Taken from:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
(based on function RT33xx_ChipSwitchChannel)
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Synchronize code with Ralink driver:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
Based on functions:
RT30xx_ChipSwitchChannel
RT33xx_ChipSwitchChannel
NICInitRT3370RFRegisters
and defines from:
include/chip/rt33xx.h
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Synchronize code with Ralink driver:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
Based on functions:
RT33xx_ChipSwitchChannel
RT30xx_ChipSwitchChannel
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Synchronize code with Ralink driver:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
Based on functions:
RT33xx_ChipSwitchChannel
RT30xx_ChipSwitchChannel
RT33xx_Init
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Synchronize code with Ralink driver:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
(functions: RT33xx_ChipSwitchChannel() and RT30xx_ChipSwitchChannel())
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch correct the type of variables containing the rssi
values read from the rxwi.
In function rt2800_agc_to_rssi() 3 variables (rssi0, rssi1, rss2)
defined as int was assigned a 16bit signed values as unsigned.
From a test with a hi-gain antenna I verified that the rxwi
contains signed rssi values in the range -13/+81 (inclusive)
with 0 as an error condition. In case of negative values a
condition is triggered and the function return -128dBm while
the signal is at its maximum. This patch correct the cast so
negative values are not treated as very high positive values
(ex. -13 does not become 243).
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to be only needed as workaround for hardware problem on
PCI devices.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Same devices can generate interrupt without properly setting bit in
INT_SOURCE_CSR register (spurious interrupt), what will cause IRQ line
will be disabled by interrupts controller driver.
We discovered that clearing INT_MASK_CSR stops such behaviour. We
previously first read that register, and then clear all know interrupt
sources bits and do not touch reserved bits. After this patch, we write
to all register content (I believe writing to reserved bits on that
register will not cause any problems, I tested that on my rt2800pci
device).
This fix very bad performance problem, practically making device
unusable (since worked without interrupts), reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=658451
We previously tried to workaround that issue in commit
4ba7d99978 "rt2800pci: handle spurious
interrupts", but it was reverted in commit
82e5fc2a34
as thing, that will prevent to detect real spurious interrupts.
Reported-and-tested-by: Amir Hedayaty <hedayaty@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the latest Ralink vendor drivers, this seems to be the real
RF chipset type.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When USB driver requires padding at the end of frame or URB it will report
this need by increasing return value of get_tx_data_len callback. Common
USB code uses that return value as desired URB length.
Ensure that appropriate part of skb's tailroom exists and is zeroed.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
--
drivers/net/wireless/rt2x00/rt2x00usb.c | 16 +++++++++++++---
1 files changed, 13 insertions(+), 3 deletions(-)
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older USB drivers does not append end padding to skb but instead report
it in size of data to be transmitted to HW. rt2800usb should follow that
behaviour. Custom write_tx_data callback which was adding pad to skb
is not be needed any more.
Thanks to this patch frames handed back from rt2800usb to mac80211 will
no longer contain end padding.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing on the openSUSE wireless forum has shown that a Linksys
WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is
written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a cosmetical fix since we only return survey data for the
active channel but it allows iw to show that the survey data is
for the currently used channel.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just another USB identifier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ieee80211_free_txskb should be used when dropping a frame in the device
rx path such that mac80211 knows about this frame being dropped.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously BlockAcks were always dropped by the rt2800 hardware while
BlockAckReqs were always accepted. However, both are only useful on
monitor interfaces at the moment and both are control frames. So
pass them up when mac80211 sets FIF_CONTROL.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 4ba7d99978.
The original patch was a misguided attempt to improve performance on
some hardware that is apparently prone to spurious interrupt generation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 23085d5796.
The original patch was a misguided attempt to improve performance on
some hardware that is apparently prone to spurious interrupt generation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts the drivers in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Yoann DI-RUZZA <y.diruzza@lim.eu>
Cc: George <george0505@realtek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix __le32 to __le16 conversion of the first word of an 8-word block
of EEPROM read via the efuse method.
Reported-and-tested-by: Ingvar Hagelund <ingvar@redpill-linpro.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
CC: <stable@vger.kernel.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have documented case of very bad performance issue on rt2800pci
device, because it generate spurious interrupt, what cause irq line
is disabled: https://bugzilla.redhat.com/show_bug.cgi?id=658451
We already address that problem in separate patch by returning
IRQ_HANDLED from interrupt handler. We think similar fix is needed for
other rt2x00 PCI devices, because users report performance problems on
these devices too.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic powersaving code that determines after reception of a frame
whether the device should go back to sleep or whether is could stay
awake was calling rt2x00lib_config directly from RX tasklet context.
On a number of the devices this call can actually sleep, due to having
to confirm that the sleeping commands have been executed successfully.
Fix this by moving the call to rt2x00lib_config to a workqueue call.
This fixes bug https://bugzilla.redhat.com/show_bug.cgi?id=731672
Tested-by: Tomas Trnka <tomastrnka@gmx.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is reported to be an RT3070 based device.
Reported-by: Teika Kazura <teika@lavabit.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The eeprom data is stored in little-endian order in the rt2x00 library.
As it was converted to cpu order in the read routines, the data need to
be converted to LE on a big-endian platform.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated
if statement results in incorrect flow, whereas the equivalent switch
statement works correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use rt2800_config_wcid and rt2800_delete_wcid_attr to initialize the
WCID table instead of writing to the registers directly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a STA is not known by the hw (i.e. has no WCID assigned) don't allow
aggregation since this might mess up tx status reports and we won't be
able to distinguish the reports of multiple WCID-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to assign a WCID to each STA even for STAs without
crypto key.
To achieve this search for an unused WCID in the HW WCID table and
assign it to the according STA. When configuring a pairwise key for this
STA we don't need to write the MAC address and BSSIDX anymore but just
update the crypto related fields in the WCID_ATTR table.
This has two advantages:
1) Setting a new key for an already available STA (PTK rekeying) is
slightly less expensive and should improve performance in situations
where a lot of rekeying happens (e.g. a huge number of stations and/or
a small rekeying interval)
2) The TXWI now gets a WCID assigned for unencrypted frames which will
be reflected in the corresponding tx status report. This should make tx
status reports in unencrypted AP mode more reliable as we can
distinguish between multiple key-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending an unencrypted frame to a STA the driver might want to pass
a suitable WCID since we don't have a key index to allow tx status
reports to get properly assigned to the correct STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a WCID was already assigned to a STA the key configuration
functions need to use the same WCID for configuring the keys. Hence, add
the WCID to the crypo configuration structure.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements a basic sta_add and sta_remove callback. Introduce a new
structure rt2x00_sta and ask mac80211 to allocate it as private part of
its ieee80211_sta. rt2x00_sta only contains the WCID for now.
The sta_add callback allows the driver to assign a WCID to a station
that is currently being added. The same wcid is also passed to the
sta_remove callback one mac80211 removes this STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by a later patch. No functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading the TX desciptor words from coherent memory is always uncached
and potentially slow. Hence, don't read the TX descriptor prior to
writing it since we update all fields anyway.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices are not capable of configuring arbitrary LED on/off
periods. The LED_CFG register fields ON_PERIOD and OFF_PERIOD are only
used by the hw when the LED mode is set to "blink upon TX".
Hence, remove the blink callback. This will result in software emulation
for LED blinking.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can save an indirect function call + some instructions for fetching
the actual function pointer by passing the driver specific txwi pointer
directly from rt2800pci/rt2800usb to rt2800lib instead of using the
rt2800_drv_get_txwi callback.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.
BUG: unable to handle kernel paging request at 6b6b6b9f
IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30
*pdpt = 0000000034f21001 *pde = 0000000000000000
Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO
EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1
EIP is at driver_sysfs_remove+0x10/0x30
EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b
ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000)
Call Trace:
[<c06909ef>] __device_release_driver+0x1f/0xa0
[<c0690b20>] device_release_driver+0x20/0x40
[<c068fd64>] bus_remove_device+0x84/0xe0
[<c068e12a>] ? device_remove_attrs+0x2a/0x80
[<c068e267>] device_del+0xe7/0x170
[<c06d93d4>] usb_disconnect+0xd4/0x180
[<c06d9d61>] hub_thread+0x691/0x1600
[<c0473260>] ? wake_up_bit+0x30/0x30
[<c0442a39>] ? complete+0x49/0x60
[<c06d96d0>] ? hub_disconnect+0xd0/0xd0
[<c06d96d0>] ? hub_disconnect+0xd0/0xd0
[<c0472eb4>] kthread+0x74/0x80
[<c0472e40>] ? kthread_worker_fn+0x150/0x150
[<c0809b3e>] kernel_thread_helper+0x6/0x10
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800usb_work_txdone we check flags in order:
- ENTRY_OWNER_DEVICE_DATA
- ENTRY_DATA_STATUS_PENDING
- ENTRY_DATA_IO_FAILED
Modify flags in separate order in rt2x00usb_interrupt_txdone, to avoid
processing entries in _txdone with wrong flags or skip processing
ready entries.
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add a device id for the wifi usb keys shiped by DVICO with
some of their tvix hardware.
Signed-off-by: Anthony Bourguignon <contact+kernel@toniob.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Maik-Holger Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.
Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.
While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may call rt2x00queue_pause_queue(queue) with queue == NULL. Bug
was introduced by commit 62fe778412
"rt2x00: Fix stuck queue in tx failure case" .
