Add BYT_RT5651_JD_NOT_INV quirk for devices with an inverted
(active-high instead of the normal active-low) jack-detect switch.
And add a quirk for the Complet Electro Serv MY8307 tablet which has
an inverted jack-detect switch (and a mono-speaker).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If playback and capture are enabled concurrently, when the capture stops
the output becomes inaudile. The playback application will become stuck
and underrun after a timeout.
This is caused by mistaken use of the stream_id, which should only be
set for playback and not for capture
Tested on Apollolake and Kabylake with SST driver.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx3z7ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H5QB/9jwKEwOdk6ynoFUpQwXPPkQl7CGkIh
P8J3OMTt+U4FNOrVG2S7xgUl69ZoaLm9rS/PHVrMV5krSLqY//2CTvF068qDBBlj
haBxgeRbe4pwLZPfFUnWvn6v1rdvNCXzDG/be9jGPJjDcm6wK44VJQWkPbqTsh6O
ZORqvKn48D89W0DegG1B+4jvbietPkhA0+nHQXwsWZ+sfMcEV/AWWsE5FIQ7ucCC
bundBBncUFKMMp9whuhj2W9FO62LUd8OAM7ejis3hfKk9MsQWUy6vrcN1XgRCq47
4I0doB5o+WhsOGMTZMcuhFISCVaCDqbNqGuVbeK0sdonjc1xz0682jLo
=9rq8
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More changes for v5.1
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
This patch enables the reuse of kbl_da7219_max98927 machine driver to
support max98373. The same machine driver is modified for cases where one
amplifier is swapped out with another. Most of the changes are about
renaming the codec and codec_dai names, with minor differences due to
support for 24 bits in one case and 16 in the other.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add FE DAI link to support parallel playback on 2 ports
simultaneously.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch enables support for GeminiLake with the DA7219 codec and
MAX98357A amplifier. To avoid duplicating code, the existing machine
driver for ApolloLake is reused with only changes in hardware
connectivity (SSP2 for DA7219 and SSP1 for MAX98357A).
The dailinks are directly modified in this patch. Using a helper would
be nicer, but it'll be done in a follow-up step with validation done
across multiple machine drivers.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no risk of the module being removed while the platform
components are in use. This solves the problem of the snd_soc_skl
module not being removable with rmmod
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
New quirk enforces search for GPIO based on its type,
i.e. iterate over GpioIo resources only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxde0wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JWRB/9aQsLR22dNvKosiitTO/nnnPw/sUiG
cFZsI4G1mFpjXyC2azaY1MQOIjRZY3WDsRjcHtAJUkdJnz8fdyj74mIRoHrQI/yv
qdc7EtV5J0k0DemDQH2z5J7WjrkLg4aQCMT2XIvwrXL44jBv/iVKUE8l08D2AZ6t
hQiVIF/9iBnaJwqfUSKzJaufdd88Onh1dBljLGwZnRDtG9mndpxoi+S9pR6gwSMG
JzbgO4kUXdN95wKPxDsHFZimiSaX4bBo2cr79cisPrvcIKTyMAdtkAoNAcyuRezx
qiN2l4zz6Wxi8TygkBZfmWGKz2/2fMDWLvYwfEnA9PhddlSUZt/P1IPl
=tkEF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.1
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
snd_pcm_lib_preallocate_pages() and co always succeed, so the error
check is simply redundant. Drop it.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For some reason we test if the machine is passed as a parameter before
fixing up the codec name. This is unnecessary, generates false
positives in static analysis tools and done only in this machine
driver, remove and adjust indentation.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper to override dailink platform name, if passed as parameter
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const arrays on the stack but instead make
it static. Makes the object code smaller, for example:
Before:
text data bss dec hex filename
14107 8832 224 23163 5a7b bytcht_es8316.o
After:
text data bss dec hex filename
14015 8896 224 23135 5a5f bytcht_es8316.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a big batch of fixes here. There's a couple of things going on,
the main one is that we found some issues with not deferring probe when
we should, causing us to skip some driver initialization. The fixes for
this then in turn exposed some issues with how we were searching for
components which had previously gone unnoticed due to the original
issue.
