Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
Based-on-patch-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
Based-on-patch-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make sure PCIe MPS settings are valid when we enumerate a new hierarchy.
[bhelgaas: changelog]
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
The current default of 20ms cause some devices, which are slow to
initialize, to not show up during the bus scanning. Change this to the
PCIe spec mandated 100ms and document this in the DT binding.
From PCIe base spec rev 3.0, chapter "6.6.1. Conventional Reset":
To allow components to perform internal initialization, system software
must wait a specified minimum period following the end of a Conventional
Reset of one or more devices before it is permitted to issue
Configuration Requests to those devices.
With a Downstream Port that does not support Link speeds greater than 5.0
GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The PCIe controller in HiSilicon Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add DT support for the almost-ECAM Hip06/Hip07 controllers.
[bhelgaas: drop dev->of_node test, driver name "hisi-pcie-almost-ecam"]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
The only way to call hisi_pcie_probe() is to match an entry in
hisi_pcie_of_match[], so match cannot be NULL.
Use of_device_get_match_data() to retrieve the soc_ops pointer. No
functional change intended.
[bhelgaas: use of_device_get_match_data(), changelog]
Based-on-suggestion-from: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The only way to call iproc_pcie_pltfm_probe() is to match an entry in
iproc_pcie_of_match_table[], so match cannot be NULL.
Use of_device_get_match_data() to retrieve the pcie->type. No functional
change intended.
Based-on-suggestion-from: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is a DT-only driver, so the only way to call rcar_pcie_probe() is to
match an entry in rcar_pcie_of_match[], so of_id cannot be NULL.
Furthermore, of_id->data can only be NULL if an rcar_pcie_of_match[] entry
has a NULL .data member. That's a driver defect, and we don't want to
return -EINVAL, which is easy to ignore. We'd rather take the NULL pointer
dereference so we notice the problem and fix it.
Use of_device_get_match_data() to retrieve the hw_init_fn pointer. No
functional change intended.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The "port" variable was allocated with devm_kzalloc() so if we free it with
kfree() it will be freed twice. Also I changed it to propogate the error
from devm_ioremap_resource() instead of returning -ENOMEM.
Fixes: c5d4603961 ("PCI: Add MCFG quirks for X-Gene host controller")
Also-posted-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
When CONFIG_PM_SLEEP is disabled, we get harmless build warnings:
host/pcie-rockchip.c:1267:12: error: 'rockchip_pcie_resume_noirq' defined but not used [-Werror=unused-function]
host/pcie-rockchip.c:1240:12: error: 'rockchip_pcie_suspend_noirq' defined but not used [-Werror=unused-function]
Marking both functions as __maybe_unused avoids the warning without the
need for #ifdef around them.
Fixes: 013dd3d5e1 ("PCI: rockchip: Add system PM support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Use readl_poll_timeout() instead of open-coding it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI core will write to the bridge window config multiple times while
they are enabled. This can lead to mbus failures like this:
mvebu_mbus: cannot add window '4:e8', conflicts with another window
mvebu-pcie mbus:pex@e0000000: Could not create MBus window at [mem 0xe0000000-0xe00fffff]: -22
For me this is happening during a hotplug cycle. The PCI core is not
changing the values, just writing them twice while active.
The patch addresses the general case of any change to an active window, but
not atomically. The code is slightly refactored so io and mem can share
more of the window logic.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The conversion to the new hotplug state machine introduced a regression
where a successful hotplug registration would be treated as an error,
effectively disabling the MSI driver forever.
Fix it by doing the proper check on the return value.
Fixes: 9c248f8896 ("PCI/xgene-msi: Convert to hotplug state machine")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Duc Dang <dhdang@apm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: stable@vger.kernel.org
The pci-thunder-pem driver was initially developed for cn88xx SoCs. The
cn81xx and cn83xx members of the same family of SoCs have a slightly
different configuration of interrupt resources in the PEM hardware, which
prevents the INTA legacy interrupt source from functioning with the current
driver.
There are two fixes required:
1) Don't fixup the PME interrupt on the newer SoCs as it already has the
proper value.
2) Report MSI-X Capability Table Size of 2 for the newer SoCs, so the core
MSI-X code doesn't inadvertently clobber the INTA machinery that happens to
reside immediately following the table.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rockchip's RC produces a 100MHz reference clock but there are two methods
for the PHY to generate it:
(1) Use the system PLL to generate a 100MHz clock. The PHY will relock
it, filter signal noise, and output the reference clock. ASPM L0s
works correctly, but circuit noise issues make it difficult to pass
the TX compatibility test.
(2) Share the SoC's 24MHZ crystal oscillator with the PHY and force the
PHY's PLL to generate 100MHz internally. In this case, exit from
ASPM L0s sometimes fails due to a design error in the RC receiver
circuit. Even if we use extended-synch, the PHY sometimes fails to
relock the bits from FTS, which will hang the system.
We want the flexibility to use both clocking methods, so add a DT property,
"aspm-no-l0s". If that's present, disable L0s to avoid the issues with
case (2).
[bhelgaas: changelog]
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
R-Car PCIe does not support hotplug so it is appropriate to treat the
absence of a PCIe card as an -ENODEV error.
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add system PM support for Rockchip's RC. For pre S3, the EP is configured
into D3 state which guarantees the link state should be in L1. So we could
send PME_Turn_Off message to the EP and wait for its ACK to make the link
state into L2 or L3 without the aux-supply. This could help save more
power which I think should be very important for mobile devices.
As note that there is a 5s timeout for RC to wait for the PMA_ACK after
sending PME_Turn_Off. Technically it should depend on the hierarchy of
devices but seems PCIe core framework doesn't handle the L2/3 for S3 at
all. So that means we should presume to set a default value for PME_ACK.
From the bug report[1], we could find a statement that Microsoft Windows
versions typically wait for 5 seconds. So we are prone to take 5s for this
timeout here.
