This can be used to have GPIO host wakeup method suitable for the
platform and configurable GAP for host sleep handshake.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Calibration data can be downloaded through device tree method. This
patch adds the documentation. Also, instead of searching device tree
node by name using of_find_node_by_name() API, let's use
for_each_compatible_node().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Correct the comments in this driver. Set the CRTSCTS flag means
automatic flow control is enabled.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of having the driver generate the HCI Hardware Error event
manually, just call hci_reset_dev() to trigger the upper stack reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When constructing the event payload for the HCI_Hardware_Error event
message, use the HCI_EV_HARDWARE_ERROR define.
In addition rename the variables from hard_err to hw_err to clearly
indicate that this is about the hardware error and not a hard error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
H5 Specification says:
If a SYNC message is received while in the Active State, it is
assumed that the peer device has reset. The local device should
therefore perform a full reset of the upper stack, and start Link
Establishment again at the Uninitialized State. Upon entering the
Active State, the first packet sent shall have its SEQ and ACK
numbers set to zero.
This patch resets the HCI H5 driver data/state to unitialized and
reports an HCI hardware error event to notify the upper stack that
HCI synchronization has been lost. H5 will be re-synchronized and
upper stack should generate an HCI Reset command.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
This patch adds driver support for marvell SD8887 chip.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register offsets are different for SD8897 and newer chip SD8887.
We can not have common btmrvl_sdio_card_reg map for them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving USB interrupt, bulk or isochronous packet, they normally
come in fragments. So far the driver just handed each fragment off to
the hci_recv_fragment function of the Bluetooth core. That function is
however so specific that is does not belong in the core. This patch
implements the same reassembly logic in the driver.
In addition this fixes a long standing bug where multiple complete
packets are received within a single USB packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The actual packet reassembly should be done inside the driver. To allow
this to happen cleanly in future patches, split the fragment reception
into its own functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb driver has been around for a while now and it is time to
bring its coding style in sync with what has been done for the
Bluetooth subsystem and other drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The complete TX URB handling is done via a switch statement in the
btusb_send_frame function. To allow for more clear separation between
control, bulk and isoc URBs, split them into allocation and submission.
Previously the inc_tx function has been used for tracking in-flight
URB for HCI commands and ACL data packets. Convert that into a common
function that either submits the URB or queues it when needed.
This provides the flexibility to allow vendor specific hdev->send_frame
callbacks without having to duplicate the whole URB handling logic.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All hdev->send() calls are these days done through a work queue. For the
btusb driver this means the btusb_send_frame() function. Because of this
we can safely use GFP_KERNEL for all memory allocations in this code
path.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Suspend could fail for some platforms because
btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs.
When btusb_bulk_complete returns before system suspend and resubmits
an URB, the system cannot enter suspend state.
Signed-off-by: Champion Chen <champion_chen@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
bt3c_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for nsh_t and
dtl1_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case for dtl1_info_t
and a similar patch finds the nsh_t case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
btuart_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
bluecard_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In this expression: seq = (seq - 1) % 8
seq (u8) is implicitly converted to an int in the arithmetic operation.
So if seq value is 0, operation is ((0 - 1) % 8) => (-1 % 8) => -1.
The new seq value is 0xff which is an invalid ACK value, we expect 0x07.
It leads to frequent dropped ACK and retransmission.
Fix this by using '&' binary operator instead of '%'.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
btmrvl_add_card() function calls kthread_run that might return error
(e.g. if current thread is killed). If one tries to use the error
value as a pointer then invalid memory access oops happens.
Check kthread_run() return value, if it is an error then release resources
correctly.
TEST=boot computer with BT modules enabled. I see the error message that
BT device initialization failed. Now kernel does not crash. Hint: to enable
BT run 'rmmod btmrvl_sdio; modprobe btmrvl_sdio'
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ath3k driver is treating the version information badly when it
comes to loading the right firmware version and comparing that it
actually matches with the hardware.