Cc: stable@kernel.org # 3.0+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced by commit
77b5621bac (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should clear skb->data not skb itself. Bug was introduced by:
commit 0b8004aa12 "rt2x00: Properly
reserve room for descriptors in skbs".
Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b.
Chipset info: rt: 3390, rf: 000b, rev: 3213.
I have just bought one, which started to work perfectly after the ID was added through this patch.
Signed-off-by: Eduardo Bacchi Kienetz <eduardo@kienetz.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
This would exactly mimic the behaviour of the legacy vendor driver which
also doesn't go in powersave mode if there are still TX frames that are not
transmitted.
This should make powersaving and rt2x00 a better couple.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Wim Vander Schelden <wim@fixnum.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently a lot of actions that can be done without the queue's tx lock
being held are done inside the locked area.
Move them out to have a leaner and meaner code that operates while the
tx lock is being held.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions that create the tx descriptor structure do not operate on
a queue entry at all. Signal this fact in the code by not providing a
queue entry as a parameter, but the rt2x00 device structure and the skb
directly.
This patch is a preparation for reducing the time a queue is locked for
a tx operation.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00 driver gets frequent occurrences of the following error message
when operating under load:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the
non-full queue 2.
This is caused by simultaneous attempts from mac80211 to send a frame via
rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame,
causing the second frame to fail sending with the above mentioned error
message.
Fix this by introducing a per-queue spinlock to serialize the TX operations
on that queue.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When module is reloaded, device may fail to work, with messages:
[ 342.211926] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x0059, type=2.
[ 342.314254] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004a, type=2.
[ 342.416458] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 3183 max 2432.
[ 342.518605] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00c9, type=2.
[ 342.620836] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00ae, type=1.
[ 342.723201] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 342.825399] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 342.927624] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 0 max 2432.
[ 343.029804] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2491 max 2432.
[ 343.132008] phy40 -> rt2x00lib_rxdone: Warning - Wrong frame size 2576 max 2432.
[ 343.234326] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x004c, type=1.
[ 343.438723] phy40 -> rt2x00lib_rxdone_read_signal: Warning - Frame received with unrecognized signal, mode=0x0000, signal=0x00e6, type=1.
Whereas replugging device make it functional. To solve that problem
force reset device during probe.
With patch messages are gone. Unfortunately device may sometimes
still does not operate correctly after module reload (fail to receive
data after associate), but such cases are rarer than without the patch.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes rxdesc descriptor provided by hardware contains invalid
(random) data. For example rxdesc.size can be bigger than actual
size of the buffer. When this happen rt2x00crypto_rx_insert_iv()
corrupt memory doing memmove outside of buffer boundaries.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid queue and run autowakeup_work when device is not present anymore.
That prevent rmmod and device remove crash introduced by:
commit 1c0bcf89d8
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Sat Apr 30 17:18:18 2011 +0200
rt2x00: Add autowake support for USB hardware
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that support for these devices has been added we can enable them
by default and remove the Kconfig not on support for these devices to
be non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are only used by rt2800usb so they don't have to be
in rt2800lib.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lock is only used in the TX path and thus in process context. Therefore
we can use a much lighter spinlock variant.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on an earlier patch submitted by Shiang)
Add support for RT3572/RT3592/RT3592+Bluetooth combo card
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
There's no point in enabling the PA_PE bits for the bands that we are
not active on.
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txstatus_timer should only be deleted for USB devices, as it is only
initialized for USB devices.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch:
rt2x00: Make rt2x00_queue_entry_for_each more flexible
commit: 10e11568ca
introduced a severe regression on the throughput
for USB hardware. It turns out that the exiting of
the rt2x00queue_for_each_entry() was done too early.
The exact cause for this regression is unknown,
but by disabling the premature exiting of the loop
seems to resolve the issue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Reported-by: Balint Viragh <bviragh@dension.com>
Tested-by: Balint Viragh <bviragh@dension.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add necessary RF chipset define and basic support for these devices.
Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB drivers don't support automatically waking up when in powersaving mode,
add a work object which will wakeup the device in time to receive the next beacon.
Based on that beacon, we either go back into powersaving mode, or we remain awake
to receive the buffered frames for our station.
Some part of the code, especially rt2x00lib_find_ie and rt2x00lib_rxdone_check_ps
are inspired on the code from carl9170.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use flag instead of re-reading the eeprom every time.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800lib.c the rt2800_init_eeprom function the same eeprom
words were read multiple times, due to inefficient ordering of the
eeprom checks.
Reorder the checks so that each EEPROM word only has to be read once.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch
rt2x00: Optimize register access in rt2800pci
from Helmut Schaa missed one register call, namely
the rt2800_register_multiwrite which should be changed
to rt2x00pci_register_multiwrite.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add recycling functionality to rt2x00usb_register_read_async.
When the callback function returns true, resubmit the urb to
read the register again.