[1] https://lists.launchpad.net/kernel-packages/msg123315.html
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Previously we checked for iATU unroll support by reading PCIE_ATU_VIEWPORT
even on platforms, e.g., Keystone, that do not have ATU ports. This can
cause bad behavior such as asynchronous external aborts:
OF: PCI: MEM 0x60000000..0x6fffffff -> 0x60000000
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
pgd = c0003000
[00000000] *pgd=80000800004003, *pmd=00000000
Internal error: : 1211 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-00009-g6ff59d2-dirty #7
Hardware name: Keystone
task: eb878000 task.stack: eb866000
PC is at dw_pcie_setup_rc+0x24/0x380
LR is at ks_pcie_host_init+0x10/0x170
Move the dw_pcie_iatu_unroll_enabled() check so we only call it on
platforms that do not use the ATU. These platforms supply their own
->rd_other_conf() and ->wr_other_conf() methods.
[bhelgaas: changelog]
Fixes: a0601a4705 ("PCI: designware: Add iATU Unroll feature")
Fixes: 416379f9eb ("PCI: designware: Check for iATU unroll support after initializing host")
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
CC: stable@vger.kernel.org # v4.9+
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
* pci/host-vmd:
PCI: vmd: Fix suspend handlers defined-but-not-used warning
PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU
PCI: vmd: Remove unnecessary pci_set_drvdata()
* pci/host-rockchip:
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
PCI: rockchip: Split out rockchip_cfg_atu()
PCI: rockchip: Clean up bit definitions for PCIE_RC_CONFIG_LCS
PCI: rockchip: Correct the use of FTS mask
PCI: rockchip: Remove the pointer to L1 substate cap
PCI: rockchip: Specify the link capability
PCI: rockchip: Fix negotiated lanes calculation
PCI: rockchip: Add Kconfig COMPILE_TEST
PCI: rockchip: Mark RC as common clock architecture
PCI: rockchip: Provide captured slot power limit and scale
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
* pci/host-rcar:
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
* pci/host-hv:
PCI: hv: Allocate physically contiguous hypercall params buffer
PCI: hv: Delete the device earlier from hbus->children for hot-remove
PCI: hv: Fix hv_pci_remove() for hot-remove
PCI: hv: Use the correct buffer size in new_pcichild_device()
PCI: hv: Make unnecessarily global IRQ masking functions static
* pci/host-altera:
PCI: altera: Remove redundant error message in altera_pcie_parse_dt()
PCI: altera: Use builtin_platform_driver() to simplify the code
PAXC and PAXCv2 buses do not support legacy IRQs so there is no reason to
even try and map them. Without a change like this, one cannot create VFs
on Nitro ports since legacy interrupts are checked as part of the PCI
device creation process. Testing on PAXC hardware showed that VFs are
properly created with only the change to not set pcie->map_irq, but just to
be safe the change in iproc_pcie_setup() will ensure that pdev_fixup_irq()
will not panic.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Add fallback compatibility string for the R-Car Gen 3 family. This is in
keeping with the both the existing fallback compatibility string for the
R-Car Gen 2 family and the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Improve readability by listing fallback compatibility strings after the
more-specific compatibility strings they provide a fallback for.
This does not affect run-time behaviour as it is the order in the DTB that
determines which compatibility string is used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move deassert of pm/aclk/pclk after phy_init() as we want to optimize the
logic of reset control and reuse rockchip_pcie_init_port() later which
should fully follow the cold boot procedure of ROM code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Split out a new function, rockchip_cfg_atu(), in order to re-configure the
ATU when missing these information after wakeup from S3.
[bhelgaas: add "dev" temporary, return 0 when known]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
PCIE_RC_CONFIG_LCS contains control and status bits specific to the PCIe
link. The layout for this register looks the same as the existing
PCI_EXP_LNKCTL and PCI_EXP_LNKSTA. So let's reuse them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We're trying to mask out bits[23:8] while retaining [32:24, 7:0], but we're
doing the inverse. That doesn't have too much effect, since we're setting
all the [23:8] bits to 1, and the other bits are only relevant for modes
we're currently not using. But we should get this right.
Fixes: ca19890840 ("PCI: rockchip: Fix wrong transmitted FTS count")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Per the errata of TRM, the RC can't support L1 substate, so remove the L1
substate cap as well as operation for PCIE_RC_CONFIG_L1_SUBSTATE_CTRL2.
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
rk3399 supports PCIe 2.x link speeds marginally at best, and on some
boards, the link won't train at 5 GT/s at all. Rather than sacrifice 500ms
waiting for training that will never happen, let's use the helper function,
of_pci_get_max_link_speed(), to get the max link speed from DT and specify
link capability.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calculation of negotiated lanes is wrong: it should be shifted by
PCIE_CORE_PL_CONF_LANE_SHIFT, but it is shifted by
PCIE_CORE_PL_CONF_LANE_MASK instead. Let's fix it.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow selection of the Rockchip driver for compile testing, even if we
aren't building for ARCH_ROCKCHIP.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The default value of common clock configuration is zero indicating
Rockchip's RC is using asynchronous clock architecture but actually we are
using common clock. This will confuse some EP drivers if they need some
different settings referring to this value.
Set the Common Clock Configuration bit in the Link Control Register.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If vpcie3v3 is available, we could provide these information via RC's
configure register to make EP able to know the power limit.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix the following warnings:
drivers/pci/host/vmd.c:731:12: warning: ‘vmd_suspend’ defined but not used [-Wunused-function]
static int vmd_suspend(struct device *dev)
^
drivers/pci/host/vmd.c:739:12: warning: ‘vmd_resume’ defined but not used [-Wunused-function]
static int vmd_resume(struct device *dev)
^
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
SRCU lets synchronize_srcu() depend on VMD-local RCU primitives, preventing
long delays from locking up RCU in other systems. VMD performs a
synchronize when removing a device, but will hit all IRQ lists if the
device uses all VMD vectors. This patch will not help VMD's RCU
synchronization, but will isolate the read side delays to the VMD
subsystem. Additionally, the use of SRCU in VMD's ISR will keep it
isolated from any other RCU waiters in the rest of the system.