Initially this showed up as this:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:373:17: warning: cast to restricted __le32
drivers/bluetooth/ath3k.c:435:17: warning: cast to restricted __le32
However when fixing this by actually using __packed and __le32 for
the ath3_version structure, more issues came up:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:381:32: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:381:32: expected restricted __le32 [usertype] rom_version
drivers/bluetooth/ath3k.c:381:32: got int [signed] <noident>
drivers/bluetooth/ath3k.c:382:34: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:382:34: expected restricted __le32 [usertype] build_version
drivers/bluetooth/ath3k.c:382:34: got int [signed] <noident>
drivers/bluetooth/ath3k.c:386:28: warning: restricted __le32 degrades to integer
drivers/bluetooth/ath3k.c:386:56: warning: restricted __le32 degrades to integer
This patch fixes every instance of the firmware version handling and
makes sure it is endian safe and uses proper unaligned access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
.set_bdaddr handler is implemented for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implemented .set_bdaddr handler provided by bluetooth stack for
Marvell devices for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should suspend hci device and purge remaining data in tx queue
before enabling host sleep in firmware. If any data is sent to
firmware after host sleep is activated, firmware may end up
sending a TX_DONE interrupt to driver. If this interrupt gets
delivered to host while the SDIO host controller is suspending,
it may crash the system.
Conversely, in resume handler, we should resume hci device after
host sleep is de-activated.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The protocol for the UART might be configured, but that does not
mean the HCI device is registered. Return an error in that case
and only return the index number when HCI_UART_REGISTERED is set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The quirk for enabling external configuration with UART needs to be
provided via the HCI UART flags. Add a new flag for it and declare
it as valid.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing unknown or invalid flags to the HCI UART driver should
result in an error. So check which flags are valid and otherwise
return an error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to
indicate that isochronous endpoints are not needed for CSR USB
sniffer devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The interrupt interface for the Intel USB bootloader devices is only
enabled after receiving SetInterface(0, AltSetting=0). When this USB
command is not send, then no HCI events will be received.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The module parameters to ignore devices based on USB VID/PID are not
needed at all. So just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for configuring the hci_vhci virtual controllers
to require a setup stage using HCI_QUIRK_EXTERNAL_CONFIG. With this
option the virtual controller will start out as unconfigured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Broadcom USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Intel USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for configuring the hci_vhci virtual controllers
as a raw-only device using HCI_QUIRK_RAW_DEVICE. This is useful for
testing the kernel internal infrastructure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes the following sparse warning caused by a missing
declaration in the header file:
drivers/bluetooth/btmrvl_main.c:218:5: warning: symbol 'btmrvl_pscan_window_reporting' was not declared. Should it be static?
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom BCM20702A0 USB controllers might come with the default
address 00:20:70:02:A0:00 when booting up. If this happens, then warn
about such address being used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Intel Bluetooth controllers come with a default address. If this
address is found, print an error to warn the user about it.
The controller is fully operational, but the danger of duplicate
Bluetooth addresses might causes issues. At least with a clear
error it becomes easier to debug these cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Intel based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Broadcom based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After BT_CMD_HOST_SLEEP_ENABLE command finishes, driver should
wait until getting BT_EVENT_HOST_SLEEP_ENABLE event to complete
suspend procedure.
Without this patch the suspend handler would return success
earlier. By the time when the BT_EVENT_HOST_SLEEP_ENABLE event
comes in the controller driver could have already turned off the
bus clock. This causes kernel crash or system reboot eventually.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Jeff CF Chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A vendor specific command is sent to firmware during
initialization to enable this feature. This command is for
SD8897 only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
h5_reset_rx is unconditionally called at the end of
h5_complete_rx_pkt, no need to call it anymore after
that.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This reverts commit ca58e594da.
For some unclear reason this patch tries to add suport for the
product ID 0xe005, but it ends up adding product ID 0x3005 to
all the tables. This is obviously wrong and causing multiple
issues.
The original patch seemed to be fine, but what ended up in 3.15
is not what the patch intended. The commit 0a3658cccd is
already present and adds support for this hardware. This means
only revert of this broken commit is requird.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Alexander Holler <holler@ahsoftware.de>
Cc: stable@vger.kernel.org # 3.15.x
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXgoACgkQMUfUDdst+ymdSwCgwL0xmWjFYr/UbJ4LslOZ29Q4
BFQAoKyYe9LsfEyodBPabxJjKUtj1htz
=ZGSN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into next
Pull tty/serial driver updates from Greg KH:
"Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while"
* tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
Revert "serial: imx: remove the DMA wait queue"
serial: kgdb_nmi: Improve console integration with KDB I/O
serial: kgdb_nmi: Switch from tasklets to real timers
serial: kgdb_nmi: Use container_of() to locate private data
serial: cpm_uart: No LF conversion in put_poll_char()
serial: sirf: Fix compilation failure
console: Remove superfluous readonly check
console: Use explicit pointer type for vc_uni_pagedir* fields
vgacon: Fix & cleanup refcounting
ARM: tty: Move HVC DCC assembly to arch/arm
tty/hvc/hvc_console: Fix wakeup of HVC thread on hvc_kick()
drivers/tty/n_hdlc.c: replace kmalloc/memset by kzalloc
vt: emulate 8- and 24-bit colour codes.
printk/of_serial: fix serial console cessation part way through boot.
serial: 8250_dma: check the result of TX buffer mapping
serial: uart: add hw flow control support configuration
tty/serial: at91: add interrupts for modem control lines
tty/serial: at91: use mctrl_gpio helpers
tty/serial: Add GPIOLIB helpers for controlling modem lines
ARM: at91: gpio: implement get_direction
...
Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After hardware reset, some BCM Bluetooth adapters obtain their initial firmware
from OTPROM chip. Once this initial firmware is running, the firmware can be
further upgraded over HCI interface with .hcd files provided by Broadcom. This
is also known as "patch RAM" support. This change implements that.
If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues
to operate with the initial firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found
If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and
it starts using the new firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e
Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit d2bee8fb6e.
Enabling autosuspend for Intel Bluetooth devices has been shown to not
work reliable. It does work for some people with certain combinations
of USB host controllers, but for others it puts the device to sleep and
it will not wake up for any event.
These events can be important ones like HCI Inquiry Complete or HCI
Connection Request. The events will arrive as soon as you poke the
device with a new command, but that is not something we can do in
these cases.
Initially there were patches to the xHCI USB controller that fixed
this for some people, but not for all. This could be well a problem
somewhere in the USB subsystem or in the USB host controllers or
just plain a hardware issue somewhere. At this moment we just do
not know and the only safe action is to revert this patch.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Tedd Ho-Jeong An <tedd.an@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
LDISCs shouldn't call tty->ops->write() from within
->write_wakeup().
->write_wakeup() is called with port lock taken and
IRQs disabled, tty->ops->write() will try to acquire
the same port lock and we will deadlock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Andreas Bießmann <andreas@biessmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change subcmd parameter from int to u8 to match its use:
btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure no timer callback is running before releasing the
datastructure which contains it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If vendor specific HCI commands are received from application,
we should send corresponding events to stack.
These events should be consumed in driver, only if they are for
the internal HCI commands generated by driver.
This patch fixes the vendor command 0x3f stuck problem with
above mentioned change. For example,
hcitool cmd 3f 22 fe 06 22 21 20 43 50 00
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The version is always in little endian format. This patch makes the
driver work on both little and big endian CPUs.
Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove assignment in if-statements to be consistent with the coding
style.
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When stopping BCSP/H5, stop the retransmission timer before proceeding
to clean up packet queues. The previous code had a race condition where
the timer could trigger after the packet lists and protocol structure
had been removed which led to dereferencing NULL or use-after-free bugs.
Signed-off-by: Michael Knudsen <m.knudsen@samsung.com>
Reported-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This will help to manage table of supported IDs.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit bfacbb9 (Bluetooth: Use devname:vhci module alias for virtual HCI
driver) added the module alias to hci_vhci module so it's possible to
create the /dev/vhci node. However creating an alias without
specifying the minor doesn't allow us to create the node ahead,
triggerring module auto-load when it's first accessed.
Starting with depmod from kmod 16 we started to warn if there's a
devname alias without specifying the major and minor.
Let's do the same done for uhid, kvm, fuse and others, specifying a
fixed minor. In systems with systemd as the init the following will
happen: on early boot systemd will call "kmod static-nodes" to read
/lib/modules/$(uname -r)/modules.devname and then create the nodes. When
first accessed these "dead" nodes will trigger the module loading.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x3000
LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
Manufacturer: Broadcom Corporation (15)
The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.
For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.
During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.
Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.
What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.
T: Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.00
S: Manufacturer=Bluetooth v2.0
S: Product=Bluetooth V2.0 Dongle
T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 0.07
In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The register for setting the SDIO card mode of a Type-B Bluetooth card
is called MD SET. The MD STAT register is used for reading the current
mode back.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth virtual HCI driver is using a misc character device to
allow emulation of HCI devices from userspace. This change enables the
support for vectored writes. Previously this was failing with EINVAL
since no complete H:4 packet was written.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Socket Bluetooth SDIO cards are branded versions of Toshiba SD-BT2
and they do not support sending HCI_Reset as first command. To make
this card work the HCI_QUIRK_RESET_ON_CLOSE quirk needs to be set
before registering the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch enables autosuspend for Intel Bluetooth device.
After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.
"The USB specification states that all USB devices must support power
management. Nevertheless, the sad fact is that many devices do not
support it very well. You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely. This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.
For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs. Hubs, at least, appear to be reasonably well-behaved in
this regard."
This document also described how the driver can enables the autosuspend
by using an USB api.
"Drivers can enable autosuspend for their devices by calling
usb_enable_autosuspend(struct usb_device *udev);
in their probe() routine, if they know that the device is capable of
suspending and resuming correctly. This is exactly equivalent to
writing "auto" to the device's power/control attribute."
For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device tree property can define the cal-data in proper order.
There is no need to swap the bytes in driver.
Also remove the redundant cal-data memory copy after removing the
byte swapping.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some ARM versions of Chromebook need to download a new calibration
data from host driver to firmware. They do have EEPROM but still
need a piece of new calibration data in test mode.
The cal-data is platform dependent. It's simpler and more feasible
to use device tree based cal-data instead of configuration file
based cal-data.
This patch remove configuration file based cal-data downloading
and replace it using cal-data from device tree.
When CONFIG_OF is not selected, or the specific property is not
present in the device tree, the calibration downloading will not
happen.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ath3k_table[] and ath3k_blist_tbl[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bpa10x_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of vhci_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of hci_uart_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of dtl1_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btuart_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btmrvl_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bt3c_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bluecard_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bfusb_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The function h4_check_data_len() is actually not used. So just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btmrvl_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The dtl1_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btuart_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt3c_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bluecard_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.
In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These
devices default to hid mode for BIOS use. This means that after having been
reset they will revert to HID mode, and are no longer usable as a HCI.
Therefor it is a very bad idea to just blindly make reset_resume point to
the regular resume handler. Note that the btusb driver has no clue how to
switch these devices from hid to hci mode, this is done in userspace through
udev rules, so the proper way to deal with this is to not have a reset-resume
handler and instead let the usb-system re-enumerate the device, and re-run
the udev rules.
I must also note, that the commit message for the commit causing this
problem has a very weak motivation for the change:
"Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?"
Making a change solely to silence a warning while also changing important
behavior (normal resume handling versus re-enumeration) requires a commit
message with a proper explanation why it is safe to do so, which clearly lacks
here, and unsurprisingly it turns out to not be safe to make this change.
Reverting the commit in question fixes bt no longer working on my Dell
E6430 after a suspend/resume, and I believe it likely also fixes the
following bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=988481https://bugzilla.redhat.com/show_bug.cgi?id=1010649https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239
This reverts commit 502f769662.
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A text file containing calibration data in hex format can
be provided at following path:
/lib/firmware/mrvl/sd8797_caldata.conf
The data will be downloaded to firmware during initialization.
Reviewed-by: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace this proprietary structure with the standard one
(struct hci_command_hdr).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Command preparation code is used multiple times. This patch
separate out this common code and create btmrvl_send_sync_cmd()
function.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth protocol and hardware is pretty much all little endian
and so when running sparse via "make C=2" for example, enable the
endian checks by default.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
So far the only option to create a virtual AMP controller was by
setting a module parameter for the hci_vhci driver. This patch adds
the functionality to define inline to create either a BR/EDR or an
AMP controller.
In addition the client will be informed which HCI controller index
it got assigned. That is especially useful for automated end-to-end
testing.
To keep backwards compatibility with existing userspace, the command
for creating a controller type needs to be send right after opening
the device node. If the command is not send, it defaults back to
automatically creating a BR/EDR controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
To allow creating /dev/vhci device node, add the proper module alias for
this driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There are two places where DIV_ROUND_UP may be used. It makes code a bit
clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Memory allocated by vmalloc (including stack) can not be used for DMA,
i.e. data pointer on usb_control_msg() should not point to stack memory.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=977558
Reported-and-tested-by: Andy Lawrence <dr.diesel@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Fix to return -ENOMEM in the skb alloc error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar