Move the irq_desc related iterators out of irq.h, into irqnr.h, also
available via interrupt.h.
This way non-genirq (and even non-hardirq) architectures get the
common definitions and iterators.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The CFI information read from AT49BV6416 lists the erase regions in the
wrong order, causing problems when trying to erase or update the first
or last 64KiB block.
Work around this by inverting the "top boot" flag, which will
effectively reverse the order of the erase regions.
This chip is obsolete, but it's used in some existing designs.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch adds support for NAND flashes connected to GPIOs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds TopBottom detection for most Macronix chips with CFI V1.0.
The main purpose of this patch is to add detection of the MX29LV400C B
used on the LaCie Ethernet Disk mini V2 NAS.
It detects the following parts correctly:-
MX28F640C3B T
MX29LV002C B
MX29LV002NC B
MX29LV004C T
MX29LV400C T/B
MX29LV800C T/B
MX29LV160C T/B
MX29SL800C T/B
MX29SL802C T/B
It detects the following uniform part as bottom but it should work
correctly:-
MX29LV040C
For T parts it causes the erase block table to be reversed correctly.
For other parts it avoids the bogus "Assuming top" message.
It does not detect the following correctly:-
MX28F640C3B B
MX29LV002C T
MX29LV002NC T
MX29LV004C B
MX29SL400C T/B
MX29SL402C T/B
If desired I could supply a more complicated patch to handle these as
well.
Only the MX29LV400C B has been physically tested; others were checked
against their data sheets.
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After choosing new c->nextblock, don't leave the wbuf offset field
occasionally pointing at the start of the next physical eraseblock.
This was causing a BUG() on NOR-ECC (Sibley) flash, where we start
writing after the cleanmarker.
Among other this fix should cover write buffer offset adjustment
after flushing the last page of an eraseblock.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the driver erase a block when it doesn't find any
existing saved log messages which is safer than assuming the
flash was already erased.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a magic number to logged kernel oops messages so that they
can be more accurately detected rather than just having to rely
on the sequence number. This also allows easier detection of
saved crashes by userspace.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix an off by one error in the mtdoops driver
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix alsa kernel-doc warning in linux-next:
Warning(linux-next-20081016//sound/core/pcm_misc.c:327): No description found for parameter 'samples'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (94 commits)
USB: remove err() macro from more usb drivers
USB: remove err() macro from usb misc drivers
USB: remove err() macro from usb core code
USB: remove err() macro from usb class drivers
USB: remove use of err() in drivers/usb/serial
USB: remove info() macro from usb mtd drivers
USB: remove info() macro from usb input drivers
USB: remove info() macro from usb network drivers
USB: remove info() macro from remaining usb drivers
USB: remove info() macro from usb/misc drivers
USB: remove info() macro from usb/serial drivers
USB: remove warn macro from HID core
USB: remove warn() macro from usb drivers
USB: remove warn() macro from usb net drivers
USB: remove warn() macro from usb media drivers
USB: remove warn() macro from usb input drivers
usb/fsl_qe_udc: clear data toggle on clear halt request
usb/fsl_qe_udc: fix response to get status request
fsl_usb2_udc: Fix oops on probe failure.
fsl_usb2_udc: Add a wmb before priming endpoint.
...
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (44 commits)
drm/i915: fix ioremap of a user address for non-root (CVE-2008-3831)
drm: make CONFIG_DRM depend on CONFIG_SHMEM.
radeon: fix PCI bus mastering support enables.
radeon: add RS400 family support.
drm/radeon: add support for RS740 IGP chipsets.
i915: GM45 has GM965-style MCH setup.
i915: Don't run retire work handler while suspended
i915: Map status page cached for chips with GTT-based HWS location.
i915: Fix up ring initialization to cover G45 oddities
i915: Use non-reserved status page index for breadcrumb
drm: Increment dev_priv->irq_received so i915_gem_interrupts count works.
drm: kill drm_device->irq
drm: wbinvd is cache coherent.
i915: add missing return in error path.
i915: fixup permissions on gem ioctls.
drm: Clean up many sparse warnings in i915.
drm: Use ioremap_wc in i915_driver instead of ioremap, since we always want WC.
drm: G33-class hardware has a newer 965-style MCH (no DCC register).
drm: Avoid oops in GEM execbuffers with bad arguments.
DRM: Return -EBADF on bad object in flink, and return curent name if it exists.
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (95 commits)
V4L/DVB (9296): Patch to remove warning message during cx88-dvb compilation
V4L/DVB (9294): gspca: Add a stop sequence in t613.
V4L/DVB (9293): gspca: Separate and fix the sensor dependant sequences in t613.
V4L/DVB (9292): gspca: Call the control setting functions at init time in t613.
V4L/DVB (9291): gspca: Do not set the white balance temperature by default in t613.
V4L/DVB (9290): gspca: Adjust the sensor init sequences in t613.
V4L/DVB (9289): gspca: Other sensor identified as om6802 in t613.
V4L/DVB (9288): gspca: Write to the USB device and not USB interface in t613.
V4L/DVB (9287): gspca: Change the name of the multi bytes write function in t613.
