The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus. This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.
The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.
The ehci and ohci blocks share a common clocking and PHY
infrastructure. Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.
Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit
function. This was affecting rmmod command not to work for OMAP3
platforms. The platform driver un-registration for OMAP3 platforms is
perfomed while removing the OHCI module from kernel.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags. This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.
The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.
(Strictly speaking, the authorized_default flag should become atomic
as well. I didn't bother with it because it gets changed only via
sysfs. It can be done later, if anyone wants.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On OMAP systems, we have two different OHCI controllers. The legacy
one is present in OMAP1/2 chips, and the newer one comes bundled as
a companion to the EHCI controller on OMAP3 and newer chips.
We may have multi-omap configurations where OMAP2 and OMAP3
support may be enabled in the same kernel, and need a mechanism
to keep both drivers around.
This patch adds a Kconfig entry for each of these drivers.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Texas Instruments DA8xx/OMAP-L1x OHCI glue layer.
This OHCI implementation is not without quirks: there's only one physical port
despite the root hub reporting two; the port's power control and over-current
status bits are not connected to any pins, however, at least on the DA830 EVM
board, those signals are connected via GPIO, thus the provision was made for
overriding the OHCI port power and over-current bits at the board level...
Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix sparse warnings in drivers/usb/host/ohci-hcd.c.
Four of the following sparse warning are seen when building on
ARM due do the macro raw_local_irq_save():
warning: symbol 'temp' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (97 commits)
USB: qcserial: add device id for HP devices
USB: isp1760: Add a delay before reading the SKIPMAP registers in isp1760-hcd.c
USB: allow malformed LANGID descriptors
USB: pxa27x_udc: typo fixes and code cleanups
USB: gadget: gadget zero uses new suspend/resume hooks
USB: gadget: composite device-level suspend/resume hooks
USB: r8a66597-hcd: suspend/resume support
USB: more u32 conversion after transfer_buffer_length and actual_length
USB: Fix cp2101 USB serial device driver termios functions for console use
USB: CP2101 New Device ID
USB: ipaq: handle 4 endpoint devices
USB: S3C: Move usb-control.h to platform include
USB: ohci-hcd: Add ARCH_S3C24XX to the ohci-s3c2410.c glue
USB: pedantic: spelling correction in comment for ch9.h
USB: host: fix sparse warning: Using plain integer as NULL pointer
USB: ohci-s3c2410: fix name of bus clock
USB: ohci-s3c2410: remove <mach/hardware.h> include
USB: serial: rename cp2101 driver to cp210x
USB: CP2101 Reduce Error Logging
USB: CP2101 Support AN205 baud rates
...
The ohci-s3c2410.c glue supports both CONFIG_ARCH_S3C2410 and
CONFIG_ARCH_S3C64XX so add it to the build of ohci-s3c2410.c
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1193b) enables wakeup during initialization for all PCI
host controllers, and it removes some code (and comments!) that are no
longer needed now that the PCI core automatically initializes wakeup
settings for all new devices.
The idea is that the bus should initialize wakeup, and the bus glue
or controller driver should enable it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Toshiba Mobile I/O chips have OHCI controller built in.
E.g. the tc6393xb chip found in several Toshiba e-Series PDAs
and in Sharp Zaurus SL-6000 PDA. This adds platform glue
to support OHCI function of the chip.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1139) adds a warning to the system log whenever ehci-hcd
is loaded after ohci-hcd or uhci-hcd. Nowadays most distributions are
pretty good about not doing this; maybe the warning will help convince
anyone still doing it wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.27]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1145) removes the essentially useless driver-version
strings from ehci-hcd, ohci-hcd, and uhci-hcd. It also unifies the
form of the banner lines they display upon loading and adds a missing
test for usb_disabled() to ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As RMK pointed out, considering the fact that the _only_ platform with
a PXA and SA1111 is the Lubbock, and that SA1111 DMA doesn't work there,
(i.e. the SA1111 OHCI doesn't work there) the SA1111 OHCI driver should
really be made SA11x0 specific.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ). The timer would then fire at time (0 <= T <
HZ).
Fix them to use round_jiffies(jiffies + HZ);
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: ohci-sm501 driver V2
This patch adds sm501 ohci support. It's all very straightforward with the
exception of dma_declare_coherent_memory() and HCD_LOCAL_MEM. Together they
are used to ensure that usb data is allocated using dma_alloc_coherent(),
and that only valid dma memory is used to allocate from. This driver is
a platform device, and the mfd driver sm501.c is already creating one
usb host controller instance per sm501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OHCI driver's IRQ handler, while processing a WDH interrupt, masks
and unmasks it. I believe this is both broken (the write may still be
posted during the donelist processing it's trying to safeguard) and
useless as this IRQ may not be reissued until it's acked (unless this
legacy code is an uncommented workaround for some chip erratum).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.
This mechanism can't be used on some controllers. Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.
This patch removes the optimisation and makes the code clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove various newly-introduced compiler warnings for OHCI.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds SSB bus glue for the USB OHCI HCD.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as975) reorganizes the way ohci-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as954) implements a suggestion of David Brownell's. Now
the host controller drivers are responsible for linking and unlinking
URBs to/from their endpoint queues. This eliminates the possiblity of
strange situations where usbcore thinks an URB is linked but the HCD
thinks it isn't. It also means HCDs no longer have to check for URBs
being dequeued before they were fully enqueued.
In addition to the core changes, this requires changing every host
controller driver and the root-hub URB handler. For the most part the
required changes are fairly small; drivers have to call
usb_hcd_link_urb_to_ep() in their urb_enqueue method,
usb_hcd_check_unlink_urb() in their urb_dequeue method, and
usb_hcd_unlink_urb_from_ep() before giving URBs back. A few HCDs make
matters more complicated by the way they split up the flow of control.
In addition some method interfaces get changed. The endpoint argument
for urb_enqueue is now redundant so it is removed. The unlink status
is required by usb_hcd_check_unlink_urb(), so it has been added to
urb_dequeue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZF Micro OHCI controller exhibits unexpected behavior that seems to be
related to high load. Under certain conditions, the controller will
complete a TD, remove it from the endpoint's queue, and fail to add it to
the donelist. This causes the endpoint to appear to stop responding. Worse,
if the device is removed while in that state, OHCI will hang while waiting
for the orphaned TD to complete. The situation is not recoverable without
rebooting.
This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag:
1. A watchdog routine periodically scans the OHCI structures to check
for orphaned TDs. In these cases the TD is taken back from the
controller and completed normally.
2. If a device is removed while the endpoint is hung but before the
watchdog catches the situation, any outstanding TDs are taken back
from the controller in the 'sanitize' phase.
The ohci-hcd driver used to print "INTR_SF lossage" in this situation;
this changes it to the universally accurate "ED unlink timeout". Other
instances of this message presumably have different root causes.
Both this Compaq quirk and a NEC quirk are now properly compiled out for
non-PCI builds of this driver.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB HCD glue updates to reflect the new PS3 unifed device support.
- Fixed remove() routine.
- Added shutdown() routine.
- Added request_mem_region() call.
- Fixed MODULE_ALIAS().
- Made a proper fix for the hack done to support muti-platform in commit
48fda45120.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears
at random times and is very, very difficult to reproduce. Without the
following patch, Linux would shut the chip and its associated devices
down. In Apple PowerBooks this leads to an unusable keyboard and mouse
(SSH still working). The idea of restarting the chip is taken from
public Darwin code.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend. In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.
This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume. (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Duplicate what Zach Brown did for pr_debug in commit
8b2a1fd1b3
[akpm@linux-foundation.org: fix a couple of things which broke]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ps3_system_bus_driver_register is PS3 platform specific function.
On other platforms, it triggers WARN_ON in kref_get.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB OHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restructure the ohci_hcd_mod_init error handling code in to better support
the multiple platform drivers. This does not change the functionality.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PPC embedded systems can have a ohci controller builtin. In the
new model, it will end up as a driver on the of_platform bus,
this patches takes care of them.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Daney