This optimizes the rt2800usb driver when multiple TX status reports
are pending in the register, because now we don't need to allocate
the rt2x00_async_read_data and urb structure each time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no TX status was available, the default timeout
of 20ms is a bit high. The frame is highly likely already
send out, so the TX status should be available within
only a few milliseconds.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_antenna and set_antenna callback functions, which will
allow clients to control the antenna for all non-11n hardware (Antenna handling
in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers
yet).
To best support the set_antenna callback some modifications are needed in the
diversity handling. We should never look at the default antenna settings to determine
if software diversity is enabled. Instead we should set the diversity flag when
possible, which will allow the link_tuner to automatically pick up the tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the get_ringparam callback function we can export ring parameters
to ethtool through the mac80211 interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800usb were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00usb_register_read/rt2x00usb_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00usb_register_read/write variants.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800pci were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00pci_register_read/rt2x00pci_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00pci_register_read/write variants.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.
This makes the code a bit easier readable and searchable.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code seems to be feature-complete, so no reason to not enable
these devices by default.
Also, remove the sentence about the support for these devices being
non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt33xx devices support for both PCI and USB devices has been in
the tree for a couple of months now, and seems to be functional and
not in a worse shape than the support for rt28xx and rt30xx devices.
No longer mark it as experimental and enable the support for these
devices by default.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both USB and PCI drivers allow a system administrator to dynamically add
USB/PCI IDs to the device table that a driver supports via the
/sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files.
However, for the rt2x00 drivers using this method currently crashes the
system with a NULL pointer failure.
This is due to the set-up of rt2x00 where the probe functions require a
rt2x00_ops structure in the driver_info field of the probed device. As
this field is empty for the dynamically added devices this fails for
these devices.
Fix this by introducing driver-specific probe wrappers that do nothing
but calling the bus-specific probe functions with the rt2x00_ops structure
as an argument, rather than depending on the driver_info field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the USB ID entry from the unknown devices to the list of RT35xx based
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the compiler to perform the necessary bitfield calculations
during compile time instead of run time and thus reduces the number of
instructions to run during each tasklet invocation. This should improve
performance in the RX hotpath.
This comes at the cost of a slight increase in the module size (for
example rt2800pci):
Before:
text data bss dec hex filename
14133 832 4 14969 3a79 drivers/net/wireless/rt2x00/rt2800pci.ko
After:
text data bss dec hex filename
14149 832 4 14985 3a89 drivers/net/wireless/rt2x00/rt2800pci.ko
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When powersaving is enabled, assocaition times are very high
(for WPA2 networks, the time can easily be around the 3 seconds).
This is caused, because the flushing of the queues takes
too much time. Without the flushing callback mac80211 assumes
a timeout of 100ms while scanning. Limit all flush waiting
loops to the same maximum.
We can apply this maximum by passing the drop status to the
driver, which makes sure the driver performs extra actions
during the waiting for the queue to become empty.
After these changes, association times fall within the
healthy range of ~0.6 seconds with powersaving enabled.
The difference between association time between powersaving
enabled and disabled is now only ~0.1 second (which can also
be due to the measuring method).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX status is reported by the hardware when a packet has been
sent (or after TX failed after possible retries), which is some
time after the DMA completion. Since the rt2800usb hardware can
not signal interrupts we have to use a timer, otherwise the
TX status would only be read by the next packet's TX DMA
completion, or by the watchdog thread.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog just triggers rt2800usb_work_txdone() when it
detects a TX status timeout, thus rt2800usb_work_txdone() needs to
handle this case.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps. The previous check was incorrect and caused both
false positives and false negatives.
With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to fix the "TX status report missed" warnings
by reading the TX_STA_FIFO entries as quickly as possible.
The TX_STA_FIFO is too small in hardware, thus reading
it only from the workqueue is too slow and entries get lost.
Start an asynchronous read of the TX_STA_FIFO directly from
the TX URB completion callback (atomic context, thus it cannot
use the blocking rt2800_register_read()). If the async
read returns a valid FIFO entry, it is pushed into a larger
FIFO inside struct rt2x00_dev, until rt2800_txdone() picks
it up.
A .tx_dma_done callback is added to struct rt2x00lib_ops
to trigger the async read from the URB completion callback.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.
Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.
Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.
No functional changes, just preparation for an upcoming patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.
A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.
By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.
This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 0b7fde54f9 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.
Fix this by also using rt2x00queue_pause_queue in case of tx failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices. The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC. This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request). This enables the WLAN LED for
RT305x devices.
Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already tell mac80211 to stop the queue when we hit a certain
threshold. Hence, it shouldn't happen at all that a frame gets queued
for tx on a full queue. Add an error message for this case.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
rt2x00 should send a BlockAckReq if the transmission of an AMPDU
subframe fails.
Introduce a new flag TXDONE_AMPDU to indicate that this is an AMPDU
subframe and pass IEEE80211_TX_STAT_AMPDU_NO_BACK to mac80211 if an
AMPDU subframe failed during transmission.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STBC transmissions rt2x00 used the number of RxSTBC streams the
destination STA indicates in its HT capabilities as STBC value in
the TXWI.
However, the legacy drivers and our own comment in rt2800.h suggest
that the STBC field in the TXWI only allows a value of 0 or 1.
The values 2 and 3 are reserved (probably for future devices).
And indeed, STBC transmissions to STAs indicating more then 1
RxSTBC stream fail when the STBC field is set to something >1.
Fix this by only setting the STBC field to 1 when STBC should be
used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices should adjust their tx power in accordance with the
eeproms temperature calibration values. Add a new driver callback
gain_calibration that is called every 4 seconds.
The rt2800 gain calibration routine simply runs the tx power
configuration that takes care of calculating the temperature
compensation delta.
We don't need to synchronize the calls to rt2800_config_txpower
as they should all happen from mac80211's single threaded workqueue.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit d1c3a37cee ("mac80211:
clarify alignment docs, fix up alignment") removed the requirement
for a 4-byte aligned payload rt2x00queue_align_payload is obsolete
as mac80211 will align the payload when it passes the frame to the
net stack.
As a result we can remove the call to rt2x00queue_align_payload in the
rx path and since that's the last user we can remove
rt2x00queue_align_payload altogether.
One advantage is that we save some alignment operations for frames
that don't need to be aligned (for example beause they are not passed
to the net stack).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the indention in rt2800_compesate_txpower and also fix a typo in
the function name rt2800_compesate_txpower -> rt2800_compensate_txpower.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the HT40 tx power compensation value was calculated for each
rate. However, the calculation is independent of the tx rate and as such
can be precalculated and just passed in for each rate.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the HT40 check inside the calculation function to make it easier
for a later cleanup.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can simply check if the driver registered the watchdog callback.
There's no need to have an additional flag for that.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the tx status fifo size as 512 calculate it based
on the number of tx queues and the number of entries per queue. Also
round the size up to a power of 2 as kfifo would otherwise round it
down.
On rt2800pci this will increase the kfifo size from 512 bytes to 1024
bytes which is then able to hold the tx status for all entries in all
tx queues.
Furthermore, if the number of tx queues or tx entries changes in the
future (use of the MGMT queue for example) the kfifo size doesn't need
to be updated.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of reporting an unlimited number of tx status reports to
mac80211 stop after 16 frames and reschedule the tx status tasklet.
This allows other tasklets to be run inbetween.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of receiving an unlimited number of frames, stop after 16
entries and reschedule the rxdone tasklet. This allows other tasklets
to be run inbetween.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
{rx,tx}done_work's are only initialized for usb devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add unknown Toshiba device, mentioned in rt3572sta sources, under
CONFIG_RT2800USB_UNKNOWN
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 2L Central Europe BV 8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Planex Communications, Inc. RT8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ID for Asus USB-N11 Wi-FI adapter. Tested by me.
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that all accesses to the data_queue structures is done via the specialized
rt2x00queue_get_tx_queue function or via direct accesses, there is no
need for the rt2x00queue_get_queue function anymore, so remove it.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the spirit of optimizing the code to get the queue structure of TX queues,
also optimize the code to get beacon queues. We can simply use the bcn queue
field of the rt2x00_dev structure instead of using the rt2x00queue_get_queue
function.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ATIM queue is considered to be a TX queue by the drivers that support
the queue. Therefore include support for the ATIM queue to the
rt2x00queue_get_tx_queue function so that the drivers that support the ATIM
queue can also use that function.
Add the support in such a way that drivers that do not support the ATIM
queue are not penalized in their efficiency.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current code for the atim queue is strange, as it is considered in the
rt2x00_dev structure as a second beacon queue.
Normalize this by letting the atim queue have its own struct data_queue
pointer in the rt2x00_dev structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't use interrupt threads anymore. Fix the comment.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCI device irqmask is locked by a spin_lock. Currently
spin_lock_irqsave is used everywhere. To reduce the locking overhead
replace spin_lock_irqsave in hard irq context with spin_lock and in
soft irq context with spin_lock_irq.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up multiple BSSIDs in AP mode on an rt2800pci device we
previously used the STAs AID to select an appropriate key slot. But
since the AID is per VIF we can end up with two STAs having the same AID
and thus using the same key index. This resulted in one STA overwriting
the key information of another STA.
Fix this by simply searching for the next unused entry in the pairwise
key table.
Also bring the key table init in sync with deleting keys by initializing
the key table entries to 0 instead of 1.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the code less error-prone.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_tx_rate is not valid for HT rates. Hence, restructure the
TX desciptor creation to be aware of MCS rates. The generic TX desciptor
creation now cares about the rate_mode (CCK, OFDM, MCS, GF).