V4L/DVB (9286): gspca: Compilation problem of gspca.c and the kernel version.
V4L/DVB (9283): Correct typo and enable setting the gain on the mt9m111 sensor
V4L/DVB (9282): Properly iterate the urbs when destroying them.
V4L/DVB (9281): gspca: Add hflip and vflip to the po1030 sensor
V4L/DVB (9280): gspca: Use the gspca debug macros
V4L/DVB (9279): gspca: Correct some copyright headers
V4L/DVB (9278): gspca: Remove the m5602_debug variable
V4L/DVB (9277): gspca: propagate an error in m5602_start_transfer()
V4L/DVB (9276): videobuf-dvb: two functions are now static
V4L/DVB (9275): dvb: input data pointer of cx24116_writeregN() should be const
V4L/DVB (9274): Remove spurious messages and turn into debug.
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Remove automatic enabling of the HUGE_FILE feature flag
ext4: Replace hackish ext4_mb_poll_new_transaction with commit callback
ext4: Update Documentation/filesystems/ext4.txt
ext4: Remove unused mount options: nomballoc, mballoc, nocheck
ext4: Remove compile warnings when building w/o CONFIG_PROC_FS
ext4: Add missing newlines to printk messages
ext4: Fix file fragmentation during large file write.
vfs: Add no_nrwrite_index_update writeback control flag
vfs: Remove the range_cont writeback mode.
ext4: Use tag dirty lookup during mpage_da_submit_io
ext4: let the block device know when unused blocks can be discarded
ext4: Don't reuse released data blocks until transaction commits
ext4: Use an rbtree for tracking blocks freed during transaction.
ext4: Do mballoc init before doing filesystem recovery
ext4: Free ext4_prealloc_space using kmem_cache_free
ext4: Fix Kconfig typo for ext4dev
ext4: Remove an old reference to ext4dev in Makefile comment
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible. In the
few places that will not work out, use a basic printk().
Clean up the remaining usages of this in the drivers/usb/ directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were two stragglers that got missed in the last merge of the HID tree that forgot to change the warn() calls to dev_warn(). This patch fixes them up.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code didn't respond correctly to get status request on
device and endpoint. Although normal operations can work without the
fix. It is not compliant with USB spec chapter9 and fails USBCV ch9
tests. The patch fix this and a few style/typo problems.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some circumstances when fsl_udc_probe fails udc_controller is freed but
the pointer remains non-NULL. fsl_udc_remove will then try and teardown
the partly initialized and freed controller structure resulting in an oops.
This patch ensures udc_controller is either NULL or fully initialized after
fsl_udc_probe.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wmb to fsl_queue_td before priming the endpoint. This ensures that the
modifications to the QH are seen by the hardware.
Added comment as suggested by Felipe Balbi.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fsl_queue_td always returns 0. Make it void and remove checks for non-zero
return in callers.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uninline udc_reset_ep_queue and remove it's unused return value.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename the arguments of the fsl_writel macro to match their use.
Remove a couple of unnecessary prototypes.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move spinlock initialization earlier so we can turn shared irq handler
debugging on safely.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Missing spaces were causing the /proc debugging output to be rather
unreadable.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
VDBG always outputs a trailing \n.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some sparse "integer used as NULL pointer" warnings.
Remove some unnecessary volatiles and static initialization.
Remove some unused struct members and reorder to improve packing.
Remove a few unneeded includes.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove check for udc == NULL in dr_controller_setup. All callers of
this function have already dereferenced udc at some point.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make dr_ep_setup function static as it's never used outside this file.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add range check on buffer sizes passed in from user space
(max is 8*PAGE_SIZE) which will work for the most common
spectrometers even at pages as small as 1K.
Add kref to vst device structure to preserve reference to the
usb object until we truly are done with it.
From: Stephen Ware <stephen.ware@eqware.net>
From: Dennis O'Brien <dennis.obrien@eqware.net>
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1149) fixes an obscure problem in OHCI polling. In the
current code, if the RHSC interrupt status flag turns on at a time
when RHSC interrupts are disabled, it will remain on forever:
The interrupt handler is the only place where RHSC status
gets turned back off;
The interrupt handler won't turn RHSC status off because it
doesn't turn off status flags if the corresponding interrupt
isn't enabled;
RHSC interrupts will never get enabled because
ohci_root_hub_state_changes() doesn't reenable RHSC if RHSC
status is on!
As a result we will continue polling indefinitely instead of reverting
to interrupt-driven operation, and the root hub will not autosuspend.
This particular sequence of events is not at all unusual; in fact
plugging a USB device into an OHCI controller will usually cause it to
occur.
Of course, this is a bug. The proper thing to do is to turn off RHSC
status just before reading the actual port status values. That way
either a port status change will be detected (if it occurs before the
status read) or it will turn RHSC back on. Possibly both, but that
won't hurt anything.
We can still check for systems in which RHSC is totally broken, by
re-reading RHSC after clearing it and before reading the port
statuses. (This re-read has to be done anyway, to post the earlier
write.) If RHSC is on but no port-change statuses are set, then we
know that RHSC is broken and we can avoid re-enabling it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Hunter