layout use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the on-chip audio codec
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Masahiro Yamada