There's also been the normal driver specific stuff and there's been what
looks like several batches of automated scanning for issues which have
generated quite a large set of smaller fixes for potential crashes and
missed error handling.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxBy/wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HNQB/wI7qx/bNGOX1p2C0M5ENdgsMcYDpMh
OHD073hL4wDkNJ/O2josnceCtrPUS5tuOxmx765IFXrAR4FWlNezQL4dHwTNGfG9
Femd6iAxv47lC2fROpuHfB0j32LIjVrHLYDG0wAiDvteXK2VrGbj8vedfWqflOBj
PX2kqkkgWfSCTrEYdrE09ExYoYKYdEqU/LEKFmIUnMuXc/HNHLo6e1sFNzTo8DIo
g5P8nQ//Qgi1U9UWMabKjy4lYL2Tcid9jcNlz0QIffK2qwIEpVBeuhqJaT4sQrf5
G51UrSk2y4lJ0t9WXv1SwQTDi2slCCGcOHA3fylGkJl1cxgOFMAR37Xs
=ev1L
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxCJZ0THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0L+2B/0VnSutpVWaJnGyBuJ6zrydcSIW4183
G51jmioR10cl5LDV0DiI9l7IoiOwUyODbrIl/swoQPs7FWUsFRGFYytdmAoqaKIC
HK1j4D6Tlzac++e6bP6G6NzBMW6TGTu8c7hu3UtIGCz5uPRUKBthnndHmSbEB4h+
10N7RMs9+/BvH1Zt+x9VqEIP5OHpwc7rP/8yANYbQCY7CPehqDiGpE7SvUgFFl5t
IHx0nM1lJNeJyeu0Z/9BGAB5GWM/DzuMSrppNwl2k/QujSSyf1EPZvThpYNCBbnQ
6cQ51+7SZi06ejzMBB5h5z/9yFZTSKmTwFwzJwg/fJ/QngZVkksRRNLV
=9LPf
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.0-rc2' into asoc-5.1
ASoC: Fixes for v5.0
Quite a big batch of fixes here. There's a couple of things going on,
the main one is that we found some issues with not deferring probe when
we should, causing us to skip some driver initialization. The fixes for
this then in turn exposed some issues with how we were searching for
components which had previously gone unnoticed due to the original
issue.
There's also been the normal driver specific stuff and there's been what
looks like several batches of automated scanning for issues which have
generated quite a large set of smaller fixes for potential crashes and
missed error handling.
Quite a big batch of fixes here. There's a couple of things going on,
the main one is that we found some issues with not deferring probe when
we should, causing us to skip some driver initialization. The fixes for
this then in turn exposed some issues with how we were searching for
components which had previously gone unnoticed due to the original
issue.
There's also been the normal driver specific stuff and there's been what
looks like several batches of automated scanning for issues which have
generated quite a large set of smaller fixes for potential crashes and
missed error handling.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlxBy/wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HNQB/wI7qx/bNGOX1p2C0M5ENdgsMcYDpMh
OHD073hL4wDkNJ/O2josnceCtrPUS5tuOxmx765IFXrAR4FWlNezQL4dHwTNGfG9
Femd6iAxv47lC2fROpuHfB0j32LIjVrHLYDG0wAiDvteXK2VrGbj8vedfWqflOBj
PX2kqkkgWfSCTrEYdrE09ExYoYKYdEqU/LEKFmIUnMuXc/HNHLo6e1sFNzTo8DIo
g5P8nQ//Qgi1U9UWMabKjy4lYL2Tcid9jcNlz0QIffK2qwIEpVBeuhqJaT4sQrf5
G51UrSk2y4lJ0t9WXv1SwQTDi2slCCGcOHA3fylGkJl1cxgOFMAR37Xs
=ev1L
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.0-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.0
Quite a big batch of fixes here. There's a couple of things going on,
the main one is that we found some issues with not deferring probe when
we should, causing us to skip some driver initialization. The fixes for
this then in turn exposed some issues with how we were searching for
components which had previously gone unnoticed due to the original
issue.
There's also been the normal driver specific stuff and there's been what
looks like several batches of automated scanning for issues which have
generated quite a large set of smaller fixes for potential crashes and
missed error handling.
Since the refactoring of HD-audio display power management, the
display power status is managed per domain. Meanwhile the ASoC
hdac_hdmi driver still keeps and relies (incorrectly) on the
refcounting together with ASoC skl driver, and this leads to the
display state always on.
This patch is an attempt to address the regression by simplifying the
PM code of ASoC skl and hdac_hdmi drivers. Basically, since the
refactoring, we don't have to manage the display power at HD-audio
controller suspend / resume but only at HD-audio HDMI codec suspend /
resume. So the patch drops the superfluous snd_hdac_display_power()
calls in skl driver.
Meanwhile, in hdac_hdmi side, we rewrite the PM call just to re-use
the runtime PM callbacks like other drivers do. Now the logic is
simple: turn off at suspend and turn on at resume.
The patch also fixes the possibly missing display-power off at skl
driver removal as well as some error paths at probe.
Fixes: 029d92c289 ("ALSA: hda: Refactor display power management")
Reported-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_byt_cht_es8316_mc_remove() use the platform drvdata as a type
of 'struct byt_cht_es8316_private', but snd_byt_cht_es8316_mc_probe()
set it to 'struct snd_soc_card', as suggested by Dan Carpenter, fix
the usage in snd_byt_cht_es8316_mc_remove().
Fixes: 0d3e91da07 ("ASoC: Intel: bytcht_es8316: Add external speaker mux support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
move the codec PLL to rt5682_codec_init, because codec only need to config the clock source/PLL once.
As the result, remove the platform_clock_controls since no need to control clock anymore.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a DMI quirk for the Point of View TAB-P1006W-232 (v1.0) tablet, this
tablet is special in a number of ways:
1) It uses the 2nd GPIO resource in the ACPI tables for jack-detect rather
then using the rt5651 codec's builtin jack-detect functionality
2) It uses the 3th GPIO resource in the ACPI tables to control the
external amplifier rather then the usual first non GpioInt resource and
the GPIO is active-low.
3) It is a BYTCR device, without a CHAN package and it uses SSP0-AIF1
rather then the default SSP0-AIF2.
4) Its internal mic is a digital mic (the first x86 rt5651 device that
I'm aware of which does this), combined with having its headset-mic
connected to IN2.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some board designs hook the jack-detect up to an external GPIO, rather
then to one of the codec pins, add support for this.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add quirks module parameter to allow manually specifying quirks
from the kernel commandline (or modprobe.conf).
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 37c7401e8c ("ASoC: Intel: bytcr_rt5651: Fix DMIC map
headsetmic mapping"), changed the headsetmic mapping from IN3P to IN2P,
this was based on the observation that all bytcr_rt5651 devices I have
access to (7 devices) where all using IN3P for the headsetmic. This was
an attempt to unifify / simplify the mapping, but it was wrong.
None of those devices was actually using a digital internal mic. Now I've
access to a Point of View TAB-P1006W-232 (v1.0) tabler, which does use a
DMIC and it does have its headsetmic connected to IN2P, showing that the
original mapping was correct, so this commit reverts the change changing
the mapping back to IN2P.
Fixes: 37c7401e8c ("ASoC: Intel: bytcr_rt5651: Fix DMIC map ... mapping")
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Point of View TAB-P1006W-232 (v1.0) tablet uses 10EC5640 as
ACPI HID, but it has a rt5651 codec add a quirk for this.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_lib_malloc_pages() may fail, so let's check its status and
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add quirks to select the correct input map, jack-detect options
and channel map to make sound work on the ASUS MeMO Pad 7 (ME176C).
Note: Although sound works out of the box, jack detection currently
requires overriding the ACPI DSDT table. This is necessary because
the rt5640 ACPI device (10EC5640) has the wrong GPIO listed as
interrupt (one of the Bluetooth GPIOs).
The correct GPIO is GPO2 0x0004 (listed as the first GPIO in the
Intel(R) Audio Machine Driver - AMCR0F28 device).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices detected as BYT-T by the PMIC-type based detection
have only a single IRQ listed in the 80860F28 ACPI device. This
causes -ENXIO later when attempting to get the IRQ at index 5.
It turns out these devices behave more like BYT-CR devices,
and using the IRQ at index 0 makes sound work correctly.
This patch adds a fallback for these devices to is_byt_cr():
If there is no IRQ resource at index 5, treating the device
as BYT-T is guaranteed to fail later, so we can safely treat
these devices as BYT-CR without breaking any working device.
Link: http://mailman.alsa-project.org/pipermail/alsa-devel/2018-December/143176.html
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_byt_cr() and its usage can be simplified by returning the bool
directly, instead of through a pointer. This works because the
return value is just treated as bytcr = false and is not used
otherwise.
This patch also removes the extra check of
IS_ENABLED(CONFIG_IOSF_MBI) in favor of checking
iosf_mbi_available() directly. The header already takes care
of returning false if the config option is not enabled.
No functional change.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some BYTCR devices use an ES8316 codec, add an ACPI match table entry
for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the input-map and on if 1 or 2 speakers are connected,
userspace needs to use a different UCM profile.
Since we already deal with quirks in the kernel driver and set the
input-map from the kernel, add a quirk for devices with a single / mono
speaker and set the card's long_name based on the input and speaker
quirks, so that userspace can use the long_name to pick the right UCM
profile.
This change, including how the long_name is build-up mirrors how we do
this in the bytcr_rt5640 and bytcr_rt5651 machine drivers.
Note since all devices I have access to use a mono speaker setup I've
chosen to default the speaker setting to mono.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After adding jack-detect support we have 3 microphone input switches:
"Microphone 1", "Microphone 2" and "Headset Mic". But the ES8316 has only
2 microphone inputs.
In the app-note explaining how to use the codec and on the 3 boards I
have one input is used for an internal microphone and one for the headset
microphone. On the 2 CHT boards I have the internal mic is on on MIC1 and
the headset mic is on MIC2, on the BYTCR board I have it is the other way
around.
This commit replaces the 2 "Microphone 1" and "Microphone 2" input switches
with a single "Internal Mic" switch and adds support for selecting either
possible input mapping.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ES8316 only has a single (amplified) output. The ES8316 appnote showing
the intended usage uses a jack-receptacle which physically disconnects the
speakers from the output when a jack is plugged in.
But all 3 devices using the es8316 which I have (2 Cherry Trail devices and
one Bay Trail CR device), use an analog mux to disconnect the speakers,
driven by a GPIO.
This commit adds support for this, modelling this as a separate speaker
widget / dapm pin-switch which sets the mux to drive the speakers when
selected.
The intend is for userspace to use the recently added jack-detect support
and then automatically select either the Headphone or Speaker output based
on that.
Note this commit includes a workaround for an ACPI table bug which is
present on 2 of the 3 devices I have, see the added comment in the code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hookup the jack-detect support added to the codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for having the codec connected to SSP0 instead of SSP2. This
is controlled through a new quirk parameter, similar to how this is done
in the bytcr_rt5640 and bytcr_rt5651 machine drivers.
Bay Trail CR (cost reduced) SoCs do not have an SSP2, so we default to SSP0
there.
Note the SPP0 quirk gets BIT(16) because bits 0-15 are reserved for non
boolean quirks like the input-map added in a later commit in this series.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some minor refactoring:
1) Group the code setting the card dev and prive pointers together with
registering the card
2) Properly put the comment about registering the card at the place where
we actually register the card and add a new comment for getting the clk
3) Add a struct device *dev helper variable (this will be used more in
follow up commits)
4) Reword error message to have the same "foo failed: %d" wording as others
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For lack of a better (non-random) way of sorting includes more and more
files in the kernel are moving over to sorting the includes alphabetically.
Move the bytcht_es8316 driver over to this sorting before we add a
bunch of more includes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix Sparse warnings with two machine drivers which weren't updated
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Detected with Coccinelle
skl-messages.c:419:5-32: WARNING: Comparison to bool
skl-pcm.c:1426:6-33: WARNING: Comparison to bool
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Detected with Coccinelle
sound/soc/intel/skylake/skl-topology.c:3106:16-20: WARNING: casting
value returned by memory allocation function to (char *) is useless.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After 'commit 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set")' dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly. This code relies on IOSF_MBI and IOSF_MBI depends
on PCI. For this reason, add a direct dependency on CONFIG_PCI to the
IOSF_MBI driver.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason this field was set to zero when all other drivers use
.dynamic = 1 for front-ends. This change was tested on Dell XPS13 and
has no impact with the existing legacy driver. The SOF driver also works
with this change which enables it to override the fixed topology.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This essentially reverts the commits
c337104b1a ("ALSA: HD-Audio: SKL+: abort probe if DSP is present
and Skylake driver selected")
and
d82b51c855 ("ALSA: HD-Audio: SKL+: force HDaudio legacy or SKL+
driver selection")
for the path of legacy HD-audio controller (snd-hda-intel).
The automatic DSP detection and skip of binding with the legacy driver
caused regressions on several machines like Dell XPS13. They give the
PCI class 0x40380 indicating the availability of DSP while they don't
work with ASoC SKL driver (yet).
As the support of ASoC driver for such devices isn't available, it's
better to revert the whole DSP-detection-and-skip behavior of the
legacy driver, so that we can get the old good driver working on such
devices.
The pci_binding option for ASoC SKL driver is still kept so that it
can work without blacklisting.
Fixes: c337104b1a ("ALSA: HD-Audio: SKL+: abort probe if DSP is present and Skylake driver selected")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Azat Khuzhin <dohardgopro@gmail.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HDaudio and Skylake drivers, add module parameter "pci_binding"
When pci_binding == 0 (AUTO), the PCI class/subclass info is used to
select drivers based on the presence of the DSP.
pci_binding == 1 (LEGACY) forces the use of the HDAudio legacy driver,
even if the DSP is present.
pci_binding == 2 (ASOC) forces the use of the ASOC driver. The
information on the DSP presence is bypassed.
The value for the module parameter needs to be identical for both
drivers. This parameter is intended as a back-up solution if the
automatic detection fails or when the DSP usage fails. Such cases
should be reported on the alsa-devel mailing list for analysis.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the SST/Skylake driver supports per platform selectors, we
can add logic to automatically select the right driver.
If the Skylake driver is selected for a specific platform, and the DSP
is detected at run-time based on the PCI class/subclass/prog-if
information, the legacy HDaudio driver aborts the probe. This will
result in a single driver probing and remove the need for modprobe
blacklists.
Follow-up patches will add a module parameter to bypass the logic if
this automatic detection fails, or if the Skylake driver is unable to
actually support the platform (firmware authentication, missing
topology file, hardware issue, etc).
The same mechanism will be used to conflicts generated by the same PCI
ID being registered by both legacy HDAuudio and SOF drivers for Intel
platforms. In other words SOF will not require changes to the HDaudio
legacy.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwY7KsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MFqB/4m9nlfUeXTpiSD1FgVIlMmdPNUg4V2
6Ybztaw4kRc5LuQN8PXQmaFLx020yAnLvI7Zzj7l3K8r6a9lfyFs+pKL0wtBnNK2
9QEFmOVQ3QFpt31Yb2IQeO4dfNbiyKeczjLau4mXWTl0j5dc/UH+HasE1dRZOxsC
rqJ8IsdibIVxVtQ7ZmcnU+y6XK0inBHAAh6ksMehsufShGrfrLs/nRBaXRZcRqJg
ciSFY5uYRYkDxTgogTpNRfVy4nr17N10+0sgrQ3RtaaqgG3gBXsHca1meyxKYW3Q
TssOJGIl3+uGiAMNyZqzxe5pAwwuGhZ3hAAAODtfYJQtAuAOW3/45Wqh
=phWF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.21
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
The current SKYLAKE kconfig is a all-you-can-eat selection that will
support all known plaforms. This is however not necessarily a good
thing: most platforms for SKL and KBL don't support the DSP, but a
number of CNL/WHL ones do. Selecting this driver in all cases isn't
really smart and will require users to muck with blacklists.
Partition the configs to allow distributions to select on which
platform this driver is used. Keep the existing SND_SOC_INTEL_SKYLAKE
config to select everything for backwards compatibility. This patch does
not provide new functionality, only finer-grained choices in supported
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add error logs to make probe debug easier.
Also remove hard-coded dependency on NHLT. NHLT literally stands for
NonHdaudioLinkTable and is only required for SSP/DMIC interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
bus->ppcap is now tested upfront, there is no need to re-check if the
hardware is exposed as needed. Remove tests and remove indentation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check immediately if required HDaudio capabilities can't be found (no
PPCAP or no streams exposed in GCAP), and move all DMA inits after the
error tests.
PPCAP and GCAP are not reliable indicators of DSP presence, but if
they don't exist then the driver will not work.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing PPCAP and GCAP fields cannot be used reliably to
determine if the DSP is enabled by the BIOS. Instead rely on the
class/subclass information to find out if this driver can run or
not. The values in the code don't seem to be documented in publicly
available documents but are part of recommendations made to BIOS
writers and have been verified to be accurate on a number of
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's with CNP, supposed to be equivalent with CNL entry.
Keep the existing declaration style for now, at a later point we may
transition and use PCI_DEVICE_DATA().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new Dell IoT platform uses kabylake + alc3277 codec, and alc3277
shares the driver with the codec rt5660, here we generate a new
machine driver based on kbl_da7219_max98357a.
The audio design on this IoT platform is as below:
- Intel kabylake platform
- connect the codec ALC3277 via SSP0
- line-out and line-in with Micbias jacks
- line-out mute control and jack detection of line-out and line-in
- two HDMI ports with audio capability
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the recent refactoring, snd_hdac_display_power() doesn't return
any error, hence it can be defined to return void.
This makes many error checks redundant and allows us to reduce them
gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HD-audio code manages the DRM audio power via too complex
redirections, and this seems even still unbalanced in a corner case as
Intel DRM CI has been intermittently reporting. This patch is a big
surgery for addressing the complexity and the possible unbalance.
Basically the patch changes the display PM in the following ways:
- Both HD-audio controller and codec drivers call a single helper,
snd_hdac_display_power(). (Formerly, the display power control from
a codec was done indirectly via link_power bus ops.)
- snd_hdac_display_power() receives the codec address index. For
turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER.
- snd_hdac_display_power() doesn't manage refcounts any longer, but
keeps the power status in bitmap. If any of controller or codecs is
turned on, the function updates the DRM power state via get_power()
or put_power().
Also this refactor allows us more cleanup:
- The link_power bus ops is dropped, so there is no longer indirect
management, as mentioned in the above.
- hdac_device link_power_control flag is moved to hda_codec
display_power_control flag, as it's only for HDA legacy.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From the da7219 spec, the button A, B, C and D are remapped to
0, 1, 2 and 3 respectively where button A is KEY_PLAYPAUSE,
B is KEY_VOLUMEUP, C is KEY_VOLUMEDOWN and D is KEY_VOICECOMMAND.
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Signed-off-by: Max Chang <changmax@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Point of View Mobii TAB-P1005W-232 v2.0 tablet, this
BYTCR device uses IN1 for its MIC and JD2 for jack-detect, rather then the
default IN3 and JD1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Prowise PT301 tablet, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
Also it uses IN1 for its MIC and JD2 for jack-detect, rather then the
default IN3 and JD1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Gnawty model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Clapper and Swanky models.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Gnawty that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201787
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Jaime Pérez <19.jaime.91@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Clapper model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Swanky model.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Clapper that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Entry needed for ICL RVP w/ RT274
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If mclk/sclk is already running, FW responds with IPC reply MCLK/SCLK
already running. Add these to the IPC reply lookup table.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Guenter Roeck