Tested using concurrent FIO and NVMe resets:
[global]
rw=read
bs=4k
direct=1
ioengine=libaio
iodepth=32
norandommap
timeout=300
runtime=1000000000
[nvme0]
cpus_allowed=0-63
numjobs=8
filename=/dev/nvme0n1
[nvme1]
cpus_allowed=0-63
numjobs=8
filename=/dev/nvme1n1
while (true) do
for i in /sys/class/nvme/nvme*; do
echo "Resetting ${i##*/}"
echo 1 > $i/reset_controller;
sleep 5
done;
done
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The Tegra PCI host controller driver no longer relies on any of the 32-bit
ARM glue for PCI, so it can be enabled on 64-bit configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
The PCIe host controller found on Tegra X1 is very similar to its
predecessor on Tegra K1. A bug was introduced in the new revision that
is worked around by always enabling the performance counter, otherwise
accesses to configuration space will block for a number of seconds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Tegra210's PCIe controller has a bug that requires the PCA (performance
counter) feature to be enabled. If this isn't done, accesses to device
configuration space will hang the chip for tens of seconds. Implement the
workaround.
Based on commit 514e19138af2 ("pci: tegra: implement PCA enable
workaround") from U-Boot by Stephen Warren <swarren@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Tegra is one of the remaining platforms that still use the traditional
pci_common_init_dev() interface for probing PCI host bridges.
This demonstrates how to convert it to the pci_register_host interface I
just added in a previous patch. This leads to a more linear probe sequence
that can handle errors better because we avoid callbacks into the driver,
and it makes the driver architecture independent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull the register resource lookup out of thunder_pem_init() so we can
easily add a corresponding lookup using ACPI. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
hv_do_hypercall() assumes that we pass a segment from a physically
contiguous buffer. A buffer allocated on the stack may not work if
CONFIG_VMAP_STACK=y is set.
Use kmalloc() to allocate this buffer.
Reported-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
In the code to handle PAXB v2 based MSI steering, the logic aligns the MSI
register address to the size of supported inbound mapping range. This is
incorrect since it rounds "up" the starting address to the next aligned
address, but what we want is the starting address to be rounded "down" to
the aligned address.
This patch fixes the issue and allows MSI writes to be properly steered to
the GIC.
Fixes: 4b073155fbd3 ("PCI: iproc: Add support for the next-gen PAXB controller")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the MSM8996/APQ8096 PCIe controller. MSM8996 supports Gen
1/2, one lane, 3 PCIe root complexes with support for MSI and legacy
interrupts, and it conforms to PCI Express Base 2.1 specification.
Add a post_init callback to qcom_pcie_ops, as the PCIe pipe clocks are only
setup after the phy is powered on. It also adds an ltssm_enable callback
as it is very much different from other supported SoCs in the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add support for the next generation of the iProc PAXB host controller, used
in Stingray.
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Hardware that supports only 32-bit config writes is not spec-compliant.
For example, if software performs a 16-bit write, we must do a 32-bit read,
merge in the 16 bits we intend to write, followed by a 32-bit write. If
the 16 bits we *don't* intend to write happen to have any RW1C (write-one-
to-clear) bits set, we just inadvertently cleared something we shouldn't
have.
Add a rate-limited warning when we do sub-32 bit config writes. Remove
similar probe-time warnings from some of the affected host bridge drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enthusiastically-Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com> # rockchip
Acked-by: Thierry Reding <treding@nvidia.com>
Add support for inbound DMA mapping. The range of the inbound mapping is
configured by the optional device tree property 'dma-ranges'.
While inbound mapping is done automatically in the ASIC on most iProc-based
SoCs, newer ASICs (e.g., Stingray) require inbound mapping to be configured
explicitly in software.
[bhelgaas: fold in fixes to avoid 32-bit division in iproc_pcie_ib_write()
and uninitialized return value in iproc_pcie_setup_ib() from Arnd Bergmann
<arnd@arndb.de>]
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Improve the iProc PCIe outbound mapping code by making it more generic and
removing redundant device tree properties 'brcm,pcie-ob-window-size' and
'brcm,pcie-ob-oarr-size'. The driver is still backward compatible to
device tree binaries with the two properties specified.
The driver now automatically configures the correct mapping window size and
number of mapping windows based on the value of device tree property
'ranges' and the capability of of the iProc PCIe controller.
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Add support for the second generation of the iProc PCIe PAXC host
controller.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
After we send a PCI_EJECTION_COMPLETE message to the host, the host will
immediately send us a PCI_BUS_RELATIONS message with
relations->device_count == 0, so pci_devices_present_work(), running on
another thread, can find the being-ejected device, mark the
hpdev->reported_missing to true, and run list_move_tail()/list_del() for
the device -- this races hv_eject_device_work() -> list_del().
Move the list_del() in hv_eject_device_work() to an earlier place, i.e.,
before we send PCI_EJECTION_COMPLETE, so later the
pci_devices_present_work() can't see the device.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
1. We don't really need such a big on-stack buffer when sending the
teardown_packet: vmbus_sendpacket() here only uses sizeof(struct
pci_message).
2. In the hot-remove case (PCI_EJECT), after we send PCI_EJECTION_COMPLETE
to the host, the host will send a RESCIND_CHANNEL message to us and the
host won't access the per-channel ringbuffer any longer, so we needn't send
PCI_RESOURCES_RELEASED/PCI_BUS_D0EXIT to the host, and we shouldn't expect
the host's completion message of PCI_BUS_D0EXIT, which will never come.
