Ironlake (and 965GM, which this patch doesn't support) supports a
hardware performance and power management feature that allows it to
adjust to changes in GPU load over time with software help. The goal
if this is to maximize performance/power for a given workload.
This patch enables that feature, which is also a requirement for
supporting Intelligent Power Sharing, a feature which allows for
dynamic budgeting of power between the CPU and GPU in Arrandale
platforms.
Tested-by: ykzhao <yakui.zhao@intel.com>
[anholt: Resolved against the irq handler loop removal]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enabling memory self refresh (SR) on 9xx needs to set additional
register bits. On 945, we need bit 31 of FW_BLC_SELF to enable the
write to self refresh bit and bit 16 to enable the write of self
refresh watermark. On 915, bit 12 of INSTPM is used to enable SR.
SR will take effect when CPU enters C3+ state and its entry/exit
should be automatically controlled by H/W, driver only needs to set
SR enable bits in wm update. But this isn't safe in my test on 945
because GPU is hung. So this patch explicitly enables SR when GPU
is idle, and disables SR when it is busy. In my test on a netbook of
945GSE chipset, it saves about 0.8W idle power.
Signed-off-by: Li Peng <peng.li@intel.com>
[anholt: rebased against 33c5fd121e
by adding disable of INSTPM SR bit on 915GM for two pipe setup]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: bump the UMS driver version number to indicate rv740 fix
drm/radeon/kms: free fence IB if it wasn't emited at IB free time
drm/ttm: fix caching problem on non-PAT systems.
drm/radeon/rv740: fix backend setup
drm/radeon/kms: fix shared ddc detection
drm/radeon/kms/rs600: add connector quirk
vgaarb: fix "target=default" passing
This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
http://bugzilla.kernel.org/show_bug.cgi?id=15328
This fixes a serious regression on AGP/non-PAT systems, where
pages were ending up in the wrong state and slowing down the
whole system.
[airlied: taken this from the bug as the other option is to revert
the change which caused it].
Tested-by: John W. Linville (in bug).
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just compare the i2c id since the i2c structs
may be slighly different.
Fixes fdo bug 26616.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 board lists DVI port as HDMI.
Fixes fdo bug 26605
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 77c1ff3982 fixed the userspace
pointer dereference, but introduced another bug pointed out by Eugene Teo
in RH bug #564264. Instead of comparing the point we were at in the string,
we instead compared the beginning of the string to "default".
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reported-by: Eugene Teo <eteo@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: fix "acpi=ht" boot option
ACPI, i915: blacklist Clevo M5x0N bad_lid state
ACPI: fix High cpu temperature with 2.6.32
ACPI: dock: properly initialize local struct dock_station in dock_add()
ACPI: remove Asus P2B-DS from acpi=ht blacklist
thinkpad-acpi: wrong thermal attribute_group removed in thermal_exit()
ACPI: acpi_bus_{scan,bus,add}: return -ENODEV if no device was found
ACPI: Add NULL pointer check in acpi_bus_start
ACPI: processor: only evaluate _PDC once per processor
ACPI: processor: add kernel command line support for early _PDC eval
* 'for-airlied' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: Force TV encoder DPMS reinit after resume.
drm/nouveau: use mutex for vbios lock
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the vmwgfx module is loaded on top of vesafb, it would operate in
stealth mode in parallel with vesafb, evicting VRAM on dropmaster.
Change that to use the vesafb handover mechanism, like other drmfb drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For usec delays use udelay instead of scheduling, this should
allow reclocking to happen faster. This also was the cause
of reported 33s delays at bootup on certain systems.
fixes: freedesktop.org bug 25506
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.
Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880
RPB: resume previously broken
V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r200 cards have dma engine which can be used to tranfer data
between vram and system memory.
r300 dma engine registers match r200 dma engine. Enabling
dma copy for r200 is simple as hooking r200 asic to already
existing function r300_copy_dma.
Rename r300_dma_copy to r200_dma_copyto reflect that supports
starts from r200 cards.
v2: Created a new asic object for r200 cards.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Setting global asic structure to point to different function
would cause problem in system where is multiple r300 cards
with different bus type.
r300_asic_pcie is just copy from r300_asic with gart tlb
functions replaced with pcie versions.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r6xx/r7xx use the rs600 variant. This old one just
confuses things.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should stop audio-state-reading timer before we turn off engine
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_track_check’:
drivers/gpu/drm/radeon/r600_cs.c:166: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:166: note: ‘bpe’ was declared here
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_parse’:
drivers/gpu/drm/radeon/r600_cs.c:938: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:938: note: ‘bpe’ was declared here
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fence start is for compatibility with UMS X Servers before fence
management. KMS X Servers only started doing tiling after fence
management appeared.
