Resources were not freed properly in some cases.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework cmd and acx interfaces, it was just too confusing earlier. Now
all commands need to contain all the needed headers, either just cmd
headers or both cmd and acx headers. This accomplish to remove the
extra copy done for each command. The interfaces are now properly
documented as well.
Also try to make all commands safe for DMA transfers. I might have missed
some, but most of them should be fixed now.
And this is not all! As a free bonus you will also get some cosmetic
cleanups and code reorganisation. Order today!
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the sanity check on beacon interval
which was done only for mesh mode to all operating
modes just to be safe.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power save support depends on the firmware capabilities rather than the
card's hardware interface. Use the FW_CAPINFO_PS bit in the firmware
capabilities mask throughout the driver in place of the redundant
ps_supported flag and don't make decisions about PS support in the
interface drivers (with the exception of a special case in the USB
driver).
V2: put the USB special case in the right place.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cardbus and some PCI cards use hardware LEDs rather than software GPIOs.
Program them with the proper blink patterns when idle, scanning or
associated. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13288.
Tested-by: Frans Pop <elendil@planet.nl>
Tested-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah_gpios array isn't used, and ah_current_channel can be a pointer
instead of an embedded struct. Removing these and some other
write-only variables, and moving some things around for better
packing and cache utilization saves 116 bytes.
text data bss dec hex filename
121762 472 64 122298 1ddba ath5k_before.ko
121646 472 64 122182 1dd46 ath5k.ko
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can easily run out of tx buf if there is any stuck in
transmission, so downgrade it to WARN_ON().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already has one to keep track of number of failure
addba attempts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_TX_CTL_AMPDU in tx control flags should be enough
to confirm BA is negotiated for that tid.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c3a8c5b6 ("cxgb3: move away from LLTX") exposed a bug in how
cxgb3 looks up the netdev_queue it stashes away in a qset during
initialization. For multiport devices, the TX queue index it uses is
offset by the first_qset index of each port. This leads to a crash
once LLTX is removed, since hard_start_xmit is called with one TX
queue lock held, while the TX reclaim timer task grabs a different
(wrong) TX queue lock when it frees skbs.
Fix this by removing the first_qset offset used to look up the TX
queue passed into t3_sge_alloc_qset() from setup_sge_qsets().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the mainline kernel, p54usb will fail because the TX queue length can
become < 0. This problem has been reported as Bugzilla #13725. The failure
is expressed by the following message in the logs:
WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]()
Hardware name: HP Pavilion dv2700 Notebook PC
tx refused but queue active
This problem has been recently observed in the wireless-testing tree, where
a full solution is being tested. That fix is too invasive for 2.6.31-rcX,
but the simple change supplied here will prevent the failure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.
This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a race condition -- started can be set to true
before channel is set due to the way mac80211 callbacks
currently work (->start should probably pass the channel
we would like to have initially). For now simply add a
check to hwsim to avoid dereferencing the NULL channel
pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for the Broadcom 4318E chipset on PCMCIA/CF cards. The
4318E can do 802.11A/B/G, only B and G mode are supported in b43.
Signed-off-by: Clyde McPherson <ccmcphe@verizon.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:
Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Yevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"
It appears that this simple patch makes the device work perfectly.
This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drain the MAC TX fifos when a port goes down.
Back pressure might otherwise occur, leading to both
ports of the same adapter to hang.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Override the mac index computation for the gen2 adapter,
as each port is expected to use index 0.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the HW SMT table initialization to avoid random
mss miscomputations for offload connections.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use request_firmware() to load the phy's EDC programmation
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't always see the link status update interrupt
when we come out of reset and the peer is up.
Check and report the link status right before enabling interrupts.
Also fix LED settings, to get a consistent link status.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max packet size is not the only field in T3C's High Water Mark register.
Mask the register to access this field.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 phys are were not getting the Global Tx disable bit set
when powered down, leading to an inconsistent link state
on peer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing SUPPORTED_TP flag.
Update FW version checking.
Do the full initialization even if the FW version is unknown,
it might help catching further issues.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the r6040 device IRQ line is shared we will enter the driver
interrupt service routine, mask off the device interrupt enable
register (MIER) and return with IRQ_NONE, we would then leave the
device with interrupts disabled, this patch fixes that issue.
Reported-by: Steve Holland <sdh4@iastate.edu>
Signed-off-by: Joe Chou <joe.chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that network interface is running before changing its MAC address.
Otherwise, rxch is accessed when it's NULL - causing a kernel oops.
Moreover, check that the new MAC address is valid.
Signed-off-by: Pablo Bitton <pablo.bitton@gmail.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Chaithrika U S <chaithrika@ti.com>
[tested on DM6467 EVM]
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was defaulting to using the lock for pci-e function 0 for
all of the phys due to the fact that the lan id was not being set prior to
initialization. This change makes it so that the function id is set prior
to checking for the phy id.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can reclaim transmitted skbs to use in the receive path, so-called
skb recycling support.
Also reorder ucc_geth_poll() steps, so that we'll clean tx ring firstly,
thus maybe reclaim some skbs for rx.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the third (I think) polarity error I accidentally
introduced in the rfkill rewrite to make wireless work
again on (certain?) HP laptops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're missing a Kconfig help for the iwmc3200wifi driver.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we reclaim the tx desc, we always assume that the
last desc is a holding desc, which is not true, and skip it.
If the tx queue is drained during channel change, internal
reset and etc, the last descriptor may not be the holding
descriptor and we fail to reclaim them. This results in the
following two issues.
1. Tx stuck - We drop all the frames coming from upper layer
due to shortage in tx desc.
2. Crash - If we fail to reclaim a tx descriptor, we miss to
update the tx BA window with the seq number of the frame
associated to that desc, which, at some point, result in
the following crash due to an assert failure in ath_tx_addto_baw().
This patch fixes these two issues.
kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180!
[155064.304164] invalid opcode: 0000 [#1] SMP
Call Trace:
[<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k]
[<fbbc9591>] ipv6? __ieee80211_tx+0x41/0x120 [mac80211]
[<fbbcb5ae>] ? aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211]
[<c037e501>] aes_generic? _spin_lock_irqsave+0x31/0x40
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<fbbcda5a>] ? af_packetieee80211_select_queue+0xa/0x100 [mac80211]
[<c02f53b7>] ? i915dev_queue_xmit+0x2e7/0x3f0
[<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211]
[<c031bc35>] ? ip_output+0x55/0xb0
[<c02e0188>] ? show_memcpy_count+0x18/0x60
[<c02eb186>] ? __kfree_skb+0x36/0x90
[<c02f2202>] ? binfmt_miscdev_queue_xmit_nit+0xd2/0x110
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<c033bca7>] ? scoarp_create+0x57/0x2a0
[<c02f53b7>] ? bridgedev_queue_xmit+0x2e7/0x3f0
[<c03034a0>] ? eth_header+0x0/0xc0
[<c033b95f>] stp? arp_xmit+0x5f/0x70
[<c033bf4f>] ? arp_send+0x5f/0x70
[<c033c8f5>] bnep? arp_solicit+0x105/0x210
[<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390
[<c013bf88>] ? run_timer_softirq+0x138/0x210
[<c02fa410>] ? ppdevneigh_timer_handler+0x0/0x390
[<c02fa410>] ? neigh_timer_handler+0x0/0x390
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix condition in which radio LED did not initialize correctly, and remove
4 compilation warnings.
After the recent changes in rfkill, the radio LED used by b43/b43legacy
did not always initialize correctly.
Both b43 and b43legacy used the deprecated variable radio_enabled in
struct ieee80211_conf.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The constant DMA_RX_MODE is defined to be 0x14 in the local include file
cs89x0.h. Since a constant with the same name is used elsewhere with
set_dma_mode, it seems likely that this constant could be used here.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1; identifier I; constant int C; @@
(
set_dma_mode(E1,I,...)
|
*set_dma_mode(E1,C,...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec: fix definition of 5272 version of FEC_X_DES_ACTIVE register
The ColdFire 5272 FEC driver has a different register address map
than other users of the FEC driver. And its definition of the
FEC_X_DES_ACTIVE register is incorrect, it should be 0x14.
The fec interface cannot transmit data with the old value.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
----
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checksum offload support for DM9000A and DM9000B chips.
v2 changes: added a local copy of ip_summed to save IO cycles in dm9000_send_packet
v3 changes: trans_start updating is removed.
Signed-off-by: Yeasah Pell <yeasah@comrex.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
when testing the jumbo frames with pages patch, the stats would
show rx_missed errors (dropped packets) even when connected to a
link partner with flow control enabled.
this indicates that for this MTU (9000) the flow control
thresholds are not adjusting correctly.
In fact, before this change, the FCRTH (xoff threshold) is 36864
when the fifo size is only 40000, with 9000 byte MTU.
fix it so that we at least have room for one frame after we send
the xoff.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is code extremely similar to what is committed in e1000e
already.
e1000 will no longer request 32kB slab buffers to support jumbo
frames on PCI/PCI-X adapters. This will significantly reduce the
likelyhood of order:3 allocation failures.
This new code adds support for using pages as receive buffers,
and the driver will chain multiple pages together to build a
jumbo frame for OS consumption.
The hardware takes a power of two buffer size and will
dump as much data as it can receive into 1 or more buffers.
The benefits of applying this are
1) stop akpm's dissing :-) of this lame e1000 behavior [1]
2) more efficient memory allocation (half) when using jumbo
frames, which will also allow for much better socket utilization
with jumbos since the socket is charged for the full allocation
of each receive buffer, regardless of how much is used.
3) this was a feature request by a customer
4) copybreak for small packets < 256 bytes still applies
[1] http://lkml.org/lkml/2008/7/10/68http://article.gmane.org/gmane.linux.network/130986
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows on-the-fly adjustment of the interrupts per second generated
by e1000 devices 82545/82546 (hardware support of ITR register is a
requirement)
adjust using this command:
ethtool -C eth0 rx-usecs 10
where 10 is 10 microseconds per interrupt interval, so 10 = 100,000 interrupts
per second, and 125 = 8000 interrupts per second.
changes should be immediate.
1,3 are special values and indicate the automatic tuning mode to the driver,
where 1 is 4000-90000 interrupts per second and 3 is 4000-20000 interrupts
per second and is the driver default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance driver version number after modifications.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use more efficient way to determine flag status.
2. Hardware dose not mark fragment bit against IPv6 packets,
print TCP/UDP checksum warning message for IPv4 packets
only.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware failed to update the shadow register in several cases.
It's known to be failed at 64bit box with more than 4G RAM.
In order to make the device working stable, give up using the shadow
register feature.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a large chunk of memory space preserved for
for modules, using kmalloc to obtain the needed memory.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Making coding style more consistent.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Version update
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Printing the function's configured mode of operation.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Disable fcs stripping. The minimum frame size that can be received by the
hardware is 57 Bytes. A 64 Byte Ethernet frame with the vlan tag and fcs
stripped will result in a 56 Byte frame which will lock up the receive
engine. The work around is to disable fcs stripping in the hardware which
is done with a firmware upgrade. The fixes are -
1. Ensure that the correct firmware version is used.
2. Decrement the indicated packet length of the receive packet by 4 bytes
(FCS length).
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixes in isr routine
Fixed crash with INTA mode during driver unload. Pass hldev to request_irq
instead of vdev.
Fixed Traffic failure with GRO in INTA mode. Pass the correct napi
context to gro functions.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed the code to bounds check the mss value. The hardware does bounds checking and
will not allow an oversized mss to lockup the transmit path.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixed the crash in rmmod after vpath open failed when trying to change mtu.
We should check for card status before continuing in device close.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixed memory leak by freeing memory allocated for device_config.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed ioremap of bar1 address
Driver needs only bar0 address for register access
- Removed references to bar1 and bar2 addresses
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced '0' by 'bar' in the probe function.
The 'bar' variable was already set to '0' and is already
used in pci_iomap(). This is cleaner and improves code
consistency.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
almost no users in the tree; and the few that use them treat them
like NET_RX_DROP.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet a écrit :
> Ingo Molnar a écrit :
>>> The following changes since commit 52989765629e7d182b4f146050ebba0abf2cb0b7:
>>> Linus Torvalds (1):
>>> Merge git://git.kernel.org/.../davem/net-2.6
>>>
>>> are available in the git repository at:
>>>
>>> master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git master
>> Hm, something in this lot quickly wrecked networking here - see the
>> tx timeout dump below. It starts with:
>>
>> [ 351.004596] WARNING: at net/sched/sch_generic.c:246 dev_watchdog+0x10b/0x19c()
>> [ 351.011815] Hardware name: System Product Name
>> [ 351.016220] NETDEV WATCHDOG: eth0 (forcedeth): transmit queue 0 timed out
>>
>> Config attached. Unfortunately i've got no time to do bisection
>> today.
>
>
>
> forcedeth might have a problem, in its netif_wake_queue() logic, but
> I could not see why a recent patch could make this problem visible now.
>
> CPU0/1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
> is not a new cpu either :)
>
> forcedeth uses an internal tx_stop without appropriate barrier.
>
> Could you try following patch ?
>
> (random guess as I dont have much time right now)
We might have a race in napi_schedule(), leaving interrupts disabled forever.
I cannot test this patch, I dont have the hardware...
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call resource_size(res) returns res->end - res->start + 1 and thus the
second change is semantics-preserving. res_size is then used as the second
argument of a call to request_mem_region, and the memory allocated by this
call appears to be the same as what is released in the two calls to
release_mem_region. So the size argument for those calls should be
resource_size(size) as well. Alternatively, in the second call to
release_mem_region, the second argument could be res_size, as that variable
has already been initialized at the point of this call.
The problem was found using the following semantic patch:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
@@
struct resource *res;
@@
- res->end - res->start
+ BAD(resource_size(res))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
add new id (RIOS System PC CARD3 ETHERNET).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch properly defines the maximum values for rx/tx coalescing timeouts.
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem reported by Flavio Leitner <fleitner@redhat.com>:
When setting rx/tx coalescing timeout to the values less than 12 traffic was
stopped.
The FW supports coalescing in 12us granularity, and so value of less then 12
should be interpreted as disabling coalescing
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is currently possible for an asynchronous device unregister
to cause the same tun device to be unregistered twice. This
is because the unregister in tun_chr_close only checks whether
__tun_get(tfile) != NULL. This however has nothing to do with
whether the device has already been unregistered. All it tells
you is whether __tun_detach has been called.
This patch fixes this by using the most obvious thing to test
whether the device has been unregistered.
It also moves __tun_detach outside of rtnl_unlock since nothing
that it does requires that lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 537a1bf059 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:
Badness at kernel/mutex.c:207
Pid : 1, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc1-00284-g529ba0d-dirty #2273)
PC is at __mutex_lock_slowpath+0x72/0x1bc
PR is at __mutex_lock_slowpath+0x66/0x1bc
...
matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
MIPS: Reorganize Cavium OCTEON PCI support.
Update Yoichi Yuasa's e-mail address
MIPS: Allow suspend and hibernation again on uniprocessor kernels.
MIPS: 64-bit: Fix o32 core dump
MIPS: BC47xx: Fix SSB irq setup
MIPS: CMP: Update sync-r4k for current kernel
MIPS: CMP: Move gcmp_probe to before the SMP ops
MIPS: CMP: activate CMP support
MIPS: CMP: Extend IPI handling to CPU number
MIPS: CMP: Extend the GIC IPI interrupts beyond 32
MIPS: Define __arch_swab64 for all mips r2 cpus
MIPS: Update VR41xx GPIO driver to use gpiolib
MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
MIPS: Malta: Remove unnecessary function prototypes
MIPS: MT: Remove unnecessary semicolons
MIPS: Add support for Texas Instruments AR7 System-on-a-Chip
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't merge requests of different failfast settings
cciss: Ignore stale commands after reboot
Occasionally we may see an interrupt without an event in the eq.
In intx, we currently see the event queue and return IRQ_NONE causing
a the irq to be disabled ("no one cared".) Instead, read the CEV_ISR
reg to check the existence of the interrupt.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs may require two reads of the PHY_STATUS register to determine the
link status. If the PHY is being accessed by another thread it is possible
the first read could timeout and fail. In this case, put a delay in so
the second read will pick up the correct link status.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was accessing register bits for features on parts that do
not support that feature. This could cause problems in the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently. Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing. Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround. Don't perform the
workaround if in PHY loopback mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().
I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module. So we
only check if that is the case.
This problem also shows up on Copper devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.
- mdio45_probe call was always failing due to mdio.prtad not being
set. The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0. This will allow us to set the phy_id
and phy.type correctly now.
- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.
- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some usage was only sizing a pointer rather than the data type.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set/clear the mac address register when the link goes up/down
respectively. Without this both ports of a 2-port device can end up
with the same mac address in a bonding scenario.
The new ql_link_on() and ql_link_off() will also be used in handling
certain firmware events.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addes functionality to set/clear the MAC address in the hardware
when the link goes up/down.
The MAC address register is persistent across function resets. In
bonding the same address can bounce from one port to the other. This
can cause packets to be delivered to the wrong port.
This patch clears the MAC address in the hardware when the link is down
and sets it when the link comes up.
It was found that pulling/pushing the cable from one port to another
causes the same MAC address to be in both ports.
The next patch in this series will use this functionality as well.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo