Replace all remaining callers of alloc_maybe_bootmem with
zalloc_maybe_bootmem. The callsite in pci_dn is followed with a
memset to clear the memory, and not zeroing at the other callsites
in the celleb fake pci code could lead to following uninitialized
memory as pointers or even freeing said pointers on error paths.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Its unused, and of the three declarations, one is duplicated in pmac.h,
the second is static and the third is renamed and static.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that MSG_ALL and MSG_ALL_BUT_SELF have been eliminated,
smp_mpic_mesage_pass no longer needs to lookup the cpumask just to
have mpic_send_ipi extract part of it and recode it in a NR_CPUS loop
by mpic_physmask.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that smp_ops->smp_message_pass is always called with an (online) cpu
number for the target remove the checks for MSG_ALL and MSG_ALL_BUT_SELF.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only user of MSG_ALL_BUT_SELF in the whole kernel tree is powerpc,
and it only uses it to start the debugger. Both debuggers always call
smp_send_debugger_break with MSG_ALL_BUT_SELF, and only mpic can do
anything more optimal than a loop over all online cpus, but all message
passing implementations have to code for this special delivery target.
Convert smp_send_debugger_break to take void and loop calling the smp_ops
message_pass function for each of the other cpus in the online cpumask.
Use raw_smp_processor_id() because we are either entering the debugger
or trying to start kdump and the additional warning it not useful were
it to trigger.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_set_affinity is allocating and freeing a cpumask var even though
it was breaking the cpumask abstraction when passing the mask to
mpic_physmask. It also didn't have any check for allocatin failure.
Break the cpumask abstraction earlier and use simple bitwise and of the
bits from the mask with the bits of cpu_online_mask.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_physmask was looping NR_CPUS times over a mask that was passed as
a u32. Since mpic is architecturaly limited to 32 physical cpus, clamp
the logical cpus to 32 when compiling (we could also clamp at runtime
to nr_cpu_ids).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
c1854e0072 (powerpc: Set nr_cpu_ids early
and use it to free PACAs) copied the formerly static setup_nr_cpu_ids
from init/main.c but 34db18a054 (smp:
move smp setup functions to kernel/smp.c) moved it to kernel/smp.c
with a declaration in include/linux/smp.h, so we can call it instead of
replicating it.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we never set a cpu above nr_cpu_ids possible we can
limit our initial paca allocation to nr_cpu_ids. We can then
clamp the number of cpus in platforms/iseries/setup.c.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should not set cpus above nr_cpu_ids to possible. While we
will trigger a warning with CONFIG_CPUMASK_DEBUG, even then the mask
initializers will set the bits beyond what the iterators check and cause
nr_cpu_ids to increase.
Respecting nr_cpu_ids during setup will allow us to use it in our initial
paca allocation. It can be reduced from NR_CPUS by the existing early param
nr_cpus=, which was added in 2b633e3fac (smp:
Use nr_cpus= to set nr_cpu_ids early). We already call parse_early_parms
between finding the command line and allocating the pacas.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
9cb82f2f46 (Make iSeries spin on
__secondary_hold_spinloop, like pSeries) added a load of current_set
but this load was repeated later and we don't even have the paca yet.
It also checked __secondary_hold_spinloop with a 32 bit compare instead
of a 64 bit compare.
b6f6b98a4e (Don't spin on sync instruction
at boot time) missed the copy of the startup code in iseries.
1426d5a3bd (Dynamically allocate pacas)
doesn't allow for pacas to be less than lppacas and recalculated the paca
location from the cpu id in r0 every time through the secondary loop.
Various revisions over time made the comments on conditional branches
confusing with respect to being a hold loop or forward progress
Mostly in-order description of the changes:
Replicate the few lines of code saved by the ugly scoped ifdef CONFIG_SMP
in the secondary loop between yielding on UP and marking time with the
hypervisor on SMP. Always compile the iseries_secondary_yield loop and
use it if the cpu id is above nr_cpu_ids. Change all forward progress
paths to be forward branches to the next numerical label. Assign a
label to all loops. Move all sync instructions from the loops to the
forward progress path. Wait to load current_set until paca is set to go.
Move the iseries_secondary_smp_loop label to cover the whole spin loop.
Add HMT_MEDIUM when we make forward progress.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Starting with 1426d5a3bd (powerpc:
Dynamically allocate pacas) the space for pacas beyond cpu_possible
is freed, but we failed to update the loop in crash.c.
Since c1854e0072 (powerpc: Set nr_cpu_ids
early and use it to free PACAs) the number of pacas allocated is
always nr_cpu_ids.