Signed-off-by: Eric Anholt <eric@anholt.net>
As we need more and more controls within MCHBAR for memory config and
power management, this trys to keep MCHBAR enabled from driver load and
only tear down in driver unload.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
With the introduction of the hang-check, we can safely expect that
i915_wait_request() will always return even when the GPU hangs, and so
do not need to open code the wait in order to manually check for the
hang. Also we do not need to always evict all buffers, so only flush
the GPU (and wait for it to idle) for KMS, but continue to evict for UMS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Wrong Lid state reported.
Need to blacklist this machine for LVDS detection.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In testing I've never seen it go past 1 retry anyways but better
safe than sorry.
Reported by Droste on irc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noticed on a DEC Alpha.
Start up into console mode caused 15 unaligned accesses, and starting X
caused another 48.
Signed-off-by: Matt Turner <mattst88@gmail.com>
CC: Jerome Glisse <jglisse@redhat.com>
CC: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the buffer object was already in the requested memory type, but
outside of the requested range it was never moved into the requested range.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When searching for free space in a range, the function could return a node extending outside of the given range.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: hold ref on flip object until it completes
drm/i915: Fix crash while aborting hibernation
drm/i915: Correctly return -ENOMEM on allocation failure in cmdbuf ioctls.
drm/i915: fix pipe source image setting in flip command
drm/i915: fix flip done interrupt on Ironlake
drm/i915: untangle page flip completion
drm/i915: handle FBC and self-refresh better
drm/i915: Increase fb alignment to 64k
drm/i915: Update write_domains on active list after flush.
drm/i915: Rework DPLL calculation parameters for Ironlake
radeon_cs kfree the tracker structure but for r6xx/r7xx we want
to kfree it inside the parse function because we share it with
the UMS code path. Set tracker to NULL after freeing it will
avoid double free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this uses a new entrypoint to invalidate gart entries instead of using 0.
Changed to rather than pointing to 0 address point empty entry to dummy
page. This might help to avoid hard lockup if for some wrong
reasons GPU try to access unmapped GART entry.
I'm not 100% sure this is going to work, we probably need to allocate
a dummy page and point all the GTT entries at it similiar to what AGP does.
but we can test this first I suppose.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's happened time and time again (most recently with the support for EDID
hardcoded in the BIOS ROM) that new code didn't check for rdev->bios being
non-NULL before triggering dereferences of it. This would result in an
oops/panic on setups with no BIOS ROM. Hopefully this central test will be
more robust.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch add cs checker to r600/r700 hw. Command stream checking
will rewrite some of the cs value in order to restrict GPU access
to BO size. This doesn't break old userspace but just enforce safe
value. It should break any things that was using the r600/r700 cs
ioctl to do forbidden things (malicious software), though we are
not aware of such things.
Here is the list of thing we check :
- enforcing resource size
- enforcing color buffer slice tile max, will restrict cb access
- enforcing db buffer slice tile max, will restrict db access
We don't check for shader bigger than the BO in which they are
supposed to be, such use would lead to GPU lockup and is harmless
from security POV, as far as we can tell (note that even checking
for this wouldn't prevent someone to write bogus shader that lead
to lockup).
This patch has received as much testing as humanly possible with
old userspace to check that it didn't break such configuration.
However not all the applications out there were tested, thus it
might broke some odd, rare applications.
[airlied: fix rules for cs checker for parallel builds]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
[clemens@ladisch.de: merged into drm_fb_helper]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
a patch from Roel was wrong, fix this properly, really
if the fb ptrs are different fb changed shuold be true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Kernel has simple_strtol() which would be used as atoi().
This is quite the same fix as in 2cb96f8662
("fbdev: drop custom atoi from drivers/video/modedb.c") because code in
drivers/gpu/drm/drm_fb_helper.c is based on drivers/video/modedb.c.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These ioctls are all protected by their own locking mechanisms so
should be fine to not bother locking around.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mostly obvious simplifications.
The i915 pread/pwrite ioctls, intel_overlay_put_image and
nouveau_gem_new were incorrectly using the locked versions
without locking: this is also fixed in this patch.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch introduces the drm_gem_object_unreference_unlocked
and drm_gem_object_handle_unreference_unlocked functions that
do not require holding struct_mutex.
drm_gem_object_unreference_unlocked calls the new
->gem_free_object_unlocked entry point if available, and
otherwise just takes struct_mutex and just calls ->gem_free_object
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch corrects a userspace pointer dereference in the VGA arbiter
in 2.6.32.1.
copy_from_user() is used at line 822 to copy the contents of buf into
kbuf, but a call to strncmp() on line 964 uses buf rather than kbuf. This
problem led to a GPF in strncmp() when X was started on my x86_32 systems.
