Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports. In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60. Port 6 is the host port.
Setting a zero value can be used to stop port from receiving.
However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate. This does not apply to
multicast and broadcast addresses though. To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.
Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving the conflict wrt. the vxlan_fdb_update call
in vxlan_changelink() I made the last argument false instead
of true.
Fix this.
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds some misc updates and the support for tunnels over VLAN
tc offloads.
From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock
From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128
From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.
Patch 4 avoids crash for TC flow with egress upper devices
Patch 5 refactors tunnel routing devs into a helper function
Patch 6 avoids crash for TC encap flows with vlan on underlay
Patches 7-8 refactor encap tunnel header preparing code.
Patch 9 adds support for building VLAN tagged ETH header.
Patch 10 adds support for tunnel routing to VLAN device.
From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcG5O8AAoJEEg/ir3gV/o+v0AH/ja1bJ6PkAlw2bCRMIuI6HK/
1vh9n8D74tIOAlvUi6QiLOgJ7CLdAgiAVFppDWzJSBUsY2XNAtRdYvLDDt9hGafO
QGysBWNVcX2aUVp+pLDCCVEYBWyyIzW416CWHx2IUgdAg9S6cvJK6P/81wd+l4Zp
8YlPstEUANP/JKZxHHjSelMcnY+Bj0JrDzuyyyaQdwmcHo5I7Ht0tNex14yFfFbl
gd7YvfPr1PtovPX2w9hMt3y3ml4mommB+jtxc0+59D+A7680hBOpAnH5pONms9rv
OKKKV8KqpxL1m32/TGbd7XSG+llLJwsSM6RtD4oUdiPA4iCiVDVdreP5vac52C4=
=0QQ5
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-12-19
This series adds some misc updates and the support for tunnels over VLAN
tc offloads.
From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock
From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128
From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.
Patch 4 avoids crash for TC flow with egress upper devices
Patch 5 refactors tunnel routing devs into a helper function
Patch 6 avoids crash for TC encap flows with vlan on underlay
Patches 7-8 refactor encap tunnel header preparing code.
Patch 9 adds support for building VLAN tagged ETH header.
Patch 10 adds support for tunnel routing to VLAN device.
From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
VID 1 is not reserved anymore, so remove the check that prevented the
creation of VLAN devices with this VID over mlxsw ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.
The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.
Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.
The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function allows flushing all the existing VLAN entries on a port. It
is invoked when a port is destroyed and when it is unlinked from a LAG.
In the latter case, when moving to the new default VLAN, there will not
be a need to destroy the default VLAN entry.
Therefore, add an argument that allows to control whether the default
port VLAN should be destroyed or not. Currently it is always set to
'true'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver does not set the port's PVID when initializing a
new port. This is because the driver is using VID 1 as PVID which is the
firmware default.
Subsequent patches are going to change the PVID the driver is setting
when initializing a new port.
Prepare for that by explicitly setting the port's PVID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).
Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.
In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.
The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.
Instead, call into the bridge code which will check if NVE should be
enabled on the FID.
This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-12-20
This series contains updates to e100, igb, ixgbe, i40e and ice drivers.
I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics. This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.
Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.
Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.
YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.
Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.
Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.
Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.
Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in. This was due to the
driver not setting PME during runtime suspend.
Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
Use the mii_bus callbacks to address the entire clause 22/45 address
space. Enables userspace to poke switch registers instead of a single
PHY address.
The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock. This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.
While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit 42eca23021 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes: 42eca23021 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.
See commit 13a8cd191a ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Out of bound read reported by KASan.
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.
The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.
The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
on CPU0.
In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.
CC: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ath.git patches for 4.21. Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The top word of the constant can only have bits set if sign
extension set it to all-1, therefore we don't really have to
mask the top half of the register. We can just OR it into
the result as is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The verifier will now understand the JSET instruction, so don't
mark the dead branch in the JIT as noop. We won't generate any
code, anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For a little better performance on faster machines and faster link
speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older firmware only supports 16-bit flow handle, because of which the
number of flows that can be offloaded can’t scale beyond a point.
Newer firmware supports 64-bit flow handle enabling the host to scale
upto millions of flows. With the new 64-bit flow handle support, driver
has to query flow stats in a different way compared to the older approach.
This patch adds support for 64-bit flow handle and new way to query
flow stats.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RDMA is supported on the 57500 chip, increase context memory
allocations for the resources used by RDMA.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new functions bnxt_alloc_ctx_pg_tbls()/bnxt_free_ctx_pg_tbls()
to allocate and free pages for context memory. The new functions
will handle the different levels of paging support and allocate/free
the pages accordingly using the existing functions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support level 2 context page memory structures, enhance the
bnxt_ring_mem_info structure with a "depth" field to specify the page
level and add a flag to specify using full pages for L1 and L2 page
tables. This is needed to support RDMA functionality on 57500 chips
since RDMA requires more context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier, some of the firmware commands (ex: CFA_FLOW_*) which are processed
by KONG processor were sent to the CHIMP processor from the host. This
approach was taken as there was no direct message channel to KONG.
CHIMP in turn used to send them to KONG. Newer firmware supports a new
message channel which the host can send messages directly to the KONG
processor.
This patch adds support for required changes needed in the driver
to support direct KONG message channel. This speeds up flow related
messages sent to the firmware for CLS_FLOWER offload.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These routines will be enhanced in the subsequent patch to
return the 2nd firmware comm. channel's hwrm response address &
sequence id respectively.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing
arithmetic.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding a 2nd communication channel to firmware.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set hwrm_intr_seq_id value to its inverted value instead of
HWRM_SEQ_INVALID, when an hwrm completion of type
CMPL_BASE_TYPE_HWRM_DONE is received. This will enable us to use
the complete 16-bit sequence ID space.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major changes are in the flow offload firmware APIs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_MLX5_ESWITCH is not defined, test for SR-IOV being disabled,
instead of calling e-switch LAG prereq routine.
Since LAG with SRIOV is allowed only when switchdev mode is on.
Fixes: eff849b2c6 ("net/mlx5: Allow/disallow LAG according to pre-req only")
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
vport system image guid should be queried using vport nic API for
Ethernet ports, and vport hca API for Infiniband ports.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Generate encap header depending on the routed device to support
native/tagged Ethernet header.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support generation of native or tagged Ethernet header for encap
header, depending on provided net device.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change the order to first route IPv4/6 and return if error. Only after
successful route continue to allocate an encap header, with no
functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In tunnel encap we prepare the encap header for IPv4/6 cases, in two
separate functions. For ETH header generation the code is almost
duplicated.
Move the ETH header generation code from IPv4/6 functions to a helper
function, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we don't support nor fail attempts to offload encap flows routed
to vlan device on the underlay network. We wrongly consider a vlan underlay
device to be on the same e-switch b/c the switchdev ID is retrieved recursively.
Add explicit check for that and fail such attempts.
Also align to a more strict check for the ingress and the underlay devices
to practically be on the same eswitch.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Fixes: 3e621b19b0 ('net/mlx5e: Support TC encapsulation offloads with upper devices')
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For tunnel we determine the output devs for IPv4/6 cases, in two
separate functions, with a duplicated code.
Move that code from IPv4/6 functions to a helper function, with no
functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We use the switchdev parent HW id helper to identify if the mirred device
shares the same ASIC/port with the ingress device. This can get us wrong
in the presence of upper devices such as vlan or bridge set over the HW
devices (VF or uplink representors), b/c the switchdev ID is retrieved
recursively.
To fail offload attempts in such cases, we condition the check on the
egress device to have not only the same switchdev ID but also the relevant
mlx5 netdev ops.
Fixes: 03a9d11e6e ('net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads')
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There are cases (e.g tunneling with vlan on underlay and potentially
more) where this makes sense, so allow that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The default size for the VF representors' SQ was too small to handle high
packet rates. Doubling the size from 64 to 128 drastically improves the
packet rate under stress (by about 50%), whereas increasing the size
beyond 128 has not shown to make any further difference.
The impact of the SQ size was measured with UDP traffic, in the following
topology: TG <-> PF <-> TC forwarding <-> VF representor <-> VF in VM
over a single core processing bi-directional traffic, with the following
results:
SQ size of 64: SQ size of 128:
Packet rate for 64B UDP packets: 860 [Kpps] 1280 [Kpps]
Packet rate for 114B VxLan
encapsulated UDP packets: 320 [Kpps] 500 [Kpps]
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Read the system time right before and immediately after reading the low
register of the internal timer. This adds support for the
PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The timecounter needs to be updated at least once in half of the
cyclecounter interval to prevent timecounter_cyc2time() interpreting a
new timestamp as an old value and causing a backward jump.
This would be an issue if the timecounter multiplier was so small that
the update interval would not be limited by the 64-bit overflow in
multiplication.
Shorten the calculated interval to make sure the timecounter is updated
in time even when the system clock is slowed down by up to 10%, the
multiplier is increased by up to 10%, and the scheduled overflow check
is late by 15%.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ariel Levkovich <lariel@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch removes the redundant variable initialization,
as driver will devm_kzalloc to set value to hdev soon.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver gets rss information from the last descriptor of the packet.
When driver handle the rss type, ring->next_to_clean indicates the
first descriptor of next packet.
This patch fix the descriptor index with "ring->next_to_clean - 1".
Fixes: 232fc64b6e ("net: hns3: Add HW RSS hash information to RX skb")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables flow director, all the rules will be disabled. But
when reset happens, it will restore all the rules again. It's not
reasonable. This patch fixes it by add flow director status check before
restore fules.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Fixes: c17852a893 ("net: hns3: Add support for enable/disable flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When add flow director fule for vf, the vf id is used as array
subscript before valid checking, which may cause memory overflow.
Fixes: dd74f815dd ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN operation, the driver will reclaim the memory which has
already used for TX. If the hardware is processing this memory, it will
cause a RCB error to the hardware. According the hardware's description,
the driver should reset the tqp before reclaim the memory during DOWN.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each pf supports max 64 vectors and 128 tqps. For 2p/4p core scenario,
there may be more than 64 cpus online. So the result of min_t(u16,
num_Online_cpus(), tqp_num) may be more than 64. This patch adds check
for the vector number.
Fixes: dd38c72604 ("net: hns3: fix for coalesce configuration lost during reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udelay() in driver may always occupancy processor. If there is only
one cpu in system, the VF driver may initialize fail when insmod
PF and VF driver in the same system. This patch use msleep() to free
cpu when VF wait PF message.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, default tc value is set to the max tc. It's more
reasonable to close tc by changing default tc value to 1. Users can
enable it with lldp tool when they want to use tc.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When triggering nic down, there is a time window between bringing down
the protocol stack and stopping the work task. If the net is up in the
time window, it may bring up the protocol stack again.
This patch fixes it by stop the work task at the beginning of
hns3_nic_net_stop(). To keep symmetrical, start the work task at the
end of hns3_nic_net_open().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect':
drivers/net/wireless/ath/wil6210/main.c:407:23: warning:
variable 'wdev' set but not used [-Wunused-but-set-variable]
It never used since commit ("e1b43407c034 wil6210: refactor disconnect flow")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is not an unexpected condition, so we don't need to be shouting to the
world about it.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath6kl was reworked to share code between regular and scheduled scans
in commit 3b8ffc6a22 ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.
Fixes: dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a break at the end of the ini tlv case.
Fix both the internal and external tlv parsing.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bump the API version to 43 for 9000 and 22000 devices.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debug data to the warning issued when getting wrong region
id from firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is needed to test TWT requester on the client side.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These macros are never used and are actually wrong, so it's very
confusing. Remove them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the rt status of the last assert or 0 if the dump collection was
not initiated by an assert. Add the number of rx and tx fifos in use.
These fields are added to dump info lst file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, due to SCD bug, we need to start the queue with an
higher SSN. The queue allocation function currently increments
the SSN in the packet itself, but it is pointless, since this
value is overridden later by iwl_mvm_tx_mpdu with the value
from mvmsta->tid_data[tid].seq_number. Updating tid data is
sufficient.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reclaim code, we don't need to take the queue lock for
waking the queue. The code section is executed only when
the tx path is stopped, and since the reclaim path is not
executed in parallel to itself, no one can update the queue
pointers, and accessing them is safe without a lock.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to lock mvm station for transport reclaim.
Move the locking down, after the reclaim.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HE capabilities differ between AP and STA.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's not the iwlwifi module that depends on mac80211, but iwlmvm and
iwldvm. To reflect this better, make MVM and DVM Kconfig options
depend on MAC80211 instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW expects to get the ppe value for each NSS-BW pair in the same
format as in the he phy capabilities IE, which means that a value of 0
implies ppe should be used for BPSK (mcs 0). If there are no PPE
thresholds in the IE, or if for some NSS-RU pair there's no threshold
set for it (this could happen because it's a variable-sized field), it
means no PPE should not be used for that pair, so the value sent to FW
should be 7 which corresponds to "none".
Fixes: 514c30696f ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the coupling of station id and queue id clear. Group code
together. Remove outdated comment. Never use an undefined hw
queue as given from mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Assigning mvmsta to be NULL when we are about to exit the
function is pointless. Remove it. Move the variable declaration
to the scope it is used.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
the AP station was supposed to be used for multicast frames
instead of the auxiliary station to avoid frames possibly
sent to an absent P2P GO. However, when moving to DQA mode,
this was broken as no valid queue was assigned. This is fixed
by a recent patch that directs all non-offchannel traffic to
ap station earlier in the TX path. However, the broken, and
now dead code, remained. Remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When building AMSDU for gen2, code uses iwl_tx_cmd. The only
updated field is len, which is in the same location, so it
is not a bug. However, it is a bit confusing and error prone,
so change it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function cw1200_bss_info_changed() and cw1200_hw_scan() can be
concurrently executed.
The two functions both access a possible shared variable "frame.skb".
This shared variable is freed by dev_kfree_skb() in cw1200_upload_beacon(),
which is called by cw1200_bss_info_changed(). The free operation is
protected by a mutex lock "priv->conf_mutex" in cw1200_bss_info_changed().
In cw1200_hw_scan(), this shared variable is accessed without the
protection of the mutex lock "priv->conf_mutex".
Thus, concurrency use-after-free bugs may occur.
To fix these bugs, the original calls to mutex_lock(&priv->conf_mutex) and
mutex_unlock(&priv->conf_mutex) are moved to the places, which can
protect the accesses to the shared variable.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
the Raspberry Pi 3 A+ (BCM43455) isn't able to operate in AP mode with
hostapd (device_ap_sme=1 use_monitor=0):
brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -52
So add the missing mgmt_stypes for AP mode to fix this.
Fixes: 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150e this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150e ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tristram Ha