There are some IP limit on rk3288 that only support 4 physical lanes
of 2.7/1.6 Gbps/lane, so seprate them out by device_type flag.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
RK3288 need some special registers setting, we can separate
them out by the dev_type of plat_data.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Both hsync/vsync polarity and interlace mode can be parsed from
drm display mode, and dynamic_range and ycbcr_coeff can be judge
by the video code.
But presumably Exynos still relies on the DT properties, so take
good use of mode_fixup() in to achieve the compatibility hacks.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
link_rate and lane_count already configured in analogix_dp_set_link_train(),
so we don't need to config those repeatly after training finished, just
remove them out.
Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets
would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Fix some obvious alignment problems, like alignment and line
over 80 characters problems, make this easy to be maintained
later.
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
In the original split we kept the register constants intact to keep the
diff small. Still the constants are Analogix-specific, so rename them now.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
An encoder is associated with a connector by the DRM core as a result of
setting up a configuration. Drivers using the atomic or legacy helpers
should never set up this link, even if it is a static one.
While at it, try to catch this kind of error in the future by adding a
WARN_ON() in drm_mode_connector_attach_encoder(). Note that this doesn't
cover all the cases, since drivers could set this up after attaching.
Drivers that use the atomic helpers will get a warning later on, though,
so hopefully the two combined cover enough to help people avoid this in
the future.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447694393-24700-1-git-send-email-thierry.reding@gmail.com
Fill atomic needed funcs with default atomic helper library.
Rockchip use dw_hdmi, and drm/rockchip will covert to atomic api,
we need dw_hdmi support atomic funcs.
Now another drm driver use dw_hdmi is imx, not yet atomic, so
check DRIVER_ATOMIC at runtime to spilt atomic and not atomic.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Seems I lied in my last drm-misc pull request and suddenly there's a big
pile of random stuff. Boris dug out Thierry's drm-trivial branch and
resubmitted everything since that branch didn't really work out.
On top of that Nicolas' changes to drm_dev_set_unique - this might
conflict with new driver pulls (I double checked and current drm-next
should be fine), so please beware. The -next/-fixes conflict in vmwgfx
will change slightly with this here too.
* tag 'topic/drm-misc-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (36 commits)
drm: use dev_name as default unique name in drm_dev_alloc()
drm: make drm_dev_set_unique() not use a format string
drm/vmwgfx: Constify function pointer structs
drm/udl: Constify function pointer structs
drm/tegra: Constify function pointer structs
drm/rockchip: Constify function pointer structs
drm/nouveau: Constify function pointer structs
drm/mgag200: Constify function pointer structs
drm/imx: Constify function pointer structs
drm/i2c/sil164: Constify function pointer structs
drm/i2c/adv7511: Constify function pointer structs
drm/exynos: Constify function pointer structs
drm/cirrus: Constify function pointer structs
drm/i2c/ch7006: Constify function pointer structs
drm/bridge/nxp-ptn3460: Constify function pointer structs
drm/bridge/dw_hdmi: Constify function pointer structs
drm/bochs: Constify function pointer structs
drm/atmel-hlcdc: Constify function pointer structs
drm/armada: Constify function pointer structs
drm: Constify drm_encoder_slave_funcs
...
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bridge/nxp-ptn3460.ko:
-.rodata 440
+.rodata 536
-.data 208
+.data 112
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-16-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Moves a bunch of junk to .rodata from .data.
drivers/gpu/drm/bridge/dw_hdmi.ko:
-.rodata 120
+.rodata 216
-.data 96
+.data 0
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-15-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just two small cleanup patches to fix coccinelle warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Q9bM
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.4-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.4-rc1
Just two small cleanup patches to fix coccinelle warnings.