Signed-off-by: Milton Miller <miltonm@bga.com>
Cc: <stable@kernel.org> # .34.x
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Starting with 1426d5a3bd (powerpc:
Dynamically allocate pacas) we free the memory for pacas beyond
cpu_possible, but we failed to update the loop the secondary cpus use
to find their paca. If the system has running cpu threads for which
the kernel did not allocate a paca for they will search the memory that
was freed. For instance this could happen when the device tree for
a kdump kernel was not updated after a cpu hotplug, or the kernel is
running with more cpus than the kernel was configured.
Since c1854e0072 (powerpc: Set nr_cpu_ids
early and use it to free PACAs) we set nr_cpu_ids before telling the
cpus to advance, so use that to limit the search.
We can't reference nr_cpu_ids without CONFIG_SMP because it is defined
as 1 instead of a memory location, but any extra threads should be sent
to kexec_wait in that case anyways, so make that explicit and remove
the search loop for UP.
Note to stable: The fix also requires
c1854e0072 (powerpc: Set
nr_cpu_ids early and use it to free PACAs) to function. Also
9d07bc841c (Properly handshake CPUs going
out of boot spin loop) affects the second chunk, specifically the branch
target was 3b before and is 4b after that patch, and there was a blank
line before the #ifdef CONFIG_SMP that was removed
Cc: <stable@kernel.org> # .34.x: c1854e0072 powerpc: Set nr_cpu_ids early
Cc: <stable@kernel.org> # .34.x
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 1fc711f7ff (powerpc/kexec: Fix race
in kexec shutdown) moved the write to signal the cpu had exited the kernel
from before the transition to real mode in kexec_smp_wait to kexec_wait.
Unfornately it missed that kexec_wait is used both by cpus leaving the
kernel and by secondary slave cpus that were not allocated a paca for
what ever reason -- they could be beyond nr_cpus or not described in
the current device tree for whatever reason (for example, kexec-load
was not refreshed after a cpu hotplug operation). Cpus coming through
that path they will write to paca[NR_CPUS] which is beyond the space
allocated for the paca data and overwrite memory not allocated to pacas
but very likely still real mode accessable).
Move the write back to kexec_smp_wait, which is used only by cpus that
found their paca, but after the transition to real mode.
Signed-off-by: Milton Miller <miltonm@bga.com>
Cc: <stable@kernel.org> # (1fc711f was backported to 2.6.32)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a report of an FWNMI with an r3 value that we think is
corrupt, but since we don't print r3 we have no idea what was
wrong with it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we swtich to direct dma ops, we set the dma data union to have the
dma offset. When we switch back to iommu table ops because of a later
dma_set_mask, we need to restore the iommu table pointer. Without this
change, crashes have been observed on kexec where (for reasons still
being investigated) we fall back to a 32-bit dma mask on a particular
device and then panic because the table pointer is not valid.
The easiset way to find this value is to call
pci_dma_dev_setup_pSeriesLP which will search up the pci tree until it
finds the node with the table.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Milton Miller <miltonm@bga.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a confusing number of ioremap functions. Make things just a
bit simpler by merging ioremap_flags and ioremap_prot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ioremap_wc so drivers can request write combining on kernel
mappings.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After looking at our system call path, Mary Brown suggested that we
should put all mfspr SRR* instructions before any mtspr SRR*.
To test this I used a very simple null syscall (actually getppid)
testcase at http://ozlabs.org/~anton/junkcode/null_syscall.c
I tested with the following changes against the pseries_defconfig:
CONFIG_VIRT_CPU_ACCOUNTING=n
CONFIG_AUDIT=n
to remove the overhead of virtual CPU accounting and syscall
auditing.
POWER6:
baseline: mean = 757.2 cycles sd = 2.108
modified: mean = 759.1 cycles sd = 2.020
POWER7:
baseline: mean = 411.4 cycles sd = 0.138
modified: mean = 404.1 cycles sd = 0.109
So we have 1.77% improvement on POWER7 which looks significant. The
POWER6 suggest a 0.25% slowdown, but the results are within 1
standard deviation and may be in the noise.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A static branch hint will override dynamic branch prediction on
recent POWER CPUs. Since we are about to use more altivec in the
kernel remove the static hint in giveup_altivec that assumes
a userspace task is using altivec.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To make it easier to add optimised versions of copy_page, remove
the 4kB loop for 64kB pages and just do all the work in copy_page.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable iSCSI support for a number of cards. We had the base
networking devices enabled but forgot to enable iSCSI.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable the Qlogic and Emulex 10Gbit adapters.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The variable 'old' is set but not used in the wrprotect functions in
arch/powerpc/include/asm/pgtable-ppc64.h, which can trigger a compiler warning.
Remove the variable, since it's not used anyway.