As a result, ieee80211_get_tx_rate gets only called for legacy rates.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ifs" is only used by no-HT devices. Move it into the plcp substruct and
fill in the value only for no-HT devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some fields only need to be u8 and for ifs and txop we can use the
already available enums.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT and no-HT rt2x00 devices use a partly different TX descriptor.
Optimize the tx desciptor memory layout by putting the PLCP and HT
substructs into a union and introduce a new driver flag to decide which
TX desciptor format is used by the device.
This saves us the expensive PLCP calculation fOr HT devices and the HT
descriptor setup on no-HT devices.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices like rt2800* own a hardware sequence counter and thus
don't need to use a software sequence counter at all. Add a new driver
flag to shortcut the software sequence number generation on devices that
don't need it.
rt61pci, rt73usb and rt2800* seem to make use of a hw sequence counter
while rt2400pci and rt2500* need to do it in software.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue_write_tx_frame is unlikely to fail. Tell the compiler.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This special case shouldn't happen very often. Only if a frame that
is not intended to be aggregated ends up in an AMPDU _and_ was intended
to be sent at a different MCS rate as the aggregate. Hence, using
unlikely is justified.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since tx_info->control.vif was already accessed before it cant't be NULL
here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These conditions are unlikely to happen, tell the compiler.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases (tx path for example) we don't need to check for non-tx
queues in rt2x00queue_get_queue. Hence, introduce a new method
rt2x00queue_get_tx_queue that is only valid for tx queues and use it in
places where only tx queues are valid.
Furthermore, this new method is quite short and as such can be inlined
to avoid the function call overhead.
This only converts the txdone functions of drivers that don't use an ATIM
queue and the generic tx path.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800 specific code contains a lots of whitespace damage caused by
the commit 'rt2x00: Add support for RT5390 chip'.
This patch fixes those whitespace errors.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new RT5390 chip support
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Revise/Add GPIO register related definitions
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the definition of protection related registers more precisely
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit e81e0aef32 "rt2x00 : avoid
timestamp for monitor injected frame." as it breaks proper timestamp insertion
into probe responses injected by hostapd for example.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Benoit PAPILLAULT <benoit.papillault@free.fr>
Cc: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only devices that don't have RTS/CTS offload need to check for
IEEE80211_TX_RC_USE_RTS_CTS and IEEE80211_TX_RC_USE_CTS_PROTECT.
By swapping both conditions we keep the same number of needed conditionals
for devices without RTS/CTS offload but save one conditional on devices
with RTS/CTS offload.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX_PWR_CFG_* setting need to consider below cases
-compesate 20M/40M tx power delta for 2.4/5GHZ band
-limit maximum EIRP tx power to power_level of
regulatory requirement
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select
default antenna using gpio control way even if we do not turn on
antenna diversity feature.
Seperate the meaning of TX/RX chain and antenna. Some chips use
2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain
but may have 2 RX antennas to do antenna diversity.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 739fd94 ("rt2x00: Pad beacon to multiple of 32 bits")
added calls to skb_pad() without checking the return value,
which could cause problems if any of those calls does happen
to fail. Add checks to prevent this from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX work structures must be able to run independently
of other workqueues. This is because mac80211 might use
the flush() callback function from various context, which depends
on the TX/RX work to complete while the main thread is blocked
(until the the TX queues are empty).
This should reduce the number of 'Queue %d failed to flush' warnings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During device removal all pending work and tasklets must
be guaranteed to be halted. So far only the txstatus_tasklet
was killed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both rt61pci and rt73usb check the Michael MIC in hardware and strip the
Michael MIC from received frames. This is perfectly allowed by mac80211 as
long as this is properly reported to mac80211.
Both these drivers reported the Michael MIC handling properly to mac80211, but
still contained a FIXME comment on this, which is not needed to be handled, since
mac80211 doesn't really need the Michael MIC in this case.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the specific mac field of the wcid_entry structure to copy the MAC
address to, instead of just overwriting the structure.
Previous code resulted in the same, but this form is cleaner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing a trivial comment typo.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CLOCK CYCLE: Clock cycle count in 1us
PCI:0x21, PCIE:0x7d, USB:0x1e
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove STATE_RADIO_IRQ_OFF_ISR and STATE_RADIO_IRQ_ON_ISR as they are
not used anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No driver uses interrupt threads anymore. Remove the remaining interrupt
thread artifacts.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT and PRETBTT
processing which is required to not send out beacons with a wrong DTIM
count (due to delayed periodic beacon updates). Furthermore, this
improves the latency between the TBTT and sending out buffered multi-
and broadcast traffic.
As a nice bonus, the interrupt handling overhead is reduced such that
rt2800pci gains around 25% more throuhput on a rt3052 MIPS board.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the txstatus tasklet when interrupts are enabled and disable it
together with the interrupts. Also make the txstatus tasklet useful even
without the tx status FIFO and make use of the generic rt2x00 tasklet
initialization macro.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional changes, just preparation for moving interrupt handling to
tasklets. The tasklets are disabled by default. Drivers making use of
them need to enable the tasklets when the device state is set to IRQ_ON.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow the beacondone and pretbtt functions to update the beacon from
atomic context by using the beacon update functions with caller locking.
This is a preparation for moving the periodic beacon handling into
tasklets that require atomic context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently there are two places that trigger a beacon update on PCI
devices. The bss_info_changed callback and the periodic update
triggered by the TBTT or PRETBTT interrupt.
Since the next TBTT or PRETBTT interrupt will periodically fetch an
updated beacon remove the update_beacon call in the bss_info_changed
callback for PCI devices.
In the worst case it will take one beacon interval longer to fetch
the new beacon then before. For devices that have a PRETBTT interrupt
there should be no change at all.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a beacon_update_locked function that does not acquire the
according beacon mutex to allow beacon updates from atomic context. The
caller has to take care of synchronization.
No functional changes. Just preparation for beacon updates from tasklet
context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows to dynamically remove beaconing interfaces without
shutting beaconing down on all interfaces.
The only place to start and stop beaconing are now the start- and
stop_queue callbacks. Hence, we can remove some register writes during
interface bring up (config_intf) and only write the correct sync mode
to the register there.
When multiple beaconing interfaces are present we should enable
beaconing as soon as mac80211 enables beaconing on at least one of
them. The beacon queue gets stopped when the last beaconing
interface was stopped by mac80211. Therefore, introduce another
interface counter to keep track ot the number of enabled beaconing
interfaces and start or stop the beacon queue accordingly.
To allow single interfaces to stop beaconing, add a new driver
callback clear_beacon to clear a single interface's beacon without
affecting the other interfaces. Don't overload the clear_entry callback
for clearing beacons as that would introduce additional overhead
(check for each TX queue) into the clear_entry callback which is used
on the drivers TX/RX hotpaths.
Furthermore, the write beacon callback doesn't need to enable beaconing
anymore but since beaconing should be disabled while a new beacon is
written or cleared we still disable beacon generation and enable it
afterwards again in the driver specific callbacks. However, beacon
related interrupts should not be disabled/enabled here, that's solely
done from the start- and stop queue callbacks. It would be nice to stop
the beacon queue just before the beacon update and enable it afterwards
in rt2x00queue itself instead of the current implementation that relies
on the driver doing the right thing. However, since start- and
stop_queue are mutex protected we cannot use them for atomic beacon
updates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the device id for the windy31 USB device to the rt73usb
driver.
Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value
when call rt2800_init_rfcsr
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI/PCIE radio off behavior is different from SOC/USB.
They mainly use MCU command to disable DMA, TX/RX and enter power saving mode.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
We need to release_firmware() in order not to leak memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment doesn't match the code anymore. Fix that.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the last user of intf->lock is gone we can safely remove it.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of protecting delayed_flags with a spinlock use atomic bitops to
make the code more readable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx desciptor already gets initialized to 0. Hence, there's no need
to explicitly assign 0 to mpdu_density here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Backtrace:
rt2800usb_write_tx_data
rt2x00queue_write_tx_frame
rt2x00mac_tx
invoke_tx_handlers
__ieee80211_tx
ieee80211_tx
virt_to_head_page
ieee80211_xmit
ieee80211_tx_skb
ieee80211_scan_work
schedule
ieee80211_scan_work
process_one_work
...
It tried to expand the skb past it's end using skb_put. So I replaced it
with a call to skb_padto, which takes the issue into account.
Signed-off-by: Ismael Luceno <ismael.luceno@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some pointer errors in the various calls to memcpy, memset and memmove.
Although none of these errors are fatal (the expression used now results in
the same pointer value) it is better to use the proper expression.
All errors are having to deal with arrays.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac field of the rt2x00_intf structure is written to once and used
twice. In both these uses the mac address is available via other means.
Remove this field as it does not appear to be necessary.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bssid field in struct rt2x00_intf is only written to once, and is
never read from.
Remove this field, as it appears to not be needed.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When DRIVER_REQUIRE_TXSTATUS_FIFO is set, intialize the
txstatus_fifo, but initialize rt2x00dev->txstatus_tasklet
only when both DRIVER_REQUIRE_TXSTATUS_FIFO and
rt2x00dev->ops->lib->txstatus_tasklet are set.
This allows the txstatus_fifo to be used by rt2800usb which
does not use txstatus_tasklet.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use function pci_is_pcie() instead of accessing struct member directly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Commit 6175ddf06b changes the way
memcpy_toio() works for x86_64, causing firmware loading to fail for
some Ralink WLAN devices with the rt2800pci driver since linux 2.6.34.
