kmalloc can fail in rsi_register_rates_channels but memcpy still attempts
to write to channels. The patch replaces these calls with kmemdup and
passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fixes to spelling mistakes in various files in rsi folder.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a \b (backspace) character in the message that wasn't intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a block of code that is indented at the wrong level. Fix this
with extra tabbing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During wowlan regression tests, sometimes radio is not waking up for wowlan
packet in coex mode. This is because of power save is enabled by default
in case of coex mode greater than one. Hence, disable power save in coex
mode to avoid radio loss.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are redownloading the firmware after S4 restore and observed in
stress test that mac80211 sometimes gives power save request after
resume which causes the firmware in bad state. mac_ops_resumed flag
is added to skip that request until initialisation is done and Keeping
power save state is NONE.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At SDIO restore ieee80211_restart_hw() is getting called to restart all
MAC operations. This step is not required.
Returning 1 from mac80211_resume() will serve this purpose.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current approach of scanning, roaming delays are observed.
Firmware has support for back ground scanning. To get this advantage,
mac80211 hardware scan is implemented, which decides type of scan to
do based on connected state.
When station is in not connected, driver returns with special value 1
to trigger software scan in mac80211. In case of connected state,
background scan will be triggered.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/net/wireless/rsi/rsi_91x_mac80211.c:927:50: warning: address of
array 'key->key' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (vif->type == NL80211_IFTYPE_STATION && key->key &&
~~ ~~~~~^~~
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/136
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to multiple calls of add interface routine, vif is getting duplicated
and at certain instance, we are out of vifs, causing the driver to behave
abnormal.
Fix: Every vif has a unique mac-id, when we got a vif with same mac-id as
the previous id's, we will override the respective vif.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in rsi_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As wowlan enable flag did not set, while writing wowlan parameters to
card using rsi_send_vap_dynamic_update, which results firmware is unable to
set wowlan configurations. Hence, setting wowlan flag before sending
parameters.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the "poweroff" command is executed after wowlan enabled, we have
observed a system crash. In the system "poweroff" sequence, network-manager
is sent to inactive state by cleaning up the network interfaces, using
rsi_mac80211_remove_interface() and when driver tries to access those
network interfaces in rsi_wowlan_config() which was invoked by SDIO
shutdown, results in a crash. Added a NULL check before accessing the
network interfaces in rsi_wowlan_config().
Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function rsi_hal_key_config returns before reaching code at line
922 if (status), hence this code is structurally dead.
Fix this by storing the value returned by rsi_hal_load_key
into _status_ for its further evaluation and use.
Addresses-Coverity-ID: 1468409 ("Structurally dead code")
Fixes: 4fd6c4762f ("rsi: roaming enhancements")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently 5GHz gets advertised even for the device which supports
only 2.4Ghz band. This patch fixes the issue
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power save is by default enabled for WLAN and BT coex mode.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maximum number of supported aggregation subframes has been increased
to 8. This is the optimal number for the driver.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power save request should be sent on station interface. Virtual
interface which is connected should be preferred. This patch
resolves device not entering power save problem in certain
situations
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support roaming below changes are done:
* Station notify frame is send to firmware after sending assoc
request. This will avoid dropping of first EAPOL frame due to
delay in creation of station control block in firmware.
* Data queues are unblocked after sending station notify in open
mode, after configuring key in WEP mode, and after receiving
EAPOL4 confirm in WPA mode.
* Initial EAPOL frames priority is chaged to MGMT, rekey EAPOL
frames priority changed to VO.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some wowlan related code was outside CONFIG_PM flag which caused these
build errors. They are fixed by moving that code under CONFIG_PM flag.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unlike other power states, WoWLAN configuration does not come from
mac80211 for shutdown. Hence configuring the WoWLAN from shut down
callback it self. Remaining steps of disabling SDIO interrupts,
setting 'MMC_PM_KEEP_POWER' flag are same as other power states.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are disabling of interrupts from firmware in freeze handler.
Also setting power management capability KEEP_MMC_POWER to make
device wakeup for WoWLAN trigger.
At restore, we observed a device reset on some platforms. Hence
reloading of firmware and device initialization is performed.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WoWLAN is supported in RS9113 device through GPIO pin2.
wowlan config frame is internally sent to firmware in mac80211
suspend handler. Also beacon miss threshold and keep-alive time
values are increased to avoid un-necessary disconnection with AP.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add P2P_GO condition as well when handling BEACON_ENABLE
from mac80211. Also passing 'vif' for auto rate request.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
P2P Go condition is added wherever AP mode is there
in aggregation path.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP or P2P GO VAP is running, power save configuration should
be disallowed. To check interface type in power save configuration
'vif' parameters is passed.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data descriptor is updated to include vap_id. TX command frame
key config also updated to include vap_id.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parameter 'vif' is passed to inform_bss_status function to
check the type of vif and to get vap_id.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remain-on-channel and cancel-remain-on-channel are implemented
to support p2p listen phase.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA_OPMODE and AP_OPMODE macros are renamed to RSI_OPMODE_STA
and RSI_OPMODE_AP. New opmodes are added to this list for P2P
support. Mapping of mac80211 interface types to rsi interface
types are added.
Add and remove interface callbacks are handled for P2P mode.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds p2p supported parameters to mac80211 hw and
wiphy structures during mac80211 registration.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a missing unlock if rsi_find_sta() fails in
rsi_mac80211_ampdu_action() or if we hit the -EINVAL path in
rsi_mac80211_sta_add().
Fixes: 3528608f3a ("rsi: handle station connection in AP mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ieee80211_ops are not supposed to change at runtime. All functions
working with ieee80211_ops provided by <net/mac80211.h> work with
const ieee80211_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Station id should be set in load key frame configured to device.
For WEP mode, key is configured once from mac80211. This key is
saved and configured to device every time a station is connected.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame ampdu aggregation parameters is updated to
include sta_id for AP mode.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When sta_remove of mac80211 is called, driver iterates through
list of existing stations to get the station id. Then peer notify
is prepared and send to firmare.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Station structures are maintained in driver with required
fields. When mac80211 callback sta_add is called, driver
iterates through list of connected stations to check available
index and assigns station id which is important for further
communication to that station. Then peer notify frame is send
to firmware to inform the firmware about new station connection.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mac80211 config parameter BEACON_ENABLE is handled. When VAP
capabilities frame with AP mode is configured to firmware, beacon
events start coming to host at each PreTBTT. At this time, beacon
is taken from mac80211, descriptor is prepared and send to firmware.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove_interface callback of mac80211 is handled for AP mode.
Same is notified to firmware through vap_capabilities frame
with VAP status VAP_DELETE.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP mode is handled in add_interface callback of mac80211.
Also for AP mode, sending rx filter frame to disallow beacons
to host is added. Station structures are initialized to NULL.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP mode support is advertised to cfg80211. Necessary wiphy
parameters are initialized.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Provision is added for configuring RTS threshold by sending
vap dynamic update frame to firmware.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for U-APSD power save. Configuration
frame is downloaded to firmware with default settings and
support is advertised to mac80211
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements rfkill_poll handler. Also, necessary changes
are done in interface up and down handler to support rfkill
functionality.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Below regulatory changes are included this patch
* Country code is saved as it will be used in bgscan.
* Region codes are mapped according to RSI region codes.
* Radar flag settings are moved under the check if 5GHZ band
is enabled.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface is down it is better to stop all RX packets to
host. 0xffff will block all packets to host.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Aditya Pakki