Signed-off-by: Stratos Psomadakis <psomas@ece.ntua.gr>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Future releases of fimrware will enforce a requirement that DTL buffers
do not cross a 4k boundary. Commit
127493d5dc satisfies this requirement for
CONFIG_VIRT_CPU_ACCOUNTING=y kernels, but if !CONFIG_VIRT_CPU_ACCOUNTING
&& CONFIG_DTL=y, the current code will fail at dtl registration time.
Fix this by making the kmem cache from
127493d5dc visible outside of setup.c and
using the same cache in both dtl.c and setup.c. This requires a bit of
reorganization to ensure ordering of the kmem cache and buffer
allocations.
Note: Since firmware now limits the size of the buffer, I made
dtl_buf_entries read-only in debugfs.
Tested with upcoming firmware with the 4 combinations of
CONFIG_VIRT_CPU_ACCOUNTING and CONFIG_DTL.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we kexec we look for a particular property added by the first
kernel, "linux,direct64-ddr-window-info", per-device where we already
have set up dynamic dma windows. The current code, though, wasn't
initializing the size of this property and thus when we kexec'd, we
would find the property but read uninitialized memory resulting in
garbage ddw values for the kexec'd kernel and panics. Fix this by
setting the size at enable_ddw() time and ensuring that the size of the
found property is valid at dupe_ddw_if_kexec() time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch below removes an unused config variable found by using a kernel
cleanup script.
Note: I did try to cross compile these but hit erros while doing so..
(gcc is not setup to cross compile) and am unsure if anymore needs to be done.
Please have a look if/when anybody has free time.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The timestamps recorded in the .gz files add no value.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit c56e58537d breaks SMP support in PPC_47x chip.
secondary_ti must be set to current thread info before callin kick_cpu or else
start_secondary_47x will jump into void when trying to return to c-code.
In the current setup secondary_ti is initialized before the CPU idle task is started
and only the boot core will start. I am not sure this is the correct solution, but it
makes SMP possible in my chip.
Note! The HOTPLUG support probably need some fixing to, There is no trampoline code
available in head_44x.S - start_secondary_resume?
Signed-off-by: Kerstin Jonsson <kerstin.jonsson@ericsson.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b987812b3f left
crash_kexec_wait_realmode() undefined for UP.
Commit 7c7a81b53e defined it for UP but
left it undefined for 32-bit SMP.
Seems like people are getting confused by nested #ifdef's, so move the
definitions of crash_kexec_wait_realmode() after the #ifdef CONFIG_SMP
section.
Compile-tested with 32-bit UP, 32-bit SMP and 64-bit SMP configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* syscore:
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
ARM / Samsung: Use struct syscore_ops for "core" power management
ARM / PXA: Use struct syscore_ops for "core" power management
ARM / SA1100: Use struct syscore_ops for "core" power management
ARM / Integrator: Use struct syscore_ops for core PM
ARM / OMAP: Use struct syscore_ops for "core" power management
ARM: Use struct syscore_ops instead of sysdevs for PM in common code
On some arches (x86, sh, arm, unicore, powerpc) the oops message would
print out the last sysfs file accessed.
This was very useful in finding a number of sysfs and driver core bugs
in the 2.5 and early 2.6 development days, but it has been a number of
years since this file has actually helped in debugging anything that
couldn't also be trivially determined from the stack traceback.
So it's time to delete the line. This is good as we need all the space
we can get for oops messages at times on consoles.
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make some PowerPC architecture's code use struct syscore_ops
objects for power management instead of sysdev classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch drops the reference to a global 'cmd_line' variable from
early_init_dt_scan_chosen, and instead passes the pointer to the command
line string via the *data argument. Each architecture does something
slightly different with the initial command line, so it makes sense for
the architecture to be able to specify the variable name.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Following dump is observed on host when clearing the exit timing counters
[root@p1021mds kvm]# echo -n 'c' > vm1200_vcpu0_timing
INFO: task echo:1276 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
echo D 0ff5bf94 0 1276 1190 0x00000000
Call Trace:
[c2157e40] [c0007908] __switch_to+0x9c/0xc4
[c2157e50] [c040293c] schedule+0x1b4/0x3bc
[c2157e90] [c04032dc] __mutex_lock_slowpath+0x74/0xc0
[c2157ec0] [c00369e4] kvmppc_init_timing_stats+0x20/0xb8
[c2157ed0] [c0036b00] kvmppc_exit_timing_write+0x84/0x98
[c2157ef0] [c00b9f90] vfs_write+0xc0/0x16c
[c2157f10] [c00ba284] sys_write+0x4c/0x90
[c2157f40] [c000e320] ret_from_syscall+0x0/0x3c
The vcpu->mutex is used by kvm_ioctl_* (KVM_RUN etc) and same was
used when clearing the stats (in kvmppc_init_timing_stats()). What happens
is that when the guest is idle then it held the vcpu->mutx. While the
exiting timing process waits for guest to release the vcpu->mutex and
a hang state is reached.
Now using seprate lock for exit timing stats.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We make use of ptrace_get_breakpoints() / ptrace_put_breakpoints() to
protect ptrace_set_debugreg() even if CONFIG_HAVE_HW_BREAKPOINT if off.
However in this case, these APIs are not implemented.
To fix this, push the protection down inside the relevant ifdef.
Best would be to export the code inside
CONFIG_HAVE_HW_BREAKPOINT into a standalone function to cleanup
the ifdefury there and call the breakpoint ref API inside. But
as it is more invasive, this should be rather made in an -rc1.
Fixes this build error:
arch/powerpc/kernel/ptrace.c:1594: error: implicit declaration of function 'ptrace_get_breakpoints' make[2]: ***
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: LPPC <linuxppc-dev@lists.ozlabs.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1304639598-4707-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a platform for the Wire Speed Processor, based on the PPC A2.
This includes code for the ICS & OPB interrupt controllers, as well
as a SCOM backend, and SCOM based cpu bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For adapters which have devices under a PCIe switch/bridge it is informative
to display information for both the PCIe switch/bridge and the device on
which the bus error was detected.
rebased to powerpc-next
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
slb0_limit() wasn't a very descriptive name. This changes it along with
a comment explaining what it's used for, and provides a 64-bit BookE
implementation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for handling IO Event interrupts which come
through at the /event-sources/ibm,io-events device tree node.
The interrupts come through ibm,io-events device tree node are generated
by the firmware to report IO events. The firmware uses the same interrupt
to report multiple types of events for multiple devices. Each device may
have its own event handler. This patch implements a plateform interrupt
handler that is triggered by the IO event interrupts come through
ibm,io-events device tree node, pull in the IO events from RTAS and call
device event handlers registered in the notifier list.
Device event handlers are expected to use atomic_notifier_chain_register()
and atomic_notifier_chain_unregister() to register/unregister their
event handler in pseries_ioei_notifier_list list with IO event interrupt.
Device event handlers are responsible to identify if the event belongs
to the device event handler. The device event handle should return NOTIFY_OK
after the event is handled if the event belongs to the device event handler,
or NOTIFY_DONE otherwise.
Signed-off-by: Tseng-Hui (Frank) Lin <thlin@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds definitions of non-IBM specific v6 extended log
definitions to rtas.h.
Signed-off-by: Tseng-Hui (Frank) Lin <tsenglin@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Due to a collision between NO_CONTEXT->MMU_NO_CONTEXT change and
Anton's patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a multiple message send syscall and is the send
version of the existing recvmmsg syscall. This is heavily
based on the patch by Arnaldo that added recvmmsg.
I wrote a microbenchmark to test the performance gains of using
this new syscall:
http://ozlabs.org/~anton/junkcode/sendmmsg_test.c
The test was run on a ppc64 box with a 10 Gbit network card. The
benchmark can send both UDP and RAW ethernet packets.
64B UDP
batch pkts/sec
1 804570
2 872800 (+ 8 %)
4 916556 (+14 %)
8 939712 (+17 %)
16 952688 (+18 %)
32 956448 (+19 %)
64 964800 (+20 %)
64B raw socket
batch pkts/sec
1 1201449
2 1350028 (+12 %)
4 1461416 (+22 %)
8 1513080 (+26 %)
16 1541216 (+28 %)
32 1553440 (+29 %)
64 1557888 (+30 %)
We see a 20% improvement in throughput on UDP send and 30%
on raw socket send.
[ Add sparc syscall entries. -DaveM ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fundamental reset is an optional reset type supported only by PCIe adapters.
Handle the unexpected case where a non-PCIe device has requested a
fundamental reset. Try hot-reset as a fallback to handle this case.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For multifunction adapters with a PCI bridge or switch as the device
at the Partitionable Endpoint(PE), if one or more devices below PE
sets dev->needs_freset, that value will be set for the PE device.
In other words, if any device below PE requires a fundamental reset
the PE will request a fundamental reset.
Signed-off-by: Richard A Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for page coalescing, which is a feature on IBM Power servers
which allows for coalescing identical pages between logical partitions.
Hint text pages as coalesce candidates, since they are the most likely
pages to be able to be coalesced between partitions. This patch also
exports some page coalescing statistics available from firmware via
lparcfg.
[BenH: Moved a couple of things around to fix compile problems]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b987812b3f left
crash_kexec_wait_realmode() undefined for UP.
Commit 7c7a81b53e defined it for UP but
left it undefined for 32-bit SMP.
Seems like people are getting confused by nested #ifdef's, so move the
definitions of crash_kexec_wait_realmode() after the #ifdef CONFIG_SMP
section.
Compile-tested with 32-bit UP, 32-bit SMP and 64-bit SMP configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adapt new API.
Almost change is trivial. Most important change is the below line
because we plan to change task->cpus_allowed implementation.
- ctx->cpus_allowed = current->cpus_allowed;
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent 64-bit server processors (POWER6 and POWER7) have a "Come-From
Address Register" (CFAR), that records the address of the most recent
branch or rfid (return from interrupt) instruction for debugging purposes.
This saves the value of the CFAR in the exception entry code and stores
it in the exception frame. We also make xmon print the CFAR value in
its register dump code.
Rather than extend the pt_regs struct at this time, we steal the orig_gpr3
field, which is only used for system calls, and use it for the CFAR value
for all exceptions/interrupts other than system calls. This means we
don't save the CFAR on system calls, which is not a great problem since
system calls tend not to happen unexpectedly, and also avoids adding the
overhead of reading the CFAR to the system call entry path.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we take an interrupt or exception from kernel mode and the stack
pointer is obviously not a kernel address (i.e. the top bit is 0), we
switch to an emergency stack, save register values and panic. However,
on 64-bit server machines, we don't actually save the values of r9 - r13
at the time of the interrupt, but rather values corrupted by the
exception entry code for r12-r13, and nothing at all for r9-r11.
This fixes it by passing a pointer to the register save area in the paca
through to the bad_stack code in r3. The register values are saved in
one of the paca register save areas (depending on which exception this
is). Using the pointer in r3, the bad_stack code now retrieves the
saved values of r9 - r13 and stores them in the exception frame on the
emergency stack. This also stores the normal exception frame marker
("regshere") in the exception frame.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Icswx is a PowerPC instruction to send data to a co-processor. On Book-S
processors the LPAR_ID and process ID (PID) of the owning process are
registered in the window context of the co-processor at initialization
time. When the icswx instruction is executed the L2 generates a cop-reg
transaction on PowerBus. The transaction has no address and the
processor does not perform an MMU access to authenticate the transaction.
The co-processor compares the LPAR_ID and the PID included in the
transaction and the LPAR_ID and PID held in the window context to
determine if the process is authorized to generate the transaction.
The OS needs to assign a 16-bit PID for the process. This cop-PID needs
to be updated during context switch. The cop-PID needs to be destroyed
when the context is destroyed.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Tseng-Hui (Frank) Lin <thlin@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This removes MMU_FTR_TLBIE_206 as we can now use CPU_FTR_HVMODE_206. It
also changes the logic to select which tlbie to use to be based on this
new CPU feature bit.
This also duplicates the ASM_FTR_IF/SET/CLR defines for CPU features
(copied from MMU features).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
sysctl: net: call unregister_net_sysctl_table where needed
Revert: veth: remove unneeded ifname code from veth_newlink()
smsc95xx: fix reset check
tg3: Fix failure to enable WoL by default when possible
networking: inappropriate ioctl operation should return ENOTTY
amd8111e: trivial typo spelling: Negotitate -> Negotiate
ipv4: don't spam dmesg with "Using LC-trie" messages
af_unix: Only allow recv on connected seqpacket sockets.
mii: add support of pause frames in mii_get_an
net: ftmac100: fix scheduling while atomic during PHY link status change
usbnet: Transfer of maintainership
usbnet: add support for some Huawei modems with cdc-ether ports
bnx2: cancel timer on device removal
iwl4965: fix "Received BA when not expected"
iwlagn: fix "Received BA when not expected"
dsa/mv88e6131: fix unknown multicast/broadcast forwarding on mv88e6085
usbnet: Resubmit interrupt URB if device is open
iwl4965: fix "TX Power requested while scanning"
iwlegacy: led stay solid on when no traffic
b43: trivial: update module info about ucode16_mimo firmware
...
Added support for ibm,configure-pe RTAS call introduced with
PAPR 2.2.
Signed-off-by: Richard A. Lary <rlary@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the 64bit PPC CPU features are MMU-related, so this patch moves
them to MMU_FTR_ bits. All cpu_has_feature()-style tests are moved to
mmu_has_feature(), and seven feature bits are freed as a result.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS returns extended error codes as a hint of how long the
OS might want to wait before retrying a call. If we have nothing
else useful to do we may as well call back straight away.
This was found when testing the new dynamic dma window feature.
Firmware split the zeroing of the TCE table into 32k chunks but
returned 9901 (which is a suggested wait of 10ms). All up this took
about 10 minutes to complete since msleep is jiffies based and will
round 10ms up to 20ms.
With the patch below we take 3 seconds to complete the same test.
The hint firmware is returning in the RTAS call should definitely
be decreased, but even if we slept 1ms each iteration this would
take 32s.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The calculation of the size for the exception save area of the TLB
miss handler is wrong, luckily it's too big not too small.
Rework it to make it a bit clearer, and also correct. We want 3 save
areas, each EX_TLB_SIZE _bytes_.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We check MSR_SF a lot in sstep.c, to decide if we need to emulate the
truncation of values when running in 32-bit mode. Factor out that code
into a helper, and convert it and the other uses to use MSR_64BIT.
This fixes a bug on BOOK3E where kprobes would end up returning to a
32-bit address, because regs->nip was truncated, because (msr & MSR_SF)
was false.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new MSR_64BIT in a few places. Some of these are already ifdef'ed
for BOOKE vs BOOKS, but it's still clearer, MSR_SF does not immediately
parse as "MSR bit for 64bit".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MSR bit which indicates 64-bit-ness is different between server and
booke, so add a #define which gives you the right mask regardless.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BT_L2CAP and BT_SCO have changed to bool .
Value 'm' has invalid .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit ec775d0e70 ("powerpc: Convert to new irq_*
function names") changed a call from set_irq_chip_data() to
irq_set_chip_data(), but forgot to update the corresponding debug message
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This can be useful for differentiating interrupts on the same host
but with different chip data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we don't find ibm,associativity-reference-points as a child of
/rtas, look for it at the root of the tree instead. We use this on
Book3E where we have no RTAS but still use the sPAPR conventions
for NUMA.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Even when no initfunc is provided.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The goal is to avoid adding overhead to MMIO when only PIO is needed
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The DSCR (aka Data Stream Control Register) is supported on some
server PowerPC chips and allow some control over the prefetch
of data streams.
This patch allows the value to be specified per thread by emulating
the corresponding mfspr and mtspr instructions. Children of such
threads inherit the value. Other threads use a default value that
can be specified in sysfs - /sys/devices/system/cpu/dscr_default.
If a thread starts with non default value in the sysfs entry,
all children threads inherit this non default value even if
the sysfs value is changed later.
Signed-off-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we set up the TLB for ourselves on Book3E, we need to flush out any
old mappings established by the firmware or bootloader. At present we
attempt this with a tlbilx to flush everything, but this will leave behind
any entries with the IPROT bit set.
There are several good reason firmware might establish mappings with IPROT,
and in fact ePAPR compliant firmwares are required to establish their
initial mapped area with IPROT.
This patch, therefore adds more complex code to scan through the TLB upon
entry and flush away any entries that are not our own.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An erratum on A2 can lead to the bolted entry we insert for the linear
mapping being evicted, to avoid that write the bolted entry to way 3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In exc_lvl_ctx_init() we index into the crit/dbg/mcheck stacks using
the hard cpu id, but that assumes the hard cpu id is zero based and
contiguous. That is not the case on A2.
The root of the problem is that the 32bit code has no equivalent of the
paca to allow it to do the hard->soft mapping in assembler. Until the
32bit code is updated to handle that, index the stacks using the soft
cpu ids on 64bit and hard on 32 bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the cputable entry, regs and setup & restore entries for
the PowerPC A2 core.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While the tracer accesses ptrace breakpoints, the child task may
concurrently exit due to a SIGKILL and thus release its breakpoints
at the same time. We can then dereference some freed pointers.
To fix this, hold a reference on the child breakpoints before
manipulating them.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Prasad <prasad@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: v2.6.33.. <stable@kernel.org>
Link: http://lkml.kernel.org/r/1302284067-7860-4-git-send-email-fweisbec@gmail.com
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As well as searching for nodes with type = "nvram", search for nodes
that have compatible = "nvram". This can't be converted into a single
call to of_find_compatible_node() with a non-NULL type, because that
searches for a node that has _both_ type & compatible = "nvram".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An upcoming new ics backend will need to implement different matching
semantics to the current ones, which are essentially the RTAS ics
backends. So move the current match into the RTAS backend, and allow
other ics backends to override.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SCOM is a side-band configuration bus implemented on some processors.
This code provides a way for code to map and operate on devices via
SCOM, while the details of how that is implemented is left up to a
SCOM "controller" in the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few places we patch instructions without using
patch_instruction and patch_branch, probably because they
predated it. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we allocate the stale_map for a cpu when it comes online,
this leaves open a small window where a process can be scheduled
on the cpu before the stale_map is allocated. Instead allocate
the stale_map at CPU_UP_PREPARE time, that way it will be always
available before tasks start running.
It is possible the cpu fails to come up, in which case we should free
the stale_map, so add a CPU_UP_CANCELED case to do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a first cut at making bootwrapper code which will
produce a zImage compliant with the requirements set down
by ePAPR.
This is a very simple bootwrapper, taking the device tree
blob supplied by the ePAPR boot program and passing it on
to the kernel. It builds on the earlier patch to build a
relocatable ET_DYN zImage to meet the other ePAPR image
requirements.
For good measure we have some paranoid checks which will
generate warnings if some of the ePAPR entry condition
guarantees are not met.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds code, linker script and makefile support to allow
building the zImage wrapper around the kernel as a position independent
executable. This results in an ET_DYN instead of an ET_EXEC ELF output
file, which can be loaded at any location by the firmware and will
process its own relocations to work correctly at the loaded address.
This is of interest particularly since the standard ePAPR image format
must be an ET_DYN (although this patch alone is not sufficient to
produce a fully ePAPR compliant boot image).
Note for now we don't enable building with -pie for anything.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Book3E, MMU_NO_CONTEXT != 0, but the slice_mm_new_context()
macro assumes that it is. This means that the map of the
page sizes for each slice is always initialized to zeroes
(which happens to be 4k pages), rather than to the correct
default base page size value - which might be 64k.
This patch corrects the problem.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use MMU_NO_CONTEXT as the initialiser for mm_context.id on
nohash and hash64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to do that to guarantee they see any code change done by
dynamic patching during boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wakeup comes from the system reset handler with a potential loss of
the non-hypervisor CPU state. We save the non-volatile state on the
stack and a pointer to it in the PACA, which the system reset handler
uses to restore things
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to wait a bit for them to have done their CPU setup
or we might end up with translation and EE on with different
LPCR values between threads
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We do it before we loop on the PACA start flag. This way, we get a
chance to set critical SPRs on all CPUs before Linux tries to start
them up, which avoids problems when changing some bits such as LPCR
bits that need to be identical on all threads of a core or similar
things like that. Ideally, some of that should also be done before
the MMU is enabled, but that's a separate issue which would require
moving some of the SMP startup code earlier, let's not get there
for now, it works with that change alone.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This sets the default data stream prefetch size for operating
systems that don't set their own value in DSCR. We use 4 which
is "medium".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses feature sections to arrange that we always use HSPRG1
as the scratch register in the interrupt entry code rather than
SPRG2 when we're running in hypervisor mode on POWER7. This will
ensure that we don't trash the guest's SPRG2 when we are running
KVM guests. To simplify the code, we define GET_SCRATCH0() and
SET_SCRATCH0() macros like the GET_PACA/SET_PACA macros.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework exception macros a bit to split offset from vector and add
some basic support for HDEC, HDSI, HISI and a few more.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pass the register type to the prolog, also provides alternate "HV"
version of hardware interrupt (0x500) and adjust LPES accordingly
We tag those interrupts by setting bit 0x2 in the trap number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When running in Hypervisor mode (arch 2.06 or later), we store the PACA
in HSPRG0 instead of SPRG1. The architecture specifies that SPRGs may be
lost during a "nap" power management operation (though they aren't
currently on POWER7) and this enables use of SPRG1 by KVM guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This bit indicates that we are operating in hypervisor mode on a CPU
compliant to architecture 2.06 or later (currently server only).
We set it on POWER7 and have a boot-time CPU setup function that
clears it if MSR:HV isn't set (booting under a hypervisor).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Even when nothing is specified in the device tree, and despite the
fact that we don't setup links properly yet, we still need a reasonable
value in there or some interrupts won't be setup properly to point to
an existing processor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds more SPR definitions used on newer processors when running
in hypervisor mode. Along with some other P7 specific bits and pieces
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a significant rework of the XICS driver, too significant to
conveniently break it up into a series of smaller patches to be honest.
The driver is moved to a more generic location to allow new platforms
to use it, and is broken up into separate ICP and ICS "backends". For
now we have the native and "hypervisor" ICP backends and one common
RTAS ICS backend.
The driver supports one ICP backend instanciation, and many ICS ones,
in order to accomodate future platforms with multiple possibly different
interrupt "sources" mechanisms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This problem was noticed on an MPC855T platform. Ftrace did oops
when trying to write to the kernel text segment.
Many thanks to Joakim for finding the root cause of this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
...
.scan_dispatch_log+0xb0/0x170
.account_system_vtime+0xa0/0x220
.irq_enter+0x88/0xc0
.do_IRQ+0x48/0x230
The patch below adds a check to scan_dispatch_log to ensure the
dispatch log has been allocated.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PAPR specifies that DTL buffers can not cross AMS environments (aka CMO
in the PAPR) and can not cross a memory entitlement granule boundary
(4k). This is found in section 14.11.3.2 H_REGISTER_VPA of the PAPR.
kmalloc does not guarantee an alignment of the allocation, though,
beyond 8 bytes (at least in my understanding). Create a special kmem
cache for DTL buffers with the alignment requirement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent commit b987812b3f caused
a compile failure on UP because a considerably large block
of the file was included within CONFIG_SMP, hence making a stub
function not exposed on UP builds when it needed to be.
Relocate the stub to the #else /* ! CONFIG_SMP */ section
and also annotate the relevant else/endif so that nobody
else falls into the same trap I did.
Reported-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
We currently dont have CPU Hotplug support working on 85xx so we need to
disable Suspsend support as it will force enabling of CPU Hotplug.
arch/powerpc/kernel/built-in.o: In function `cpu_die': arch/powerpc/kernel/smp.c:702: undefined reference to `start_secondary_resume'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
e500mc does not support the HID0/MSR mechanism that is used by e500_idle
(and there are also issues with waking on certain types of interrupts).
Further, even if napping is never actually enabled, just having
CPU_FTR_CAN_NAP will cause machine_init() to overwrite the board's supplied
ppc_md.power_save().
We drop CPU_FTR_MAYBE_CAN_DOZE becuase we should use 'wait' instead on
e500mc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPU_FTRS_POSSIBLE and CPU_FTRS_ALWAYS defines did not encompass
e5500 CPU features when built for 64-bit. This causes issues with
cpu_has_feature() as it utilizes the POSSIBLE & ALWAYS defines as part
of its check.
Create a unique CPU_FTRS_E5500 (as its different from CPU_FTRS_E500MC),
created a new group for 64-bit Book3e based CPUs and add CPU_FTRS_E5500
to that group.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
serial port nodes with the property status="disabled" are not usable and so
avoid adding "disabled" port with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCIe nodes with the property status="disabled" are not usable and so
avoid adding "disabled" PCIe bridge with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose. However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation. Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.
To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it. Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Commit b3df895aeb "powerpc/kexec: Add support for FSL-BookE"
introduced the original PPC_STD_MMU_64 checks around the function
crash_kexec_wait_realmode(). Then commit c2be05481f
"powerpc: Fix default_machine_crash_shutdown #ifdef botch" changed
the ifdef around the calling site to add a check on SMP, but the
ifdef around the function itself was left unchanged, leaving an
unused function for PPC_STD_MMU_64=y and SMP=n
Rather than have two ifdefs that can get out of sync like this,
simply put the corrected conditional around the function and use
a stub to get rid of one set of ifdefs completely.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some minor typos:
* informations => information
* there own => their own
* these => this
Signed-off-by: Sylvestre Ledru <sylvestre.ledru@scilab.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCIe memory address space is 1:1 mapped with u-boot.
Update dts of Px020RDB i.e. P1020RDB and P2020RDB to match the address map
changes in u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Instead of creating idle threads at boot for all possible CPUs, we
create them on demand, like x86 or ARM, and we properly call init_idle
to re-initialize an idle thread when a CPU was unplugged and is now
re-plugged.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On some machines that use i2c to synchronize the timebases (such
as PowerMac7,2/7,3 G5 machines), hotplug CPU would crash when
putting back a new CPU online due to the underlying i2c bus being
closed.
This uses the newly added bringup_done() callback to move the close
along with other housekeeping calls, and adds a CPU notifier to
re-open the i2c bus around subsequent hotplug operations
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows us to stop abusing smp_ops->setup_cpu() for cleanup
tasks that have to take place after the initial boot time CPU
bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code soft-disables, and then goes to NAP mode which
turns interrupts on. That means that if an interrupt occurs, we
will hit the masked interrupt code path which isn't what we want,
as it will return with EE off, which will either get us out of
NAP mode, or fail to enter it (according to spec).
Instead, let's just rely on the fact that it is safe to take
decrementer interrupts on an offline CPU and leave interrupts
enabled. We can also get rid of the special case in asm for
power4_cpu_offline_powersave() and just use power4_idle().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those instructions do nothing on non-threaded processors such
as 970's used on those machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the generic code, just add the MPIC priority setting,
I don't see any use in mucking around with the decrementer,
as 32-bit will have EE off all along, and 64-bit will be able
to deal with it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
Remove the last remnants of cpu_enable(), everybody uses the normal
__cpu_up() path now
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Milton Miller