AM437x EPOS evm use external clock for RMII interface.
Enable the same in DT.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MTD NAND partition for file-system should start at offset=0xA00000
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux for hdq/1wire on
am43x epos evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixup Y resolution and add default pin state. Also update
the compatible id.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am43x-epos-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add card detect gpio for SD card slot and include dt gpio header.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch:
- enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
- adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
present on following boards:
am43x-epos-evm:
On this board, NAND Flash control lines are muxed with QSPI, Thus only
one of the two can be used at a time. Selection is controlled by:
(a) dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
George Cherian