3. We should send PCI_BUS_D0EXIT after hv_send_resources_released().
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
We don't really need such a big on-stack buffer. vmbus_sendpacket() here
only uses sizeof(struct pci_child_message).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
I returned to Synopsys and so I am sending this patch to update the email
address of the pcie-designware-plat author.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During enumeration with multi-function EP devices, access to the
configuration space of a non-existent function results in an unsupported
request being returned as expected. By default the PAXB-based iProc PCIe
controller forwards this as an APB error to the host system and that causes
an exception, which is undesired.
Disable this undesired behaviour and let the kernel PCI stack deal with an
access to the non-existent function, in which case a vendor ID of 0xffff is
returned and handled gracefully.
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
The iProc PCIe driver is currently using type IPROC_PCIE_PAXB for the
following SoCs: NS, NSP, Cygnus, NS2, and Pegasus. In fact, the BCMA-based
NS uses a legacy PAXB controller that is slightly different from the PAXB
controller used in the rest of SoCs, e.g., some registers are missing and
it does not require software configuration of outbound/inbound address
mapping.
Add a new type, IPROC_PCIE_PAXB_BCMA, to allow us to properly support the
BCMA-based NS along with other iProc-based SoCs going forward.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
During initialization, the current iProc PCIe host driver resets PAXC and
the downstream internal endpoint device that PAXC connects to. If the
endpoint device is already loaded with firmware and has started running
from the bootloader stage, this downstream reset causes the endpoint device
to stop working.
Signed-off-by: Ray Jui <raj.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
As the number of iProc PCIe core registers starts to grow and differ
between different revisions of the iProc PCIe controllers, the
current way of populating each individual unsupported register with
value 'IPROC_PCIE_REG_INVALID' with a table entry has become a bit
messy and is difficult to scale up in the future.
Improve the current driver by populating the invalid entries with code
instead of through individual table entries. This helps to avoid a
significant number of invalid table entries when support for the next
revision of the iProc controller is added.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Add support for the LS1046a PCIe controller. This device has a different
LUT_DBG offset, so add "lut_dbg" to ls_pcie_drvdata to
describe this difference.
[bhelgaas: changelog, remove now-unused PCIE_LUT_DBG]
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver core clears the driver data to NULL after device_release or on
probe failure. Thus, it is not needed to manually clear the device driver
data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
There is an error message from devm_ioremap_resource() already, so remove
the dev_err() call to avoid redundant error messages.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is an error message from devm_ioremap_resource() already, so remove
the dev_err() call to avoid redundant error messages.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is an error message from devm_ioremap_resource() already, so remove
the dev_err() call to avoid redundant error messages.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pm_rst, aclk_rst, pclk_rst was controlled by ROM code so the software
wasn't needed to control it again in theory. But it didn't work properly,
so we do need to do it again and add enough delay between the assert of
pm_rst and the deassert of pm_rst. The Soc intergrated with this
controller, rk3399, is still under MP test internally, so the backward
compatibility won't be a big deal.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
dw_pcie_iatu_unroll_enabled() reads a dbi_base register. Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init. Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.
Fixes: a0601a4705 ("PCI: designware: Add iATU Unroll feature")
Tested-by: James Le Cuirot <chewi@gentoo.org>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Olof Johansson <olof@lixom.net>
Make hv_irq_mask() and hv_irq_unmask() static as they are only used in
pci-hyperv.c
This fixes a sparse warning.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Although I am leaving Synopsys, I would like to keep working with the linux
kernel community and help in what you might find useful. For that I am
sending this patch to change my contact e-mail.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit fefe6733e5 ("PCI: layerscape: Move struct pcie_port setup
to probe function") changed the init ordering of the pcie structure,
but started to use the pcie->drvdata field before initializing it.
Mayhem follows.
Fix this by moving the drvdata assignment right before the first use.
Tested on LS2085a.
Fixes: efe6733e516 ("PCI: layerscape: Move struct pcie_port setup to probe function")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Body of an "if" statement wasn't indented. Add a tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Include the PCIE_HIP06_CTRL_OFF block base in the PCIE_SYS_STATE4 register
address so reads of PCIE_SYS_STATE4 don't have to mention both. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The xilinx-nwl driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
xilinx_pcie_assign_msi() doesn't use the struct xilinx_pcie_port pointer
passed to it, so remove the argument completely. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The xilinx driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pass the struct xgene_pcie_port pointer, not addresses, to setup functions.
This enables future simplifications. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The xgene driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The tegra driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The tegra_pcie_phy_disable() path called pads_writel() with arguments in
the wrong order. Swap them to be the "value, offset" order expected by
pads_writel().
Fixes: 6fe7c187e0 ("PCI: tegra: Support per-lane PHYs")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
CC: stable@vger.kernel.org # v4.7+
The rockchip driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The DRV_NAME macro is only used once, so there's no real advantage to
having the macro at all. Remove it and use the "rcar-pcie" name directly
in the struct platform_driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
rcar_pcie_get_resources() doesn't use the platform_device pointer passed to
it, so remove it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The rcar driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Remove the struct qcom_pcie.dev member, which is a duplicate of the generic
pp.dev member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the struct qcom_pcie.dbi member, which is a duplicate of the generic
pp.dbi_base member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The qcom driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the existing "np" pointer instead of looking up dev->of_node again. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ls_add_pcie_port() doesn't use the platform_device pointer passed to it, so
remove it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Do the basic pcie_port setup in the probe function for consistency with
other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the struct ls_pcie.dbi member, which is a duplicate of the generic
pp.dbi_base member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The layerscape driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of passing ks_pcie->va_app_base to DBI mode functions,
pass the struct keystone_pcie. This will allow them to use register
accessors. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of passing the application register base to IRQ functions,
pass the struct keystone_pcie. This will allow them to use register
accessors. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dw_pcie_readl_rc() and dw_pcie_writel_rc() interfaces already add in
pp->dbi_base, so use those instead of doing it ourselves in the keystone
driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We know where the PCIe capability lives in the host bridge's config space;
in fact, we already hard-coded the offset of the Link Control 2 register.
