This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP4 there is no need to have SRAM_BOOTLOADER_SZ provision
Hence put this macro under CONFIG_ARCH_OMAP2PLUS check
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP24xx/34xx/44xx: omap_type() returns the correct type:
OMAP2_DEVICE_TYPE_TEST
OMAP2_DEVICE_TYPE_EMU
OMAP2_DEVICE_TYPE_SEC
OMAP2_DEVICE_TYPE_GP
OMAP2_DEVICE_TYPE_BAD
In current implementation there are two problems:
Problem 1:
For 34xx, the current if check will never return true.
Problem 2:
For 24xx the correct type check should be with omap_type() function
Verified by checking the TRM 24xx for CONTROL_STATUS register bits
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
BugLink: https://bugs.launchpad.net/bugs/608279
Signed-off-by: Mathieu Poirier <mathieu.poirier@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev comes from u-boot and is a constant 0x20, so
Bx boards also fall in this 'if' and will get setup with the
wrong gpio_wp pin. Switch to using the Beagle revision routine
to correcly set pin 23 only for C1/2/3 and C4 Boards. Bx boards
will then use the correct default pin setting.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to the omap3530 ES3.0 Silicon being used on both the
B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
routines to differentiate the Beagle Boards.
However gpio pins 171,172,173 where setup for this prupose, so
lets use them.
Changes:
for older U-Boot's, use omap_mux_init_gpio()
keep Beagle Rev in board-omap3beagle.c
gpio_free on gpio request failure
Tested on Beagle Revisions: B5, C2, C4, and xMA
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board file changes for the digital compass hmc5843.
The interface to the device is i2c.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a GPIO bank has more than one GPIO with debounce enabled, the
debounce clock will not be fully disabled before going to
idle/suspend.
In the idle path, we just do a single clk_disable() of the bank's
debounce clock. If there are multiple debounce-enabled GPIOs in the
bank, that clocks usage count will be > 1, so the clk_disable() will
not actually disable the clock.
So the fix is to clk_disable() for every debounce-enabled GPIO in the
bank (and an equivalent clk_enable() of course.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP4 L3 interconnect is split in 3 part for power saving reason.
Because of that there is no l3_main like on OMAP2 & 3 but 3 differentes
l3_main_X instances.
In the case of OMAP4, query only the l3_main_1 part. The clock and
voltage are shared across the 3 instances.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In order to help differentiate omap_devices from normal
platform_devices, make them all a parent of a new common parent
device.
Then, in order to determine if a platform_device is also an
omap_device, checking the parent is all that is needed.
Users of this feature are the runtime PM core for OMAP, where we need
to know if a device being passed in is an omap_device or not in order
to know whether to call the omap_device API with it.
In addition, all omap_devices will now show up under /sys/devices/omap
instead of /sys/devices/platform
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 0007122ad8.
The dereference method of checking for a valid omap_device when
wrapping a platform_device is rather unsafe and dangerous.
Instead, a better way of checking for a valid omap-device is
to use a common parent device for all omap_devices, then a check
can simply be made using the device parent. The only user of this
API was the initial version of the runtime PM core for OMAP. This
has now been switched to check device parent, so there are no more
users of this API.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 8e2efde9 added milliseconds suspend wakeup time support but
same interface is not exported through debugfs
This patch enables the debugfs hook for wakeup_timer_milliseconds
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has an iva device and a dsp devcice where as OMAP2/3
has only an iva device. In this file the iva device in the
system is registered under the name dsp_dev and the API
to retrieve the iva device is omap2_get_dsp_device.
This patch renames the dsp_dev to iva_dev, renames
omap2_get_dsp_device to omap2_get_iva_device,
registers dsp_dev for OMAP4 and adds a new API
omap4_get_dsp_device to retrieve the dep_dev.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In an effort to simplify the core idle path, move any device-specific
special case handling from the core PM idle path into the CPUidle
pre-idle checking path.
This keeps the core, interrupts-disabled idle path streamlined and
independent of any device-specific handling, and also allows CPUidle
to do the checking only for certain C-states as needed. This patch
has the device checks in place for all states with the CHECK_BM flag,
namely all states >= C2.
This patch was inspired by a similar patch written by Tero Kristo as
part of a larger series to add INACTIVE state support.
NOTE: This is a baby-step towards decoupling device idle (or system
idle) from CPU idle. Eventually, CPUidle should only manage the CPU,
and device/system idle should be managed elsewhere.
Cc: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This change adds in MMC and I2C support to the HTC Herald board, as well
as adding the HTCPLD driver for the PLD used on this phone. It also
adds in the gpio-keys entries for the front directional keys and
selector and the cursor keys on the slide-out keyboard, and gpio-leds
support for the LEDs attached to the htcpld.
Additionally, SPI bus support (using the spi100k driver) and
touchscreen support (using the ads7846 driver) were added.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch:
- adds more documentation to the hwmod code
- fixes some documentation typos elsewhere in the file
- changes the _sysc_*() function names to appear in (verb, noun) order,
to match the rest of the function names.
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
For every optional clock present per hwmod per omap-device, this function
adds an entry in the clocks list of the form <dev-id=dev_name, con-id=role>,
if an entry is already present in the list of the form <dev-id=NULL, con-id=role>.
The function is called from within the framework inside omap_device_build_ss(),
after omap_device_register.
This allows drivers to get a pointer to its optional clocks based on its role
by calling clk_get(<dev*>, <role>).
Link to discussions related to this patch:
http://www.spinics.net/lists/linux-omap/msg34809.html
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified loop iterator; removed the superfluous clk_get(),
using the clk_get() in clk_add_alias() instead]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
If a module's OCP slave port is programmed to be in smartidle,
its also necessary that they have module level wakeup enabled.
Update _sysc_enable in hwmod framework to do this.
The thread "[PATCH 7/8] : Hwmod api changes" archived here:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg34212.html
has additional technical information on the rationale of this patch.
Sergei Shtylyov <sshtylyov@mvista.com> identified an indentation
problem with this patch - thanks, Sergei.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: revised patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Some modules (like GPIO, DSS...) require optionals clock to be enabled
in order to complete the sofreset properly.
Add a HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to force all optional clocks
to be enabled before reset. Disabled them once the reset is done.
TODO:
For the moment it is very hard to understand from the HW spec, which
optional clock is needed and which one is not. So the current approach
will enable all the optional clocks.
Paul proposed a much finer approach that will allow to tag only the needed
clock in the optional clock table. This might be doable as soon as we have
a clear understanding of these dependencies.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
In OMAP3 a specific SYSSTATUS register was used to get the softreset status.
Starting in OMAP4, some IPs does not have SYSSTATUS register and instead
use the SYSC softreset bit to provide the status.
Other cases might exist:
- Some IPs like McBSP does have a softreset control but no reset status.
- Some IPs that represent subsystem, like the DSS, can contains
a reset status without softreset control. The status is the aggregation
of all the sub modules reset status.
- Add a new flag (SYSC_HAS_RESET_STATUS) to identify the new programming model
and replace the previous SYSS_MISSING, that was used to flag IP with
softreset control but without the SYSSTATUS register, with a specific
SYSS_HAS_RESET_STATUS flag.
- MCSPI and MMC contains both programming models, so the legacy one
will be prevented by removing the syss offset field that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Expose an hardreset API from hwmod in order to assert / deassert all the
individual reset lines that belong to an hwmod. This API is needed by
some of the more complicated processor drivers, e.g., DSP/Bridge,
Syslink, etc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Force the softreset of every IPs during the _setup phase.
IPs that cannot support softreset or that should not
be reset must set the HWMOD_INIT_NO_RESET flag in the
hwmod struct.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most processor IPs does have a hardreset signal controlled by the PRM.
This is different of the softreset used for local IP reset from the
SYSCONFIG register.
The granularity can be much finer than orginal HWMOD, for ex, the IVA
hwmod contains 3 reset lines, the IPU 3 as well, the DSP 2...
Since this granularity is needed by the driver, we have to ensure
than one hwmod exist for each hardreset line.
- Store reset lines as hwmod resources that a driver can query by name like
an irq or sdma line.
- Add two functions for asserting / deasserting reset lines in hwmods
processor that require manual reset control.
- Add one functions to get the current reset state.
- If an hwmod contains only one line, an automatic assertion / de-assertion
is done.
-> de-assert the hardreset line only during enable from disable transition
-> assert the hardreset line only during shutdown
Note: The hwmods with hardreset line and HWMOD_INIT_NO_RESET flag must be
kept in INITIALIZED state.
They can be properly enabled only if the hardreset line is de-asserted
before.
For information here is the list of IPs with HW reset control
on an OMAP4430 device:
RM_DSP_RSTCTRL
1,1,'RST2','RW','1','DSP - MMU, cache and slave interface reset control'
0,0,'RST1','RW','1','DSP - DSP reset control'
RM_IVA_RSTCTRL
2,2,'RST3','RW','1','IVA logic and SL2 reset control'
1,1,'RST2','RW','1','IVA Sequencer2 reset control'
0,0,'RST1','RW','1','IVA sequencer1 reset control'
RM_IPU_RSTCTRL
2,2,'RST3','RW','1','IPU MMU and CACHE interface reset control.'
1,1,'RST2','RW','1','IPU Cortex M3 CPU2 reset control.'
0,0,'RST1','RW','1','IPU Cortex M3 CPU1 reset control.'
PRM_RSTCTRL
1,1,'RST_GLOBAL_COLD_SW','RW','0','Global COLD software reset control.'
0,0,'RST_GLOBAL_WARM_SW','RW','0','Global WARM software reset control.'
RM_CPU0_CPU0_RSTCTRL
RM_CPU1_CPU1_RSTCTRL
0,0,'RST','RW','0','Cortex A9 CPU0&1 warm local reset control'
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made the hardreset functions static; moved the register
twiddling into prm*.c functions in previous patches; changed the
function names to conform with hwmod practice]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch adds hard-reset support for processor modules (e.g., DSP, IVA)
on OMAP2/3 platforms. It's based on the OMAP4 hard-reset support that Benoît
developed in the previous patch.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM. This patch adds an API for this purpose
for OMAP4 devices:
int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Since OMAP4 is using an absolute address, the current PRM accessors
are not useable.
OMAP4 adaptation for these API are currently ongoing, so define temp
version until the proper ones are defined.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap_hwmod_mutex is being used to protect both the list
access/modification and concurrent access to hwmod functions. This
patch separates these two types of locking.
First, omap_hwmod_mutex is used only to protect access and
modification of omap_hwmod_list. Also cleaned up some comments
referring to this mutex that are no longer needed.
Then, for protecting concurrent access to hwmod functions, use a
per-hwmod mutex. This protects concurrent access to a single hwmod,
but would allow concurrent access to different hwmods.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added structure documentation; changed mutex variable
name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 platform has different register bits for Warm and Cold Resets.
Write one into appropriate bits.
Signed-off-by: Rajeev Kulkarni <rajeevk@ti.com>
Cc: Leed Aguilar <leed.aguilar@ti.com>
[b-cousson@ti.com: Change the define with the proper one from omap4 headers]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The reset function wrongly used the state flag as a bit mask and was trying
to re-enable after a reset.
hwmod is still enabled for the PRCM point of view after a softreset
so there is no need to re-enable.
Remove the state check from omap_hwmod_reset since the _reset
function is checking that as well and in addition can generate
a warning
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
[b-cousson@ti.com: remove the wrong test, remove the re-enable]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The disable function was disabling clocks and dependencies
from both enable and idle state. Since idle function is already
disabling both, an enable -> idle -> disable sequence will
try to disable twice the clocks and thus generate a
"Trying disable clock XXX with 0 usecount" warning.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
On OMAP1, we do not have omap_device + omap_hwmod to manage the
device-specific idle, enable and shutdown. Instead, just
enable/disable device clocks automatically at the runtime PM level.
This allows drivers to not have any OMAP1 specific clock management
and allows them to simply use the runtime PM API to manage clocks.
OMAP1 compile fixes Manjunatha GK <manjugk@ti.com>
Cc: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement the new runtime PM framework as a thin layer on top of the
omap_device API. OMAP specific runtime PM methods are registered with
the as custom methods on the platform_bus.
In order to determine if a device is an omap_device, its parent device
is checked. All omap_devices have a new 'omap_device_parent_ device
as their parent device, so checking for this parent is used to check
for valid omap_devices. If a device is an omap_device, then the
appropriate omap_device functions are called for it. If not, only the
generic runtime PM functions are called.
Device driver's ->runtime_idle() hook is called when the runtime PM
usecount reaches zero for that device. Driver's ->runtime_suspend()
hooks are called just before the device is disabled (via
omap_device_idle()), and device driver ->runtime_resume() hooks are
called just after device has been enabled (via omap_device_enable().)
OMAP4 build support from Rajendra Nayak <rnayak@ti.com>.
OMAP2 build support from Charulatha V <charu@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Charulatha V <charu@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes omap3 hardcodings from pm-debug.c
so that enabling PM debugfs support does break compilation
for other OMAP's. This is a preparatory patch for supporting
OMAP4 pm entries through PM debugfs.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup indentation around IO wakeup enable, the '\' terminator is
not required in C when wrapping an expression past end-of-line.
Whitespace change only.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dma request line attribute was named dma channel, which leads
to confusion with the real dma channel definition.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch addresses below things
- Renaming existing omap3_defconfig which has OMAP2, OMAP3 and OMAP4 builds
enabled to more appropriate name 'omap2plus_defconfig'
- L1 cache shift is suppose to be 5 on OMAP4 where as it is 6 on previous
OMAPs. Keeping it to 5 is safer option for OMAP4 and previous OMAPs. For
OMAP3 only build the shift would be still 6
- Enable needed Errata's for OMAP4 to work with DMA based device drivers
CONFIG_PL310_ERRATA_588369=y
CONFIG_ARM_ERRATA_720789=y
- Enable the Micrel ethernet controller
CONFIG_KS8851=y
CONFIG_KS8851_MLL=y
With above three changes, OMAP4 ethernet, mmc etc works reliably.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the recent changes to core ARM kernel code, we can now
boot SMP kernel on UP systems. Update omap3_defconfig to
enable SMP. This allows us to remove omap_4430sdp_defconfig.
In addition to enabling SMP, we also need to disable some
options to make the system boot:
- For some reason LOCK_STAT causes tons of
WARNING: at mm/percpu-vm.c:320 pcpu_alloc+0x2fc/0x888()
so disable it for now.
- MUSB init fails for multi-omap, disable it for now.
- LOCAL_TIMERS hangs on omap4, disable it for now.
Also disable DEBUG_LL as this should be only enabled for
debugging.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to make sure that only the first do_signal() to be handled on
the way out syscall will bother with syscall restarts; additionally, the
check on the "signal has user handler" path had been wrong - compare
with restart prevention in sigreturn()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_signal() should place the syscall number in gr7, not gr8 when
handling ERESTART_WOULDBLOCK.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use force_sigsegv() rather than force_sig(SIGSEGV, ...) as the former
resets the SEGV handler pointer which will kill the process, rather than
leaving it open to an infinite loop if the SEGV handler itself caused a
SEGV signal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) sa_handler might be maliciously set to point to kernel memory;
blindly dereferencing it in FDPIC case is a Bad Idea(tm).
b) I'm not sure you need that set_fs(USER_DS) there at all, but if you
do, you'd better do it *before* checking the frame you've decided to
use with access_ok(), lest sigaltstack() becomes a convenient
roothole.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset restart_block.fn on executing a sigreturn such that any currently
pending system call restarts will be forced to return -EINTR.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: deal with multiple simultaneously pending signals
alpha: fix a 14 years old bug in sigreturn tracing
alpha: unb0rk sigsuspend() and rt_sigsuspend()
alpha: belated ERESTART_RESTARTBLOCK race fix
alpha: Shift perf event pending work earlier in timer interrupt
alpha: wire up fanotify and prlimit64 syscalls
alpha: kill big kernel lock
alpha: fix build breakage in asm/cacheflush.h
alpha: remove unnecessary cast from void* in assignment.
alpha: Use static const char * const where possible
Unlike the other targets, alpha sets _one_ sigframe and
buggers off until the next syscall/interrupt, even if
more signals are pending. It leads to quite a few unpleasant
inconsistencies, starting with SIGSEGV potentially arriving
not where it should and including e.g. mess with sigsuspend();
consider two pending signals blocked until sigsuspend()
unblocks them. We pick the first one; then, if we are hit
by interrupt while in the handler, we process the second one
as well. If we are not, and if no syscalls had been made,
we get out of the first handler and leave the second signal
pending; normally sigreturn() would've picked it anyway, but
here it starts with restoring the original mask and voila -
the second signal is blocked again. On everything else we
get both delivered consistently.
It's actually easy to fix; the only thing to watch out for
is prevention of double syscall restart. Fortunately, the
idea I've nicked from arm fix by rmk works just fine...
Testcase demonstrating the behaviour in question; on alpha
we get one or both flags set (usually one), on everything
else both are always set.
#include <signal.h>
#include <stdio.h>
int had1, had2;
void f1(int sig) { had1 = 1; }
void f2(int sig) { had2 = 1; }
main()
{
sigset_t set1, set2;
sigemptyset(&set1);
sigemptyset(&set2);
sigaddset(&set2, 1);
sigaddset(&set2, 2);
signal(1, f1);
signal(2, f2);
sigprocmask(SIG_SETMASK, &set2, NULL);
raise(1);
raise(2);
sigsuspend(&set1);
printf("had1:%d had2:%d\n", had1, had2);
}
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
The way sigreturn() is implemented on alpha breaks PTRACE_SYSCALL,
all way back to 1.3.95 when alpha has grown PTRACE_SYSCALL support.
What happens is direct return to ret_from_syscall, in order to bypass
mangling of a3 (error indicator) and prevent other mutilations of
registers (e.g. by syscall restart). That's fine, but... the entire
TIF_SYSCALL_TRACE codepath is kept separate on alpha and post-syscall
stopping/notifying the tracer is after the syscall. And the normal
path we are forcibly switching to doesn't have it.
So we end up with *one* stop in traced sigreturn() vs. two in other
syscalls. And yes, strace is visibly broken by that; try to strace
the following
#include <signal.h>
#include <stdio.h>
void f(int sig) {}
main()
{
signal(SIGHUP, f);
raise(SIGHUP);
write(1, "eeeek\n", 6);
}
and watch the show. The
close(1) = 405
in the end of strace output is coming from return value of write() (6 ==
__NR_close on alpha) and syscall number of exit_group() (__NR_exit_group ==
405 there).
The fix is fairly simple - the only thing we end up missing is the call
of syscall_trace() and we can tell whether we'd been called from the
SYSCALL_TRACE path by checking ra value. Since we are setting the
switch_stack up (that's what sys_sigreturn() does), we have the right
environment for calling syscall_trace() - just before we call
undo_switch_stack() and return. Since undo_switch_stack() will overwrite
s0 anyway, we can use it to store the result of "has it been called from
SYSCALL_TRACE path?" check. The same thing applies in rt_sigreturn().
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Old code used to set regs->r0 and regs->r19 to force the right
return value. Leaving that after switch to ERESTARTNOHAND
was a Bad Idea(tm), since now that screws the restart - if we
hit the case when get_signal_to_deliver() returns 0, we will
step back to syscall insn, with v0 set to EINTR and a3 to 1.
The latter won't matter, since EINTR is 4, aka __NR_write.
Testcase:
#include <signal.h>
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
main()
{
sigset_t mask;
sigemptyset(&mask);
sigaddset(&mask, SIGCONT);
sigprocmask(SIG_SETMASK, &mask, NULL);
kill(0, SIGCONT);
syscall(__NR_sigsuspend, 1, "b0rken\n", 7);
}
results on alpha in immediate message to stdout...
Fix is obvious; moreover, since we don't need regs anymore, we can
switch to normal prototypes for these guys and lose the wrappers.
Even better, rt_sigsuspend() is identical to generic version in
kernel/signal.c now.
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
same thing as had been done on other targets back in 2003 -
move setting ->restart_block.fn into {rt_,}sigreturn().
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Pending work from the performance event subsystem is executed in
the timer interrupt. This patch shifts the call to
perf_event_do_pending() before the call to update_process_times()
as the latter may call back into the perf event subsystem and it
is prudent to have the pending work executed first.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
The 2.6.36-rc kernel added three new system calls:
fanotify_init, fanotify_mark, and prlimit64. This
patch wires them up on Alpha.
Built and booted on an XP900. Untested beyond that.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Matt Turner <mattst88@gmail.com>
All uses of the BKL on alpha are totally bogus, nothing
is really protected by this. Remove the remaining users
so we don't have to mark alpha as 'depends on BKL'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
Alpha SMP flush_icache_user_range() is implemented as an inline
function inside include/asm/cacheflush.h. It dereferences @current
but doesn't include linux/sched.h and thus causes build failure if
linux/sched.h wasn't included previously. Fix it by including the
needed header file explicitly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Add IORESOURCE_IRQ_HIGHLEVEL irq flag to dm9000 driver
platform data in board mach-real6410.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix errors reported by checkpatch.pl script
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Avoids build warnings due to the undeclared non-statics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If a signal hits us outside of a syscall and another gets delivered
when we are in sigreturn (e.g. because it had been in sa_mask for
the first one and got sent to us while we'd been in the first handler),
we have a chance of returning from the second handler to location one
insn prior to where we ought to return. If r0 happens to contain -513
(-ERESTARTNOINTR), sigreturn will get confused into doing restart
syscall song and dance.
Incredible joy to debug, since it manifests as random, infrequent and
very hard to reproduce double execution of instructions in userland
code...
The fix is simple - mark it "don't bother with restarts" in wrapper,
i.e. set r8 to 0 in sys_sigreturn and sys_rt_sigreturn wrappers,
suppressing the syscall restart handling on return from these guys.
They can't legitimately return a restart-worthy error anyway.
Testcase:
#include <unistd.h>
#include <signal.h>
#include <stdlib.h>
#include <sys/time.h>
#include <errno.h>
void f(int n)
{
__asm__ __volatile__(
"ldr r0, [%0]\n"
"b 1f\n"
"b 2f\n"
"1:b .\n"
"2:\n" : : "r"(&n));
}
void handler1(int sig) { }
void handler2(int sig) { raise(1); }
void handler3(int sig) { exit(0); }
main()
{
struct sigaction s = {.sa_handler = handler2};
struct itimerval t1 = { .it_value = {1} };
struct itimerval t2 = { .it_value = {2} };
signal(1, handler1);
sigemptyset(&s.sa_mask);
sigaddset(&s.sa_mask, 1);
sigaction(SIGALRM, &s, NULL);
signal(SIGVTALRM, handler3);
setitimer(ITIMER_REAL, &t1, NULL);
setitimer(ITIMER_VIRTUAL, &t2, NULL);
f(-513); /* -ERESTARTNOINTR */
write(1, "buggered\n", 9);
return 1;
}
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Work around hardware stupidity
x86, build: Disable -fPIE when compiling with CONFIG_CC_STACKPROTECTOR=y
x86, cpufeature: Suppress compiler warning with gcc 3.x
x86, UV: Fix initialization of max_pnode
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: fix formatting bug in register dumps
arch/tile: fix memcpy_fromio()/memcpy_toio() signatures
arch/tile: Save and restore extra user state for tilegx
arch/tile: Change struct sigcontext to be more useful
arch/tile: finish const-ifying sys_execve()
Tony's fix (f574c84319) has a small bug,
it incorrectly uses "r3" as a scratch register in the first of the two
unlock paths ... it is also inefficient. Optimize the fast path again.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This cut-and-paste bug was caused by rewriting the register dump
code to use only a single printk per line of output.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
During context switch, save and restore a couple of additional bits of
tilegx user state that can be persistently modified by userspace.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Rather than just using pt_regs, it now contains the actual saved
state explicitly, similar to pt_regs. By doing it this way, we
provide a cleaner API for userspace (or equivalently, we avoid the
need for libc to provide its own definition of sigcontext).
While we're at it, move PT_FLAGS_xxx to where they are not visible
from userspace. And always pass siginfo and mcontext to signal
handlers, even if they claim they don't need it, since sometimes
they actually try to use it anyway in practice.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The sys_execve() implementation was properly const-ified but not
the declaration, the syscall wrappers, or the compat version.
This change completes the constification process.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* ssh://master.kernel.org/home/hpa/tree/sec:
x86-64, compat: Retruncate rax after ia32 syscall entry tracing
x86-64, compat: Test %rax for the syscall number, not %eax
compat: Make compat_alloc_user_space() incorporate the access_ok()
Fix up the IRQ names for the MN10300 on-chip serial ports in the driver as
request_interrupt() no longer allows names containing slashes, giving a warning
like the following if one is encountered:
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:323 __xlate_proc_name+0x62/0x7c()
name 'ttySM0/Rx'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit d4d6715, we reopened an old hole for a 64-bit ptracer touching a
32-bit tracee in system call entry. A %rax value set via ptrace at the
entry tracing stop gets used whole as a 32-bit syscall number, while we
only check the low 32 bits for validity.
Fix it by truncating %rax back to 32 bits after syscall_trace_enter,
in addition to testing the full 64 bits as has already been added.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On 64 bits, we always, by necessity, jump through the system call
table via %rax. For 32-bit system calls, in theory the system call
number is stored in %eax, and the code was testing %eax for a valid
system call number. At one point we loaded the stored value back from
the stack to enforce zero-extension, but that was removed in checkin
d4d6715016. An actual 32-bit process
will not be able to introduce a non-zero-extended number, but it can
happen via ptrace.
Instead of re-introducing the zero-extension, test what we are
actually going to use, i.e. %rax. This only adds a handful of REX
prefixes to the code.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area. A missing call could
introduce problems on some architectures.
This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.
This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures. This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>
This more or less reverts commits 08be979 (x86: Force HPET
readback_cmp for all ATI chipsets) and 30a564be (x86, hpet: Restrict
read back to affected ATI chipsets) to the status of commit 8da854c
(x86, hpet: Erratum workaround for read after write of HPET
comparator).
The delta to commit 8da854c is mostly comments and the change from
WARN_ONCE to printk_once as we know the call path of this function
already.
This needs really in depth explanation:
First of all the HPET design is a complete failure. Having a counter
compare register which generates an interrupt on matching values
forces the software to do at least one superfluous readback of the
counter register.
While it is nice in theory to program "absolute" time events it is
practically useless because the timer runs at some absurd frequency
which can never be matched to real world units. So we are forced to
calculate a relative delta and this forces a readout of the actual
counter value, adding the delta and programming the compare
register. When the delta is small enough we run into the danger that
we program a compare value which is already in the past. Due to the
compare for equal nature of HPET we need to read back the counter
value after writing the compare rehgister (btw. this is necessary for
absolute timeouts as well) to make sure that we did not miss the timer
event. We try to work around that by setting the minimum delta to a
value which is larger than the theoretical time which elapses between
the counter readout and the compare register write, but that's only
true in theory. A NMI or SMI which hits between the readout and the
write can easily push us beyond that limit. This would result in
waiting for the next HPET timer interrupt until the 32bit wraparound
of the counter happens which takes about 306 seconds.
So we designed the next event function to look like:
match = read_cnt() + delta;
write_compare_ref(match);
return read_cnt() < match ? 0 : -ETIME;
At some point we got into trouble with certain ATI chipsets. Even the
above "safe" procedure failed. The reason was that the write to the
compare register was delayed probably for performance reasons. The
theory was that they wanted to avoid the synchronization of the write
with the HPET clock, which is understandable. So the write does not
hit the compare register directly instead it goes to some intermediate
register which is copied to the real compare register in sync with the
HPET clock. That opens another window for hitting the dreaded "wait
for a wraparound" problem.
To work around that "optimization" we added a read back of the compare
register which either enforced the update of the just written value or
just delayed the readout of the counter enough to avoid the issue. We
unfortunately never got any affirmative info from ATI/AMD about this.
One thing is sure, that we nuked the performance "optimization" that
way completely and I'm pretty sure that the result is worse than
before some HW folks came up with those.
Just for paranoia reasons I added a check whether the read back
compare register value was the same as the value we wrote right
before. That paranoia check triggered a couple of years after it was
added on an Intel ICH9 chipset. Venki added a workaround (commit
8da854c) which was reading the compare register twice when the first
check failed. We considered this to be a penalty in general and
restricted the readback (thus the wasted CPU cycles) to the known to
be affected ATI chipsets.
This turned out to be a utterly wrong decision. 2.6.35 testers
experienced massive problems and finally one of them bisected it down
to commit 30a564be which spured some further investigation.
Finally we got confirmation that the write to the compare register can
be delayed by up to two HPET clock cycles which explains the problems
nicely. All we can do about this is to go back to Venki's initial
workaround in a slightly modified version.
Just for the record I need to say, that all of this could have been
avoided if hardware designers and of course the HPET committee would
have thought about the consequences for a split second. It's out of my
comprehension why designing a working timer is so hard. There are two
ways to achieve it:
1) Use a counter wrap around aware compare_reg <= counter_reg
implementation instead of the easy compare_reg == counter_reg
Downsides:
- It needs more silicon.
- It needs a readout of the counter to apply a relative
timeout. This is necessary as the counter does not run in
any useful (and adjustable) frequency and there is no
guarantee that the counter which is used for timer events is
the same which is used for reading the actual time (and
therefor for calculating the delta)
Upsides:
- None
2) Use a simple down counter for relative timer events
Downsides:
- Absolute timeouts are not possible, which is not a problem
at all in the context of an OS and the expected
max. latencies/jitter (also see Downsides of #1)
Upsides:
- It needs less or equal silicon.
- It works ALWAYS
- It is way faster than a compare register based solution (One
write versus one write plus at least one and up to four
reads)
I would not be so grumpy about all of this, if I would not have been
ignored for many years when pointing out these flaws to various
hardware folks. I really hate timers (at least those which seem to be
designed by janitors).
Though finally we got a reasonable explanation plus a solution and I
want to thank all the folks involved in chasing it down and providing
valuable input to this.
Bisected-by: Nix <nix@esperi.org.uk>
Reported-by: Artur Skawina <art.08.09@gmail.com>
Reported-by: Damien Wyart <damien.wyart@free.fr>
Reported-by: John Drescher <drescherjm@gmail.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irqs.h usage here got missed in the Samsung platform reorganisation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes bug on gpio drive strength helper function.
The offset should be like follwoing.
- off = chip->chip.base - pin;
+ off = pin - chip->chip.base;
In the s5p_gpio_get_drvstr(),
the second line is unnecessary, because overwrite drvstr.
drvstr = __raw_readl(reg);
- drvstr = 0xffff & (0x3 << shift);
And need 2bit masking before return the drvstr value.
drvstr = drvstr >> shift;
+ drvstr &= 0x3;
In the s5p_gpio_set_drvstr(), need relevant bit clear.
tmp = __raw_readl(reg);
+ tmp &= ~(0x3 << shift);
tmp |= drvstr << shift;
Reported-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes on defined drive strength value for GPIO.
According to data sheet, if we want drive strength 1x, the value
should be 00(b), if 2x should be 10(b), if 3x should be 01(b),
and if 4x should be 11(b). Also fixes comment(from S5C to S5P).
Reported-by: Janghyuck Kim <janghyuck.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These clocks enables FIMC driver to operate on machines, which
bootloader power gated FIMC devices to save power on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
CLK_GATE_IP3[8] is RESERVED. The port "I2C_HDMI_DDC" of CLK_GATE_IP3[10] is
used as another I2C port. Therefore, defined the unused I2C-1 as another I2C
there was left undefined but used.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
IO registers region size of all FIMC versions is less than 1kB so there
is no need to reserve 1M.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
FIMC driver uses DMA_coherent allocator, which requires proper dma mask
to be set.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The arch/x86/Makefile uses scripts/gcc-x86_$(BITS)-has-stack-protector.sh
to check if cc1 supports -fstack-protector. When -fPIE is passed to cc1,
these scripts fail causing stack protection to be disabled even when it
is available.
This fix is similar to commit c47efe5548
Reported-by: Kai Dietrich <mail@cleeus.de>
Signed-off-by: Magnus Granberg <zorry@gentoo.org>
LKML-Reference: <20100913101319.748A1148E216@opensource.dyc.edu>
Signed-off-by: Anthony G. Basile <basile@opensource.dyc.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Gcc 3.x generates a warning
arch/x86/include/asm/cpufeature.h: In function `__static_cpu_has':
arch/x86/include/asm/cpufeature.h:326: warning: asm operand 1 probably doesn't match constraints
on each file.
But static_cpu_has() for gcc 3.x does not need __static_cpu_has().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
LKML-Reference: <201008300127.o7U1RC6Z044051@www262.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix siglock
Quoth Tony:
"I committed the fix for this last week prior to your -rc4 announcement
reminding us to give proper "Reported-by:" credit. This one should have
had:
Reported-by: Tony Ernst <tee@sgi.com>
and also
Much-useful-investigation-and-tracing-by: Hedi Berriche <hedi@sgi.com>
Much-useful-investigation-and-tracing-by: Petr Tesarik <ptesarik@novell.com>"
Santosh Shilimkar