This causes the log message: "phy0 -> rt2800pci_load_firmware: Error -
PBF system register not ready.".
Fix this by using __iowrite32_copy instead of memcpy_toio().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pad beacon to a multiple of 32 bits in preparation for the change
from memcpy_toio() to __iowrite32_copy() in register_multiwrite().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stray semicolon after DEBUG_PRINTK_MSG causes things
like "if (...) WARNING(...); else {}" to fail with syntax error.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Queue names were incorrectly copied from the legacy drivers,
as a result the queue names were inversed to what was expected.
This renames the queues using this mapping:
QID_AC_BK -> QID_AC_VO (priority 0)
QID_AC_BE -> QID_AC_VI (priority 1)
QID_AC_VI -> QID_AC_BE (priority 2)
QID_AC_VO -> QID_AC_BK (priority 3)
Note that this was a naming problem only, which didn't affect
the assignment of frames to their respective queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a queue entry flag ENTRY_DATA_STATUS_PENDING,
which can be used to indicate a queue entry has
returned from the hardware and is waiting for
status processing. Using this flag we can add
some extra sanity checks to prevent queue corruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the rt2x00_dmastart function to rt2x00lib which
marks the queue_entry as "owned by device", and increased
the Q_INDEX number.
This cleanups up the index handling by rt2x00lib which
at until so far used hackish approaches to keep the
RX queue index numbering sane.
The rt2x00pci.c changes are from Helmut Schaa
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to the queue handlers: "flush",
this moves the flush() callback from mac80211
into rt2x00queue and adds support for flushing
the RX queue as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrapper functions in rt2x00queue.c to
start & stop queues. This control must be protected
using a mutex.
Queues can also be paused which will halt the flow
of packets between the driver and mac80211. This doesn't
require a mutex protection.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.
We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, we now introduce
3 queue commands: start, kick, stop.
- Start: will enable a queue, for TX this will
not mean anything, while for beacons and RX
this will update the registers to enable the queue.
- Kick: This will kick all pending frames to
the hardware. This is needed for the TX queue
to push all frames to the HW after the queue
has been started
- Stop: This will stop the queue in the hardware,
and cancel any pending work (So this doesn't
mean the queue is empty after a stop!).
Move all code from the drivers into the appropriate
functions, and link those calls to the old rt2x00lib
callback functions (we will fix this later when we
refactor the queue control inside rt2x00lib).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0204464329 "Check for specific changed
flags when updating the erp config" changed the way in which a new beacon
interval gets handled. However, due to a bug in rt2800usb and rt2800pci the
beacon interval was reset during each scan, thus causing problems in AdHoc
mode.
Fix this by not cleaning up the beacon interval when killing the beacon queue
but just prevent the device from sending out beacons.
Reported-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes to the TX-done code of rt2x00 resulted in TX-ed frames not
being returned to mac80211 in the original state, and therefore with
insufficient headroom for re-transmissions.
Fix this by reverting the changes done and by ensuring we remove the inserted
L2pad by moving the header backwards instead of the data forwards.
At the same time also make sure that the rt2x00queue_remove_l2pad will not
move any memory when a frame has no data at all.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Jay Hung <Jay_Hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an rt2x00 USB device is unplugged while in use, it reliably
hangs the whole system. After some time the watchdog prints:
BUG: soft lockup - CPU#0 stuck for 64s! [kworker/u:0:5]
...
[<c01a88d8>] (usb_submit_urb+0x0/0x2ac) from [<bf0e752c>] (rt2x00usb_kick_rx_entry+0xb4/0xe8 [rt2x00usb])
[<bf0e7478>] (rt2x00usb_kick_rx_entry+0x0/0xe8 [rt2x00usb]) from [<bf0e7588>] (rt2x00usb_clear_entry+x28/0x2c [rt2x00usb])
[<bf0e7560>] (rt2x00usb_clear_entry+0x0/0x2c [rt2x00usb]) from [<bf0d5bc4>] (rt2x00lib_rxdone+0x2e0/0x2f8 [rt2x00lib])
[<bf0d58e4>] (rt2x00lib_rxdone+0x0/0x2f8 [rt2x00lib]) from [<bf0e7e00>] (rt2x00usb_work_rxdone+0x54/0x74 [rt2x00usb])
[<bf0e7dac>] (rt2x00usb_work_rxdone+0x0/0x74 [rt2x00usb]) from [<c00542b4>] (process_one_work+0x20c/0x35c)
Clear the DEVICE_STATE_PRESENT flag when usb_submit_urb()
returns -ENODEV to fix this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RF chip definition
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_survey callback to allow user space to read statistics
about the current channel condition.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and modify NIC Configuration and LED definition of EEPROM
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka