commit 8b9ade9f74 coming from Viresh Kumar "tty: serial: sirfsoc: drop
uart_port->lock before calling tty_flip_buffer_push()" broke sirfsoc uart
driver by knic:
[ 5.129122] BUG: spinlock already unlocked on CPU#0, ip6tables/1331
[ 5.132554] lock: sirfsoc_uart_ports+0x4/0x8a0, .magic: dead4ead,
.owner: <none>/-1, .owner_cpu: -1
[ 5.141651] CPU: 0 PID: 1331 Comm: ip6tables Tainted: G
W O 3.10.16 #3
[ 5.148866] [<c0013528>] (unwind_backtrace+0x0/0xe0) from
[<c0010e70>] (show_stack+0x10/0x14)
[ 5.157362] [<c0010e70>] (show_stack+0x10/0x14) from
[<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8)
[ 5.166125] [<c01a5e68>] (do_raw_spin_unlock+0x40/0xc8) from
[<c03ff8b4>] (_raw_spin_unlock+0x8/0x40)
[ 5.175322] [<c03ff8b4>] (_raw_spin_unlock+0x8/0x40) from
[<c0203fcc>] (sirfsoc_uart_pio_rx_chars+0xa4/0xc0)
[ 5.185120] [<c0203fcc>]
(sirfsoc_uart_pio_rx_chars+0xa4/0xc0) from [<c0204fb8>]
(sirfsoc_rx_tmo_process_tl+0xdc/0x1e0)
[ 5.195875] [<c0204fb8>]
(sirfsoc_rx_tmo_process_tl+0xdc/0x1e0) from [<c0024b50>]
(tasklet_action+0x8c/0xec)
[ 5.205673] [<c0024b50>] (tasklet_action+0x8c/0xec) from
[<c00242a8>] (__do_softirq+0xec/0x1d4)
[ 5.214347] [<c00242a8>] (__do_softirq+0xec/0x1d4) from
[<c0024428>] (do_softirq+0x48/0x54)
[ 5.222674] [<c0024428>] (do_softirq+0x48/0x54) from
[<c0024690>] (irq_exit+0x74/0xc0)
[ 5.230573] [<c0024690>] (irq_exit+0x74/0xc0) from
[<c000e1e8>] (handle_IRQ+0x6c/0x90)
[ 5.238465] [<c000e1e8>] (handle_IRQ+0x6c/0x90) from
[<c000d500>] (__irq_svc+0x40/0x70)
[ 5.246446] [<c000d500>] (__irq_svc+0x40/0x70) from
[<c0092e7c>] (mark_page_accessed+0xc/0x68)
[ 5.255034] [<c0092e7c>] (mark_page_accessed+0xc/0x68) from
[<c00a2a4c>] (unmap_single_vma+0x3bc/0x550)
[ 5.264402] [<c00a2a4c>] (unmap_single_vma+0x3bc/0x550) from
[<c00a3b4c>] (unmap_vmas+0x44/0x54)
[ 5.273164] [<c00a3b4c>] (unmap_vmas+0x44/0x54) from
[<c00a81a8>] (exit_mmap+0xc4/0x1e0)
[ 5.281233] [<c00a81a8>] (exit_mmap+0xc4/0x1e0) from
[<c001bb78>] (mmput+0x3c/0xdc)
[ 5.288868] [<c001bb78>] (mmput+0x3c/0xdc) from [<c0021b0c>]
(do_exit+0x30c/0x828)
[ 5.296413] [<c0021b0c>] (do_exit+0x30c/0x828) from
[<c0022dac>] (do_group_exit+0x4c/0xb0)
[ 5.304653] [<c0022dac>] (do_group_exit+0x4c/0xb0) from
[<c0022e20>] (__wake_up_parent+0x0/0x18)
Root cause:
the commit dropped uart_port->lock before calling tty_flip_buffer_push(), but in sirfsoc-uart,
sirfsoc_uart_pio_rx_chars() can be called by sirfsoc_rx_tmo_process_tl(). here uart_port->lock
has not been taken yet. so that caused unpaired lock/unlock.
Solution:
This patch is doing a quick fix for that, it adds spin_lock/unlock(&port->lock) protect to
sirfsoc_uart_pio_rx_chars() in sirfsoc_rx_tmo_process_tl() to keep spin_lock/unlock in pair.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aparently 9865 uses standard BAR encoding scheme (unlike 99xx cards).
Current pci_netmos_9900_setup() uses wrong BAR indices for the 9865 PCI
device, function 2. Using standard BAR indices makes all 6 ports work
for me. Thus disable the NetMos 9900 quirk for NetMos 9865 pci device.
For the reference, here is the relevant part of lspci for my device:
02:07.0 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at ac00 [size=8]
Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.1 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
Subsystem: Device a000:1000
Flags: bus master, medium devsel, latency 32, IRQ 18
I/O ports at a800 [size=8]
Memory at fcffd000 (32-bit, non-prefetchable) [size=4K]
Memory at fcffc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
02:07.2 Communication controller: MosChip Semiconductor Technology Ltd.
PCI 9865 Multi-I/O Controller
Subsystem: Device a000:3004
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a400 [size=8]
I/O ports at a000 [size=8]
I/O ports at 9c00 [size=8]
I/O ports at 9800 [size=8]
Memory at fcffb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [48] Power Management version 2
Kernel driver in use: serial
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the gpio is not yet available we better also
defer the probing in the rs485 case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warnings:
drivers/tty/serial/8250/8250_dw.c:404:12: warning: ‘dw8250_suspend’ defined but not used [-Wunused-function]
drivers/tty/serial/8250/8250_dw.c:413:12: warning: ‘dw8250_resume’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This can cause lots of extra messages at boot time, slowing things down. It is
caused by commit 2a0b965cfb (serial: omap: Add support for optional wake-up)
which was applied for v3.13-rc1.
This patch moves the infomessage to the probe function to display it
only once.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org> # 3.13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds devicetree support for the MAX310X serial driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes some unused definitions from driver code and
sort #includes alphabetically.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs.
As a result this patch eliminate private driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always register GPIOs and use dynamic GPIO ID assignment.
This is no much worth if GPIOs is not used, but helps remove
private driver header and add DT support in the future.
Additionally, patch adds missing uart_unregister_driver()
call if probe() fails.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes "frequency" parameter from MAX310X platform_data
and uses CLK API for getting clock. Clock type (XTAL/OSC) is
determined by clk name.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch move all SPI-dependent stuff in one place. This include move
PM-function definitions out of CONFIG_SPI_MASTER and move regmap
initialization out of common probe into CONFIG_SPI_MASTER which
may help to add I2C support in the future for this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this driver needs not depend on HAVE_CLK.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes excess IRQ checks at driver probe().
IRQ validation is already provided by request_threaded_irq().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces loopback mode support from platform data to
dynamic setup with TIOCMSET ioctl.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core calls set_termios() after port startup, so there are
no reason to setup port twice.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These callbacks were previously used for the IC power initialization.
If this initialization will be needed in the future, it should be
implemented with the regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provide more precisely setup of baud rate generator.
If the result of division has a remainder, we use the multiplier
for the base frequency. Additionally, we report result baud rate
back to serial core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware supported by the driver is only found on SUPERH or
ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST compilation to them.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_DEBUG_FS to 'char name' in order to fix the following
build warning, because 'char name' is used only when CONFIG_DEBUG_FS
is enabled.
drivers/tty/serial/pch_uart.c:1765:7: warning: unused variable 'name' [-Wunused-variable]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following compile warning about cast to pointer from
integer of different size.
drivers/tty/serial/sh-sci.c:2021:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the info message about a missing wakeirq for uart is printed
every time the serial driver's startup function is called. This happens
multiple times and not just once.
This patch moves the infomessage to the probe function to display it
only once.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the polling functionality for the MSM serial driver.
This allows us to use KGDB on this hardware.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've split Qualcomm MSM support into legacy and multiplatform. So add
the ability to build the serial driver on the newer ARCH_QCOM
multiplatform.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull MIPS updates from Ralf Baechle:
"The most notable new addition inside this pull request is the support
for MIPS's latest and greatest core called "inter/proAptiv". The
patch series describes this core as follows.
"The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit."
The platform specific patches touch all 3 Broadcom families. It adds
support for the new Broadcom/Netlogix XLP9xx Soc, building a common
BCM63XX SMP kernel for all BCM63XX SoCs regardless of core type/count
and full gpio button/led descriptions for BCM47xx.
The rest of the series are cleanups and bug fixes that are MIPS
generic and consist largely of changes that Imgtec/MIPS had published
in their linux-mti-3.10.git stable tree. Random other cleanups and
patches preparing code to be merged in 3.15"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
mips: select ARCH_MIGHT_HAVE_PC_SERIO
mips: delete non-required instances of include <linux/init.h>
MIPS: KVM: remove shadow_tlb code
MIPS: KVM: use common EHINV aware UNIQUE_ENTRYHI
mips/ide: flush dcache also if icache does not snoop dcache
MIPS: BCM47XX: fix position of cpu_wait disabling
MIPS: BCM63XX: select correct MIPS_L1_CACHE_SHIFT value
MIPS: update MIPS_L1_CACHE_SHIFT based on MIPS_L1_CACHE_SHIFT_<N>
MIPS: introduce MIPS_L1_CACHE_SHIFT_<N>
MIPS: ZBOOT: gather string functions into string.c
arch/mips/pci: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
bcma: gpio: don't cast u32 to unsigned long
ssb: gpio: add own IRQ domain
MIPS: BCM47XX: fix sparse warnings in board.c
MIPS: BCM47XX: add board detection for Linksys WRT54GS V1
MIPS: BCM47XX: fix detection for some boards
MIPS: BCM47XX: Enable buttons support on SSB
MIPS: BCM47XX: Convert WNDR4500 to new syntax
MIPS: BCM47XX: Use "timer" trigger for status LEDs
...
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Here are tiny and assorted serial driver fixes that have been in a
branch in my tree for a while and somehow did not get properly merged
into my big TTY / Serial pull request for 3.14-rc1. Sorry about that.
All have been in linux-next for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLm74UACgkQMUfUDdst+ylviACcC4eubO3yOgJzG5A69+Ncl7t6
sy0An2Kb3x0evfvmR6O+fT67rFrvBijA
=Iv/6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are tiny and assorted serial driver fixes that have been in a
branch in my tree for a while and somehow did not get properly merged
into my big TTY / Serial pull request for 3.14-rc1. Sorry about that.
All have been in linux-next for a while with no issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xuartps: Properly guard sysrq specific code
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
serial: icom: dereference after free in load_code()
serial: 8250_dw: add new ACPI IDs
tty: serial: pch: don't crash if DMA enabled but not loaded
serial: samsung: move clock deactivation below uart registration
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Now that the UART block defines have been moved to a separate file,
include that one and do not longer rely on the MIPS-specific
bcm63xx_regs.h header file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6204/
bcm_{readl,writel} macros expand to __raw_{readl,writel}, use these
directly such that we do not rely on the platform to provide these for
us. As a result, we no longer use bcm63xx_io.h, so remove that inclusion
too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6201/
bcm63xx_irqs.h is included but we are not using anything from it, drop
that include.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6205/
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This was a "forgotten" branch of tty fixes that somehow didn't make it
into my "main" branches, my fault.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Cc: stable <stable@vger.kernel.org> # v3.12
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
prepare and enable the FIFO clock upon PSC FIFO initialization,
check for and propagage errors when enabling the PSC FIFO clock,
disable and unprepare the FIFO clock upon PSC FIFO uninitialization
devm_{get,put}_clk() doesn't apply here, as the SoC provides a
single FIFO component which is shared among several PSC components,
thus the FIFO isn't associated with a device (while the PSCs are)
provide a fallback clock lookup approach in case the OF based clock
lookup for the PSC FIFO fails, this allows for successful operation in
the presence of an outdated device tree which lacks clock specs
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the PSC index,
remove the "psc%d_mclk" template and unconditionally use 'mclk'
acquire and release the "ipg" clock item for register access as well
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* qcom/drivers:
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
Signed-off-by: Olof Johansson <olof@lixom.net>
The msm_serial_hs driver uses mach specific dma APIs. This is not
compatible with the multi-platform ARM effort. Let's only compile
this driver on MSM devices that are prepared to support it;
allowing the DT based MSM devices to enter the multi-platform ARM
build.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rx dma-callback it calls tasklet_schedule, if the tasklet
be scheduled after all the dma-callback in the rx dma channel,
current check condition in the tasklet will not do fetch dma
buffer into tty because tx_issued is equal with tx_completed,
so as timeout tasklet does.
so we check whether we should fetch the whole dma buffer into
tty according to the status of transactions in rx dma channel.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch provides PM entry of uart_ops, then drop clk enable and
disable because serial core will do it.
the patch also fixes the issue that uart hang in resume caused by
not-enabled clock.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions
instead of legacy suspend and resume entries of platform_driver.
this will add hibernation support automatically as suspend to disk
entries are also set.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, read{write}_relaxed() functions was be replaced with
simple read{write}() variants. Potential "uninitialized variable"
warnings was be fixed if driver compiled without MFD_SYSCON.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=IZCI
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=BQSn
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Second Round of Renesas SH SCI updates for v3.14
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
* tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
Signed-off-by: Olof Johansson <olof@lixom.net>
Updates for the SH SCI serial driver
* Convert to clk_prepare/unprepare
* Fix warnings due to improper casts and printk formats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pxvs
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Renesas SH SCI updates for v3.14
Updates for the SH SCI serial driver
* Convert to clk_prepare/unprepare
* Fix warnings due to improper casts and printk formats
* tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Convert to clk_prepare/unprepare
serial: sh-sci: Don't enable/disable port from within break timer
serial: sh-sci: Fix warnings due to improper casts and printk formats
Signed-off-by: Olof Johansson <olof@lixom.net>
Extend the driver to with support for SCIx device tree bindings. A
minimal set of features is supported, additional properties can be added
later should the need to describe more device features arise.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The overrun bit index is a property of the hardware. It's currently
computed based on a different and unrelated hardware property, the baud
rate calculation algorithm. Compute it using hardware identification
information only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IRQ number can't be modified by the user as the port is fixed.
There's no need to check the new IRQ number as it will be ignored by the
core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The base address, IRQ and baud rate generator parent clock rate can't be
changed by userspace. Mark the port as fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver checks if the interrupt number is greater than nr_irqs and
returns an error in that case. The same check is already performed by
the caller, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This passes the errata fix using a GPIO to control the RTS pin
on one of the AT91 chips to use gpiolib instead of the
AT91-specific interfaces. Also remove the reliance on
compile-time #defines and the cpu_* check and rely on the
platform passing down the proper GPIO pin through platform
data.
This is a prerequisite for getting rid of the local GPIO
implementation in the AT91 platform and move toward
multiplatform.
The patch also adds device tree support for getting the
RTS GPIO pin from the device tree on DT boot paths.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
New driver for NXP (Philips) UART ICs was introduced in September 2012.
Old driver no longer used anywhere, this patch removes it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back from DMA to interrupt mode the receive interrupt has to
be re-enabled to catch new incoming data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In pl011_rx_chars() if pl011_dma_rx_trigger_dma() succeeds it will disable
the receive interrupt, no need to do this again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialisation, a UART may already be in use for a console, so
take care to preserve things like baud rate and data format to avoid
corrupting console output.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to cope with a split tx/rx LCR_H register is non-trivial
so put it into it's own function to avoid duplication.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17438217a6 on request
of Linus Walleij:
Greg can you please drop or revert
commit 17438217a6
"serial: pl011: use DMA RX polling by default"
from the TTY tree until this has been sorted out?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a complex patch for refactoring CLPS711X serial driver.
Major changes:
- Eliminate <mach/hardware.h> usage.
- Devicetree support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c49436b657 (serial: 8250_dw: Improve unwritable LCR workaround)
caused a regression. It added a check that the LCR was written properly
to detect and workaround the busy quirk, but the behaviour of bit 5
(UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the
docs. On older versions this caused the check to fail and it would
repeatedly force idle and rewrite the LCR register, causing delays and
preventing any input from serial being received.
This is fixed by masking out UART_LCR_SPAR before making the comparison.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Markus Mayer <markus.mayer@linaro.org>
Tested-by: Tim Kryger <tim.kryger@linaro.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
By using dma_request_slave_channel_or_err(), the DMA slave ID can be
looked up from standard DT properties, and squirrelled away during
channel allocation. Hence, there's no need to use a custom DT property
to store the slave ID.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support'
(0c0c47bc40) introduced sysrq support
without properly guarding sysrq specific code which results in build
errors when sysrq is disabled:
DNAME=KBUILD_STR(xilinx_uartps)" -c -o
drivers/tty/serial/.tmp_xilinx_uartps.o
drivers/tty/serial/xilinx_uartps.c
drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr':
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port'
has no member named 'sysrq'
make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1
Reported-by: Masanari Iida <standby24x7@gmail.com>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use "fw" in the next line after we release it. I've shifted the call
to release_firmware() down a couple lines to fix this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if the DMA driver isn't loaded "on time" then we crash in the irq handler:
| pch_uart 0000:02:0a.4: pch_request_dma:dma_request_channel FAILS(Tx)
| BUG: unable to handle kernel NULL pointer dereference at (null)
| IP: [<c0676ed9>] pch_uart_interrupt+0x739/0x940
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 60e9357547 (serial: samsung: enable clock before clearing pending
interrupts during init) added handling of the controller clock during init.
On most systems this clock is also one of the baud_clock sources and
possibly used by the earlycon and thus already enabled by the bootloader.
Therefore a gap exists between s3c24xx_serial_init_port disabling the
clock and an attached console reenabling it, making the transition from
earlycon to regular console possibly hang the system - as seen on my
S3C2442 based Freerunner today.
Therefore move the disabling of the clock from s3c24xx_serial_init_port
below the uart port registration, effectively creating an overlap and
keeping the clock running non-stop if the console wants to grab this port.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modern PM ops and use the SIMPLE_DEV_PM_OPS macro to set up
the PM callbacks.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qipan Li