This patch allows to read temperature
from TMU(Thermal Management Unit) of SAMSUNG EXYNOS4 series of SoC.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ADM1276 is mostly compatible to ADM1275, with added support for input power
measurement. Add support for it to the ADM1275 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADM1275 supports a second current limit, which can be configured as either lower
or upper limit. Add support for it and report it as either lower or upper
critical current limit.
Also replace error return code EINVAL for unsupported pages with ENXIO as this
is more appropriate for the observed condition.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Driver remove functions have an error return value, but rarely return an error
in practice. If a driver does return an error from its remove function, the
driver won't be unloaded and is expected to stay alive.
pmbus_do_remove() is defined as returning an int, but always returns 0 (no
error). Calling code passes that return value on to high level driver
remove functions, but does not evaluate it and removes driver data even if
pmbus_do_remove() returned an error (which it in practice never does). Even if
this code could never cause a real problem, it is nevertheless conceptually
wrong.
To reduce confusion and simplify the code, change pmbus_do_remove() to be a void
function, and have PMBus client drivers always return zero in their driver
remove functions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Return values for functions reading/writing manufacturer specific registers are
poorly explained. Add comments to improve documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Export caseopen alarm status into userspace for Winbond W83627*
and Nuvoton NCT677[56] chips and implement alarm clear attribute.
Second caseopen alarm on NCT6776 is also supported.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Since 8-bit temperature values are now handled in 16-bit struct
members, values have to be cast to s8 for negative temperatures to be
properly handled. This is broken since kernel version 2.6.39
(commit bce26c58df86599c9570cee83eac58bdaae760e4.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The w83627ehf driver is improperly reporting thermal diode sensors as
type 2, instead of 3. This caused "sensors" and possibly other
monitoring tools to report these sensors as "transistor" instead of
"thermal diode".
Furthermore, diode subtype selection (CPU vs. external) is only
supported by the original W83627EHF/EHG. All later models only support
CPU diode type, and some (NCT6776F) don't even have the register in
question so we should avoid reading from it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Storing the struct temp_data pointer allocated from create_core_data()
when returning an error has the potential of leaving around a pointer
to freed memory. Reset it to NULL for error returns.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
With recent change "hwmon: (coretemp) don't use kernel assigned CPU
number as platform device ID", the microcode check is now running on
random CPU. Fix that by checking the microcode before creating the
platform device rather than at probe time.
Also avoid calling TO_PHYS_ID(cpu) twice in the same function, it's
expensive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The only caller of the function obtained the pointer solely for the
purpose of passing it to this function, while it can be easily
determined from the struct platform_device * parameter also passed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These arrays won't ever be written to, so protect them from
unintentional modification.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
... as that has the potential to conflict with (particularly soft) CPU
hot removal and re-adding.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
[guenter.roeck@ericsson.com: use platform device ID as physical CPU id]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed (negative) temperatures were not handled correctly.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # v2.6.38+
gcc -Wextra warns "register is not at beginning of declaration" because the
compiler thinks the parameter has been marked as a 'register' variable, but
the function prototype intended to name the parameter "register" (which is a
reserved keyword).
Signed-off-by: Chris Peterson <cpeterso@cpeterso.com>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With commit c814a4c7c4, the meaning of tempX_max
was changed. It no longer returns the value of bits 8:15 of
MSR_IA32_TEMPERATURE_TARGET, but instead returns the value of CPU threshold
register T1. tempX_max_hyst was added to reflect the value of temperature
threshold register T0.
As it turns out, T0 and T1 are used on some systems, presumably by the BIOS.
Also, T0 and T1 don't have a well defined meaning. The thresholds may be used
as upper or lower limits, and it is not guaranteed that T0 <= T1. Thus, the new
attribute mapping does not reflect the actual usage of the threshold registers.
Also, register contents are changed during runtime by an entity other than the
hwmon driver, meaning the values cached by the driver do not reflect actual
register contents.
Revert most of c814a4c7c4 to address the problem.
Support for T0 and T1 will be added back in with a separate commit, using new
attribute names.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On old CPUs (and even some recent Atom CPUs) TjMax can't be read from
the CPU registers, so it is guessed by the driver using a complex
heuristic which isn't reliable. So let users who know their CPU's
TjMax pass it as a module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Function get_pkg_tjmax is a simplified copy of get_tjmax. Drop it and
always use get_tjmax, result is the same and this avoids code
duplication.
Also make get_tjmax less verbose: don't warn about MSR read failure
when failure was expected, and don't report TjMax in the logs unless
debugging is enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ttarget is initialized when the driver is loaded, but tmin is not.
As a result, tempX_max_hyst attributes read 0. Fix this.
Also use THERM_*_THRESHOLD* constants in these initializations instead
of hard-coding the constants.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature alarms are detected by checking the alarm bit and comparing
temperature limits against the current temperature. For low limits, this
comparison needs to be reversed (temp < limit instead of temp > limit).
This was not taken into account, resulting in wrong alarms if a temperature
fell below a low limit.
Fix by adding a low limit flag in the limit data structure. When creating the
sensor entry, the order of registers to compare is now reversed for low limits.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+
Rewrite the loop walking the id array during probe. The new code is
better adapted to a null-terminated array, and is also clearer and
more efficient than the original.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Current calculation is completely wrong. Add missing brackets to fix it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+
Function i5k_channel_pci_id looks like it can fail, while a better
code design would make it more obvious that it can't. We can even get
rid of the function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Replace unnecessary if with else statement.
This fixes the following (false) compile warning reported with some combinations
of C compiler version and configuration.
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:225: warning: 'low' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'low' was declared here
drivers/hwmon/ntc_thermistor.c:225: warning: 'high' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'high' was declared here
drivers/hwmon/ntc_thermistor.c:294: warning: 'temp' may be used uninitialized in
this function
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
rs_resp is dynamically allocated in aem_read_sensor(), so it should be freed
before exiting in every case. This collects the kfree and the return at
the end of the function.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # 2.6.27+
pmbus_clear_faults() attempts to clear faults on non-existing real pages.
As a result, the command error bit in the status register is set, and faults
are not really cleared.
All byte writes to non-zero pages are requests to clear the status register
on that page. Since non-zero pages are virtual and do not exist on the chip,
there is nothing to do, and such requests have to be ignored. This fixes
above problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual pages and to be able to handle more chips, it is necessary to
virtualise pmbus_write_byte().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
Several vendors implement a second configuration register, which we
check during device detection. Refactor the code to avoid duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With a device ID register value of 0, the SA56004 detection is rather
weak. Check several other register too to confirm the detection, as we
do for other supported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The optional extended local temperature register can never have
address 0, as this address is already used by another register. Thus
we can get rid of flag LM90_HAVE_LOCAL_EXT and simply rely on
reg_local_ext being non-zero to determine if a given chip has this
extension or not. This makes the code more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.
This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
LM95231 is fully compatible to LM95241; only necessary change is to add
chip detection.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX1668 and compatibles have several external temperature sensors, but only a
single FAULT status bit. If a fault occurs, the temperature reported on the
affected sensors is 127 degrees C. Use this knowledge to report fault on
external sensors.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Donggeun Kim