Add code to select SGMII-to-copper mode upon SGMII interface selection.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8995 phy driver just started using gpiod_* functions, which are
declared in linux/gpio/consumer.h, not linux/gpio.h, resulting in a
build failure in randconfig builds that do not have CONFIG_GPIOLIB
enabled:
drivers/net/phy/spi_ks8995.c: In function 'ks8995_probe':
drivers/net/phy/spi_ks8995.c:477:3: error: implicit declaration of function 'gpiod_set_value' [-Werror=implicit-function-declaration]
This changes the header inclusion so it builds in all configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: cd6f288cba ("net: phy: spi_ks8995: add support for resetting switch using GPIO")
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a macro which helps adding new 40NM EPHY entries and reduces the
amount of boilerplate code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is BCM7xxx, we were missing an additional X in the constant naming,
fix that to be consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI TLK10x Ethernet PHYs are similar in the interrupt relevant
registers and so are compatible with the DP83848x devices already
supported.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorganize code by moving the desired interrupt mask definition
out of function. Also rearrange the enable/disable interrupt function
to prevent accidental over-writing of values in registers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After acquiring National Semiconductor, TI appears to have
changed the Vendor Model Number for the DP83848C PHYs,
add this new ID to supported IDs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper macro for defining dp83848 compatible phy devices.
Update copyright info.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MICREL KSZ8795CLX Integrated 5-Port, 10-/100-Managed
Ethernet Switch with Gigabit GMII/RGMII and MII/RMII interfaces.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare creating SPI reads and writes for other switch families.
The KS8995 family uses the straight forward
<8bit CMD><8bit ADDR>
sequence.
To be able to support KSZ8795 family, which uses
<3bit CMD><12bit ADDR><1 bit TR>
make the SPI command creation chip variant dependent.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allows to power down the switch
when it is not used any more.
The patch introduces a new optional property "reset-gpios" denoting an
appropriate GPIO handle, e.g.:
reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the chip variant is now determined by spi_device_id, verify
family and chip id and determine the revision id.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor to use spi_device_id table to facilitate easy
extendability.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the lan87xx_read_status function is getting called the
energy detect mode is enabled again even if it has been
disabled by device tree.
Added private struct to check the energy detect status.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5ea94e7686 ("phy: add phy_mac_interrupt()") to use with
PHY_IGNORE_INTERRUPT added a cancel_work_sync() into phy_mac_interrupt()
which is allowed to sleep, whereas phy_mac_interrupt() is expected to be
callable from interrupt context.
Now that we have fixed how the PHY state machine treats
PHY_IGNORE_INTERRUPT with respect to state changes, we can just set the
new link state, and queue the PHY state machine for execution so it is
going to read the new link state.
For that to work properly, we need to update phy_change() not to try to
invoke any interrupt callbacks if we have configured the PHY device for
PHY_IGNORE_INTERRUPT, because that PHY device and its driver are not
required to implement those.
Fixes: 5ea94e7686 ("phy: add phy_mac_interrupt() to use with PHY_IGNORE_INTERRUPT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c7b49212a ("phy: fix the use of PHY_IGNORE_INTERRUPT") changed
a hunk in phy_state_machine() in the PHY_RUNNING case which was not
needed. The change essentially makes the PHY library treat PHY devices
with PHY_IGNORE_INTERRUPT to keep polling for the PHY device, even
though the intent is not to do it.
Fix this by reverting that specific hunk, which makes the PHY state
machine wait for state changes, and stay in the PHY_RUNNING state for as
long as needed.
Fixes: 2c7b49212a ("phy: fix the use of PHY_IGNORE_INTERRUPT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY status frames are not reliable, the PHY may not be able to send them
during heavy receive traffic. This overflow condition is signaled by the
PHY in the next status frame, but the driver did not make use of it.
Instead it always reported wrong tx timestamps to user space after an
overflow happened because it assigned newly received tx timestamps to old
packets in the queue.
This commit fixes this issue by clearing the tx timestamp queue every time
an overflow happens, so that no timestamps are delivered for overflow
packets. This way time stamping will continue correctly after an overflow.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also use them instead of a magic value when enabling the interrupts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
at803x currently automatically enables the RGMII TX clock delay when the
phy interface mode is PHY_INTERFACE_MODE_RGMII_TXID. The same should be
done when PHY_INTERFACE_MODE_RGMII_ID is specified.
Use a similar logic to enable the RGMII RX clock delay as well.
at803x_context_{save,restore} were not touched because these are only
used on AR8030 which is a RMII phy (RGMII clock delays are irrelevant).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8030 is only a "RMII Fast Ethernet PHY", thus it must not have the
SUPPORTED_1000* bits set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operstate of a networking device initially IF_OPER_UNKNOWN aka
"unknown", updated on carrier state changes (with carrier state being on
by default). This means it will stay unknown unless the carrier state
goes to off at some point, which is not the case if the phy is already
up/connected at startup.
Explicitly turn off the carrier on phy attach, leaving the phy state
machine to turn the carrier on when it has done the initial negotiation.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It used to be that bus->irq was a pointer but after e7f4dc3536
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct, so it can never be NULL. Let's remove the check.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bus = kzalloc() fails then we end up dereferencing bus when we do
"bus->irq[i] = PHY_POLL;". The code is a little simpler if we reverse
the NULL check and return directly on failure.
Fixes: e7f4dc3536 ('mdio: Move allocation of interrupts into core')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8740 has a different phy_id than LAN8710/LAN8720.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 651df21835 ("phy: micrel: Fix finding PHY properties in MAC
node.") only fixes finding PHY properties in MAC node for KSZ9021. This
commit applies the same fix for KSZ9031.
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make device_free and device_remove operations in the mdio device
structure, so the core code does not need to differentiate between
phy devices and generic mdio devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that mdiobus_scan () will only find devices which have a
vendor/product ID in registers 2 and 3. These are typically PHY
devices. Other sort of MDIO devices, such as switches, are not
expected to be found during the scan.
Similarly, __mdiobus_register(), which calls mdiobus_scan() will only
find PHY devices, and other sorts of MDIO devices are expected to be
instantiated from device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should work with any sort of MDIO device which can be
probed on the bus, not just PHY devices. So generalise it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching a driver to a device has both generic parts, and parts which
are specific to PHY devices. Move the PHY specific parts into
phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO PM operations are really PHY device PM operations. So move
them into phy_device. This will be needed when we support devices on
the mdio bus which are not PHYs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio_bus exports three attributes:
- PHY ID is the unique 32-bits identifier for a MDIO device implementing
standard MII registers MII_PHYSID1/2, which is not guaranteed to be the
case for non-standard compliant devices (e.g: Ethernet switches)
- PHY interface describes the data-path of the PHY/MDIO device, which is
not strictly a PHY thing, but is required and needed for PHY devices to
function, a MDIO device could be a control device exclusively
- PHY has fixups describes what the PHY driver may have done, so
completely PHY specific
These are all phy attributes, not generic mdio attributes. So move the
attributes into the phy device code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than use devm_kzalloc(), use the mdio helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_alloc() might return NULL, but its return value is not
checked in mdio_mux_init(). This could potentially lead to a NULL
pointer dereference. Fix it by checking the return value
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Suggested-by: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Roese