Commit Graph

93 Commits

Author SHA1 Message Date
Li Jun 79742351c8 usb: chipidea: set usb otg capabilities
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.

Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-29 09:59:21 -05:00
Li Jun 9b6567e19b usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.

This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d usb: udc: add usb_udc_vbus_handler
dfea9c9 usb: udc: store usb_udc pointer in struct usb_gadget

Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.

This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git

Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
2015-04-08 14:13:02 +08:00
Greg Kroah-Hartman 1c41a9570a usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
 of 111 non-merge commits.
 
 Other than the usual set of cleanups and non-critical
 fixes, we have some interesting work for AM335x's MUSB
 babble recovery. Now that takes a lot less time and we
 don't have to Reset MUSB all the time.
 
 The printer gadget has been converted to configfs interface
 and the atmel udc has learned suspend/resume with wakeup.
 
 Signed-off-by: Felipe Balbi <balbi@ti.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVEZlvAAoJEIaOsuA1yqREvPMP/1dxQ6ufjkfmBmeZWiDWmwQs
 uoLskjNqVlnmcjWdasEwUSKMJMYfxNAmabYCx7ZWdmcDi0FNvmrjSfXqmM5uG5bF
 UKgP/7KbiK9WSRAcAuFEqYCMcAoH2CcLhlZ7BF7Peo+WxeQrh0A4ZPxh4VVJI2D4
 47/bpXFqPydVZyZurpfB0QA1r5jjsG+tJdP/LJKv6/g38XSBs4cgFUzzBWDN8212
 YVKlCiRWRwnCOrYFP1pf/gR4SM8UF4Vd+lDZ28JnwcxCmTKKMhAAoHjgckV6UctW
 Ur+hshsuvPwFWm9Rqp77TnO37LranaFUR2W2cBUGiPSZaUeXsdOhORpT+S64nuZi
 ZEw4qp9QlRwH8wCBT0m/Uozv+CZ7VP41hjYdFpcUevd/XLPQjx1ddn032jGYsrtC
 o+drLGtuULimusf/14zs1X4ejLdeYy6f0hLzqyDS8zTHAjToAmrM3Uw9nQWxWauB
 rHdTYMrgMGoolnIFVSLgR6xbGMu9wCYexylKFwVWEV6xrj4ZgpoVitUGg5DphCQy
 FdEepkeWgAUTcYC3wcIUHHC9wVS3YgPWRmyKjnh65kIFDGjPjHMK1eW06RGuhld/
 A92UJNIga34RtUXSUrcuwRBtWY+pDE/6XxppqzxTKAMjT9HV8JNPZGHu+2nKP0kp
 qu9PqszUGOyCuTG9+A+E
 =U+M2
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.1 merge window

As usual, a big pile of commits. This time a total
of 111 non-merge commits.

Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.

The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-24 22:57:49 +01:00
Greg Kroah-Hartman cd0e075784 Merge 4.0-rc5 into usb-next
We want the USB fixes in here as well to resolve merge conflicts.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-23 21:49:37 +01:00
Peter Chen 467a78c82a usb: chipidea: udc: apply new usb_udc_vbus_handler interface
It can move all pullup/pulldown operation control to udc-core
through usb_gadget_connect/usb_gadget_disconnect according to
vbus status.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-19 11:26:19 -05:00
Sanchayan Maity 06bdfcdb13 usb: chipidea: Add errata for revision 2.40a
At chipidea revision 2.40a, there is a below errata:

9000531823  B2-Medium  Adding a dTD to a Primed Endpoint May Not Get Recognized

Title: Adding a dTD to a Primed Endpoint May Not Get Recognized

Impacted Configuration: All device mode configurations.

Description:
There is an issue with the add dTD tripwire semaphore (ATDTW bit in USBCMD register)
that can cause the controller to ignore a dTD that is added to a primed endpoint.
When this happens, the software can read the tripwire bit and the status bit at '1'
even though the endpoint is unprimed.

After executing a dTD, the device controller endpoint state machine executes a final
read of the dTD terminate bit to check if the application added a dTD to the linked
list at the last moment. This read is done in the finpkt_read_latest_next_td (44) state.
After the read is performed, if the terminate bit is still set, the state machine moves
to unprime the endpoint. The decision to unprime the endpoint is done in the
checkqh_decision (59) state, based on the value of the terminate bit.
Before reaching the checkqh_decision state, the state machine traverses the
writeqhtd_status (57), writeqh_status (56), and release_prime_mask (42) states.
As shown in the waveform, the ep_addtd_tripwire_clr signal is not set to clear
the tripwire bit in these states.

Workaround:
The software must implement a periodic poll cycle, and check for each dTD
pending on execution (Active = 1), if the enpoint is primed. It can do this by reading
the corresponding bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are
read at 0, the software needs to re-prime the endpoint by writing 1 to the corresponding
bit in the ENDPTPRIME register. This can be done for every microframe, every frame or
with a larger interval, depending on the urgency of transfer execution for the application.

Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18 16:19:10 +01:00
Peter Chen d5d1e1bed4 usb: chipidea: udc: return immediately if re-enable non-empty endpoint
Some gadget driver (like uac1) will try to enable endpoint again even
the ep is not empty, it will cause the ep reset again and may affect
the dTD list which has already queued.

It returns -EBUSY immediately, and indicate the endpoint is in use.
In this way, the ep's behavior will not be affected, and the gadget
driver is also notified.

Cc: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-18 16:19:08 +01:00
Li Jun d20f780799 usb: chipidea: otg: add a_alt_hnp_support response for B device
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.

[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[    2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[    2.293105] usb 1-1: can't set HNP mode: -32
[    2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[    2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[    2.466424] usb 1-1: can't set HNP mode: -32
[    2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[    2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[    2.636436] usb 1-1: can't set HNP mode: -32
[    2.641003] usb usb1-port1: unable to enumerate USB device

Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-15 10:27:20 +01:00
Peter Chen 1009f9a36d usb: chipidea: udc: add set_selfpowered gaget ops
The gadget power property will be used at get_status request.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-29 10:32:37 -06:00
Peter Chen 5b1573005a usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
The hw_device_reset is dedicated to be used at device mode initializaiton,
so delete the parameter 'mode'. For host driver, the ehci driver will
handle all things.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-26 09:28:12 -08:00
Peter Chen afbe47758a usb: chipidea: gadget: use udc-core's reset notifier
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-10 17:19:35 -06:00
Antoine Tenart ef44cb4226 usb: allow to supply the PHY in the drivers when using HCD
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03 10:02:50 -06:00
Felipe Balbi 22835b807e usb: gadget: remove unnecessary 'driver' argument
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.

This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.

[1] http://markmail.org/message/x5zneg4xea4zntab

Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03 10:01:16 -06:00
Michal Sojka 304f7e5e1d usb: gadget: Refactor request completion
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.

All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.

Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-25 16:58:50 +02:00
Abbas Raza 953c664697 usb: chipidea: udc: Disable auto ZLP generation on ep0
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller

1) is implemented in UDC driver and it attaches ZLP to IN packet if
   descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH

When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then

        if (hwreq->req.zero && hwreq->req.length
            && (hwreq->req.length % hwep->ep.maxpacket == 0))
                add_td_to_list(hwep, hwreq, 0);

Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)

Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)

According to USB2.0 specs:

    8.5.3.2 Variable-length Data Stage
    A control pipe may have a variable-length data phase in which the
    host requests more data than is contained in the specified data
    structure. When all of the data structure is returned to the host,
    the function should indicate that the Data stage is ended by
    returning a packet that is shorter than the MaxPacketSize for the
    pipe. If the data structure is an exact multiple of wMaxPacketSize
    for the pipe, the function will return a zero-length packet to indicate
    the end of the Data stage.

In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.

In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.

So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.

Cc: stable@vger.kernel.org
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-17 16:51:22 -07:00
Peter Chen e4adcff09c usb: chipidea: udc: delete td from req's td list at ep_dequeue
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.

We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:

--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN                  = 0x0
INFO
|----- CBW Flags                = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length           = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed:  error=80004000

Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-01 23:06:02 -07:00
Peter Chen 10775eb17b usb: chipidea: udc: update gadget states according to ch9
Update device states according to ch9 in USB 2.0 specification

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-23 11:36:44 +09:00
Peter Chen 2dbd633f3a usb: chipidea: udc: delete useless code
Delete useless code

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-23 11:35:01 +09:00
Li Jun 4dcf720c5d usb: chipidea: OTG HNP and SRP fsm implementation
USB OTG interrupt handling and fsm transitions according to USB OTG
and EH 2.0.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:56:35 -07:00
Li Jun 95f5555fa0 usb: chipidea: udc: driver update for OTG HNP
Add b_hnp_enable request handling and enable gadget->is_otg

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:56:35 -07:00
Li Jun 36304b0616 usb: chipidea: export interrupt enable and status register read functions
This patch moves usb interrupt enable and status register read functions
from udc driver to core driver to use them in all ci drivers.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:56:34 -07:00
Li Jun 0c33bf781a usb: chipidea: operate on otgsc register in a general way
Use a more general way to read and write otgsc register.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:56:34 -07:00
Peter Chen d7b00e310b usb: chipidea: udc: refine isr_tr_complete_handler
Matthieu CASTET and Michael Grzeschik mentioned isr_tr_complete_handler
is a bit messy at below:
http://marc.info/?l=linux-usb&m=139047775001152&w=2

This commit creates a new function isr_setup_packet_handler to handle
setup packet, it makes isr_tr_complete_handler easy to read.

This is no functional change at this commit, tested with g_mass_storage
and g_ether.

Cc: Michael Grzeschik <mgr@pengutronix.de>
Cc: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-12 12:32:21 -07:00
Peter Chen 64fc06c40e usb: chipidea: udc: refine ep operation at isr_tr_complete_handler
- delete the warning message at interrupt handler, and adds judgement at
ep_enable, if non-ep0 requests ctrl transfer, it will indicate an error.
- delete hw_test_and_clear_setup_status which is a broken code
- Tested with g_mass_storage, g_ncm, g_ether

Cc: matthieu.castet@parrot.com
Reported-by: Michael Grzeschik <mgr@pengutronix.de>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Tested-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-24 17:07:52 -08:00
Peter Chen c859aa65a7 usb: chipidea: refine PHY operation
- Delete global_phy due to we can get the phy from phy layer now
- using devm_usb_get_phy to instead of usb_get_phy
- delete the otg_set_peripheral, which should be handled by otg layer

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-24 17:07:52 -08:00
Matthieu CASTET 5bf5dbeda2 usb: chipidea: need to mask when writting endptflush and endptprime
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.

Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-21 12:34:45 -08:00
Peter Chen 2fc5a7dace usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".

The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.

We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).

Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.

For stable tree: 3.11+.

Cc: stable <stable@vger.kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-13 15:55:19 -08:00
Felipe Balbi e90b8417af Linux 3.13-rc5
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.15 (GNU/Linux)
 
 iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
 9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
 9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
 FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
 47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
 cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
 =+Hcn
 -----END PGP SIGNATURE-----

Merge tag 'v3.13-rc5' into next

Linux 3.13-rc5

* tag 'v3.13-rc5': (231 commits)
  Linux 3.13-rc5
  aio: clean up and fix aio_setup_ring page mapping
  aio/migratepages: make aio migrate pages sane
  aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
  Don't set the INITRD_COMPRESS environment variable automatically
  mm: fix build of split ptlock code
  pstore: Don't allow high traffic options on fragile devices
  mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
  mm: page_alloc: revert NUMA aspect of fair allocation policy
  Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
  mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
  qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
  target: Remove extra percpu_ref_init
  arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
  ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
  target/file: Update hw_max_sectors based on current block_size
  iser-target: Move INIT_WORK setup into isert_create_device_ib_res
  iscsi-target: Fix incorrect np->np_thread NULL assignment
  mm/hugetlb: check for pte NULL pointer in __page_check_address()
  fix build with make 3.80
  ...

Conflicts:
	drivers/usb/phy/Kconfig
2013-12-23 11:22:46 -06:00
Robert Baldyga e117e742d3 usb: gadget: add "maxpacket_limit" field to struct usb_ep
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.

For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().

Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.

This patch modifies UDC drivers by adding support for maxpacket_limit.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-12-17 13:17:41 -06:00
Peter Chen 5a1e1456fc usb: chipidea: fix nobody cared IRQ when booting with host role
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.

This patch is needed for 3.12 stable

Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-09 13:14:12 -08:00
Peter Chen 65b2fb32b5 usb: chipidea: udc: Fix calling spin_lock_irqsave at sleep context
Fixing the below dump:

root@freescale ~$ modprobe g_serial
g_serial gadget: Gadget Serial v2.4
g_serial gadget: g_serial ready
BUG: sleeping function called from invalid context at /home/b29397/work/projects/upstream/usb/usb/drivers/base/power/runtime.c:952
in_atomic(): 1, irqs_disabled(): 128, pid: 805, name: modprobe
2 locks held by modprobe/805:
 #0:  (udc_lock){+.+.+.}, at: [<7f000a74>] usb_gadget_probe_driver+0x44/0xb4 [udc_core]
 #1:  (&(&ci->lock)->rlock){......}, at: [<7f033488>] ci_udc_start+0x94/0x110 [ci_hdrc]
irq event stamp: 3878
hardirqs last  enabled at (3877): [<806b6720>] _raw_spin_unlock_irqrestore+0x40/0x6c
hardirqs last disabled at (3878): [<806b6474>] _raw_spin_lock_irqsave+0x2c/0xa8
softirqs last  enabled at (3872): [<8002ec0c>] __do_softirq+0x1c8/0x2e8
softirqs last disabled at (3857): [<8002f180>] irq_exit+0xbc/0x110
CPU: 0 PID: 805 Comm: modprobe Not tainted 3.11.0-next-20130910+ #85
[<80016b94>] (unwind_backtrace+0x0/0xf8) from [<80012e0c>] (show_stack+0x20/0x24)
[<80012e0c>] (show_stack+0x20/0x24) from [<806af554>] (dump_stack+0x9c/0xc4)
[<806af554>] (dump_stack+0x9c/0xc4) from [<8005940c>] (__might_sleep+0xf4/0x134)
[<8005940c>] (__might_sleep+0xf4/0x134) from [<803a04a4>] (__pm_runtime_resume+0x94/0xa0)
[<803a04a4>] (__pm_runtime_resume+0x94/0xa0) from [<7f0334a4>] (ci_udc_start+0xb0/0x110 [ci_hdrc])
[<7f0334a4>] (ci_udc_start+0xb0/0x110 [ci_hdrc]) from [<7f0009b4>] (udc_bind_to_driver+0x5c/0xd8 [udc_core])
[<7f0009b4>] (udc_bind_to_driver+0x5c/0xd8 [udc_core]) from [<7f000ab0>] (usb_gadget_probe_driver+0x80/0xb4 [udc_core])
[<7f000ab0>] (usb_gadget_probe_driver+0x80/0xb4 [udc_core]) from [<7f008618>] (usb_composite_probe+0xac/0xd8 [libcomposite])
[<7f008618>] (usb_composite_probe+0xac/0xd8 [libcomposite]) from [<7f04b168>] (init+0x8c/0xb4 [g_serial])
[<7f04b168>] (init+0x8c/0xb4 [g_serial]) from [<800088e8>] (do_one_initcall+0x108/0x16c)
[<800088e8>] (do_one_initcall+0x108/0x16c) from [<8008e518>] (load_module+0x1b00/0x20a4)
[<8008e518>] (load_module+0x1b00/0x20a4) from [<8008eba8>] (SyS_init_module+0xec/0x100)
[<8008eba8>] (SyS_init_module+0xec/0x100) from [<8000ec40>] (ret_fast_syscall+0x0/0x48)

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-11 16:25:15 -07:00
Peter Chen a3aee3687d usb: chipidea: udc: Fix spinlock recursion during bus reset
After configuration, the host also possible sends bus reset
at any time, at such situation, it will trigger below spinlock
recursion dump. This commit unlocks the spinlock before calling
gadget's disconnect.

BUG: spinlock recursion on CPU#0, swapper/0/0
 lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106
[<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14)
[<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc)
[<805c143c>] (dump_stack+0x94/0xbc) from [<80282cf8>] (do_raw_spin_lock+0x16c/0x18c)
[<80282cf8>] (do_raw_spin_lock+0x16c/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c)
[<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110)
[<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial])
[<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm])
[<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite])
[<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite])
[<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4)
[<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164)
[<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c)
[<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c)
[<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168)
[<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c)
[<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4)
[<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c)
[<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54)
Exception stack(0x8083bf68 to 0x8083bfb0)
bf60:                   81533b80 00000000 00096234 8001d760 8088e12c 00000000
bf80: 8083a000 8083a000 8084290c 805cb414 808428ac 8083a000 00000001 8083bfb0
bfa0: 8000f138 8000f13c 60000013 ffffffff
[<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c)
[<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148)
[<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318)
BUG: spinlock lockup suspected on CPU#0, swapper/0/0
 lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106
[<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14)
[<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc)
[<805c143c>] (dump_stack+0x94/0xbc) from [<80282c94>] (do_raw_spin_lock+0x108/0x18c)
[<80282c94>] (do_raw_spin_lock+0x108/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c)
[<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110)
[<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial])
[<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm])
[<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite])
[<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite])
[<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4)
[<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164)
[<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c)
[<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c)
[<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168)
[<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c)
[<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4)
[<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c)
[<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54)
Exception stack(0x8083bf68 to 0x8083bfb0)
bf60:                   81533b80 00000000 00096234 8001d760 8088e12c 00000000
bf80: 8083a000 8083a000 8084290c 805cb414 808428ac 8083a000 00000001 8083bfb0
bfa0: 8000f138 8000f13c 60000013 ffffffff
[<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c)
[<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148)
[<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318)

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-11 16:25:14 -07:00
Peter Chen 74475ede78 usb: chipidea: move PHY operation to core
PHY operations are common, so move them to core.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-30 18:54:06 -07:00
Greg Kroah-Hartman df9b17f586 Merge 3.12-rc3 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-29 18:45:55 -07:00
Peter Chen e7ef5265b1 usb: chipidea: udc: free pending TD at removal procedure
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.

This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.

Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-25 17:30:36 -07:00
Peter Chen f84839daa7 usb: chipidea: udc: fix the oops after rmmod gadget
When we rmmod gadget, the ci->driver needs to be cleared.
Otherwise, when we plug in usb cable again, the driver will
consider gadget is there, and go to enumeration procedure,
but in fact, it was removed.

ci_hdrc ci_hdrc.0: Connected to host
Unable to handle kernel paging request at virtual address 7f02a42c
pgd = 80004000
[7f02a42c] *pgd=3f13d811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] SMP ARM
Modules linked in: usb_f_acm u_serial libcomposite configfs [last unloaded: g_serial]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0+ #42
task: 807dba88 ti: 807d0000 task.ti: 807d0000
PC is at udc_irq+0x8fc/0xea4
LR is at l2x0_cache_sync+0x5c/0x6c
pc : [<803de7f4>]    lr : [<8001d0f0>]    psr: 20000193
sp : 807d1d98  ip : 807d1d80  fp : 807d1df4
r10: af809900  r9 : 808184d4  r8 : 00080001
r7 : 00082001  r6 : afb711f8  r5 : afb71010  r4 : ffffffea
r3 : 7f02a41c  r2 : afb71010  r1 : 807d1dc0  r0 : afb71068
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 3f01804a  DAC: 00000017
Process swapper/0 (pid: 0, stack limit = 0x807d0238)
Stack: (0x807d1d98 to 0x807d2000)
1d80:                                                       00000000 afb71014
1da0: 000040f6 00000000 00000001 00000000 00007530 00000000 afb71010 001dcd65
1dc0: 01000680 00400000 807d1e2c afb71010 0000004e 00000000 00000000 0000004b
1de0: 808184d4 af809900 807d1e0c 807d1df8 803dbc24 803ddf04 afba75c0 0000004e
1e00: 807d1e44 807d1e10 8007a19c 803dbb9c 8108e7e0 8108e7e0 9ceddce0 af809900
1e20: 0000004e 807d0000 0000004b 00000000 00000010 00000000 807d1e5c 807d1e48
1e40: 8007a334 8007a154 af809900 0000004e 807d1e74 807d1e60 8007d3b4 8007a2f0
1e60: 0000004b 807cce3c 807d1e8c 807d1e78 80079b08 8007d300 00000180 807d8ba0
1e80: 807d1eb4 807d1e90 8000eef4 80079aec 00000000 f400010c 807d8ce4 807d1ed8
1ea0: f4000100 96d5c75d 807d1ed4 807d1eb8 80008600 8000eeac 8042699c 60000013
1ec0: ffffffff 807d1f0c 807d1f54 807d1ed8 8000e180 800085dc 807d1f20 00000046
1ee0: 9cedd275 00000010 8108f080 807de294 00000001 807de248 96d5c75d 00000010
1f00: 00000000 807d1f54 00000000 807d1f20 8005ff54 8042699c 60000013 ffffffff
1f20: 9cedd275 00000010 00000005 8108f080 8108f080 00000001 807de248 8086bd00
1f40: 807d0000 00000001 807d1f7c 807d1f58 80426af0 80426950 807d0000 00000000
1f60: 808184c0 808184c0 807d8954 805b886c 807d1f8c 807d1f80 8000f294 80426a44
1f80: 807d1fac 807d1f90 8005f110 8000f288 807d1fac 807d8908 805b4748 807dc86c
1fa0: 807d1fbc 807d1fb0 805aa58c 8005f068 807d1ff4 807d1fc0 8077c860 805aa530
1fc0: ffffffff ffffffff 8077c330 00000000 00000000 807bef88 00000000 10c53c7d
1fe0: 807d88d0 807bef84 00000000 807d1ff8 10008074 8077c594 00000000 00000000
Backtrace:
[<803ddef8>] (udc_irq+0x0/0xea4) from [<803dbc24>] (ci_irq+0x94/0x14c)
[<803dbb90>] (ci_irq+0x0/0x14c) from [<8007a19c>] (handle_irq_event_percpu+0x54/0x19c)
 r5:0000004e r4:afba75c0
 [<8007a148>] (handle_irq_event_percpu+0x0/0x19c) from [<8007a334>] (handle_irq_event+0x50/0x70)
[<8007a2e4>] (handle_irq_event+0x0/0x70) from [<8007d3b4>] (handle_fasteoi_irq+0xc0/0x16c)
 r5:0000004e r4:af809900
 [<8007d2f4>] (handle_fasteoi_irq+0x0/0x16c) from [<80079b08>] (generic_handle_irq+0x28/0x38)
 r5:807cce3c r4:0000004b
 [<80079ae0>] (generic_handle_irq+0x0/0x38) from [<8000eef4>] (handle_IRQ+0x54/0xb4)
 r4:807d8ba0 r3:00000180
 [<8000eea0>] (handle_IRQ+0x0/0xb4) from [<80008600>] (gic_handle_irq+0x30/0x64)
 r8:96d5c75d r7:f4000100 r6:807d1ed8 r5:807d8ce4 r4:f400010c
 r3:00000000
 [<800085d0>] (gic_handle_irq+0x0/0x64) from [<8000e180>] (__irq_svc+0x40/0x54)
Exception stack(0x807d1ed8 to 0x807d1f20)
1ec0:                                                       807d1f20 00000046
1ee0: 9cedd275 00000010 8108f080 807de294 00000001 807de248 96d5c75d 00000010
1f00: 00000000 807d1f54 00000000 807d1f20 8005ff54 8042699c 60000013 ffffffff
 r7:807d1f0c r6:ffffffff r5:60000013 r4:8042699c
 [<80426944>] (cpuidle_enter_state+0x0/0xf4) from [<80426af0>] (cpuidle_idle_call+0xb8/0x174)
 r9:00000001 r8:807d0000 r7:8086bd00 r6:807de248 r5:00000001
 r4:8108f080
 [<80426a38>] (cpuidle_idle_call+0x0/0x174) from [<8000f294>] (arch_cpu_idle+0x18/0x5c)
[<8000f27c>] (arch_cpu_idle+0x0/0x5c) from [<8005f110>] (cpu_startup_entry+0xb4/0x148)
[<8005f05c>] (cpu_startup_entry+0x0/0x148) from [<805aa58c>] (rest_init+0x68/0x80)
 r7:807dc86c
 [<805aa524>] (rest_init+0x0/0x80) from [<8077c860>] (start_kernel+0x2d8/0x334)
[<8077c588>] (start_kernel+0x0/0x334) from [<10008074>] (0x10008074)
Code: e59031e0 e51b203c e24b1034 e2820058 (e5933010)
---[ end trace f874b2c5533c04bc ]---
Kernel panic - not syncing: Fatal exception in interrupt

Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-25 17:30:29 -07:00
Peter Chen 92b336d7f6 usb: chipidea: udc: Consolidate the call of disconnect
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.

Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-25 17:23:27 -07:00
Peter Chen 4a29567b77 chipidea: udc: free pending TD at removal procedure
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.

This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-25 17:20:52 -07:00
Peter Chen 4a64783b66 usb: chipidea: udc: .pullup is valid only when vbus is there
For chipidea, the IP must know vbus before the controller
begins to run. So the .pullup should only be called when
the vbus is there.

Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-14 12:37:20 -07:00
Peter Chen d268e9bc23 usb: chipidea: retire flag CI_HDRC_PULLUP_ON_VBUS
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-14 12:37:20 -07:00
Peter Chen e7e621eb84 usb: chipidea: udc: fix misuse of REGS_SHARED and PULLUP_ON_VBUS flags
CI_HDRC_REGS_SHARED stands for the controller registers is shared
with other USB drivers, if all USB drivers are at chipidea/, it doesn't
needed to be set.
CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This
flag doesn't need to be set if the vbus is always on for gadget
since dp has always pulled up after the gadget has initialized.

So, the current code seems to misuse this two flags.
- When the gadget initializes, the controller doesn't need to run if
it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to
shared register.
- When the gadget starts (load one gadget module), the controller
can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not
relate to shared register.

Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-14 12:37:20 -07:00
Peter Chen a107f8c505 usb: chipidea: add vbus interrupt handler
We add vbus interrupt handler at ci_otg_work, it uses OTGSC_BSV(at otgsc)
to know it is connect or disconnet event.
Meanwhile, we introduce two flags id_event and b_sess_valid_event to
indicate it is an id interrupt or a vbus interrupt.

Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-14 12:37:20 -07:00
Peter Chen 3f124d233e usb: chipidea: add role init and destroy APIs
- The role's init will be called at probe procedure.
- The role's destroy will be called at fail patch
at probe and driver's removal.
- The role's start/stop will be called when specific
role has started.

Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-14 12:37:19 -07:00
Peter Chen d66895f9df usb: chipidea: udc: otg_set_peripheral is useless for some chipidea users
It is useless at below cases:
- If we implement both usb host and device at chipidea driver.
- If we don't need phy->otg.

Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-08-14 12:37:19 -07:00
Alexander Shishkin 8e22978c57 usb: chipidea: drop "13xxx" infix
"ci13xxx" is bad for at least the following reasons:
  * people often mistype it
  * it doesn't add any informational value to the names it's used in
  * it needlessly attracts mail filters

This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.

Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-24 16:16:55 -07:00
Alexander Shishkin 2dbc5c4c83 usb: chipidea: get rid of camelcase names
Since someone has added camelcase detection to checkpatch.pl, chipidea
udc patches have been very noisy. To make everybody's life easier, this
patch changes camelcase names into something more appropriate to the
coding style. No functional changes.

Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-17 13:47:25 -07:00
Michael Grzeschik 2e27041296 usb: chipidea: udc: add multiple td support to hardware_{en,de}queue
This patch removes the restriction of having a limited amount of only
four active tds on one endpoint. We use the linked list implementation
to manage all tds which get added and removed by hardware_{en,de}queue.

The removal of this restriction adds the driver to run into a hardware
errata. It's possible that the hardware will still address an transfer
descriptor that already got cleaned up. To solve this the patch also
postpone the cleanup of processed tds by one.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-17 13:45:47 -07:00
Michael Grzeschik cc9e6c495b usb: chipidea: udc: manage dynamic amount of tds with a linked list
Instead of having a limited number of usable tds in the udc we use a
linked list to support dynamic amount of needed tds for all special
gadget types. This improves throughput.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-17 13:45:47 -07:00
Michael Grzeschik e4ce4ecd96 usb: chipidea: udc: configure iso endpoints
This patch adds iso endpoint support to the device controller.
It makes use of the multiplication bits in the maxpacket field
of the endpoint and calculates the multiplier bits for each
transfer description on every request.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-17 13:45:46 -07:00
Alexander Shishkin d343f4e8d6 usb: chipidea: fix no transceiver case
Since usb phy code does return ERR_PTR() values, make sure that we don't
end up dereferencing them. This is a problem, for example, on platforms
that don't register a phy for chipidea since b7fa5c2a ("usb: phy: return
-ENXIO when PHY layer isn't enabled").

Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-11 16:18:04 -07:00