The hard-coded Link Control 2 offset was 0xdc. Link Control 2 is at offset
0x30 into the PCIe capability, so the capability itself must be at
0xdc - 0x30 = 0xac.
Hard-code the PCIe capability offset, which means we don't have to search
for it and we can use the standard definitions for registers within the
capability.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The callers never pass a null "pcie" pointer (they check for kzalloc
failure), so we don't need to check here. The bus driver should never call
the probe function with a null ->dev pointer, so we don't need to check
that either. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Validate iproc_pcie->base for BCMA devices just like we already do for
platform devices in iproc_pcie_pltfm_probe(). No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the drvdata pointer at the end of probe function for consistency with
other drivers. We don't need the drvdata until after the probe completes,
and we don't need it at all if the probe fails. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dw_pcie_readl_rc() and dw_pcie_writel_rc() interfaces already add in
pp->dbi_base, so use those instead of doing it ourselves in the imx6
driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pass the struct imx6_pcie pointer, not dbi_base address, to PHY accessors.
This enables future simplifications. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"np" and "node" are redundant copies of the of_node pointer. Remove "np"
and use "node" instead. Replace the "fsl,max-link-speed" use with "node"
as well. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dw_pcie_readl_rc() and dw_pcie_writel_rc() interfaces already add in
pp->dbi_base, so use those instead of doing it ourselves in the hisi
driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the struct hisi_pcie.reg_base member, which is a duplicate of the
generic pp.dbi_base member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most struct hisi_pcie pointers are already called "hisi_pcie". Change
the rest of them to match. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The hisi driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most struct exynos_pcie pointers are already called "exynos_pcie". Change
the rest of them to match. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The register accessors are not performance critical and are small enough
that the compiler can inline them itself if it makes sense.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Do the basic pcie_port setup in the probe function for consistency with
other drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dw_pcie_readl_rc() and dw_pcie_writel_rc() interfaces already add in
pp->dbi_base, so use those instead of doing it ourselves in the dra7xx
driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the drvdata pointer at the end of probe function for consistency with
other drivers. We don't need the drvdata until after the probe completes,
and we don't need it at all if the probe fails. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The DesignWare core already stores the struct device pointer in struct
pcie_port. Remove the redundant copy from struct dra7xx_pcie.dev. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add comments about the Device Tree source of resources. No functional
change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Remove artpec6_pcie_link_up(); the generic dw_pcie_link_up() does the same
thing, so we don't need a device-specific version.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
The dw_pcie_readl_rc() and dw_pcie_writel_rc() interfaces already add in
pp->dbi_base, so use those instead of doing it ourselves in the armada8k
driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
The artpec6 driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reorder the device-specific struct to put the DesignWare generic struct
pcie_port first. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The dw_pcie_readl_rc() and dw_pcie_writel_rc() interfaces already add in
pp->dbi_base, so use those instead of doing it ourselves in the armada8k
driver. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The struct armada8k_pcie.base pointer is always a constant offset from
struct pcie_port.dbi_base. Encode that offset in the register macros so we
don't need to maintain the armada8k_pcie.base pointer. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a local "base" pointer, as is done for other uses, to simplify a
subsequent patch. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The armada driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
TLP_CFG_DW1() was only used with altera->root_bus_nr and RP_DEVFN, so
encode that directly into the macro so we don't have to clutter the uses
with the TLP_REQ_ID() usage. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All TLP_CFG_DW0() uses follow the same pattern based on the root bus
number, so pull that into the macro itself to declutter the users. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
devm_ioremap_resource() fails gracefully when given a NULL resource
pointer, so we don't need to check separately for failure from
platform_get_resource_byname(). Remove the redundant check.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The altera driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aardvark driver never uses the platform drvdata pointer, so don't
bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For consistency with other drivers, use the struct device pointer from
struct pcie_port whenever possible instead of relying on the
platform_device pointer. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only interfaces used from outside the driver, e.g., those called by the
DesignWare core, need to accept pointers to the generic struct pcie_port.
Internal interfaces can accept pointers to the device-specific struct,
which makes them more straightforward. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The designware-plat driver never uses the platform drvdata pointer, so
don't bother setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the struct dw_plat_pcie.mem_base member, which is only used as a
temporary. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Swap order of dw_pcie_readl_unroll() arguments to match the "dev, pos, val"
order used by pci_write_config_word() and other drivers. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The register accessors are not performance critical and small enough that
the compiler can inline them itself if it makes sense.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export dw_pcie_readl_rc() and dw_pcie_writel_rc(). Many other drivers can
use these instead of implementing their own versions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Swap order of dw_pcie_writel_rc() arguments to match the "dev, pos, val"
order used by pci_write_config_word() and other drivers. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The struct pcie_host_ops.readl_rc() and .writel_rc() function pointers
allow a driver to override the default DesignWare register accessors.
Make the signature of the override functions the same as the default
accessors. This makes the default dw_pcie_readl_rc() and the corresponding
override more structurally similar: both will compute the final register
address with "pp->dbi_base + reg". Previously dw_pcie_readl_rc() computed
the address and passed it to the override.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_readl_unroll() and dw_pcie_writel_unroll() duplicate what
dw_pcie_readl_rc() and dw_pcie_writel_rc() already do, so call them
directly.
[bhelgaas: reworked into patch series]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Rename dw_pcie_valid_config() to dw_pcie_valid_device() and use the result
directly as a boolean value instead of testing against 0. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-vmd:
x86/PCI: VMD: Move VMD driver to drivers/pci/host
x86/PCI: VMD: Synchronize with RCU freeing MSI IRQ descs
x86/PCI: VMD: Eliminate index member from IRQ list
x86/PCI: VMD: Eliminate vmd_vector member from list type
x86/PCI: VMD: Convert to use pci_alloc_irq_vectors() API
x86/PCI: VMD: Allocate IRQ lists with correct MSI-X count
PCI: Use positive flags in pci_alloc_irq_vectors()
PCI: Update "pci=resource_alignment" documentation
Conflicts:
drivers/pci/host/Kconfig
drivers/pci/host/Makefile
* pci/host-aardvark:
PCI: aardvark: Remove redundant dev_err call in advk_pcie_probe()
* pci/host-altera:
PCI: altera: Remove redundant platform_get_resource() return value check
PCI: altera: Move retrain from fixup to altera_pcie_host_init()
PCI: altera: Rework config accessors for use without a struct pci_bus
PCI: altera: Poll for link training status after retraining the link
* pci/host-artpec:
PCI: artpec6: Drop __init from artpec6_add_pcie_port()
* pci/host-designware:
PCI: designware: Remove redundant platform_get_resource() return value check
PCI: designware: Exchange viewport of `MEMORYs' and `CFGs/IOs'
PCI: designware: Keep viewport fixed for IO transaction if num_viewport > 2
PCI: designware: Check LTSSM training bit before deciding link is up
PCI: designware: Add iATU Unroll feature
PCI: designware: Wait for iATU enable
PCI: designware: Move link wait definitions to .c file
PCI: designware: Return data directly from dw_pcie_readl_rc()
* pci/host-hv:
PCI: hv: Handle hv_pci_generic_compl() error case
PCI: hv: Handle vmbus_sendpacket() failure in hv_compose_msi_msg()
PCI: hv: Remove the unused 'wrk' in struct hv_pcibus_device
PCI: hv: Use pci_function_description[0] in struct definitions
PCI: hv: Use zero-length array in struct pci_packet
PCI: hv: Use list_move_tail() instead of list_del() + list_add_tail()
* pci/host-keystone:
PCI: keystone: Propagate request_irq() failure
* pci/host-rcar:
PCI: rcar: Try increasing PCIe link speed to 5 GT/s at boot
PCI: rcar: Fix some checkpatch warnings
PCI: rcar: Add multi-MSI support
PCI: rcar: Don't disable/unprepare clocks on prepare/enable failure
PCI: rcar: Consolidate register space lookup and ioremap
* pci/host-rockchip:
PCI: rockchip: Fix wrong transmitted FTS count
PCI: rockchip: Improve the deassert sequence of four reset pins
PCI: rockchip: Increase the Max Credit update interval
PCI: rockchip: Add Rockchip PCIe controller support
dt-bindings: PCI: rockchip: Add DT bindings for Rockchip PCIe controller
* pci/host-tegra:
PCI: tegra: Use of_device_get_match_data()
PCI: tegra: Remove redundant _data suffix
* pci/host-xilinx:
microblaze/PCI: Add multidomain support for procfs
PCI: xilinx: Dispose of MSI virtual IRQ
PCI: xilinx: Clear correct MSI set bit
PCI: xilinx: Clear interrupt register for invalid interrupt
PCI: xilinx: Keep both legacy and MSI interrupt domain references
PCI: xilinx-nwl: Enable all MSI interrupts using MSI mask
PCI: xilinx-nwl: Expand error logging
Conflicts:
drivers/pci/host/pcie-xilinx.c
Move the driver source and Kconfig to the PCI host bridge drivers directory
and move the config option to a more appropriate sub-menu instead of
occupying the top-level location.
Update the Kconfig option with the X86_64 dependency that was implicitly
included from the previous location, and add information about the module
name when built as a loadable module.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jon Derrick <jonathan.derrick@intel.com>
If the expected number of FTS aren't received by RC when exiting from L0s,
the LTSSM will fall into recover state, which means it will need to send TS
for retraining which makes the latency of exiting from L0s a little longer
than expected. This issue is caused by an incorrect reset value of FTS
count on PLC1 register (offset 0x4). The expected value for Gen1/2 should
be more than 240 and we may leave a little margin here. Fix this before
starting Gen1 training which will make TS1 contain the correct FTS count.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per TRM, we need to deassert the four reset pins simultaneously. Currently
the reset framework doesn't support that so we did it one by one. It seems
no side effect found but it does impact the state machine of controller, so
sometimes the change speed bit is not set when sending training sequence
from recover state. After the silicon RTL review from SoC guys, we don't
need to do the sequence recommended by TRM, and could just move the
deassert of mgmt_sticky_rst to the first place.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Increase the likelihood of link state to automatically go to L1 and save
some power.
The default credit update interval of 7.5 us results in the rootport
sending UpdateFC-P and UpdateFC-NP packets too often, thus resulting in the
link never going to L1, and always staying in L0/L0s. The value 24 us was
chosen after some experiments and peeking over the PCIe bus to see that we
do enter L1 substate when there is not enough traffic on the PCIe bus.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
The PCIe link speed is initially set to 2.5 GT/s. Try to increase the link
speed to 5 GT/s.
Based on original patch by Grigory Kletsko
<grigory.kletsko@cogentembedded.com>.
[bhelgaas: remove "Trying speed up" message, remove unused SPCHG]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* pci/virtualization:
PCI: xilinx: Relax device number checking to allow SR-IOV
PCI: designware: Relax device number checking to allow SR-IOV
PCI: altera: Relax device number checking to allow SR-IOV
PCI: Check for pci_setup_device() failure in pci_iov_add_virtfn()
PCI: Mark Atheros AR9580 to avoid bus reset
artpec6_add_pcie_port() is called from artpec6_pcie_probe(), which is not
marked __init. It is wrong to call an __init function from a non-__init
one, so remove __init from artpec6_add_pcie_port().
[bhelgaas: changelog]
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The R-Car PCIe driver causes 13 warnings from scripts/checkpatch.pl --
let's fix at least 10 easier ones:
- line over 80 characters;
- blank line missing after declarations;
- statements not starting on a tabstop.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Implement the MSI .setup_irqs() method which enables allocation of several
MSIs at once.
[Sergei Shtylyov: removed unrelated/unneeded changes, fixed too long lines,
reordered the variable declarations, reworded the summary/description.]