X triggered the behavior with a write of "target PCI:0000:01:00.0" to
/dev/vga_arbiter.
The patch has been tested against 2.6.32.1 and observed to correct the GPF
observed when starting X or manually writing the string "target
PCI:0000:01:00.0" to /dev/vga_arbiter.
Signed-off-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-linus' of ../drm-next:
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/radeon/kms: fix screen clearing before fbcon.
drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
drm/radeon/kms: change Kconfig text to reflect the new option.
drm/radeon/kms: suspend and resume audio stuff
ATOM appears to return 0x20 which seems to mean some sort of timeout.
retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>
original evergreen patches we against a kernel tree
without my radeon i2c algo changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a typo in crtc offset setup that set the crtc
instances wrong for all crtcs except the first.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pre-pcie chips seem to use the reference clock
rather than the sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_copy_dma is only available for r200 or newer cards.
Call to radeon_copy_dma would result to NULL pointer
dereference if benchmarking asic without dma engine.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /home/airlied/kernel/drm-next:
nouveau: fix state detection with switchable graphics
drm/nouveau: move dereferences after null checks
drm/nv50: make the pgraph irq handler loop like the pre-nv50 version
drm/nv50: delete ramfc object after disabling fifo, not before
drm/nv50: avoid unloading pgraph context when ctxprog is running
drm/nv50: align size of buffer object to the right boundaries.
drm/nv50: disregard dac outputs in nv50_sor_dpms()
drm/nv50: prevent multiple init tables being parsed at the same time
drm/nouveau: make dp auxch xfer len check for reads only
drm/nv40: make INIT_COMPUTE_MEM a NOP, just like nv50
drm/nouveau: Add proper vgaarb support.
drm/nouveau: Fix fbcon on mixed pre-NV50 + NV50 multicard.
drivers/gpu/drm/nouveau/nouveau_grctx.c: correct NULL test
drm/nouveau: call ttm_bo_wait with the bo lock held to prevent hang
drm/nouveau: Fixup semaphores on pre-nv50 cards.
drm/nouveau: Add getparam to get available PGRAPH units.
drm/nouveau: Add module options to disable acceleration.
drm/nouveau: fix non-vram notifier blocks
Even if this bumps the version to 1 it does not mean the driver is
out of staging. From what we know this is the last backwards
incompatible change to the driver.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When time-based throttling is implemented, we need to bump minor.
When the old way of detecting scanout is removed, we need to bump major.
In the meantime, this change should not break existing user-space.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will prevent things from falling over if the user frees the flip
buffer before we complete the flip, since we'll hold an internal
reference.
Reported-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915) introduced the problem that if s2disk hibernation
is aborted, the system will crash, because i915_pm_freeze() does
nothing, while it should at least reverse some operations carried out
by i915_suspend().
Fix this issue by splitting the i915 suspend into a freeze part a
suspend part, where the latter is not executed before creating a
hibernation image, and the i915 resume into a "low-level" resume part
and a thaw part, where the former is not executed after the image has
been created.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This memset_io was added to debug something way back and got
left behind, memset the fb to black so the borders don't be all white.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MI_DISPLAY_FLIP command needs to be set the same pipe
source image like in pipe source register, e.g source image
size minus one. This fixes screen corrupt issue on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake plane flip interrupt means flip done event already, the
behavior is not like old chips, and perform like other usual interrupt.
So only need to handle flip done event when receiving that interrupt.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When a new page flip is requested, we need to both queue an unpin for
the current framebuffer, and also increment the flip pending count on
the newly submitted buffer.
At flip finish time, we need to unpin the old fb and decrement the flip
pending count on the new buffer.
The old code was conflating the two, and led to hangs when new direct
rendered apps were started, replacing the existing frame buffer. This
patch splits out the buffers and prevents the hangs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
On 945, we need to avoid entering self-refresh if the compressor is
busy, or we may cause display FIFO underruns leading to ugly flicker.
Fixes fdo bug #24314, kernel bug #15043.
Tested-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Julien Cristau <jcristau@debian.org> (fd.o #25371)
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
An untiled framebuffer must be aligned to 64k. This is normally handled
by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
different and do the pinning itself. However, it aligns the buffer
object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
installed onto the output.
Fixes:
KMS error message while initializing modesetting -
render error detected: EIR: 0x10 [i915]
http://bugs.freedesktop.org/show_bug.cgi?id=22936
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Before changing the status of a buffer with a pending write we will await
upon a new flush for that buffer. So we can take advantage of any flushes
posted whilst the buffer is active and pending processing by the GPU, by
clearing its write_domain and updating its last_rendering_seqno -- thus
saving a potential flush in deep queues and improves flushing behaviour
upon eviction for both GTT space and fences.
In order to reduce the time spent searching the active list for matching
write_domains, we move those to a separate list whose elements are
the buffers belong to the active/flushing list with pending writes.
Orignal patch by Chris Wilson <chris@chris-wilson.co.uk>, forward-ported
by me.
In addition to better performance, this also fixes a real bug. Before
this changes, i915_gem_evict_everything didn't work as advertised. When
the gpu was actually busy and processing request, the flush and subsequent
wait would not move active and dirty buffers to the inactive list, but
just to the flushing list. Which triggered the BUG_ON at the end of this
function. With the more tight dirty buffer tracking, all currently busy and
dirty buffers get moved to the inactive list by one i915_gem_flush operation.
I've left the BUG_ON I've used to prove this in there.
References:
Bug 25911 - 2.10.0 causes kernel oops and system hangs
http://bugs.freedesktop.org/show_bug.cgi?id=25911
Bug 26101 - [i915] xf86-video-intel 2.10.0 (and git) triggers kernel oops
within seconds after login
http://bugs.freedesktop.org/show_bug.cgi?id=26101
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Adam Lantos <hege@playma.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Got Ironlake DPLL parameter table, which reflects the hardware
optimized values. So this one trys to list DPLL parameters for
different output types, should potential fix clock issue seen
on new Arrandale CPUs.
This fixes DPLL setting failure on one 1920x1080 dual channel
LVDS for Ironlake. Test has also been made on LVDS panels with
smaller size and CRT/HDMI/DP ports for different monitors on
their all supported modes.
Update:
- Change name of double LVDS to dual LVDS.
- Fix SSC 120M reference clock to use the right range.
Cc: CSJ <changsijay@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Unset the bit that indicates that a ctxprog can continue at the end.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
ramfc is zero'ed upon destruction, so it's safer to do things in the right
order.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- We need to disable pgraph fifo access before checking the current channel,
otherwise we could still hit a running ctxprog.
- The writes to 0x400500 are already handled by pgraph->fifo_access and are
therefore redundant, moreover pgraph fifo access should not be reenabled
before current context is set as invalid. So remove them altogether.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- In the current situation the padding that is added is dangerous to write
to, userspace could potentially overwrite parts of another bo.
- Depth and stencil buffers are supposed to be large enough in general so
the waste of memory should be acceptable.
- Alternatives are hiding the padding from users or splitting vram into 2
zones.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes DVI+VGA on my 9400, and likely a lot of other configurations that
got broken by the previos DVI-over-DP fix.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With DVI and DP plugged, the DVI clock change interrupts being run can
cause DP link training to fail. This adds a spinlock around init table
parsing to prevent this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It appears we aren't required to do memory sizing ourselves on nv40
either. NV40 init tables read a strap from PEXTDEV_BOOT_0 into a
CRTC register, and then later use that value to select a memory
configuration (written to PFB_CFG0, just like INIT_COMPUTE_MEM on
earlier cards) with INIT_IO_RESTRICT_PROG.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We used single shared fbops struct and patched it at fb init time with
pointers to the right variant. On mixed multicard, this meant that
it was either sending NV50-style commands to all cards, or NV04-style
commands to all cards.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_gem_ioctl_cpu_prep calls ttm_bo_wait without the bo lock held.
ttm_bo_wait unlocks that lock, and so must be called with it held.
Currently this bug causes libdrm nouveau_bo_busy() to hang the machine.
Signed-off-by: Luca Barbieri <luca at luca-barbieri.com>
Acked-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Apparently, they generate a PFIFO interrupt each time one of the
semaphore methods is executed if its ctxdma wasn't manually marked as
valid. This patch makes it flip the valid bit in response to the
DMA_SEMAPHORE method (which triggers the IRQ even for a valid ctxdma).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On nv50, this will be needed by applications using CUDA to know
how much stack/local memory to allocate.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
noaccel=1 disables all acceleration and doesn't even attempt
initialising PGRAPH+PFIFO, nofbaccel=1 only makes fbcon unaccelerated.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Due to a thinko, these were previously forced to VRAM even if we allocated
them in GART.
This commit fixes that bug, but keeps the previous behaviour of using VRAM
by default until it's been tested properly across more chipsets.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.
Major changes are DCE4 handling for PLLs for the > 2 crtcs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This merges ugly whitespace we want to keep for consistency
along with the latest upstream changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add an utilities function radeon_ib_bogus_add which will
save an ib into a list of ib which can then be dumped using
debugfs. Once dumped the ib is removed from the list. This
should allow to save & capute ib for further debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This already simplifies code significally and makes it maintaible
in case of adding memory reclocking plus voltage changing in future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
we need a constant sclk for i2c prescale. Also,
get the current sclk when calculating prescale rather
than using the default sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- only r4xx/r5xx/rs6xx/rs740 have clock gating atom table,
so disable it on r6xx. it's already disabled on r7xx
- check to make sure the clock_gating hook exists before
calling it. This avoids a segfault on asics without
that function.
- remove unused static power management function.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The idea is to flag a power state with a certain type and use
that type to decide on what state to select. On r6xx+, we
select a state and then transition between clock modes in that
state. On pre-r6xx, we transition between states directly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The general idea is to validate the current hw state
against the set of power states and select a power
state based on that. This patch just pulls the power
states from the bios and prints the information. It
is not currently hooked up in the actual power management
code. Hooking it up will require reworking the the current
power state selection code and will be handled in a future
patch.
Additionally, we'd need to decide on some default lower
power states for cards without power tables.
v2 - increment state_index after checking for default state
v3 - fix typo in pm init on pre-atom cards, handle pre-atom
cards without x86 bioses
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
V2: reorganize functions, fix modesetting calls
V3: rebase patch, use radeon's workqueue
V4: enable on tested chipsets only, request VBLANK IRQs
V5: enable PM on older hardware (IRQs, mode_fixup, dpms)
V6: use separate dynpm module parameter
V7: drop RADEON_ prefix, set minimum mode for dpms off
V8: update legacy encoder call, fix order in rs600 IRQ
V9: update compute_clocks call in legacy, not only DPMS_OFF
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Set the number of crtcs in rdev at crtc init and use it
whenever we need the crtc count rather than recalculating
it everytime.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only flush the gpu caches before we submit a fence.
This leads to a small performance boost when we take
the extra gpu cache flushes out of the ddx and mesa.
Once this patch is in and the drm version is bumped,
we can remove the flushes from the ddx and drm.
Also, remove the extra cache flushes from the blit
routine.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is used in a lot of places in the atom encoder code.
While here fix the spelling of crtc_source_params.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The panel on the Toshiba A300-1BU laptop does not like the
PLL dividers selected by the avivo pll algo, but works fine
using the older method. Add a quirk to handle it.
Should fix fdo bug 26358.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Rework the pll algo selection so that the pll algo
in use can be selected more easily. This allows
us to select different pll divider selection algos
for specific monitors that work better with one algo
or the other. This is needed for the next patch which
adds an LVDS pll quirk for a specific notebook.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switch some magic numbers to their proper defines.
The register header madness needs to be cleaned up
at some point.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some servers hardcode an edid in rom so that they will
work properly with KVMs. This is a port of the relevant
code from the ddx.
[airlied: reworked to validate edid at boot stage - and
remove special quirk, if there is a valid EDID in the BIOS rom
we'll just try and use it.]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some servers have two VGA ports but only report
one in the bios connector tables. On these systems
always set up the TV DAC so that it displays properly
even if the bios is wrong.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
wire hw i2c support into radeon i2c algo.
fixes merged:
- handle bus probing correctly
- use meaningful error numbers
- abort if transaction fails
- The line mapping is different depending on the asic.
- protect hw i2c engine with a mutex
- rs300 doesn't have a pin select bit
- r200 has a different pin select setup
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is strange - like really really strange, twilight zone of strange.
VGA ports have DDC buses, but sometimes for some reasons the BIOS
says we don't and we oops - AMD mentioned bios bugs so we'll have
to add quirks.
reported on irc by nirbheek and
https://bugzilla.redhat.com/show_bug.cgi?id=554323
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ingo pointed out that we really don't give the user enough warning to make
a decision here. So revise the Kconfig text with a better warning.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Fix leak of relocs along do_execbuffer error path
drm/i915: slow acpi_lid_open() causes flickering - V2
drm/i915: Disable SR when more than one pipe is enabled
drm/i915: page flip support for Ironlake
drm/i915: Fix the incorrect DMI string for Samsung SX20S laptop
drm/i915: Add support for SDVO composite TV
drm/i915: don't trigger ironlake vblank interrupt at irq install
drm/i915: handle non-flip pending case when unpinning the scanout buffer
drm/i915: Fix the device info of Pineview
drm/i915: enable vblank interrupt on ironlake
drm/i915: Prevent use of uninitialized pointers along error path.
drm/i915: disable hotplug detect before Ironlake CRT detect
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix r300 vram width calculations
drm/radeon/kms: rs400/480 MC setup is different than r300.
drm/radeon/kms: make initial state of load detect property correct.
drm/radeon/kms: disable HDMI audio for now on rv710/rv730
drm/radeon/kms: don't call suspend path before cleaning up GPU
drivers/gpu/drm/radeon/radeon_combios.c: fix warning
ati_pcigart: fix printk format warning
drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
drm/radeon/kms: move blit initialization after we disabled VGA
Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.
Implement a new rs400 mc idle function to fix this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.
Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix ati_pcigart printk format warning:
drivers/gpu/drm/ati_pcigart.c:115: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cache flush is required in case CPU is accessing rendered data.
This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.
v2 Fix comment ordering in r100_fence_ring_emit and remove extra
defines added in first version.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:
http://bugzilla.kernel.org/show_bug.cgi?id=15186
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Following a gpu hang, we would leak the relocation buffer. So simply
earrange the error path to always free the relocation buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
acpi_lid_open() could take up to 10ms on my computer. Some component is
calling the drm GETCONNECTOR ioctl many times in a row. This results in
flickering (for example, when starting a video). Fix it by assuming an
always connected lid status.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
Self Refresh should be disabled on dual plane configs. Otherwise, as
the SR watermark is not calculated for such configs, switching to non
VGA mode causes FIFO underrun and display flicker.
This fixes Korg Bug #14897.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes the driver not loading on older versions of VMware.
Signed-off-by: Peter Hanzel <hanzelpeter@gmail.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Re-order structure ttm_ref_object to remove 8 bytes of alignment padding
on 64 bit builds, so shrinking its size from 72 to 64 bytes allowing it
to fit into a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
First call drm_agp_acquire to check if agp has been acquired.
Second call drm_agp_info to fill in the info data struct, including aper_size.
Finally do the check to see if the aper_size makes sense.
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Fix warning by using %zu instead of %d for size_t
- Fix spelling mistake, "to" should be "too".
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes errors like:
> reserve_ram_pages_type failed 0x15b7a000-0x15b7b000, track 0x8, req 0x10
when a BO is moved between WC and UC areas.
Reported-by: Xavier Chantry <shiningxc@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
booting a Lenovo W500 with LVDS + DP outputs showed up a TODO we had
on our list, to pick a correct digital encoder block. The LVTMA
encoder requires the second digital encoder, all others can use any
encoder at all.
This fixes the digital encoder selection logic to enable LVDS/DP combos
to work okay.
V2: fix silly addition of connector dig_block and cleanup the other
places in the code that pick the encoder.
V3: rename to dig_encoder and clean up further - also fix
the picking algorithm.
tested on Lenovo W500 + desktop 3650 cards.
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the W500 we have UNIPHY routed to both DVI and DP, this seems
to always pick the DVI connector which means link training fails.
Switch to using active device to pick the connector, this seems
like it should be safe from a code review, and it fixes things
a bit more here.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds support for page flipping on Ironlake, which uses
different interrupt bits for triggering flip submit IRQs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-resolved for rebasing off of render power saving patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
Zhenyu noticed that the ironlake vblank enabling patch has one
issue that it will trigger vblank starting from irq postinstall,
this isn't necessary. This patch addresses this issue by only
adding the vblank into DEIER but mask them in DEIMR, so that it
won't trigger vblank interrupt at irq install.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Having missed the ENOMEM return via i915_gem_fault(), there are probably
other paths that I also missed. By not enabling NORETRY by default these
paths can run the shrinker and take memory from the system (but not from
our own inactive lists because our shrinker can not run whilst we hold
the struct mutex) and this may allow the system to survive a little longer
whilst our drivers consume all available memory.
References:
OOM killer unexpectedly called with kernel 2.6.32
http://bugzilla.kernel.org/show_bug.cgi?id=14933
v2: Pass gfp into page mapping.
v3: Use new read_cache_page_gfp() instead of open-coding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first page flip queued will replace the current front buffer, which
should have a 0 pending flip count. So at finish time we need to handle
that case (i.e. if the flip count is 0 *or* dec_and_test is 0 we need to
wake the waiters).
Also fix up an error path in the queue function and add some debug
output (only enabled with driver debugging).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (95 commits)
drm/radeon/kms: preface warning printk with driver name
drm/radeon/kms: drop unnecessary printks.
drm: fix regression in fb blank handling
drm/radeon/kms: make hibernate work on IGPs
drm/vmwgfx: Optimize memory footprint for DMA buffers.
drm/ttm: Allow system memory as a busy placement.
drm/ttm: Fix race condition in ttm_bo_delayed_delete (v3, final)
drm/nv50: prevent switching off SOR when in use for DVI-over-DP
drm/nv50: fail auxch transaction if reply count not what we expect
drm/nouveau: fix failure path if userspace specifies no valid memtypes
drm/nouveau: report LVDS as disconnected if lid closed
drm/radeon/kms: fix legacy get_engine/memory clock
drm/radeon/kms/atom: atom parser fixes
drm/radeon/kms: clean up atombios pll code
drm/radeon/kms: clean up pll struct
drm/radeon/kms/atom: fix crtc lock ordering
drm/radeon: r6xx/r7xx possible security issue, system ram access
drm/radeon/kms: r600/r700 don't test ib if ib initialization fails
drm/radeon/kms: Forbid creation of framebuffer with no valid GEM object
drm/radeon/kms: r600 handle irq vector ring overflow
...
Pineview doesn't has CXSR and need GTT-based hardware status page.
It fixes a X boot hung issue on Pinview since commit cfdf1f
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
so far vblank interrupt on ironlake is disabled, this would cause
bad gfx performance if userspace calls drm_wait_vblank. This patch
enables vblank interrupt on ironlake and follows vblank get/put
model.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This tries to fix CRT detect loop hang seen on some Ironlake form
factor, to clear up hotplug detect state before taking CRT detect
to make sure next hotplug detect cycle is consistent.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
commit 731b5a15a3
Author: James Simmons <jsimmons@infradead.org>
Date: Thu Oct 29 20:39:07 2009 +0000
drm/kms: properly handle fbdev blanking
uses DRM_MODE_DPMS_ON for FB_BLANK_NORMAL, but DRM_MODE_DPMS_ON
is actually for turning output on instead of blank.
This makes fb blank broken on my T61, it put LVDS on but leave
pipe disabled which made screen totally white or caused some
'burning' effect.
[airlied: James objects to this but at this point in 2.6.33,
I can't see a patch that will fix this properly like he wants coming
in time and otherwise this is a regression - proper fix for 2.6.34
hopefully.]
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the least invasive fix without migrating the radeon driver
to pm_ops from what I can see. We just always migrate VRAM objects
on IGPs for now and we can fix it up later to migrate depending
on STR vs STD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use VRAM whenever there is free space for DMA buffers,
but use system GMR memory if using VRAM would cause an eviction.
This significantly reduces the guest system memory usage for
VMs with a large amount of VRAM allocated.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to fix a vmwgfx memory usage bug.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next:
drm/nv50: prevent switching off SOR when in use for DVI-over-DP
drm/nv50: fail auxch transaction if reply count not what we expect
drm/nouveau: fix failure path if userspace specifies no valid memtypes
drm/nouveau: report LVDS as disconnected if lid closed
drm/nv50: prevent accidently turning off encoders we're actually using
drm/nv50: fix alignment of per-channel fifo cache
drm/nouveau: Evict buffers in VRAM before freeing sgdma
drm/nouveau: Acknowledge DMA_VTX_PROTECTION PGRAPH interrupts
drm/nouveau: fix thinko in nv04_instmem.c
drm/nouveau: fix a race condition in nouveau_dma_wait()
Resending this with Thomas Hellstrom's signoff for merging into 2.6.33
ttm_bo_delayed_delete has a race condition, because after we do:
kref_put(&nentry->list_kref, ttm_bo_release_list);
we are not holding the list lock and not holding any reference to
objects, and thus every bo in the list can be removed and freed at
this point.
However, we then use the next pointer we stored, which is not guaranteed
to be valid.
This was apparently the cause of some Nouveau oopses I experienced.
This patch rewrites the function so that it keeps the reference to nentry
until nentry itself is freed and we already got a reference to nentry->next.
v2 updated by me according to Thomas Hellstrom's feedback.
v3 proposed by Thomas Hellstrom. Commit comment updated by me.
Both updates fixed minor efficiency/style issues only and all three versions
should be correct.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Another hack because of us exposing each encoder block's function as
an encoder rather than exposing a single encoder that deals with them
all.
A proper fix will come, it's just rather invasive so this hack will
do until then.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to add the buffer to the list even if we fail, otherwise the
validate_fini() call won't unreserve + unreference the GEM object,
making TTM very unhappy.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Also adds a module option to ignore the status reported via ACPI, in case
we hit systems with broken ACPI.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix a bad shift in the post div.
Should fix fdo bug 26145
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only reset the reg block on the initial execute
table call; nested calls require the reg block not be
reset on each call. Also reset the fb window and
io mode. This matches the upstream parser behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- split pll adjust into a separate function
- use a union for SetPixelClock params
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add a new flag for fixed post div
- pull the pll flags into the struct
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch workaround a possible security issue which can allow
user to abuse drm on r6xx/r7xx hw to access any system ram memory.
This patch doesn't break userspace, it detect "valid" old use of
CB_COLOR[0-7]_FRAG & CB_COLOR[0-7]_TILE registers and overwritte
the address these registers are pointing to with the one of the
last color buffer. This workaround will work for old mesa &
xf86-video-ati and any old user which did use similar register
programming pattern as those (we expect that there is no others
user of those ioctl except possibly a malicious one). This patch
add a warning if it detects such usage, warning encourage people
to update their mesa & xf86-video-ati. New userspace will submit
proper relocation.
Fix for xf86-video-ati / mesa (this kernel patch is enough to
prevent abuse, fix for userspace are to set proper cs stream and
avoid kernel warning) :
http://cgit.freedesktop.org/xorg/driver/xf86-video-ati/commit/?id=95d63e408cc88b6934bec84a0b1ef94dfe8bee7bhttp://cgit.freedesktop.org/mesa/mesa/commit/?id=46dc6fd3ed5ef96cda53641a97bc68c3bc104a9f
Abusing this register to perform system ram memory is not easy,
here is outline on how it could be achieve. First attacker must
have access to the drm device and be able to submit command stream
throught cs ioctl. Then attacker must build a proper command stream
for r6xx/r7xx hw which will abuse the FRAG or TILE buffer to
overwrite the GPU GART which is in VRAM. To achieve so attacker
as to setup CB_COLOR[0-7]_FRAG or CB_COLOR[0-7]_TILE to point
to the GPU GART, then it has to find a way to write predictable
value into those buffer (with little cleverness i believe this
can be done but this is an hard task). Once attacker have such
program it can overwritte GPU GART to program GPU gart to point
anywhere in system memory. It then can reusse same method as he
used to reprogram GART to overwritte the system ram through the
GART mapping. In the process the attacker has to be carefull to
not overwritte any sensitive area of the GART table, like ring
or IB gart entry as it will more then likely lead to GPU lockup.
Bottom line is that i think it's very hard to use this flaw
to get system ram access but in theory one can achieve so.
Side note: I am not aware of anyone ever using the GPU as an
attack vector, nevertheless we take great care in the opensource
driver to try to detect and forbid malicious use of GPU. I don't
think the closed source driver are as cautious as we are.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If ib initialization failed don't try to test ib as it will result
in an oops (accessing NULL ib buffer ptr).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This will avoid oops if at later point the fb is use. Trying to create
a framebuffer with no valid GEM object is bogus and should be forbidden
as this patch does.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some rare case i faced an irq overflow quickly followed by
a GPU lockup (hard hang) this patch try to deal with irq vector
ring overflow, so far haven't been able to reproduce it with
the patch.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some rare case the wptr returned from the hw wasn't 0 and leaded
to trick r600_process_irq that their were irq to process. Add a
check to bail out if irq hasn't been initialized this will avoid
oops provoqued by the rare wptr != 0 on initialization.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
To avoid hw doing anythings after we disabled PCIE GART, fully
disable IRQ at suspend. Also cleanup a bit the ih structure
and process function.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
most of radeon_legacy_atom_set_surface() is taken care
of in atombios_set_base(), so remove the duplicate
setup and move the remaining bits (DISP_MERGE setup and
FP2 sync) to atombios_crtc.c where they are used.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Make it call the proper backend depending on the
GPU family. Right now r4xx cards with atombios modesetting
enabled were using the avivo crtc base code. This also
allows us to add support for new asics more easily.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
- add support for inline src params
- fix shift_left/shift_right and shl/shr ops
shift_* ops use inline src params, shl/r use full params
- fix mask op (uses inline params)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The first dword of PACKET3_3D_DRAW_IMMD maps to
SE_VTX_FMT so the vertex size is part of the draw
packet.
This patch fixes a possible case where you have a
command buffer that does not contain SE_VTX_FMT
register write, but does contain PACKET3_3D_DRAW_IMMD.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add missing vertex shader regs for r200.
fixed fdo bug 26061
agd5f: use official reg names
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The checks for CUBE and 3D textures were inverted.
fixes fdo bug 24159
agd5f: added comments for clarity.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Jesse Barnes