* tag 'drm/panel/for-4.4-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/bridge: ptn3460: Fix coccinelle warnings
drm/bridge: ps8622: Fix coccinelle warnings
The platform_no_drv_owner.cocci coccinelle script generates the
following warning:
drivers/gpu/drm/bridge/nxp-ptn3460.c:403:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically. Patch
generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The platform_no_drv_owner.cocci coccinelle script generates the
following warning:
drivers/gpu/drm/bridge/parade-ps8622.c:671:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically. Patch
generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Given the TDMS clock, audio sample rate, and the N parameter, we can
calculate the CTS value for the audio clock regenerator (ACR) using the
following calculation given in the HDMI specification:
CTS = ftdms * N / (128 * fs)
The specification says that the CTS value is an average value, which is
true if the source hardware measures it. Where source hardware needs it
to be programmed, it is particularly difficult to alternate between two
values correctly to ensure that we achieve a correct "average"
fractional value at the sink.
Also, there's the problem that our "ftdms" is not a fully accurate
value; it is rounded to a kHz value. This introduces an unnecessary
(and harmless) fractional value into the above equation for combinations
like 148.5MHz/1.001 for 44100Hz - we still calculate the correct CTS
value.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We never set the ratio for CTS/N calculation for the audio clock
regenerator (ACR) to anything but 100, so this adds pointless
complexity. Should we support pixel repetition, we should update the
CTS/N calculation code to use those parameters or the actual TMDS clock
rate instead of a ratio.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adjust the pixel clock values in the N calculation to match the more
accurate clock values we're given by the DRM subsystem, which are the
kHz pixel rate, with any fractional kHz rounded down in the case of
the non-240, non-480 line modes, or rounded up for the others. So,
25.20 / 1.001 => 25175
27.00 * 1.001 => 27027
74.25 / 1.001 => 74176
148.50 / 1.001 => 148352
DRM derives these rates from the EDID CEA mode identifiers, which are
looked up in the tables in drivers/gpu/drm/drm_edid.c. The values on
the right are the clock values found in these tables, and are
currently expected to be passed to the HDMI driver unchanged.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to be recursive when computing the N value for the ACR
packet - we can instead calculate the multiplier prior to our switch()
based lookup, and multiply the N value appropriately afterwards.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With multichannel audio, we need to allow larger buffer sizes to avoid
XRUNs during playback. Push the buffer size up to 1024K, but as we
maintain two buffers, ensure that the vmalloc buffer does not exceed
the userspace buffer size.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add basic support for multi-channel PCM audio, with fixed speaker
mappings. This has been tested with an AV receiver, and appears to
work for low sample rates up to 8 channels.
It should be noted that multi-channel mode using the IEC958 alsa-lib
conversion plugin requires correct AES channel status for the AV
receiver to recognise the stream, especially the sample rate bits.
"Not identified" does not work there.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Parse the ELD (EDID like data) stored from the HDMI driver to restrict
the sample rates and channels which are available to ALSA. This causes
the ALSA device to reflect the capabilities of the overall audio path,
not just what is supported at the HDMI source interface level.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ALSA based HDMI AHB audio driver for dw_hdmi. The only buffer
format supported by the hardware is its own special IEC958 based format,
which is not compatible with any ALSA format. To avoid doing too much
data manipulation within the driver, we support only ALSAs IEC958 LE and
24-bit PCM formats for 2 to 6 channels, which we convert to its hardware
format.
A more desirable solution would be to have this conversion in userspace,
but ALSA does not appear to allow such transformations outside of
libasound itself.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HDMI sinks are permitted to de-assert and re-assert the HPD signal to
indicate that their EDID has been updated, which may not involve a
change of video information.
An example of where such a situation can arise is when an AV receiver
is connected between the source and the display device. Events which
can cause the HPD to be deasserted include:
* turning on or switching to standby the AV receiver.
* turning on or switching to standby the display device.
Each of these can change the entire EDID data, or just a part of the
EDID data - it's up to the connected HDMI sink to do what they desire
here. For example
- with the AV receiver and display device both in standby, a source
connected to the AV receiver may provide its own EDID to the source.
- turning on the display device causes the display device's EDID to be
made available in an unmodified form to the source.
- subsequently turning on the AV receiver then provides a modified
version of the display device's EDID.
Moreover, HPD doesn't tell us whether something is actually listening
on the HDMI TDMS signals. The phy gives us a set of RXSENSE indications
which tell us whether there is a sink connected to the TMDS signals.
Currently, we use the HPD signal to enable or disable the HDMI block,
which is questionable when HPD is used in this manner. Using the
RXSENSE would be more appropriate, but there is some bad behaviour
which needs to be coped with. The iMX6 implementation lets the TMDS
signals float when the phy is "powered down", which cause spurious
interrupts. Rather than just using RXSENSE, use RXSENSE and HPD
becoming both active to signal the presence of a device, but loss
of RXSENSE to indicate that the device has been unplugged.
The side effect of this change is that a sink deasserting the HPD
signal to cause a re-read of the EDID data will not cause the bridge
to immediately disable the video signal.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When connected to HDMI sources, some DVI monitors de-assert their HPD
signal and TDMS loads for one seconds every four seconds when there is
no signal present on the connection.
Unfortunately, this behaviour is indistinguishable from a proper HDMI
setup with an AV receiver in the path to the display: the HDMI spec
requires us to detect HPD deassertions as short as 100ms, which indicate
that the EDID has changed.
Since it is possible to connect a DVI monitor to an AV receiver and then
to a HDMI source, merely working around this by detecting the lack of
HDMI vendor block in the EDID is insufficient - the AV receiver is at
liberty to modify the EDID as it sees fit, and it will place its own
parameters into the EDID including the HDMI vendor block.
DRM has support for forcing the state of a connector, which we should
implement to allow us to work around these broken DVI monitors - we can
tell DRM to force the connection state to indicate that there is always
a device connected to work around this problem. Although this requires
manual configuration, it is better than nothing at all.
When a forced connection state has been set, there is no point handling
our RXSENSE interrupts, so disable them in this circumstance.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for interlaced video modes to the dw_hdmi bridge. This
mainly involves halving the vertical parameters to be programmed into
the bridge registers, and setting the interlace_allowed connector flag.
This brings working 1080i support. However, 480i and 576i fail to
work due to the lack of proper pixel repetition support, which is not
trivial to add due to the tabular PLL parameterisation. Hence, we
filter out these modes in our mode_valid() method.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
I2CM_ADDRESS became a MESS, fix it, also change guarding define
to __DW_HDMI_H__ , since the driver is not IMX specific.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Put the Kconfig entries for bridge drivers into a separate menu so that
they are automatically grouped and don't clutter up the top-level menu.
While at it, move the bridge menu towards the end of the top-level menu
where the panel menu is already located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Run dpms operations through the atomic intefaces. This basically removes
the .dpms() callback from econders and crtcs and use .disable() and
.enable() to turn the crtc on and off.
v2: Address comments by Joonyoung:
- make hdmi code call ->disable() instead of ->dpms()
- do not use WARN_ON on crtc enable/disable
v3: - Fix build failure after the hdmi change in v2
- Change dpms helper of ptn3460 bridge
v4: - remove win_commit() call from .enable()
v5: - move .atomic_check() to the atomic PageFlip patch, and transform it
in .atomic_begin()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Set CRTC, planes and connectors to use the default implementations from
the atomic helper library. The helpers will work to keep track of state
for each DRM object.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This header file declares prototypes of functions that are no longer
used. Remove this file and all references to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/gpu/drm/bridge/ps8622.c: In function ‘ps8622_pre_enable’:
drivers/gpu/drm/bridge/ps8622.c:368: error: implicit declaration of function ‘gpiod_set_value’
drivers/gpu/drm/bridge/ps8622.c: In function ‘ps8622_probe’:
drivers/gpu/drm/bridge/ps8622.c:584: error: implicit declaration of function ‘devm_gpiod_get’
drivers/gpu/drm/bridge/ps8622.c:584: warning: assignment makes pointer from integer without a cast
drivers/gpu/drm/bridge/ps8622.c:590: error: implicit declaration of function ‘gpiod_direction_output’
drivers/gpu/drm/bridge/ps8622.c:596: warning: assignment makes pointer from integer without a cast
Add the missing #include <linux/gpio/consumer.h> to fix this.
Fixes: f1336e6afb ("drm/bridge: Add I2C based driver for ps8622/ps8625 bridge")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
If GPIOLIB=n and asm-generic/gpio.h is not used:
drivers/gpu/drm/bridge/ptn3460.c: In function ‘ptn3460_pre_enable’:
drivers/gpu/drm/bridge/ptn3460.c:135: error: implicit declaration of function ‘gpiod_set_value’
drivers/gpu/drm/bridge/ptn3460.c: In function ‘ptn3460_probe’:
drivers/gpu/drm/bridge/ptn3460.c:333: error: implicit declaration of function ‘devm_gpiod_get’
drivers/gpu/drm/bridge/ptn3460.c:333: warning: assignment makes pointer from integer without a cast
drivers/gpu/drm/bridge/ptn3460.c:340: error: implicit declaration of function ‘gpiod_direction_output’
drivers/gpu/drm/bridge/ptn3460.c:346: warning: assignment makes pointer from integer without a cast
Add the missing #include <linux/gpio/consumer.h> to fix this.
Fixes: af478d8823 ("drm/bridge: ptn3460: use gpiod interface")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dw_hdmi_connector_get_modes() function accidentally forgets to
return the number of modes it added, although it has this information
stored in a local variable. Let's fix that.
Without this fix, drm_helper_probe_single_connector_modes_merge_bits()
could get confused and always call drm_add_modes_noedid(). That's not
right.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
I2C drivers that support OF, have both an I2C and OF device ID tables
that are used to fill the supported module aliases. But currently the
I2C core only uses the OF table to match a device with a driver and
the aliases information are always reported in the form i2c:<name>.
The client->name is used as the name postfix and when booting with OF
this is obtained with of_modalias_node() which drops the compatible
string vendor prefix.
So for I2C drivers, the I2C and OF device ID tables should be keep in
sync in order to make module auto-loading to work but the I2C device
entries shouldn't have the vendor prefix since that is not reported.
Before this patch:
MODALIAS=i2c:ptn3460
$ modinfo | grep alias
alias: i2c:nxp,ptn3460
alias: of:N*T*Cnxp,ptn3460*
After this patch:
MODALIAS=i2c:ptn3460
$ modinfo | grep alias
alias: i2c:ptn3460
alias: of:N*T*Cnxp,ptn3460*
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Staticize dw_hdmi_bridge_funcs to fix the following sparse warning:
drivers/gpu/drm/bridge/dw_hdmi.c:1458:25: warning: symbol 'dw_hdmi_bridge_funcs' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This set of patches adjust the setup of the HDMI CTS/N values for audio
support to be compliant with the work-around given in the iMX6 errata
documentation as part of the preparation for integrating audio support
for this driver, and also update the HDMI phy configuration for Rockchip
devices to improve the HDMI eye pattern.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: rockchip/dw_hdmi-rockchip: improve for HDMI electrical test
drm: bridge/dw_hdmi: separate VLEVCTRL settting into platform driver
drm: bridge/dw_hdmi: fixed codec style
drm: bridge/dw_hdmi: adjust n/cts setting order
drm: bridge/dw_hdmi: protect n/cts setting with a mutex
drm: bridge/dw_hdmi: combine hdmi_set_clock_regenerator_n() and hdmi_regenerate_cts()
Conflicts:
drivers/gpu/drm/imx/dw_hdmi-imx.c
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using a local struct pointer to reduce one level of indirection
makes the code slightly more readable.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch derived from one from Yakir Yang. Yakir Yang says:
For Designerware HDMI, the following write sequence is recommended:
1. aud_n3 (set bit ncts_atomic_write if desired)
2. aud_cts3 (set CTS_manual and CTS value if desired/enabled)
3. aud_cts2 (required in CTS_manual)
4. aud_cts1 (required in CTS_manual)
5. aud_n3 (bit ncts_atomic_write with same value as in step 1.)
6. aud_n2
7. aud_n1
However, avoid the ncts_atomic_write_bit and CTS_manual settings in this
patch, both of which are marked reserved in the iMX6 documentation. All
iMX6 code in the wild seems to want CTS_manual cleared.
Having requested clarification from FSL, it appears that neither of
these bits are implemented in their version of the IP.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HDMI n/cts settings need to be updated whenever the audio sample
rate or the video pixel clock changes. This needs to be protected
against concurrency as there is no synchronisation between these two
operations. Introduce a mutex (called audio_mutex) to protect against
two threads trying to update the video clock rate and pixel clock
simultaneously.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine these two functions into a single implementation. These two
functions are called consecutively anyway. Idea from a patch by
Yakir Yang.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ps8622_attach and ps8522_driver symbols are never used outside this
file, so they should be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit fbc4572e9c48e45b ("drm/bridge: make bridge registration independent of
drm flow") introduced some drm/bridge API modifications. Make the necessary
changes so that we can avoid the build breakage:
drivers/gpu/drm/bridge/dw_hdmi.c: In function 'dw_hdmi_bridge_destroy':
drivers/gpu/drm/bridge/dw_hdmi.c:1378:2: error: implicit declaration of function 'drm_bridge_cleanup' [-Werror=implicit-function-declaration]
drivers/gpu/drm/bridge/dw_hdmi.c: At top level:
drivers/gpu/drm/bridge/dw_hdmi.c:1471:2: error: unknown field 'destroy' specified in initializer
drivers/gpu/drm/bridge/dw_hdmi.c: In function 'dw_hdmi_register':
drivers/gpu/drm/bridge/dw_hdmi.c:1535:2: error: implicit declaration of function 'drm_bridge_init' [-Werror=implicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If devm_request_threaded_irq() fails we should jump to 'err_iahb' label that
will disable the clocks that were previously enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Force bridge connector detection at the end of the bridge attach.
This is needed to detect the bridge connector early.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add drm_panel calls to the driver to make the panel and
bridge work together in tandem.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch does the following changes:
-- Use usleep_range instead of udelay.
-- Remove driver_private member from ptn3460 structure.
-- Make all possible functions and structures static.
-- Use dev_err for non-DRM errors.
-- Arrange header files alphabetically.
-- s/edid/EDID in all error messages.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The encoder ->prepare() and ->mode_set() methods need to use the
hw adjusted mode, not the original mode.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Otherwise a spurious interrupt might trigger (and crash) the interrupt handler
before probing finished.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Rockchip RK3288 hdmi is compatible with dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
RK3288 HDMI will not work without the spare bit of
HDMI_PHY_CONF0 enable
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
HDMI_IH_I2CMPHY_STAT0 is a clear on write register, which indicates i2cm
operation status(i2c transfer done or error), every hdmi phy register
configuration must check this register to make sure the configuration
has complete. But the indication bit should be cleared after check, otherwise
the corresponding bit will hold on forever, this may give a wrong signal for
next check.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
some platform may not support all the display mode,
add mode_valid interface check it
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On rockchip rk3288, only word(32-bit) accesses are
permitted for hdmi registers. Byte width accesses (writeb,
readb) generate an imprecise external abort.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
the original imx hdmi driver is under drm/imx/,
which depends on imx-drm, so move the imx hdmi
driver out to drm/bridge and rename it to dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch exports ptn3460_init function so that other modules
can call this function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The recently added PTN3460 device driver uses interfaces that
are provided by the KMS helper infrastructure, so we should
explicitly select that to avoid this linker error:
ERROR: "drm_helper_probe_single_connector_modes" [drivers/gpu/drm/bridge/ptn3460.ko] undefined!
ERROR: "drm_helper_connector_dpms" [drivers/gpu/drm/bridge/ptn3460.ko] undefined!
We have to drop the I2C dependency to avoid a circular dependency
chain, but that's ok because DRM already selects I2C.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a drm_bridge driver for the PTN3460 DisplayPort to LVDS
bridge chip.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Yakir Yang