This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.
Signed-off-by: Dmitry Kunilov <dmitry.kunilov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:
tty_release: ttyUSB1: read/write wait queue active!
It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: Pavel Parkhomenko <ra85551@gmail.com>
Tested-by: Pavel Parkhomenko <ra85551@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rebranded Novatel E371 for AT&T's LTE bands.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea fixes,
which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx
Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX
=JmvB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add support for Cinterion's products AH6 and PLS8 by adding Product IDs
and USB_DEVICE tuples.
Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another device using CDC ACM with vendor specific protocol to mark
serial functions.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.
The CDC ACM class driver cannot support functions with only 2
endpoints. The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.
There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding three currently unsupported modems based on information
from .inf driver files:
Diag VID_1BBB&PID_0052&MI_00
AGPS VID_1BBB&PID_0052&MI_01
VOICE VID_1BBB&PID_0052&MI_02
AT VID_1BBB&PID_0052&MI_03
Modem VID_1BBB&PID_0052&MI_05
wwan VID_1BBB&PID_0052&MI_06
Diag VID_1BBB&PID_00B6&MI_00
AT VID_1BBB&PID_00B6&MI_01
Modem VID_1BBB&PID_00B6&MI_02
wwan VID_1BBB&PID_00B6&MI_03
Diag VID_1BBB&PID_00B7&MI_00
AGPS VID_1BBB&PID_00B7&MI_01
VOICE VID_1BBB&PID_00B7&MI_02
AT VID_1BBB&PID_00B7&MI_03
Modem VID_1BBB&PID_00B7&MI_04
wwan VID_1BBB&PID_00B7&MI_05
Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on
wwan VID_1BBB&PID_0000&MI_04
wwan VID_1BBB&PID_0017&MI_06
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diagnostics VID_2357&PID_0201&MI_00
NMEA VID_2357&PID_0201&MI_01
Modem VID_2357&PID_0201&MI_03
Networkcard VID_2357&PID_0201&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
also known as Alcatel One Touch L100V LTE
The driver description files gives these names to the vendor specific
functions on this modem:
Application1: VID_1BBB&PID_011E&MI_00
Application2: VID_1BBB&PID_011E&MI_01
Modem: VID_1BBB&PID_011E&MI_03
Ethernet: VID_1BBB&PID_011E&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: Quentin.Li <snowmanli88@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Huawei E173 will normally appear as 12d1:1436 in Linux. But
the modem has another mode with different device ID and a slightly
different set of descriptors. This is the mode used by Windows like
this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003
All interfaces have the same ff/ff/ff class codes in this mode.
Blacklisting the network interface to allow it to be picked up by
the network driver.
Cc: stable <stable@vger.kernel.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The exception is needed on big endian systems too.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for a vendor specific probe exception just to
match on the interface class.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many modems in addition to the D-Link DWM 652
exposing the CD interface in modem mode, and some expose
an integrated card reader as well. Always ignore these
interfaces.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove all MODULE_VERSION macros and driver-version information (except
for garmin_gps which uses it in a status reply).
It is the kernel version that matters and not some private version
scheme which rarely even gets updated.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Note that the usb device id is stored at probe so that it can be used
in attach to determine send-setup blacklisting.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak in usb-serial probe error path by moving port
data allocation to port_probe.
Since commit a1028f0abf ("usb: usb_wwan: replace release and disconnect
with a port_remove hook") port data is deallocated in port_remove. This
leaves a possibility for memory leaks if usb-serial probe fails after
attach but before the port in question has been successfully registered.
Note that this patch also fixes two additional memory leaks in the error
path of attach should port initialisation fail for any port as the urbs
were never freed and neither was the data of any of the successfully
initialised ports.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on information from the ZTE Windows drivers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this patch, we add new declarations into option.c to support the new
interfaces of Huawei Data Card devices. And at the same time, remove the
redundant declarations from option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is also known as the Verizon USB551L.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Determine whether to use send_setup at probe time rather than at every
call to send_setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up option probe by introducing intermediate variables and fixing
up comments.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the changes to the option driver, which are needed
for follow-on patches from Johan.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_{get,set}_serial_data to access usb-serial data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak introduced by commit 383cedc3bb ("USB: serial:
full autosuspend support for the option driver") which allocates
usb-serial data but never frees it.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b4c6a3ab5 ("USB: option: Use generic USB wwan code")
moved option port-data allocation to usb_wwan_startup but still cast the
port data to the old struct...
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Later firmwares for this device now have proper subclass and
protocol info so we can identify it nicely without needing to use
the blacklist. I'm not removing the old 0xff matching as there
may be devices in the field that still need that.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reworks the usb_serial_register_drivers() and
usb_serial_deregister_drivers() to not need a pointer to a struct
usb_driver anymore. The usb_driver structure is now created dynamically
and registered and unregistered as needed.
This saves lines of code in each usb-serial driver. All in-kernel users
of these functions were also fixed up at this time. The pl2303 driver
was tested that everything worked properly.
Thanks for the idea to do this from Alan Stern.
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Support Department <support@connecttech.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now set by the usb-serial core, no need for the driver to
individually set it.
Thanks to Alan Stern for the idea to get rid of it.
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Support Department <support@connecttech.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Julia Lawall <julia@diku.dk>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now set by the usb-serial core, no need for the driver to
individually set it.
Thanks to Alan Stern for the idea to get rid of it.
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Support Department <support@connecttech.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Julia Lawall <julia@diku.dk>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1551) cleans up the PM-related entries in the usb_driver
structures of the various USB serial driver modules. Those entries
are now filled in by the usb-serial core during driver registration,
so they don't need to be initialized explicitly in the source code.
The same is true of the one remaining no_dynamic_id entry.
reset_resume remains a small problem, because the serial core doesn't
support it. The patch ignores these entries.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These interfaces need to be handled by QMI/WWAN driver
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device presents a total of 5 interfaces with ff/ff/ff
class/subclass/protocol. The last one of these is verified
to be a QMI/wwan combined interface which should be handled
by the qmi_wwan driver, so we blacklist it here.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d905fd "USB: option: convert Huawei K3765, K4505, K4605
reservered interface to blacklist" accidentally ANDed two
blacklist tests by leaving out a return. This was not noticed
because the two consecutive bracketless if statements made it
syntactically correct.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the option.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1527) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
navman, omninet, opticon, option, oti6858, and pl2303.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Remove all old mass-storage ids's pid:
0x0026,0x0053,0x0098,0x0099,0x0149,0x0150,0x0160;
2. As the pid from 0x1401 to 0x1510 which have not surely assigned to
use for serial-port or mass-storage port,so i think it should be
removed now, and will re-add after it have assigned in future;
3. sort the pid to WCDMA and CDMA.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As ZTE have and will use more pid for new products this year,
so we need to add some new zte 3g-dongle's pid on option.c ,
and delete one pid 0x0154 because it use for mass-storage port.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksander Morgado