Signed-off-by: Grigory Kletsko <grigory.kletsko@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Dispose of virtual IRQ being created for MSI interrupts.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Kernel provides virtual IRQ number at teardown. Get hwirq number from
virtual IRQ and clear correct MSI set bit.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The interrupt decode register is not being cleared if an invalid interrupt
arises. Clear the decode register in this case.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
When built with MSI support, the legacy domain reference was being
overwritten with MSI.
Create two separate domains for MSI and legacy interrupts.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The current mask enables and allows only one MSI interrupt on each MSI
line. Enable all MSI interrupts, which will also support Endpoints with
multi-MSI support.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If clk_prepare_enable() fails, we must not call clk_disable_unprepare() in
the error path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
devm_ioremap_resource() fails gracefully when given a NULL resource
pointer, so we don't need to check separately for failure from
platform_get_resource_byname(). Remove the redundant check.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we used a PCI early fixup to initiate a link retrain on Altera
devices. But Altera PCIe IP can be configured as either a Root Port or an
Endpoint, and they might have same vendor ID, so the fixup would be run for
both.
We only want to initiate a link retrain for Altera Root Port devices, not
for Endpoints, so move the link retrain functionality from the fixup to
altera_pcie_host_init().
[bhelgaas: changelog]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we only allowed device 0 to be directly attached to the root
port. But SR-IOV devices may use non-zero device numbers for VFs.
Remove the restriction that only device 0 may be attached to a root port.
[bhelgaas: changelog]
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we only allowed device 0 to be directly attached to the root
port. But SR-IOV devices may use non-zero device numbers for VFs.
Remove the restriction that only device 0 may be attached to a root port.
[bhelgaas: changelog]
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Previously we only allowed device 0 to be directly attached to the root
port. But SR-IOV devices may use non-zero device numbers for VFs.
Remove the restriction that only device 0 may be attached to a root port.
[bhelgaas: changelog]
Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI tegra host bridge driver adds the PCI IO resource retrieved from
firmware to the host bridge resource windows even if the
pci_remap_iospace() call fails; this is an actual bug in that the PCI host
bridge would consider the PCI IO resource valid (and possibly assign it to
downstream devices) even if the kernel was not able to map the PCI host
bridge memory address driving IO cycle to the CPU virtual address space (ie
pci_remap_iospace() failures).
Add the PCI host bridge driver pci_remap_iospace() failure path and do not
add the corresponding PCI host bridge PCI IO resources retrieved through
firmware when the pci_remap_iospace() function call fails, fixing the
issue.
Fixes: e6e9f471f5 ("PCI: tegra: Use generic pci_remap_iospace() rather than ARM32-specific one")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thierry Reding <treding@nvidia.com>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI common host bridge driver does not remove the PCI IO resource from
the host bridge resource windows if the pci_remap_iospace() call fails;
this is an actual bug in that the PCI host bridge would consider the PCI IO
resource valid (and possibly assign it to downstream devices) even if the
kernel was not able to map the PCI host bridge memory address driving IO
cycle to the CPU virtual address space (ie pci_remap_iospace() failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: 4e64dbe226 ("PCI: generic: Expose pci_host_common_probe() for use by other drivers")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI rcar host bridge driver does not remove the PCI IO resource from
the host bridge resource windows if the pci_remap_iospace() call fails;
this is an actual bug in that the PCI host bridge would consider the PCI IO
resource valid (and possibly assign it to downstream devices) even if the
kernel was not able to map the PCI host bridge memory address driving IO
cycle to the CPU virtual address space (ie pci_remap_iospace() failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: 5d2917d469 ("PCI: rcar: Convert to DT resource parsing API")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Phil Edworthy <phil.edworthy@renesas.com>
CC: Simon Horman <horms+renesas@verge.net.au>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI versatile host bridge driver does not remove the PCI IO resource
from the host bridge resource windows if the pci_remap_iospace() call
fails; this is an actual bug in that the PCI host bridge would consider the
PCI IO resource valid (and possibly assign it to downstream devices) even
if the kernel was not able to map the PCI host bridge memory address
driving IO cycle to the CPU virtual address space (ie pci_remap_iospace()
failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: b7e78170ef ("PCI: versatile: Add DT-based ARM Versatile PB PCIe host driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Rob Herring <robh@kernel.org>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridges memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI designware host bridge driver does not remove the PCI IO resource
from the host bridge resource windows if the pci_remap_iospace() call
fails; this is an actual bug in that the PCI host bridge would consider the
PCI IO resource valid (and possibly assign it to downstream devices) even
if the kernel was not able to map the PCI host bridge memory address
driving IO cycle to the CPU virtual address space (ie pci_remap_iospace()
failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: cbce790059 ("PCI: designware: Make driver arch-agnostic")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
On ARM/ARM64 architectures, PCI IO ports are emulated through memory mapped
IO, by reserving a chunk of virtual address space starting at PCI_IOBASE
and by mapping the PCI host bridge's memory address space driving PCI IO
cycles to it.
PCI host bridge drivers that enable downstream PCI IO cycles map the host
bridge memory address responding to PCI IO cycles to the fixed virtual
address space through the pci_remap_iospace() API.
This means that if the pci_remap_iospace() function fails, the
corresponding host bridge PCI IO resource must be considered invalid, in
that there is no way for the kernel to actually drive PCI IO transactions
if the memory addresses responding to PCI IO cycles cannot be mapped into
the CPU virtual address space.
The PCI aardvark host bridge driver does not remove the PCI IO resource
from the host bridge resource windows if the pci_remap_iospace() call
fails; this is an actual bug in that the PCI host bridge would consider the
PCI IO resource valid (and possibly assign it to downstream devices) even
if the kernel was not able to map the PCI host bridge memory address
driving IO cycle to the CPU virtual address space (ie pci_remap_iospace()
failures).
Fix the PCI host bridge driver pci_remap_iospace() failure path, by
destroying the PCI host bridge PCI IO resources retrieved through firmware
when the pci_remap_iospace() function call fails, therefore preventing the
kernel from adding the respective PCI IO resource to the list of PCI host
bridge valid resources, fixing the issue.
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
'completion_status' is used in some places, e.g.,
hv_pci_protocol_negotiation(), so we should make sure it's initialized in
error case too, though the error is unlikely here.
[bhelgaas: fix changelog typo and nearby whitespace]
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: KY Srinivasan <kys@microsoft.com>
CC: Jake Oshins <jakeo@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
Handle vmbus_sendpacket() failure in hv_compose_msi_msg().
I happened to find this when reading the code. I didn't get a real issue
however.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: KY Srinivasan <kys@microsoft.com>
CC: Jake Oshins <jakeo@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
The 2 structs can use a zero-length array here, because dynamic memory of
the correct size is allocated in hv_pci_devices_present() and we don't need
this extra element.
No functional change.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: KY Srinivasan <kys@microsoft.com>
CC: Jake Oshins <jakeo@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
Use zero-length array in struct pci_packet and rename struct pci_message's
field "message_type" to "type". This makes the code more readable.
No functionality change.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: KY Srinivasan <kys@microsoft.com>
CC: Jake Oshins <jakeo@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
Add support for the Rockchip PCIe controller found on RK3399 SoC platform.
[bhelgaas: fold in Brian's rockchip_pcie_client_irq_handler() OR fix, other
fixes and cleanups from Guenter Roeck <linux@roeck-us.net> and me,
uninitialized variable fix from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Rework configs accessors so a future patch can use them in _probe() with
struct altera_pcie instead of struct pci_bus.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_XILINX_NWL
drivers/pci/host/Kconfig: bool "NWL PCIe Core"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Explicitly disallow driver unbind, since that doesn't have a sensible use
case anyway, and it allows us to drop the ".remove" code for non-modular
drivers. Delete several functions only used by the remove function.
Note that for non-modular code, builtin_platform_driver() uses the same
init level priority as module_platform_driver(), so this doesn't change
init ordering.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_XILINX
drivers/pci/host/Kconfig: bool "Xilinx AXI PCIe host bridge support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, builtin_platform_driver() uses the same
init level priority as module_platform_driver(), so this doesn't change
init ordering.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_QCOM
drivers/pci/host/Kconfig: bool "Qualcomm PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
builtin_platform_driver() uses the same init level priority as
module_platform_driver(), so this doesn't change init ordering.
Explicitly disallow driver unbind, since that doesn't have a sensible use
case anyway, and it allows us to drop the ".remove" code for non-modular
drivers.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_DRA7XX
drivers/pci/host/Kconfig: bool "TI DRA7xx PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
builtin_platform_driver_probe() uses the same init level priority as
module_platform_driver_probe(), so this doesn't change init ordering.
Explicitly disallow driver unbind, since that doesn't have a sensible use
case anyway, and it allows us to drop the ".remove" code for non-modular
drivers.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_COMMON
drivers/pci/host/Kconfig: bool
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Will Deacon <will.deacon@arm.com>
devm_ioremap_resource() fails gracefully when given a NULL resource
pointer, so we don't need to check separately for failure from
platform_get_resource_byname(). Remove the redundant check.
[bhelgaas: changelog]
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When we have only two view ports in a DesignWare PCIe platform, iatu0
is used for both CFG and IO accesses. When CFGs are sent to peripherals
(e.g., lspci), iatu0 frequently switches between CFG and IO.
For such scenarios, a MEMORY might be sent as an IOs by mistake.
Considering the following configurations:
MEMORY -> BASE_ADDR: 0xb4100000, LIMIT: 0xb4100FFF, TYPE=mem
CFG -> BASE_ADDR: 0xb4000000, LIMIT: 0xb4000FFF, TYPE=cfg
IO -> BASE_ADDR: 0xFFFFFFFF, LIMIT: 0xFFFFFFFE, TYPE=io
Suppose PCIe has just completed a CFG access. To switch back to IO, it
sets the BASE_ADDR to 0xFFFFFFFF, LIMIT 0xFFFFFFFE and TYPE to IO. When
another CFG comes, the BASE_ADDR is set to 0xb4000000 to switch to CFG. At
this moment, a MEMORY access shows up, since it matches with iatu0 (due to
0xb4000000 <= MEMORY BASE_ADDR <= MEMORY LIMIT <= 0xFFFFFFF), it is treated
as an IO access by mistake, then sent to perpheral.
This patch fixes the problem by exchanging the assignments of `MEMORYs' and
`CFGs/IOs', which assigning MEMORYs to iatu0, CFGs and IOs to iatu1.
We can still have issues with IO transfer, however memory transfer is used
predominantly therefore we are just minimizing the risk of failure.
Actually, we can not do much when we have only two viewports. We can
either not allow the less frequent IO transfers at all, or can live with a
remote possibility of getting it corrupted.
Signed-off-by: Dong Bo <dongbo4@huawei.com>
[pratyush.anand@gmail.com: Modified commit log to capture remote risk]
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_EXYNOS
drivers/pci/host/Kconfig: bool "Samsung Exynos PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Kukjin Kim <kgene@kernel.org>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_DW
drivers/pci/host/Kconfig: bool
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_SPEAR13XX
drivers/pci/host/Kconfig: bool "STMicroelectronics SPEAr PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
module_init() translates to device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_IMX6
drivers/pci/host/Kconfig: bool "Freescale i.MX6 PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
module_init() translates to device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Zhu <Richard.Zhu@freescale.com>
CC: Lucas Stach <l.stach@pengutronix.de>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_ALTERA
drivers/pci/host/Kconfig: bool "Altera PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
module_init() translates to device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ley Foon Tan <lftan@altera.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_ALTERA_MSI
drivers/pci/host/Kconfig: bool "Altera PCIe MSI feature"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ley Foon Tan <lftan@altera.com>
Bjorn Helgaas