There is no need to limit the driver use by OF/platform code.
In this case we simple remove redundant OF parts from the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no evidence of officially registered ACPI IDs for these devices.
Thus, revert ACPI support from the driver. All authors of the respective
changes are being informed here:
d5c94568cc ("iio: add bmp280 pressure and temperature driver")
6dba72eca7 ("iio: pressure: bmp280: add support for BMP180")
14beaa8f5a ("iio: pressure: bmp280: add humidity support")
Above seems a cargo cult without paying attention to how ACPI IDs
are being allocated.
Cc: Vlad Dogaru <ddvlad@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can drop some duplicate code if we use devm_action for disabling
regulators and pm and the managed variant of iio_device_register().
This allows us to completely remove all remove() callbacks from both
i2c and spi code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PM280 has an internal standby-mode, but to really save power
we should shut the sensor down and disconnect the power. With
the proper .pm hooks we can enable both runtime and system power
management of the sensor. We use the *force callbacks from the
system PM hooks. When the sensor comes back we always reconfigure
it to make sure it is ready to roll as expected.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The first version of this sensor, BMP085, supports sending an
End-of-Conversion (EOC) interrupt. Add code to support this using
a completion, in a similar vein as drivers/misc/bmp085.c does.
Make sure to check that we are given a rising edge, because the
EOC line goes from low-to-high when the conversion is ready.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This splits the BMP280 driver in three logical parts: the core driver
bmp280-core that only operated on a struct device * and a struct regmap *,
the regmap driver bmp280-regmap that can be shared between I2C and other
transports and the I2C module driver bmp280-i2c.
Cleverly bake all functionality into a single object bmp280.o so that
we still get the same module binary built for the device in the end,
without any fuzz exporting symbols to the left and right.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Andy Shevchenko