Commit c3e302edca ("net: phy: marvell10g: fix temperature sensor on 2110")
added a check for PHY ID via phydev->drv->phy_id in a function which is
called by devres at a time when phydev->drv is already set to null by
phy_remove function.
This null pointer dereference can be triggered via SFP subsystem with a
SFP module containing this Marvell PHY. When the SFP interface is put
down, the SFP subsystem removes the PHY.
Fixes: c3e302edca ("net: phy: marvell10g: fix temperature sensor on 2110")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the hardware MACTYPE hardware configuration pins are set to "XFI
with Rate Matching" the PHY interface operate at fixed 10Gbps speed. The
MAC buffer packets in both directions to match various wire speeds.
Read the MAC Type field in the Port Control register, and set the MAC
interface speed accordingly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the temperature sensor register from the correct location for the
88E2110 PHY. There is no enable/disable bit on 2110, so make
mv3310_hwmon_config() run on 88X3310 only.
Fixes: 62d0153547 ("net: phy: marvell10g: add support for the 88x2110 PHY")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
we don't need genphy_no_soft_reset() any longer. Not setting
callback soft_reset results in a no-op now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV_V2_PORT_CTRL_SWRST bit in MV_V2_PORT_CTRL is reserved on 88E2110.
Setting SWRST on 88E2110 breaks packets transfer after interface down/up
cycle.
Fixes: 8f48c2ac85 ("net: marvell10g: soft-reset the PHY when coming out of low power")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soft-reset the PHY when coming out of low power mode, which seems to
be necessary with firmware versions 0.3.3.0 and 0.3.10.0.
This depends on ("net: marvell10g: report firmware version")
Fixes: c9cc1c815d ("net: phy: marvell10g: place in powersave mode at probe")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the firmware version when probing the PHY to allow issues
attributable to firmware to be diagnosed.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify mv3310_reset() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place the 88x3310 into powersaving mode when probing, which saves 600mW
per PHY. For both PHYs on the Macchiatobin double-shot, this saves
about 10% of the board idle power.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the energy detect power down tunable, which saves
around 600mW when the link is down. The 88x3310 supports off, rx-only
and NLP every second. Enable EDPD by default for 88x3310.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling the MDI-X state of the PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the copper autonegotiation results from the copper specific
status register, rather than decoding the advertisements. Reading
what the link is actually doing will allow us to support downshift
modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need the EEPROM ID to derive the phy interface mode as we can
derive it merely from the ethtool link modes. Remove the EEPROM ID
argument to sfp_select_interface().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP+ cages to the Marvell 10G PHY driver. This is
slightly complicated by the way phylib works in that we need to use
a multi-step process to attach the SFP bus, and we also need to track
the phylink state machine to know when the module's transmit disable
signal should change state.
With appropriate DT changes, this allows the SFP+ canges on the
Macchiatobin platform to be functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_c45_aneg_done() is used by phylib as fallback for c45 PHY's if
callback aneg_done isn't defined. So we don't have to set this
explicitly. Same for genphy_c45_pma_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 88x2110 PHY support was added, the suspend and resume callbacks
were forgotten. This patch adds them to the 88x2110 PHY callback
definition.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the suspend/resume callbacks for Marvell 10G PHYs. The
three PCS (base-t, base-r and 1000base-x) are set in low power (the PCS
are powered down) when the PHY isn't used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops,
one is enough.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to the 3310, the 2110 PHY correctly reports it's 2.5G/5G
abilities. We can therefore use the genphy_c45_pma_read_abilities helper
to build the list of features.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The genphy_c45_pma_read_abilities helper now sets the Autoneg ability
in phydev->supported according to what the AN MMD reports.
We therefore don't need to manually do that in mv3310_get_features().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates
whether or not we should read register (1.21) "2.52/5G PMA Extended
Abilities", which contains information on the support of 2.5GBASET and
5GBASET.
After testing on several variants of PHYS of this family, it appears
that bit 14 in (1.11) isn't always set when it should be.
PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET,
but don't have 1.11.14 set. Their register 1.21 is filled with the
correct values, indicating 2.5G and 5G support.
PHYs 88E2110 do have their 1.11.14 bit set, as it should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.
Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.
At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.
This was tested with :
- The 88X3310, which is on the MacchiatoBin
- The 88E2010, an Alaska PHY that has no fiber interfaces, and is
limited to 5G maximum speed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch making use of helpers dedicated to linkmodes handling.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Alaska family of 10G PHYs has more abilities than the ones listed in
PHY_10GBIT_FULL_FEATURES, the exact list depending on the model.
Make use of the newly introduced .get_features call to build this list,
using genphy_c45_pma_read_abilities to build the list of supported
linkmodes, and adding autoneg ability based on what's reported by the AN
MMD.
.config_init is still used to validate the interface_mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY core expects PHY drivers not to set Pause and Asym_Pause bits,
unless the driver only wants to specify one of them due to HW
limitation. In the case of the Marvell10g driver, we don't need to set
them.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the advertisement registers content didn't change, we may have
just switched to aneg, and therefore have to trigger an aneg restart.
This matches the behavior of genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_config_aneg() in mv3310_config_aneg().
v2:
- add a comment regarding 1000BaseT vendor registers
v3:
- rebased
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: patch splitted]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 10G PHY driver has a generic way of initializing the supported
link modes by reading the PHY's C45 PMA abilities. This can be made
generic, since these registers are part of the 802.3 specifications.
This commit extracts the config_init link_mode initialization code from
marvell10g and uses it to introduce the genphy_c45_pma_read_abilities
function.
Only PMA modes are read, it's still up to the caller to set the Pause
parameters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing mv3310_modify() with phy_modify_mmd() we missed that
they behave differently, mv3310_modify() returns 1 on a changed
register value whilst phy_modify_mmd() returns 0. Fix this by replacing
phy_modify_mmd() with phy_modify_mmd_changed() where needed.
Fixes: b52c018ddc ("net: phy: make use of new MMD accessors")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let genphy_c45_read_link manage the devices to check, this removes
overhead from callers. Add C22EXT to the list of excluded devices
because it doesn't implement the status register. According to the
802.3 clause 45 spec registers 29.0 - 29.4 are reserved.
At the moment we have very few clause 45 PHY drivers, so we are
lacking experience whether other drivers will have to exclude further
devices, or may need to check PHY XS. If we should figure out that
list of devices to check needs to be configurable, I think best will
be to add a device list member to struct phy_driver.
v2:
- adjusted commit message
- exclude also device C22EXT from link checking
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.
v2:
- remove an unused variable
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.
Convert all pr_warn() calls to phydev_warn() where possible.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a thermal monitoring device for the Marvell 88x3310, which updates
once a second. We also need to hook into the suspend/resume mechanism
to ensure that the thermal monitoring is reconfigured when we resume.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in comments and error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for half-duplex 100M and 10M copper connections by parsing
the advertisment results rather than trying to decode the negotiated
speed from one of the PHYs "vendor" registers. This allows us to
decode the duplex as well, which means we can support half-duplex mode
for the slower speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún