Move the checking of the LOG_DEVICE into a function to reduce the
number of #ifdefs and ensure more of the code gets compiled/checked,
and make it easier to change this for internal debugging purposes
(such as checking >1 device).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The handling for the first two cases in regmap_bulk_write is
essentially identical. The first case is just a better implementation of
the second, supporting 8 byte registers and doing the locking manually to
avoid bouncing the lock for each register. Drop some redundant code by
removing the second of these cases and allowing both situations to be
handled by the same code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw writes may need to be split into small chunks if max_raw_write is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_write will split a write into chunks before
calling regmap_raw_write if max_raw_write is set. It is more logical
for this handling to be inside regmap_raw_write itself, as this
removes the need to keep re-implementing the chunking code, which
would be the same for all users of regmap_raw_write.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case were the bulk transaction is split up into smaller chunks
data is passed directly to regmap_raw_write. However regmap_bulk_write
uses data in host endian and regmap_raw_write expects data in device
endian. As such if the host and device differ in endian the wrong data
will be written to the device. Correct this issue using a similar
approach to the single raw write case below it, duplicate the data
into a new buffer and use parse_inplace to format the data correctly.
Fixes: adaac45975 ("regmap: Introduce max_raw_read/write for regmap_bulk_read/write")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This registers regmaps with debugfs even when they do not have an
associated device. For example, this is common for syscon regmaps.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bulk reads may potentially read a lot of registers and regmap_read will
take and release the regmap lock for each register. Avoid bouncing
the lock so frequently by holding the lock locally and calling
_regmap_read instead. This also has the nice side-effect that all the
reads will be done atomically so no other threads can sneak a write in
during the regmap_bulk_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Raw reads may need to be split into small chunks if max_raw_read is
set. Tidy up the code implementing this, the new code is slightly
clearer, slightly shorter and slightly more efficient.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap_bulk_read will split a read into chunks before
calling regmap_raw_read if max_raw_read is set. It is more logical for
this handling to be inside regmap_raw_read itself, as this removes the
need to keep re-implementing the chunking code, which would be the
same for all users of regmap_raw_read.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a helper function exists for calculating register offsets lets use
that rather than open coding with the reg_stride.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bulk read can be implemented either through regmap_raw_read, or
by reading each register individually using regmap_read. Both
regmap_read and regmap_bulk_read should return values in native
endian. In the individual case the current implementation calls
format_val to put the data into the output array, which can cause
endian issues. The regmap_read will have already converted the data
into native endian, if the hosts endian differs from the device then
format_val will switch the endian back again.
Rather than using format_val simply use the code that is called if
there is no format_val function. This code supports all cases except
24-bit but there don't appear to be any users of regmap_bulk_read for
24-bit. Additionally, it would have to be a big endian host for the
old code to actually function correctly anyway.
Fixes: 15b8d2c41f ("regmap: Fix regmap_bulk_read in BE mode")
Reported-by: David Rhodes <david.rhodes@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cache pointer points to the actual memory used by the cache, as the
comparison here is looking for the type of the cache it should check
against cache_type.
Fixes: 1ea975cf1e ("regmap: Add a function to check if a regmap register is cached")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation is broken for regmaps that have a reg_stride,
since it doesn't take the stride into account. Correct this by using the
helper function to calculate the register offset.
Fixes: f01ee60fff ("regmap: implement register striding")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9 ("regmap: Add raw_write/read checks for max_raw_write/read sizes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The map->work_buf is a buffer preallocated in __regmap_init() with size
allowing it to store all 3 parts of a buffer - reg, pad and val. While
reg and val parts are always properly setup before each transaction, the
pad part is left at its default value (zeros). Until it is overwritten,
that is.
_regmap_bus_read(), when calling _regmap_raw_read() uses beginning of
work_buf as a place to store data read. Usually that is fine but if
val_bits > reg_bits && pad_bits > 0, padding area of work_buf() may get
overwritten. Since padding is not zeroed before each transaction,
garbage will be used on next calls.
This patch moves the val pointer used for _regmap_raw_read() to point
to a part of work_buf intended for storing value read.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we just copy over the pointer passed to regmap_init() in
the regmap config struct. To be on the safe side: duplicate the string
with kstrdup_const() so that if an unaware user passes an address to
a stack-allocated buffer, we won't crash.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recently added support for disabling the regmap internal locking left
debugfs enabled for devices with the locking disabled. This is a problem
since debugfs allows userspace to do things like initiate reads from the
hardware which will use the scratch buffers protected by the regmap locking
so could cause data corruption.
For safety address this by just disabling debugfs for these devices. That
is overly conservative since some of the debugfs files just read internal
data structures but it's much simpler to implmement and less likely to
lead to problems with tooling that works with debugfs.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor naming convention tweak.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a use case in the at24 EEPROM driver (recently converted to
using regmap instead of raw i2c/smbus calls) where we read from/write
to the regmap in a loop, while protecting the entire loop with
a mutex.
Currently this implicitly makes us use two mutexes - one in the driver
and one in regmap. While browsing the code for similar use cases I
noticed a significant number of places where locking *seems* redundant.
Allow users to completely disable any locking mechanisms in regmap
config.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hwspinlock was changed to a bool by commit d048236dfd
("hwspinlock: Change hwspinlock to a bool"), so we do not need
the REGMAP_HWSPINLOCK config to select hwspinlock or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the warning of label 'err_map' defined but not used.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous patch to allow the hwspinlock code to be disabled missed
handling the free in the error path, do so using the better IS_ENABLED()
pattern as suggested by Baolin. While we're at it also check that we have
a hardware spinlock before freeing it - the core code reports an error
when freeing an invalid lock.
Suggested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike other lock types hwspinlocks are optional and can be built
modular so we can't use them unconditionally in regmap so add a config
option that drivers that want to use hwspinlocks with regmap can select
which will ensure that hwspinlock is built in.
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms, when reading or writing some special registers through
regmap, we should acquire one hardware spinlock to synchronize between
the multiple subsystems. Thus this patch adds the hardware spinlock
support for regmap.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the kernel-doc comments in regmap don't actually generate
correctly. This patch fixes up a few common issues, corrects some typos
and adds some missing argument descriptions.
The most common issues being using a : after the function name which
causes the short description to not render correctly and not separating
the long and short descriptions of the function. There are quite a few
instances of arguments not being described or given the wrong name as
well.
This patch doesn't fixup functions/structures that are currently missing
descriptions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 815806e39b ("regmap: drop cache if the bus transfer error")
added a call to regcache_drop_region() to error path in
_regmap_raw_write(). However that path runs with regmap lock taken,
and regcache_drop_region() tries to re-take it, causing a deadlock.
Fix that by calling map->cache_ops->drop() directly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This with the longer read and write masks allow supporting more
exotic devices. For example a little endian SPI device:
static const struct regmap_config foo_regmap_config = {
.reg_bits = 16,
.reg_stride = 4,
.val_bits = 16,
.write_flag_mask = 0x8000,
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
.val_format_endian = REGMAP_ENDIAN_LITTLE,
...
};
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently only support masking the top bit for read and write
flags. Let's make the mask unsigned long and mask the bytes based
on the configured register length to make things more generic.
This allows using regmap for more exotic combinations like SPI
devices that need little endian addressing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_write
->_regmap_raw_write
-->regcache_write first and than use map->bus->write to wirte i2c or spi
But if the i2c or spi transfer failed, But the cache is updated, So if I use
regmap_read will get the cache data which is not the real register value.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to check if a regmap register is cached. This will be used
in debugfs to dump the cached values of write only registers.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When doing a bulk writes from a device which lacks raw I/O support we
fall back to doing register at a time reads but we still use the raw
formatters in order to render the data into the word size used by the
device (since bulk reads still operate on the device word size rather
than unsigned ints). This means that devices without raw formatting
such as those that provide reg_read() are not supported. Provide
handling for them by copying the values read into native endian values
of the appropriate size.
This complements commit d5b98eb124 ("regmap: Support bulk reads for
devices without raw formatting").
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown